Adsorptive removal of dye in wastewater by metal ferrite-enabled graphene oxide nanocomposites

Enhancing Zn (II) recovery efficiency: Bi-divalent nickel-cobalt ferrite spinel NiXCo1-xFe2O4 as a Game-changing Adsorbent-an experimental and computational study

This study presents a comprehensive investigation into NiXCo1-xFe2O4 (x = 0.5) spinel nanoparticles synthesized through a one-pot hydrothermal method using Co(NO3)2.6H2O and Ni(NO3)2.6H2O salts. XRD, FTIR, FESEM, and VSM analyses confirmed a cubic structure of NiXCo1-xFe2O4 (x = 0.5) nanoparticles without impurities. These nanoparticles exhibit efficient Zn (II) adsorption characteristics, following Langmuir isotherm and pseudo-second-order kinetics. The maximum adsorption capacity was measured to be 666.67 mg g-1 at pH = 7, with mechanisms involving both electrostatic attraction and cation exchange. Desorption studies indicate more than 75% Zn (II) recovery in an acidic environment (pH = 2) after three cycles. Computational analysis was used to validate the experimental results through Molecular Dynamics simulations, initially focusing on NiXCo1-xFe2O4 (x = 0.5). Further exploration involved variations in x at 0.25 and 0.75 to identify the optimal Ni and Co ratio in this bivalent cation spinel ferrite. Computational analyses reveal the superior performance of NiXCo1-xFe2O4 (x = 0.75) in Zn (II) removal, supported by radial distribution analysis, VdW energy, Coulombic energy, mean square displacement (MSD), root mean square displacement (RMSD), and interaction energy. This comprehensive study provides valuable insights into the adsorption behavior and structural stability of NiXCo1-xFe2O4 nanoparticles, showcasing potential applications in Zn (II) removal.

Design of silver-zinc-nickel spinel-ferrite mesoporous silica as a powerful and simply separable adsorbent for some textile dye removal

Silver-zinc-nickel spinel ferrite was prepared by the co-precipitation procedure with the precise composition Ag0.1Zn0.4Ni0.5Fe2O4 for bolstering pollutant removal effectiveness while upholding magnetic properties and then coated with a mesoporous silica layer. The surface characteristics and composition of Ag0.1Zn0.4Ni0.5Fe2O4@mSiO2 were confirmed using EDX, FT-IR, VSM, XRD, TEM, SEM, and BET methods. The surface modification of Ag-Zn-Ni ferrite with a silica layer improves the texture properties, where the specific surface area and average pore size of the spinel ferrite rose to 180 m2/g and 3.15 nm, respectively. The prepared spinel ferrite@mSiO2 has been utilized as an efficient adsorbent for eliminating methyl green (MG) and indigo carmine (IC) as models of cationic and anionic dyes from wastewater, respectively. Studying pH, Pzc, adsorbent dosage, dye concentration, and temperature showed that efficient removal of MG was carried out in alkaline media (pH = 12), while the acid medium (pH = 2) was effective for IC removal. Langmuir isotherm and pseudo-second-order kinetics were found to be good fits for the adsorption data. Both dyes were adsorbed in a spontaneous, endothermic process. A possible mechanism for dye removal has been proposed. The adsorbent was effectively recovered and reused.

An Updated Overview of Magnetic Composites for Water Decontamination

Water contamination by harmful organic and inorganic compounds seriously burdens human health and aquatic life. A series of conventional water purification methods can be employed, yet they come with certain disadvantages, including resulting sludge or solid waste, incomplete treatment process, and high costs. To overcome these limitations, attention has been drawn to nanotechnology for fabricating better-performing adsorbents for contaminant removal. In particular, magnetic nanostructures hold promise for water decontamination applications, benefiting from easy removal from aqueous solutions. In this respect, numerous researchers worldwide have reported incorporating magnetic particles into many composite materials. Therefore, this review aims to present the newest advancements in the field of magnetic composites for water decontamination, describing the appealing properties of a series of base materials and including the results of the most recent studies. In more detail, carbon-, polymer-, hydrogel-, aerogel-, silica-, clay-, biochar-, metal-organic framework-, and covalent organic framework-based magnetic composites are overviewed, which have displayed promising adsorption capacity for industrial pollutants.

A Sustainable and Regenerative Process for the Treatment of Textile Effluents Using Nonphotocatalytic Water Splitting by Nanoporous Oxygen-Deficient Ferrite

Water is crucial for life. Being the world's third-largest industry, the textile industry pollutes 93 billion cubic meters of water each year. Only 28% of textile wastewater is treated by lower- to middle-income countries due to the costly treatment methods. The present work demonstrates the utilization of surface oxygen defects and nanopores in Mg0.8Li0.2Fe2O4 (Li-MgF) to treat textile effluents by a highly economical, scalable, and eco-friendly process. Nanoporous, oxygen-deficient Li-MgF splits water by a nonphotocatalytic process at room temperature to produce green electricity as hydroelectric cell. The adsorbent Li-MgF can be easily regenerated by heat treatment. A 70-90% reduction in the UV absorption intensity of adsorbent-treated textile effluents was observed by UV-visible spectroscopy. The oxygen defects on Li-MgF surface and nanopores were confirmed by X-ray photoelectron spectroscopy and Brunauer-Emmett-Teller (BET) measurements, respectively. To analyze the adsorption mechanism, three known organic water-soluble dyes, brilliant green, crystal violet, and congo red, were treated with nanoporous Li-MgF. The dye decolorization efficiency of Li-MgF was recorded to be 99.84, 99.27, and 99.31% at 250 μM concentrations of brilliant green, congo red, and crystal violet, respectively. The results of Fourier transform infrared (FTIR) spectroscopy confirmed the presence of dyes on the material surface attached through hydroxyl groups generated by water splitting on the surface of the material. Total organic carbon analysis confirmed the removal of organic carbon from the dye solutions by 82.8, 77.0, and 46.5% for brilliant green, Congo red, and crystal violet, respectively. Based on the kinetic and isotherm models, the presence of a large number of surface hydroxyl groups on the surface of the material and OH- ions in solutions generated by water splitting was found to be responsible for the complete decolorization of all of the dyes. Adsorption of chemically diverse dyes by the nanoporous, eco-friendly, ferromagnetic, economic, and reusable Li-MgF provides a sustainable and easy way to treat textile industry effluents in large amounts.

Cellulose-alginate hydrogels and their nanocomposites for water remediation and biomedical applications

In the last decade, both cellulose and alginate polysaccharides have been extensively utilized for the synthesis of biocompatible hydrogels because of their alluring characteristics like low cost, biodegradability, hydrophilicity, biodegradability, ease of availability and non-toxicity. The presence of abundant hydrophilic functional groups (like carboxyl and hydroxyl) on the surface of cellulose and alginate or their derivatives makes these materials promising candidates for the preparation of hydrogels with appealing structures and characteristics, leading to growing research in water treatment and biomedical fields. These two polysaccharides are typically blended together to improve hydrogels' desired qualities (mechanical strength, adsorption properties, cellulose/alginate yield). So, keeping in view their extensive applicability, in the present review article, recent advances in the development of cellulose/nanocellulose-alginate-based hydrogels and their relevance in water treatment (adsorption of dyes, heavy metals, etc.) and biomedical field (wound healing, tissue engineering, drug delivery) has been reviewed. Further, impact of other inorganic/organic additives in cellulose/nanocellulose-alginate-based hydrogels properties like contaminants adsorption, drug delivery, tissue engineering, etc., has also been studied. Moreover, the current difficulties and future prospects of nanocellulose-alginate-based hydrogels regarding their water purification and biomedical applications are also discussed at the end.

Screening of Metal Oxides and Hydroxides for Arsenic Removal from Water Using Molecular Dynamics Simulations

Arsenic in groundwater is a harmful and hazardous substance that must be removed to protect human health and safety. Adsorption, particularly using metal oxides, is a cost-effective way to treat contaminated water. These metal oxides must be selected systematically to identify the best material and optimal operating conditions for the removal of arsenic from water. Experimental research has been the primary emphasis of prior work, which is time-consuming and costly. The previous simulation studies have been limited to specific adsorbents such as iron oxides. It is necessary to study other metal oxides to determine which ones are the most effective at removing arsenic from water. In this work, a molecular simulation computational framework using molecular dynamics and Monte Carlo simulations was developed to investigate the adsorption of arsenic using various potential metal oxides. The molecular structures have been optimized and proceeded with sorption calculations to observe the adsorption capabilities of metal oxides. In this study, 15 selected metal oxides were screened at a pressure of 100 kPa and a temperature of 298 K for As(V) in the form of HAsO4 at pH 7. Based on adsorption capacity calculations for selected metal oxides/hydroxides, aluminum hydroxide (Al(OH)3), ferric hydroxide (FeOOH), lanthanum hydroxide La(OH)3, and stannic oxide (SnO2) were the most effective adsorbents with adsorption capacities of 197, 73.6, 151, and 42.7 mg/g, respectively, suggesting that metal hydroxides are more effective in treating arsenic-contaminated water than metal oxides. The computational results were comparable with previously published literature with a percentage error of 1%. Additionally, SnO2, which is rather unconventional to be used in this application, demonstrates potential for arsenic removal and could be further explored. The effects of pH from 1 to 13, temperature from 281.15 to 331.15 K, and pressure from 100 to 350 kPa were studied. Results revealed that adsorption capacity decreased for the high-temperature applications while experiencing an increase in pressure-promoted adsorption. Furthermore, response surface methodology (RSM) has been employed to develop a regression model to describe the effect of operating variables on the adsorption capacity of screened adsorbents for arsenic removal. The RSM models utilizing CCD (central composite design) were developed for Al(OH)3, La(OH)3, and FeOOH, having R2 values 0.92, 0.67, and 0.95, respectively, suggesting that the models developed were correct.

Kinetic and equilibrium study of graphene and copper oxides modified nanocomposites for metal ions adsorption from binary metal aqueous solution

Presently, the main cause of pollution of natural water resources is heavy metal ions. The removal of metal ions such as nickel (Ni2+) and cadmium (Cd2+) has been given considerable attention due to their health and environmental risks. In this regard, for wastewater treatment containing heavy metal ions, graphene oxide (GO) nanocomposites with metal oxide nanoparticles (NPs) attained significant importance. In this study, graphene oxide stacked with copper oxide nanocomposites (GO/CuO-NCs) were synthesized and characterized by Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), and atomic force microscopy (AFM) analytical procedures. The prepared GO/CuO-NCs were applied for the removal of Ni2+ and Cd2+ ions from a binary metal ion system in batch and continuous experiments. The obtained results revealed that GO/CuO-NCs exhibited the highest removal efficiencies of Ni2+ (89.60% ± 2.12%) and Cd2+ (97.10% ± 1.91%) at the optimum values of pH: 8, dose: 0.25 g, contact time: 60 min, and at 50 ppm initial metal ion concentration in a batch study. However, 4 mL/min flow rate, 50 ppm initial concentration, and 2 cm bed height were proved to be the suitable conditions for metal ion adsorption in the column study. The kinetic adsorption data exhibited the best fitting with the pseudo-second-order model. The adsorption isotherm provided the best-fitting data in the Langmuir isotherm model. This study suggested that the GO/CuO nanocomposites have proved to be efficient adsorbents for Ni2+ and Cd2+ ions from a binary metal system.

Decoration of polylactic acid on graphene oxide for efficient adsorption of methylene blue and tetracycline

Decorating nanomaterials on graphene oxide (GO) can enhance its adsorption capacity and removal efficiency of water pollutants. In this study, for the first time, nano-sized polylactic acid (PLA) has been successfully decorated on the surface of GO through a facile synthesis approach. The adsorptive efficiency of GO-PLA for removing methylene blue (MB) and tetracycline (TC) from an aqueous solution was examined. The characterization confirmed the successful decoration of PLA on GO nanosheets with the nano size of PLA. It was hypothesized that the PLA was decorated on the surface of GO through covalent bonding between oxygen-containing functional groups and lactide molecules. The optimum adsorption parameters determined were at the adsorbent dose of 0.5 g L^-1, pH 4, contact time of 120 min, and temperature of 318 K. The pseudo-second-order kinetic model described the contaminants' adsorption behaviour, and the intraparticle diffusion model revealed that both surface adsorption and intraparticle diffusion controlled the adsorption process. Langmuir isotherm model best described the adsorption behaviour of the pollutants on GO-PLA and demonstrated the maximum monolayer uptake capacities of MB (332.5 mg g^-1) and TC (223.7 mg g^-1). The adsorption results indicated that the uptake capacities of GO-PLA in comparison to GO have increased by approximately 70% and 110% for MB and TC, respectively. These observations reflect the remarkable role of nano-sized PLA that enhanced the adsorption capacity due to its additional functional group and larger surface area.

Graphene-based materials for effective adsorption of organic and inorganic pollutants: A critical and comprehensive review

Water scarcity has been felt in many countries and will become a critical issue in the coming years. The release of toxic organic and inorganic contaminants from different anthropogenic activities, like mining, agriculture, industries, and domestic households, enters the natural waterbody and pollutes them. Keeping this in view in combating the environmental crises, removing pollutants from wastewater is one of the ongoing environmental challenges. Adsorption technology is an economical, fast, and efficient physicochemical method for removing both organic and inorganic pollutants, even at low concentrations. In the last decade, graphene and its composite materials have become the center of attraction for numerous applications, including wastewater treatment, due to the large surface area, highly active surface, and exclusive physicochemical properties, which make them potential adsorbents with unique physicochemical properties, like low density, chemical strength, structural variability, and the possibility of large-scale fabrications. This review article provides a thorough summary/critical appraisal of the published literature on graphene-, GO-, and rGO-based adsorbents for the removal of organic and inorganic pollutants from wastewater. The synthesis methods, experimental parameters, adsorption behaviors, isotherms, kinetics, thermodynamics, mechanisms, and the performance of the regeneration-desorption processes of these substances are scrutinized. Finally, the research challenges, limitations, and future research studies are also discussed. Certainly, this review article will benefit the research community by getting substantial information on suitable techniques for synthesizing such adsorbents and utilizing them in water treatment and designing water treatment systems.

Synthesis, Characterization and Dye Removal Capability of Conducting Polypyrrole/Mn0.8Zn0.2Fe2O4/Graphite Oxide Ternary Composites

Herein, ternary composites from polypyrrole (PPy), Mn0.8Zn0.2Fe2O4 (MZF), and graphite oxide (GO) were prepared to remove acid red dye (AR1) from wastewater. MZF was synthesized using spent Zn–C batteries, acid leaching, and sucrose auto-combustion processes; GO was prepared via oxidation and exfoliation of graphite. The composites were prepared by adding MZF and GO during the in-situ polymerization of pyrrole. Different PPy/MZF/GO (PMG) composites were prepared by changing the weight ratios of the PPy, MZF, and GO. We investigated the prepared composites’ structural, magnetic, and electrical/dielectric properties. We evaluated different experimental conditions’ influences on dye removal performance, such as pH, dosage, dye concentration, temperature, and contact time. XRD, FT-IR, and magnetic properties indicated that PPy completely coated the other contents. The electrical/dielectric properties improved while increasing the GO ratio. The PMG at GO content 50 wt.% (PMG50) showed the most efficient ratio for better removing AR1 from wastewater.

Synthesis of Functionalized Carboxylated Graphene Oxide for the Remediation of Pb and Cr Contaminated Water

With the growing scarcity of water, the remediation of water polluted with heavy metals is the need of hour. The present research work is aimed to address this problem by adsorbing heavy metals ions (Pb (II) and Cr (VI)) on modified graphene oxide having an excess of carboxylic acid groups. For this, graphene oxide (GO) was modified with chloroacetic acid to produce carboxylated graphene oxide (GO-COOH). The successful synthesis of graphene oxide and its modification has been confirmed using Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray Diffraction (XRD), Scanning electron microscopy (SEM), Energy Dispersive X-ray Analysis (EDX) and Transmission electron microscopy (TEM). The increase in surface area of graphene oxide after treatment with chloroacetic acid characterized by BET indicated its successful modification. A batch experiment was conducted to optimize the different factors affecting adsorption of both heavy metals on GO-COOH. After functionalization, we achieved maximum adsorption capacities of 588.23 mg g^-1 and 370.37 mg g^-1 for Pb and Cr, respectively, by GO-COOH which were high compared to the previously reported adsorbents of this kind. The Langmuir model (R² = 0.998) and Pseudo-second-order kinetic model (R² = 0.999) confirmed the monolayer adsorption of Pb and Cr on GO-COOH and the chemisorption as the dominant process governing adsorption mechanism. The present work shows that the carboxylation of GO can enhance its adsorption capacity efficiently and may be applicable for the treatment of wastewater.

Peroxymonosulfate activation by algal carbocatalyst for organic dye oxidation: Insights into experimental and theoretical

Preparation of nitrogen-doped algal carbocatalyst (NC) for peroxymonosulfate (PMS) activation to oxidative degrade methylene blue (MB), and the mechanism of radical and nonradical pathway in N-C/PMS system are investigated. Firstly, a series of N-doped carbonaceous materials (NC) were prepared using nitrogen-rich Taihu blue algae biomass as precursor at different annealing temperatures. It was found that the NC prepared by annealing at 800 °C (N-C-8) showed an optimal MB degradation performance of over 99% after 60 min. Confirmed by electron paramagnetic resonance (EPR) analyses and radical quenching experiments, radical and nonradical pathway (¹O₂ oxidation and electron-transfer) are both involved in MB degraded process. Moreover, both graphitic N derived from the intrinsic Taihu blue algae, and nitrogen vacancy evolved from nitrogen dopants decomposition exhibited high correlation with the MB removal rate in the N-C/PMS system. Finally, three possible degradation pathways of MB were proposed based on the Density Functional Theory (DFT) calculation and identified intermediates. Overall, this work provides a new insight into the intrinsic roles of nitrogen-dopants and nitrogen vacancies on the as-prepared carbocatalyst for PMS activation, and advances the understanding of the resource utilization of algal biomass.

Application of a polymer-magnetic-algae based nano-composite for the removal of methylene blue - Characterization, parametric and kinetic studies

The potential ability of synthesized PPy-Fe₃O₄-SW nano-composite to remove Methylene Blue (MB) from synthetic textile dye solution was investigated under batch conditions. Through parametric studies, the influence of process parameters namely solution pH, on the effective performance of nano-composite was studied. PPy - Fe₃O₄- SW nano-composite removed 99.14% of MB at the optimized conditions of pH-10, temperature - 25 °C, initial MB concentration - 50 mg/L, nano-composite dosage - 20 mg and contact time - 20 min. PPy - Fe₃O₄- SW nano-composite has a maximum sorption capacity of 666.66 mg/g. The kinetics and isotherm study revealed that the chromium adsorption obeys pseudo second order (PSO) model (R² = 0.9941) and Freundlich isotherm (R² = 0.9910) respectively. The PSO kinetic constant (K₂) was found to be 0.000442 (g/mg) min. The thermodynamic feasibility was confirmed through negative values of standard free energy at all tested conditions. The characteristics of adsorption study were analyzed and the results of FTIR, SEM and EDS confirmed the uptake of MB by PPy-Fe₃O₄-SW nano-composite.

Study on the Adsorption Performance of Casein/Graphene Oxide Aerogel for Methylene Blue

Casein (CS) and graphene oxide (GO) were employed for the fabrication of a casein/graphene oxide (CS/GO) aerogel by vacuum freeze drying. Fourier transform infrared spectroscopy, scanning electron microscopy, surface area and micropore analysis (BET), and thermogravimetric analysis were used to characterize the specific surface area, structure, thermal stability, and morphology of the CS/GO aerogel. The influence of experimental parameters such as the GO mass fraction in the aerogel, metering of the adsorbent, pH, contact time, and temperature on the adsorption capacity of the CS/GO aerogel on methylene blue (MB) was also investigated. According to Langmuir isotherm determination, the maximum removal rate of MB from the CS/GO aerogel was 437.29 mg/g when the temperature was 293 K and pH was 8. Through kinetic and thermodynamic studies, it is found that adsorption follows a pseudo-second-order reaction model and is also an exothermic and spontaneous process.

Tailored functional materials as robust candidates to mitigate pesticides in aqueous matrices-a review

Pesticides are among the top-priority contaminants, which significantly contribute to environmental deterioration. Conventional techniques are not efficient enough to remove pollutants from environmental matrices. The development of functional materials has emerged as promising candidates to remove and degrade pesticides and related hazardous compounds. Furthermore, the nanohybrid materials with unique structural and functional characteristics, such as better material anchorage, mass transfer, electron-hole separation, and charged interaction make them a versatile option to treat and reduce pollutants from aqueous matrices. Herein, we present the current progress in the development of functional materials for the abatement of toxic pesticides. The physicochemical characteristics and pesticide-removal functionalities of various metallic functional materials (e.g., zirconium, zinc, titanium, tungsten, and iron), polymer, and carbon-based materials are critically discussed with suitable examples. Finally, the industrial-scale applications of the functional materials, concluding remarks, and future directions in this important arena are given.