Low-dispersion electrokinetic flows for expanded separation channels in microfluidic systems:

Electrokinetic instability effects in microchannels with and without nanofilm coatings

This paper presents a parametric experimental investigation into the electrokinetic instability (EKI) phenomenon within three different types of microfluidic device, namely T-type, cross-shaped, and cross-form with an expansion configuration. The critical electric field strength at which the EKI phenomenon is induced is examined as a function of the conductivity ratio, the microchannel width, the expansion ratio, and the surface treatment of the microchannel walls. It is found that the critical electric field strength associated with the onset of EKI is strongly dependent on the conductivity ratio of the two samples within the microfluidic device and reduces as the channel width increases. The surfaces of the microchannel walls are coated with hydrophilic or hydrophobic organic-based spin-on-glass (SOG) nanofilms for glass-based microchips. The experimental results indicate that no significant difference exists in the critical electric field strengths in the hydrophilic or hydrophobic SOG-coated microchannels, respectively. However, for a given conductivity ratio and microchannel width, the critical strength of the electric field is slightly lower in the SOG-coated microchannels than in the non-coated channels. In general, the results presented in this study demonstrate the potential for designing and controlling on-chip assays requiring the manipulation of samples with high conductivity gradients, and provide a useful general reference for avoiding EKI effects in capillary electrophoresis analysis applications.

High performance microfluidic capillary electrophoresis devices

This paper presents a novel microfluidic capillary electrophoresis (CE) device featuring a double-T-form injection system and an expansion chamber located at the inlet of the separation channel. This study addresses the principal material transport mechanisms depending on parameters such as the expansion ratio, the expansion length, the fluid flow. Its design utilizes a double-L injection technique and combines the expansion chamber to minimize the sample leakage effect and to deliver a high-quality sample plug into the separation channel so that the detection performance of the device is enhanced. Experimental and numerical testing of the proposed microfluidic device that integrates an expansion chamber located at the inlet of the separation channel confirms its ability to increase the separation efficiency by improving the sample plug shape and orientation. The novel microfluidic capillary electrophoresis device presented in this paper has demonstrated a sound potential for future use in high-quality, high-throughput chemical analysis applications and throughout the micro-total-analysis systems field.

Dielectrophoretic manipulation of particles and cells using insulating ridges in faceted prism microchannels

This paper presents a novel device for the dielectrophoretic manipulation of particles and cells. A two-level isotropic etch of a glass substrate was used to create three-dimensional ridge-like structures in micrometer-sized channels. Due to the insulating properties of glass, locally patterned regions of nonuniform electric field form near the ridges when a dc field is applied along the channel. The ridges are designed using the method of faceted prisms, such that substantially uniform fields are produced on each side of the faceted interfaces that form each ridge. The dielectrophoretic force that results from the electric field gradient near the ridges is used to affect particle motion parallel to the ridges in the absence of a bulk pressure-driven flow. Trapping and deflection of particles and continuous concentration and separation of Bacillus subtilis from a two-component sample mixture are demonstrated. The flow of B. subtilis is restricted to a selected channel of a planar, multichannel device as a result of negative dielectrophoresis arising from the presence of the insulating ridges when the applied electric field exceeds a threshold of 30 V/mm. Dielectrophoresis has a negligible impact on 200-nm-diameter polystyrene particles under the same conditions.

Optimal configuration of capillary electrophoresis microchip with expansion chamber in separation channel

This study develops a novel capillary electrophoresis (CE) microfluidic device featuring a conventional cross-form injection system and an expansion chamber located at the inlet of the separation channel. The combined injection system/expansion chamber arrangement is designed to deliver a high-quality sample band into the separation channel such that the detection performance of the device is enhanced. Numerical simulations are performed to investigate the electrokinetic transport processes in the microfluidic device and to establish the optimal configuration of the expansion chamber. The results indicate that an expansion chamber with an expansion ratio of 2.5 and an expansion length of 500 microm delivers a sample plug with the correct shape and orientation. With this particular configuration, the peak intensities of the sample are sharp and clearly distinguishable in the detection region of the separation channel. Therefore, this configuration is well suited for capillary electrophoresis applications which require a highly sensitive resolution of the sample plug. The novel CE microfluidic device developed in this study has an exciting potential for use in high-performance, high-throughput chemical analysis applications and in many other applications throughout the field of micro-total-analysis-systems.

Fabrication and Analysis of Spatially Uniform Field Electrokinetic Flow Devices: Theory and Experiment

A uniform-field design approach can improve the performance of microanalytical, chip-based devices for a number of applications, including separations and sample preparation. The faceted prism paradigm allows the design of microfluidic devices possessing spatially uniform fields in electrokinetically driven flows. We present the first quantitative study of the velocity fields obtained using faceted interfaces between deep and shallow channel sections. Electrokinetic flows were generated in a series of wet-etch fabricated microfluidic channels. The resulting velocity fields were analyzed by particle image velocimetry and compared with simulations of the two-dimensional Laplace equation using both the designed channel geometry and the as-fabricated channel geometry. This analysis found localized differences between the designed and observed flow fields that were directly attributable to the limitations of isotropic substrate etching. Simulations using the as-fabricated channel geometry reproduced the experimental electrokinetic velocity field, quantitatively accounting for speed field variations due to the limits of the fabrication method. The electrokinetic speed fields were also compared to corresponding pressure-driven speed fields.