Optimization of coagulation and sedimentation conditions by turbidity measurement for nano- and microplastic removal

Self-Assembly of Three-Dimensional Hyperbranched Magnetic Composites and Application in High-Turbidity Water Treatment

In order to improve dispersibility, polymerization characteristics, chemical stability, and magnetic flocculation performance, magnetic Fe3O4 is often assembled with multifarious polymers to realize a functionalization process. Herein, a typical three-dimensional configuration of hyperbranched amino acid polymer (HAAP) was employed to assemble it with Fe3O4, in which we obtained three-dimensional hyperbranched magnetic amino acid composites (Fe3O4@HAAP). The characterization of the Fe3O4@HAAP composites was analyzed, for instance, their size, morphology, structure, configuration, chemical composition, charged characteristics, and magnetic properties. The magnetic flocculation of kaolin suspensions was conducted under different Fe3O4@HAAP dosages, pHs, and kaolin concentrations. The embedded assembly of HAAP with Fe3O4 was constructed by the N-O bond according to an X-ray photoelectron energy spectrum (XPS) analysis. The characteristic peaks of -OH (3420 cm-1), C=O (1728 cm-1), Fe-O (563 cm-1), and N-H (1622 cm-1) were observed in the Fourier transform infrared spectrometer (FTIR) spectra of Fe3O4@HAAP successfully. In a field emission scanning electron microscope (FE-SEM) observation, Fe3O4@HAAP exhibited a lotus-leaf-like morphological structure. A vibrating sample magnetometer (VSM) showed that Fe3O4@HAAP had a relatively low magnetization (Ms) and magnetic induction (Mr); nevertheless, the ferromagnetic Fe3O4@HAAP could also quickly respond to an external magnetic field. The isoelectric point of Fe3O4@HAAP was at 8.5. Fe3O4@HAAP could not only achieve a 98.5% removal efficiency of kaolin suspensions, but could also overcome the obstacles induced by high-concentration suspensions (4500 NTU), high pHs, and low fields. The results showed that the magnetic flocculation of kaolin with Fe3O4@HAAP was a rapid process with a 91.96% removal efficiency at 0.25 h. In an interaction energy analysis, both the UDLVO and UEDLVO showed electrostatic repulsion between the kaolin particles in the condition of a flocculation distance of <30 nm, and this changed to electrostatic attraction when the separation distance was >30 nm. As Fe3O4@ HAAP was employed, kaolin particles could cross the energy barrier more easily; thus, the fine flocs and particles were destabilized and aggregated further. Rapid magnetic separation was realized under the action of an external magnetic field.

Flow cytometry as a tool for the rapid enumeration of 1-μm microplastics spiked in wastewater and activated sludge after coagulation-flocculation-sedimentation

Considering the limited literature and the difficulty of quantifying 1-μm micro-nanoplastics (1-μm MNP) in complex aqueous matrices such as wastewater and sludge, the removal rate of these very small particles in wastewater treatment plants (WWTP) represents a major challenge. In this study, coagulation-flocculation-sedimentation (CFS) with aluminum salts was investigated to evaluate the removal of 1-μm MNPs spiked in tap water, raw wastewater, pre-settled wastewater, and activated sludge. Quantification of 1-μm MNP was performed using the high-throughput flow cytometry (FCM) analysis which takes only a few minutes and produces results with high accuracy and reproducibly. The results indicated that the 1-μm MNPs were highly stable in pure water and unable to settle rapidly. In raw wastewater, sedimentation without coagulants removed less than 4% of 1-μm MNP. Conversely, CFS treatment showed a significant improvement in the removal of 1-μm MNP from wastewater. At dosages of 0.3-3 mg Al3+/L, the removal of MNPs in wastewater reached 30% and no flocs were observed, while floc formation was visible with increased dosages of 3-12 mg Al3+/L, obtaining MNP removal greater than 90%. CFS in activated sludge with a solids content of 5800 mg MLSS/L registered the highest removal efficiency (95-99%) even for dosages of 0.3-60 mg Al3+/L and pH dropping to 5. However, activated sludge showed extremely high removal efficiency of MNPs (97.3 ± 0.9%) even without coagulants. The large, dense flocs that constitute activated sludge appear particularly efficient in capturing 1-μm MNPs during the sedimentation process even in the absence of coagulants.

Impact of natural organic matter and inorganic ions on the stabilization of polystyrene micro-particles

The orthokinetic coagulation of irregularly shaped polystyrene micro-particles (PS-MP) was investigated in solutions of inorganic cations with different valence (NaCl, CaCl2, LaCl3) using a coagulation jar test set-up combined with light extinction particle counting. The stabilizing effect of model natural organic matter (NOM from reverse-osmosis (RO-NOM), humic (HA) & fulvic acid (FA)) and of surface water components (SW-NOM) was studied. Collision efficiencies were calculated from the decrease in particle concentration applying first order reaction kinetics. The coagulation of PS-MP followed Derjaguin-Landau-Verwey-Overbeek (DLVO) theory with regard to ionic charge in solution. Highest collision efficiencies were obtained close to the suspected critical coagulation concentrations for CaCl2 (12 mM) and LaCl3 (5.5 mM) whereas for NaCl no CCC was found within the applied concentration range (10-1000 mM). The addition of NOM effectively stabilized PS-MP at low ionic strength (10 mM NaCl) in the order HA > RO-NOM > FA > SW-NOM at concentrations of dissolved organic carbon (DOC) as low as 0.2-0.5 mg/L DOC through electrostatic repulsion. PS-MP were effectively stabilized in 6.1 mg DOC/L of SW-NOM even at high ionic strength (100 mM MgCl2). Coagulation at intermediate ionic strength (10 mM MgCl2) was only observed for SW-NOM concentrations below 0.6 mg/L DOC. The results showed that even low NOM concentrations prevent PS-MP from orthokinetic coagulation in the presence of high ion concentrations. The study provides further insight in the orthokinetic coagulation behavior of PS-MP in the presence of NOM and highlights the importance of NOM for the stabilization of microplastics in aquatic suspensions. Further research is needed to elucidate the behavior of MP in turbulent systems to predict the mobility MP in aquatic systems such as rivers.

A powerful method for In Situ and rapid detection of trace nanoplastics in water-Mie scattering

The pervasive presence of nanoplastics (NPs) in environmental media has raised significant concerns regarding their implications for environmental safety and human health. However, owing to their tiny size and low level in the environment, there is still a lack of effective methods for measuring the amount of NPs. Leveraging the principles of Mie scattering, a novel approach for rapid in situ quantitative detection of small NPs in low concentrations in water has been developed. A limit of detection of 4.2 μg/L for in situ quantitative detection of polystyrene microspheres as small as 25 nm was achieved, and satisfactory recoveries and relative standard deviations were obtained. The results of three self-ground NPs showed that the method can quantitatively detect the concentration of NPs in a mixture of different particle sizes. The satisfactory recoveries (82.4% to 110.3%) of the self-ground NPs verified the good anti-interference ability of the method. The total concentrations of the NPs in the five brands of commercial bottled water were 0.07 to 0.39 μg/L, which were directly detected by the method. The proposed method presents a potential approach for conducting in situ and real-time environmental risk assessments of NPs on human and ecosystem health in actual water environments.

Recent advances in microplastic removal from drinking water by coagulation: Removal mechanisms and influencing factors

Microplastics (MPs) are emerging contaminants that are widely detected in drinking water and pose a potential risk to humans. Therefore, the MP removal from drinking water is a critical challenge. Recent studies have shown that MPs can be removed by coagulation. However, the coagulation removal of MPs from drinking water remains inadequately understood. Herein, the efficiency, mechanisms, and influencing factors of coagulation for removing MPs from drinking water are critically reviewed. First, the efficiency of MP removal by coagulation in drinking water treatment plants (DWTPs) and laboratories was comprehensively summarized, which indicated that coagulation plays an important role in MP removal from drinking water. The difference in removal effectiveness between the DWTPs and laboratory was mainly due to variations in treatment conditions and limitations of the detection techniques. Several dominant coagulation mechanisms for removing MPs and their research methods are thoroughly discussed. Charge neutralization is more relevant for small-sized MPs, whereas large-sized MPs are more dependent on adsorption bridging and sweeping. Furthermore, the factors influencing the efficiency of MP removal were jointly analyzed using meta-analysis and a random forest model. The meta-analysis was used to quantify the individual effects of each factor on coagulation removal efficiency by performing subgroup analysis. The random forest model quantified the relative importance of the influencing factors on removal efficiency, the results of which were ordered as follows: MPs shape > Coagulant type > Coagulant dosage > MPs concentration > MPs size > MPs type > pH. Finally, knowledge gaps and potential future directions are proposed. This review assists in the understanding of the coagulation removal of MPs, and provides novel insight into the challenges posed by MPs in drinking water.

Prolonged drying impedes the detachment of microplastics in unsaturated substrate: Role of flow regimes

The detachment of microplastics (MPs) from porous media under different moisture conditions and flow regimes has garnered limited attention within the research community. The present study investigates the detachment of MPs from porous media under wet and dry conditions combined with steady and transient flow. For both the wet and dry conditions, the increase in flow rates is found to decrease the detachment of hydrophobic polyethylene of two sizes and of hydrophilic polymethylmethacrylate. Intermittent flow is found to result in effluent peaks and a higher rate of MP detachment compared to steady flow. The ionic strength of inflow drops in a stepwise manner, leading to abrupt peaks followed by a tail corresponding to the arrival of each ionic strength front. Each step increase in flow rate leads to a steep peak followed by slow release over several pore volumes. Although transient flow facilitates the detachment of MPs, drying significantly impedes the detachment of MPs irrespective of flow regime. Ultraviolet weathering of MPs for 60 days weakens the inhibition effect of drying on hydrophilic polymethylmethacrylate, facilitating their detachment. Furthermore, the release of MPs decreases markedly with an increase in air-drying duration from 0 h to 72 h. Hydrus-1D two-site kinetic models are used to successfully simulate time-dependent processes, implying that drying heightens the energy barrier for MPs to detach. Our analysis confirms the significance of moisture in determining the remobilization of MPs, providing valuable insights concerning the fate of MPs in unsaturated substrate under prolonged drought conditions.

Application of advanced oxidation processes for the removal of micro/nanoplastics from water: A review

Micro/nanoplastics (MNPs) have been increasingly found in environments, food, and organisms, arousing wide public concerns. MNPs may enter food chains through water, posing a threat to human health. Therefore, efficient and environmentally friendly technologies are needed to remove MNPs from contaminated aqueous environments. Advanced oxidation processes (AOPs) produce a vast amount of active species, such as hydroxyl radicals (·OH), known for their strong oxidation capacity. As a result, an increasing number of researchers have focused on using AOPs to decompose and remove MNPs from water. This review summarizes the progress in researches on the removal of MNPs from water by AOPs, including ultraviolet photolysis, ozone oxidation, photocatalysis, Fenton oxidation, electrocatalysis, persulfate oxidation, and plasma oxidation, etc. The removal efficiencies of these AOPs for MNPs in water and the influencing factors are comprehensively analyzed, meanwhile, the oxidation mechanisms and reaction pathways are also discussed in detail. Most AOPs can achieve the degradation of MNPs, mainly manifest as the decrease of particle size and the increase of mass loss, but the mineralization rate is low, thus requiring further optimization for improved performance. Investigating various AOPs is crucial for achieving the complete decomposition of MNPs in water. AOPs will undoubtedly play a vital role in the future for the removal of MNPs from water.

Investigating the efficiency of oak powder as a new natural coagulant for eliminating polystyrene microplastics from aqueous solutions

Polystyrene (PS) is a commonly used plastic material in disposable containers. However, it readily breaks down into microplastic particles when exposed to water environments. In this research, oak powder was used as a natural, inexpensive, and eco-friendly coagulant. The present study aims to determine the effectiveness of oak powder in removing PS from aquatic environments. The Box-Behnken model (BBD) was used to determine the optimal conditions for removal. The removal efficiency was evaluated for various parameters including PS concentration (100-900 mg/L), pH (4-10), contact time (10-40 min), and oak dosage (100-400 mg/L). The maximum removal of PS microplastics (89.1%) was achieved by using an oak dose of 250 mg/L, a PS concentration of 900 mg/L, a contact time of 40 min, and a pH of 7. These results suggest that oak powder can effectively remove PS microplastics through surface adsorption and charge neutralization mechanisms, likely due to the presence of tannin compounds. Based on the results obtained, it has been found that the natural coagulant derived from oak has the potential to effectively compete with harmful chemical coagulants in removing microplastics from aqueous solutions.

Coagulation studies on photodegraded and photocatalytically degraded polystyrene microplastics using polyaluminium chloride

Microplastics are ubiquitous persistent emerging contaminants, and its presence has been detected even in the most pristine and fragile ecosystems. Advanced oxidation processes are one of the novel degradation technologies used for the elimination of microplastics from the environment. In this study, the effect of ultraviolet C (UV-C, 253.7 nm) and ultraviolet A (UV-A, 365 nm) irradiations on polystyrene (PS) microplastic properties in the presence and absence of titanium dioxide were studied along with their coagulation performances using polyaluminium chloride (PAC). The effects of solar irradiation on the chemical properties of microplastics in aqueous and dry conditions were also investigated. PS microplastics (1.5 g) in three size ranges, 300-150 μm, 150-75 μm, and <75 μm were used during this experiment. After 45 days of irradiation, samples showed discolouration, brittleness, and loss of hydrophobicity. Images obtained from scanning electron microscope revealed smoothening and melting of PS surfaces upon UV exposure. Attenuated total reflectance- Fourier transform infrared spectroscopy and X-ray photon spectroscopy of photoaged samples revealed chemical alterations, bond cleavage and formation of oxygenated functional groups on microplastic surfaces. PAC coagulation of samples before and after UV irradiation showed drastic differences in removal efficiencies, with UV-C irradiated microplastics exhibiting maximum efficiency. Large sized and photocatalytically degraded microplastics showed better removal efficiencies than small sized particles. The 300-150 μm sized PS microplastic, degraded photo catalytically under UV-C irradiation showed approximately 99 % removal efficiency, while PS < 75 μm photodegraded under UV-A irradiation showed only 74.2 % removal efficiency.

Release characteristics and toxicity assessment of micro/nanoplastics from food-grade nonwoven bags

Micro/nanoplastic (M/NP) contamination in food has become a global concern. Food-grade polypropylene (PP) nonwoven bags, which are widely used to filter food residues, are considered environmentally friendly and nontoxic. However, the emergence of M/NPs has forced us to re-examine the use of nonwoven bags in cooking as plastic contact with hot water leads to M/NP release. To evaluate the release characteristics of M/NPs, three food-grade PP nonwoven bags of different sizes were boiled in 500 mL water for 1 h. Micro-Fourier transform infrared spectroscopy and Raman spectrometer confirmed that the leachates were released from the nonwoven bags. After boiling once, a food-grade nonwoven bag can release 0.12-0.33 million MPs (>1 μm) and 17.6-30.6 billion NPs (<1 μm), equivalent to a mass of 2.25 - 6.47 mg. Number of M/NPs released is independent of nonwoven bag size; however, it decreases with increasing cooking times. M/NPs are primarily produced from easily breakable PP fibers, and they are not released into the water at once. Adult zebrafish (Danio rerio) were cultured in filtered distilled water without released M/NPs and in water containing 14.4 ± 0.8 mg L^-1 released M/NPs for 2 and 14 days, respectively. To evaluate the toxicity of the released M/NPs on the gills and liver of zebrafish, several oxidative stress biomarkers (i.e., reactive oxygen species, glutathione, superoxide dismutase, catalase, and malonaldehyde) were measured. The ingestion of the released M/NPs by zebrafish induces oxidative stress in the gills and liver, depending on the exposure time. Food-grade plastics, such as nonwoven bags, should be used with caution in daily cooking because they release large amounts of M/NPs when heated, which can threaten human health.

Tailoring Interactions of Random Copolymer Polyelectrolyte Complexes to Remove Nanoplastic Contaminants from Water

We investigate the usage of polyelectrolyte complex materials for water remediation purposes, specifically their ability to remove nanoplastics from water, on which there is currently little to no prior research. We demonstrate that oppositely charged random copolymers are effective at quantitatively removing nanoplastic contamination from aqueous solution. The mechanisms underlying this remediation ability are explored through computational simulations, with corroborating quartz crystal microbalance adsorption experiments. We find that hydrophobic nanostructures and interactions likely play an important role.

Chlorination disinfection by-products in Southeast Asia: A review on potential precursor, formation, toxicity assessment, and removal technologies

This review discusses disinfection by-products' (DBPs) potential precursors, formation, and toxicity, alongside available research on the treatment of DBPs in Southeast Asian countries' water sources. Although natural organic matter (NOM) in the form of humic and fulvic acids is the major precursor of DBPs formation, the presence of anthropogenic organic matter (AOM) also plays essential roles during disinfection using chlorine. NOM has been observed in water sources in Southeast Asian countries, with a relatively high concentration in peat-influenced water sources and a relatively low concentration in non-peat-influenced water sources. Similarly, AOMs, such as microplastics, pharmaceuticals, pesticides, and endocrine-disrupting chemicals (EDCs), have also been detected in water sources in Southeast Asian countries. Although studies regarding DBPs in Southeast Asian countries are available, they focus on regulated DBPs. Here, the formation potential of unregulated DBPs is also discussed. In addition, the toxicity associated with extreme DBPs' formation potential, as well as the effectiveness of treatments such as conventional coagulation, filtration, adsorption, and ozonation in reducing DBPs' formation potential in Southeast Asian sources of water, is also analyzed.