Spectrophotometric determination of trace permanganate in water with N,N-diethyl-p-phenylenediamine (DPD)

A Novel Spectrophotometric Method for Determination of Percarbonate by Using N, N-Diethyl-P-Phenylenediamine as an Indicator and Its Application in Activated Percarbonate Degradation of Ibuprofen

Sodium percarbonate (SPC) concentration can be determined spectrophotometrically by using N, N-diethyl-p-phenylenediamine (DPD) as an indicator for the first time. The ultraviolet-visible spectrophotometry absorbance of DPD•+ measured at 551 nm was used to indicate SPC concentration. The method had good linearity (R2 = 0.9995) under the optimized experimental conditions (pH value = 3.50, DPD = 4 mM, Fe2+ = 0.5 mM, and t = 4 min) when the concentration of SPC was in the range of 0-50 μM. The blank spiked recovery of SPC was 95-105%. The detection limit and quantitative limit were 0.7-1.0 μM and 2.5-3.3 μM, respectively. The absorbance values of DPD•+ remained stable within 4-20 min. The method was tolerant to natural water matrix and low concentration of hydroxylamine (<0.8 mM). The reaction stoichiometric efficiency of SPC-based advanced oxidation processes in the degradation of ibuprofen was assessed by the utilization rate of SPC. The DPD and the wastewater from the reaction were non-toxic to Escherichia coli. Therefore, the novel Fe2+/SPC-DPD spectrophotometry proposed in this work can be used for accurate and safe measurement of SPC in water.

Engineered organotin(IV) and vanadium(V) derivatives with distinct coordination modes and luminescent properties for the efficient detection and quantification of permanganate ions

The distinction in coordination modes of metal complexes leads to their versatile structural features and unique properties. Here, we report two tetradentate Schiff base ligands (H₂L¹ and H₂L²) bearing N₂O₂ donor sets, tactically selected to provide distinct coordination modes with different metal ions. The ligands were utilized to synthesize their organotin(IV) (1-4) and vanadium(V) (5) derivatives. The synthesized compounds were characterized using elemental analysis, FT-IR spectroscopy, multi-nuclei NMR (¹H, ¹³C, and ¹¹⁹Sn) spectroscopy, mass spectrometry, and single-crystal X-ray diffraction. The organotin(IV) derivatives (1-4) displayed hepta-coordination around both the Sn centres as they were achieved in their dimeric form. Contrariwise, the vanadium(V) compound (5) was isolated as a mononuclear entity exhibiting penta-coordinated geometry around the vanadium centre. The variation in the coordination modes was evident in their UV-vis and fluorescence spectra. The organotin(IV) compounds (1-4) exhibited a strong emission band centred at 468 nm when excited at a wavelength of 360 nm whereas the vanadium(V) (5) derivative displayed poor fluorogenic response. Compound 1 was further explored for the fluorogenic chemo-sensing of permanganate ions (MnO₄^-) amongst various anions by quenching response. A detailed investigation of the recognition of permanganate ions was accomplished by spectrofluorometric, spectroscopic (¹¹⁹Sn NMR), mass spectrometric, and computational studies.

Determination of trace potassium permanganate in tap water by solid phase extraction combined with spectrophotometry

A simple solid phase extraction (SPE) coupled with spectrophotometric method was developed for determination of trace permanganate (MnO₄ ^-) in water. Commercial reagent polyamined-6 powder was used as SPE stationary phase to retain MnO₄ ^- which is based on the fact that MnO₄ ^- can be adsorbed on polyamide 6 (PA-6) sorbent as water samples flow through the SPE cartridge. 3,3',5,5'-tetramethylbenzidine (TMB) were used both as eluent solution and chromogenic agent to convert the adsorbed MnO₄ ^- into Mn²⁺ and generate blue oxidized product with high molar absorptivity. Quantification of MnO₄ ^- could be obtained by spectrophotometric detection of the resulting solution flow out of the SPE cartridge. The extraction and detection variables was optimized to maximize the absorbance of the TMB oxidized product. Under optimized conditions, this method provided linear dynamic ranges of 0.01-1 μmol L^-1 for MnO₄ ^- with preconcentration of 100 mL water sample. The limits of detection (3S_b/m) of this method in deionized water were calculated to be 5.1 nM, and the relative standard deviations were determined to be 3.2% (C = 0.1 μmol L^-1, n = 5). This method has been applied to the determination of MnO₄ ^- in spiked tap waters and satisfactory recovery was obtained.

A Critical Review on Chemical Speciation of Chlorine-Produced Oxidants (CPOs) in Seawater. Part 2: Sampling, Sample Preparation and Non-Chromatographic and Mass Spectrometric-Based Methods

Chlorination of seawater forms a range of secondary oxidative species, collectively termed "chlorine-produced oxidants" (CPOs). These compounds do not have the same biocidal efficacy, the same fate and behavior in the marine environment, the same potential formation of chlorination by-products (CBPs), nor the same effects on marine organisms. Their chemical speciation is an important step toward an accurate assessment of the effectiveness of chlorination and the potential impacts of its releases, among others. The aim of this paper - which is the second of a trilogy dedicated to the chemical speciation of CPOs in seawater - is to cover all aspects related to CPOs analysis in seawater, from sampling to instrumental determination. First, it discusses the procedures involved in synthesis, storage, and standardization of analytical standards. Second, it deals with sampling and sample preparation, addressing all relevant issues related to these two key steps. Third, it provides a comprehensive and up-to-date overview of the colorimetric, titrimetric, and electrochemical methods used for CPOs determination and thoroughly discusses their advantages and limitations. Finally, this review ends with some recommendations for progress in the field of CPO analysis with the three aforementioned approaches. Chromatographic and mass spectrometric-based methods will be covered in the third and final article (Part III).

Spectrophotometric determination of hydrogen peroxide in water with peroxidase-catalyzed oxidation of potassium iodide and its applications to hydroxylamine-involved Fenton and Fenton-like systems

A spectrophotometric method for the rapid measurement of hydrogen peroxide (H₂O₂) in aqueous solutions was developed in this study. This method is based on a reaction catalyzed by peroxidase (POD) in which potassium iodide (KI) is oxidized to generate the stable yellow-colored I₃^- within 15 s. The absorbance of the generated I₃^- at both 350 nm and 400 nm had good linear relationships with H₂O₂ concentration in the range of 0-70 μM (R² > 0.999) with sensitivities of 2.34 × 10⁴ M^-1 cm^-1 and 5.30 × 10³ M^-1 cm^-1 respectively. Meanwhile, through calculation, the detection limits of the proposed POD-KI method at 350 nm and 400 nm were 0.09 μM and 0.33 μM, respectively. Even when the concentration of H₂O₂ was up to 350 μM, the absorbance of the generated I₃^- at 350 nm did not decrease observably. The generated I₃^- was found to be stable enough in ultrapure water, underground water, reservoir water and samples containing the strong reducing agent hydroxylamine. Moreover, the proposed POD-KI method was successfully used to analyze trace H₂O₂ in rainwater, and to monitor the change of H₂O₂ concentration in the Fenton, hydroxylamine/Fenton and hydroxylamine/Cu(II)/H₂O₂ systems. Overall, the POD-KI method could be adopted as a candidate method to determine H₂O₂ in Fenton and Fenton-like systems, and especially in those involving hydroxylamine.

A spectrophotometric method for measuring permanganate index (CODMn) by N,N-diethyl-p-phenylenediamine (DPD)

A new spectrophotometric method for measuring permanganate index (chemical oxygen demand using potassium permanganate (KMnO₄) as oxidant, COD_Mn) in water was established. The method was based on the rapid oxidation of N,N-diethyl-p-phenylenediamine (DPD) by residual KMnO₄ in digestion solution under neutral pH condition to form the stable pink radical (DPD^●+). Only 20 s were enough to form the pink DPD^●+. The generated DPD^●+ could be quantitatively measured by a visible spectrophotometer at 551 nm. Stoichiometric coefficient of the reaction between KMnO₄ and DPD was close to 1:5 (1:5.07). There was a well linear relationship (R² = 0.999) between the change of the absorbance of DPD^●+ at 551 nm and the concentration of COD_Mn in the range of 0-4.46 mg L^-1. Limit of detection of the DPD method was as low as 0.02 mg L^-1 COD_Mn. The DPD method was highly accurate for measuring COD_Mn in standard solutions with well recovery rates of 99.17%-102.22%, and was well tolerant to the interference of coexistent Cl^- and Fe³⁺. The DPD method was successfully applied for measuring COD_Mn in real water samples, including surface water, underground water and drinking water. In comparison to the traditional titration method, the proposed DPD method was more convenient to operate, required less samples and digestion reagents (i.e., KMnO₄ and H₂SO₄) and could be employed for online monitor.

An overview of surface-enhanced Raman scattering substrates by pulsed laser deposition technique: fundamentals and applications

Metallic nanoparticles (NPs), as an efficient substrate for surface-enhanced Raman scattering (SERS), attract much interests because of their various shapes and sizes. The appropriate size and morphology of metallic NPs are critical to serve as the substrate for achieving an efficient SERS. Pulsed laser deposition (PLD) is one of the feasible physical methods employed to synthesize metallic NPs with controllable sizes and surface characteristics. It has been recognized to be a successful tool for the deposition of SERS substrates due to its good controllability and high reproducibility in the manufacture of metallic NPs. This review provides an overview about the recent advances for the preparation of SERS substrates by PLD technique. The influences of parameters on the sizes and morphologies of metallic NPs during the deposition processes in PLD technique including laser output parameters, gas medium, liquid medium, substrate temperature, and properties of 3D substrate are presented. The applications of SERS substrates produced by PLD in the environmental monitoring and biomedical analysis are summarized. This knowledge could serve as a guideline for the researchers in exploring further applications of PLD technique in the production of SERS substrate.

Nitrogen-doped carbon dot threads as a "turn-off" fluorescent probe for permanganate ions and its hydrogel hybrid as a naked eye sensor for gold(III) ions

Highly fluorescent nitrogen-doped carbon dot (NCD) threads were synthesized via simple pyrolysis of citric acid, p-hydroxybenzoic acid, and ammonia. The NCDs show excitation-independent behavior with maximum excitation and emission wavelengths of 350 nm and 435 nm, respectively. The developed probe was used as a turn-off fluorescent sensor for the selective and sensitive determination of permanganate ions in aqueous media. The probe's hydrogel hybrid displayed a beautiful purple color demonstrating its potential as a naked eye sensor for gold detection. The ratiometric sensor exhibited excellent selectivity towards permanganate ions over 27 other ions with a linear range of 510 nM to 2 μM, a detection limit of 170 nM, and a linear regression value (R²) of 0.9944. Similarly, the linear range and limit of detection for gold ions was 3.89-20 μM and 1.285 μM, respectively. The synthesized NCDs were also used as a fluorescent ink as well as a naked eye marker in association with a gold solution demonstrating its potential forensic and anti-counterfeiting applications. Graphical abstract.

Facile Preparation of Boron and Nitrogen Codoped Green Emission Carbon Quantum Dots for Detection of Permanganate and Captopril

A hydrothermal strategy for preparing boron and nitrogen codoped carbon quantum dots was studied using the precursors of p-amino salicylic acid, boric acid and ethylene glycol dimethacrylate. The boron and nitrogen codoped carbon quantum dots have high fluorescence intensity, good monodispersity, high stability, superior water solubility, and a fluorescence quantum yield of 19.6%. Their average size is 5 nm. Their maximum excitation and emission wavelengths are 380 and 520 nm, respectively. Permanganate (MnO₄^-) quenched boron and nitrogen codoped carbon quantum dots fluorescence through inner filter effect and static quenching effects. The linear relation between quenching efficiency and MnO₄^- concentration ranged from 0.05 to 60 μmol/L with a detection limit of 13 nmol/L. In the presence of captopril, MnO₄^- was reduced to Mn²⁺ and the fluorescence of boron and nitrogen codoped carbon quantum dots was recovered. The linear range between recovery and captopril concentration was from 0.1 to 60 μmol/L. The limit of detection was 0.03 μmol/L. The developed method can be employed as a sensitive fluorescence sensing platform for MnO₄^-. It has been successfully used for captopril detection in mouse plasma.

A novel coumarin-based fluorescent probe with fine selectivity and sensitivity for hypochlorite and its application in cell imaging

It is necessary to develop simple and highly sensitive methods for the detection of hypochlorous acid (HOCl)/hypochlorite (ClO^-) to ravel its relationship with disease. In this paper, a novel bio-compatible fluorescent (Z)-8-(hydrazonomethyl)-7-hydroxy-4-methyl-2H-chromen-2-one (probe 1b) based on coumarin was synthesized and used for detecting ClO^- in PBS buffer (pH = 7.2, 10 mM, 60% C₂H₅OH). Probe 1b showed a remarkable fluorescence change from yellow to blue with the limit of detection as low as 2.4 × 10^-9 M^-1 when ClO^- was added. The coexisted anions, metal ions and reactive oxygen species (•OH, ¹O₂, H₂O₂, KO₂) showed any competitiveness towards ClO^-. In response to ClO^-, the fluorescence emission intensity of probe 1b was obviously enhanced within 20 s. The mechanism was confirmed by the ESI - MS and density functional theory calculations (DFT) to reveal that the coumarin lactone bonds C - O was cleavaged by oxidation of ClO^-. What's more, probe 1b could be used in practical water samples and showed well recovery. Additionally, the cell imaging experiment was demonstrated that probe 1b could be effectively exploited to imaging exogenous ClO^- in vitro.

A fluorescent probe for sequential sensing of MnO4− and Cr2O72− ions in aqueous medium based on a UCNS/TMB nanosystem

Distinguishable and sequential detection of MnO₄⁻ and Cr₂O₇²⁻ was realized by the reactions above and IFE between UCNS and oxTMB.