Determination of pesticides in soil by liquid-phase microextraction and gas chromatography–mass spectrometry

Integrated sample desalting, enrichment, and ionization on an omniphobic glass slide for direct mass spectrometry analysis

RATIONALE

Direct and rapid mass spectrometry (MS) analysis is desired for many applications including environmental monitoring, forensic analysis, chemical and biological defense, and point-of-care testing. However, sample pretreatment is often necessary for analyzing targets from complex matrices using MS due to ion suppression. To achieve rapid MS analysis calls for simple and efficient solutions for sample processing and ionization. Here, a simple sample pretreatment and ionization workflow is reported, which achieves sample desalting, enrichment, and ionization on a single glass slide.

METHODS

Desalting is achieved based on crystallization and re-dissolution-induced spontaneous separation of analytes and salt. Efficient sample enrichment is achieved during the crystallization process by modifying the glass surface with an omniphobic coating. Finally, vibrating sharp-edge spray ionization is employed to ionize the target molecules directly on the glass slide. Thus, all the necessary sample operations prior to MS analysis are completed on the sample glass slide.

RESULTS

Efficient sample enrichment on the omniphobic glass slide is first visualized using food dyes. The benefits of the desalting and enrichment steps for detecting macrolide antibiotics in 1× phosphate buffered saline (PBS) solutions are demonstrated by comparing samples with different treatment procedures. Finally, quantification of macrolide antibiotics from PBS and serum samples is demonstrated. A linear range between 2 nM and 10 μM has been achieved for the serum sample with a limit of detection of 1 nM.

CONCLUSIONS

A simple, flexible, low-cost, and highly integrated workflow for detecting target molecules from complex matrices using MS is demonstrated. This method will be valuable to many applications that require rapid and efficient MS analysis of complex samples.

Novel semi-automated graphene nanosheets based pipette-tip assisted micro-solid phase extraction as eco-friendly technique for the rapid detection of emerging environmental pollutant in waters

In this work, a new semi-automated syringe infusion-pump assisted graphene nanosheets (GNSs) based pipette-tip micro-solid phase extraction (PT-μSPE) as a green sample preparation technique was demonstrated for the sensitive analysis of emerging environmental pollutant in environmental waters using HPLC-UV. Microwave-assisted synthesized GNSs powder was packed into a 100 μL pipette-tip (as PT-μSPE cartridge) connected with a commercial plastic syringe (contains water sample). This setup was attached to a programmable auto-syringe infusion pump for the GNSs-PT-μSPE process. Triclosan (TCS) is an emerging environmental pollutant chosen as a target analyte to examine the extraction capacity and feasibility of GNSs as a sorbent material for PT-μSPE. Parameters affecting the extraction capability were systematically evaluated and thoroughly optimized. At optimized experimental parameters, excellent linearity (r² = 0.9979) was achieved over the concentration range of 2-250 ng mL^-1 for TCS, with a detection limit of 0.5 ng mL^-1. Applicability of the presented method was examined with real water samples, and extraction recoveries obtained were ranged between 94.6-102.4% with RSD less than 7.8%. The presented protocol is a simple, semi-automated, eco-friendly, low-cost, and efficient sample pretreatment technique for quick analysis of TCS in environmental wastewaters.

New Trend in the Extraction of Pesticides from the Environmental and Food Samples Applying Microextraction Based Green Chemistry Scenario: A Review

This review focused on the green microextraction methods used for the extraction of pesticides from the environmental and food samples. Microextraction techniques have been explored and applied in various fields of analytical chemistry since its beginning, as evinced by the numerous reviews published. The success of any technique in science and technology is measured by the simplicity, environmentally friendly, and its applications; and the microextraction technique is highly successive. Deliberations were attentive to studies where efforts have been made to validate the methods through the inter-laboratory comparison study to assess the analytical performance of microextraction techniques against conventional methods. Succinctly, developed microextraction methods are shown to impart significant benefits over conventional techniques. Provided that the analytical community continues to put forward attention and resources into the growth and validation of the microextraction technique, a promising future for microextraction is forecasted.

Multi-residue analysis of pesticides in blood plasma using hollow fiber solvent bar microextraction and gas chromatography with a flame ionization detector

The challenges faced on pesticide extraction from biological samples are finding a method that allows a multi-residue extraction, pre-concentration, clean-up, and isolation of analytes in just one step. In this sense, the hollow fiber - liquid phase microextraction method (HF- LPME) in the "solvent bar" mode was used to optimize and validate a method for pesticide multi-residue analysis in blood plasma at trace levels, through gas chromatography coupled with a flame ionization detector (GC-FID). Hollow fiber solvent bar microextraction HF-SBME was carried out with octanol immobilized into the pores of hydrophobic polypropylene fiber and disposed within a matrix of blood plasma, spiked with a mixture of pesticides (monocrotophos, lindane, aldrin, methyl parathion, endosulfan, dieldrin, DDD, DDT, and endrin). The optimization parameters evaluated were: extraction temperature and time, stirring speed, and salt concentration. A principal component analysis was performed to visualize the analytes' behaviour based on their explained variance, and then, a Box-Behnken analysis was generated to identify the optimum parameters. According to the PCA, all pesticides showed similar responses to the extraction method and the response of dieldrin exhibit the lowest variance. Moreover, the stationary points selected from the Box-Behnken analysis were 25.5 °C for the extraction temperature, 870 rpm for stirring speed, 16 min for extraction time, and 8.3 % w/v of salt concentration. Moreover, the validation results proved that HF-SBME is an alternative technique for pesticide multi-residue extraction in blood plasma. The analytes were able to concentrate, reaching 46 fold enrichment. The solvent type, sample and solvent volume were narrowed down without changing the method's precision or accuracy. The relative standard deviation was under 10 %, and the recovery was between 55 % and 105 % for the different analytes excepting lindane, which had lower recovery (27 %). The detection limits were 0.02 until 0.13 μg mL^-1 for most of the pesticides used. Finally, HF-SBME is a good alternative for pesticide multi-residue extraction in complex matrices like plasma.

Liquid phase microextraction techniques combined with chromatography analysis: a review

Sample pretreatment is the first and the most important step of an analytical procedure. In routine analysis, liquid–liquid microextraction (LLE) is the most widely used sample pre-treatment technique, whose goal is to isolate the target analytes, provide enrichment, with cleanup to lower the chemical noise, and enhance the signal. The use of extensive volumes of hazardous organic solvents and production of large amounts of waste make LLE procedures unsuitable for modern, highly automated laboratories, expensive, and environmentally unfriendly. In the past two decades, liquid-phase microextraction (LPME) was introduced to overcome these drawbacks. Thanks to the need of only a few microliters of extraction solvent, LPME techniques have been widely adopted by the scientific community. The aim of this review is to report on the state-of-the-art LPME techniques used in gas and liquid chromatography. Attention was paid to the classification of the LPME operating modes, to the historical contextualization of LPME applications, and to the advantages of microextraction in methods respecting the value of green analytical chemistry. Technical aspects such as description of methodology selected in method development for routine use, specific variants of LPME developed for complex matrices, derivatization, and enrichment techniques are also discussed.

Preparation of a new three-component deep eutectic solvent and its use as an extraction solvent in dispersive liquid-liquid microextraction of pesticides in green tea and herbal distillates

BACKGROUND

A new solvent, deep eutectic solvent, in which there is growing interest, has been prepared and used as an extraction solvent in the dispersive liquid-liquid method of microextraction. To prepare the solvent, dichloroacetic acid, l-menthol, and n-butanol are mixed at a molar ratio of 4:1:1 and the deep eutectic solvent is formed after heating. Then a dispersive liquid-liquid microextraction method using the prepared solvent is used for the extraction and preconcentration of some pesticides from an aqueous sample. To carry out the procedure, the deep eutectic solvent is mixed with methanol and rapidly injected by a syringe into the aqueous sample containing the analytes. After centrifuging, an aliquot of the sedimented phase is injected into the gas chromatograph. The influence of several variables on the extraction efficiency was investigated and optimized.

RESULTS

Extraction recoveries and enrichment factors were obtained in the ranges of 53-86% and 1760-2853, respectively. The intra- (n = 6) and inter-day (n = 5) precision of the method was satisfactory, with relative standard deviations ≤ 7% obtained at two concentrations of 10 and 50 μg L^-1 of each analyte. Moreover, detection and quantification limits for the target analytes were obtained in the ranges of 0.11-0.23 and 0.38-0.74 μg L^-1 , respectively.

CONCLUSION

Different samples, including green tea, rose water, lemon balm, mint, and pussy willow distillates were analyzed successfully using the method that was developed, and chlorpyrifos was found in rose water at a concentration of 17 ± 1 μg L^-1 (n = 3). © 2019 Society of Chemical Industry.

Recent Trends in the Development of Green Microextraction Techniques for the Determination of Hazardous Organic Compounds in Wine

Background:

The sample preparation is the most crucial step in the analytical method development. Taking this into account, it is easily understood why the domain of sample preparation prior to detection is rapidly developing. Following the modern trends towards the automation, miniaturization, simplification and minimization of organic solvents and sample volumes, green microextraction techniques witness rapid growth in the field of food quality and safety. In a globalized market, it is essential to face the consumers need and develop analytical methods that guarantee the quality of food products and beverages. The strive for the accurate determination of organic hazards in a famous and appreciated alcoholic beverage like wine has necessitated the development of microextraction techniques.

Objective:

The objective of this review is to summarize all the recent microextraction methodologies, including solid phase extraction (SPE), solid phase microextraction (SPME), liquid-phase microextraction (LPME), dispersive liquid-liquid microextraction (DLLME), stir bar sorptive extraction (SBSE), matrix solid-phase dispersion (MSPD), single-drop microextraction (SDME) and dispersive solid phase extraction (DSPE) that were developed for the determination of hazardous organic compounds (pesticides, mycotoxins, colorants, biogenic amines, off-flavors) in wine. The analytical performance of the techniques is evaluated and their advantages and limitations are discussed.

Conclusion:

An extensive investigation of these techniques remains vital through the development of novel strategies and the implication of new materials that could upgrade the selectivity for the extraction of target analytes.

Quantitative Determination of Thiabendazole in Soil Extracts by Surface-Enhanced Raman Spectroscopy

Thiabendazole (TBZ) is widely used in sclerotium blight, downy mildew as well as root rot disease prevention and treatment in plant. The indiscriminate use of TBZ causes the excess pesticide residues in soil, which leads to soil hardening and environmental pollution. Therefore, it is important to accurately monitor whether the TBZ residue in soil exceeds the standard. For this study, density functional theory (DFT) was used to theoretically analyze the molecular structure of TBZ, gold nanoparticles (AuNPs) were used to enhance the detection signal of surface-enhanced Raman spectroscopy (SERS) and the TBZ residue in red soil extracts was quantitatively determined by SERS. As a result, the theoretical Raman peaks of TBZ calculated by DFT were basically consistent with the measured results. Moreover, 784, 1008, 1270, 1328, 1406 and 1576 cm^-1 could be determined as the TBZ characteristic peaks in soil and the limits of detection (LOD) could reach 0.1 mg/L. Also, there was a good linear correlation between the intensity of Raman peaks and TBZ concentration in soil (784 cm^-1: y = 672.26x + 5748.4, R² = 0.9948; 1008 cm^-1: y = 1155.4x + 8740.2, R² = 0.9938) and the limit of quantification (LOQ) of these two linear models can reach 1 mg/L. The relative standard deviation (RSD) ranged from 1.36% to 8.02% and the recovery was ranging from 95.90% to 116.65%. In addition, the 300⁻1700 cm^-1 SERS of TBZ were analyzed by the partial least squares (PLS) and backward interval partial least squares (biPLS). Also, the prediction accuracy of TBZ in soil (R_p² = 0.9769, RMSE_P = 0.556 mg/L, RPD = 5.97) was the highest when the original spectra were pretreated by standard normal variation (SNV) and then modeled by PLS. In summary, the TBZ in red soil extracts could be quantitatively determined by SERS based on AuNPs, which was beneficial to provide a new, rapid and accurate scheme for the detection of pesticide residues in soil.

Solid phase microextraction of diclofenac using molecularly imprinted polymer sorbent in hollow fiber combined with fiber optic-linear array spectrophotometry

A simple solid phase microextraction method based on molecularly imprinted polymer sorbent in the hollow fiber (MIP-HF-SPME) combined with fiber optic-linear array spectrophotometer has been applied for the extraction and determination of diclofenac in environmental and biological samples. The effects of different parameters such as pH, times of extraction, type and volume of the organic solvent, stirring rate and donor phase volume on the extraction efficiency of the diclofenac were investigated and optimized. Under the optimal conditions, the calibration graph was linear (r(2)=0.998) in the range of 3.0-85.0 μg L(-1) with a detection limit of 0.7 μg L(-1) for preconcentration of 25.0 mL of the sample and the relative standard deviation (n=6) less than 5%. This method was applied successfully for the extraction and determination of diclofenac in different matrices (water, urine and plasma) and accuracy was examined through the recovery experiments.

Extraction and GC-MS analysis of phthalate esters in food matrices: a review

According to the Scopus database, using “phthalate” and “GC” as keywords, 758 papers have been found between 1990 and 2014, showing strong and increasing interest in this class of compounds from the scientific community.

Pseudo-stir bar hollow fiber solid/liquid phase microextraction combined with anodic stripping voltammetry for determination of lead and cadmium in water samples

A new procedure is presented for the determination of low concentrations of lead and cadmium in water samples. Ligand assisted pseudo-stir bar hollow fiber solid/liquid phase microextraction using sol-gel sorbent reinforced with carbon nanotubes was combined with differential pulse anodic stripping voltammetry for simultaneous determination of cadmium and lead in tap water, and Darongar river water samples. In the present work, differential pulse anodic stripping voltammetry (DPASV) using a hanging mercury drop electrode (HMDE) was used in order to determine the ultra trace level of lead and cadmium ions in real samples. This method is based on accumulation of lead and cadmium ions on the electrode using different ligands; Quinolin-8-ol, 5,7-diiodo quinoline-8-ol, 4,5-diphenyl-1H-imidazole-2(3H)-one and 2-{[2-(2-Hydroxy-ethylamino)-ethylamino]-methyl}-phenol as the complexing agent. The optimized conditions were obtained. The relationship between the peak current versus concentration was linear over the range of 0.05-500 ng mL(-1) for Cd (II) and Pb (II). The limits of detection for lead and cadmium were 0.015 ng mL(-1) and 0.012 ng mL(-1), respectively. Under the optimized conditions, the pre-concentration factors are 2440 and 3710 for Cd (II) and Pb (II) in 5 mL of water sample, respectively.

Applications of liquid-phase microextraction in the sample preparation of environmental solid samples

Solvent extraction remains one of the fundamental sample preparation techniques in the analysis of environmental solid samples, but organic solvents are toxic and environmentally harmful, therefore one of the possible greening directions is its miniaturization. The present review covers the relevant research from the field of application of microextraction to the sample preparation of environmental solid samples (soil, sediments, sewage sludge, dust etc.) published in the last decade. Several innovative liquid-phase microextraction (LPME) techniques that have emerged recently have also been applied as an aid in sample preparation of these samples: single-drop microextraction (SDME), hollow fiber-liquid phase microextraction (HF-LPME), dispersive liquid-liquid microextraction (DLLME). Besides the common organic solvents, surfactants and ionic liquids are also used. However, these techniques have to be combined with another technique to release the analytes from the solid sample into an aqueous solution. In the present review, the published methods were categorized into three groups: LPME in combination with a conventional solvent extraction; LPME in combination with an environmentally friendly extraction; LPME without previous extraction. The applicability of these approaches to the sample preparation for the determination of pollutants in solid environmental samples is discussed, with emphasis on their strengths, weak points and environmental impact.

Extraction of ultra traces of polychlorinated biphenyls in aqueous samples using suspended liquid-phase microextraction and gas chromatography-electron capture detection

This study reports the feasibility of applying directly suspended liquid-phase microextraction (DSLPME)-gas chromatography detection for the pre-concentration and determination of low levels of eight polychlorinated biphenyls (PCBs) in aqueous samples. The technique requires minimal sample preparation, analysis time and solvent consumption and represents significant advantages over conventional analytical methods. The experimental parameters such as salt content, sample temperature, stirring rate, extraction time, micro-drop volume and breakthrough volume were investigated and found to have significant influences on DSLPME. Under the optimal experimental conditions, the enrichment factor ranged from 578 to 729, and the recovery was above 93 %. Calibration curves possessed good linearity (R(2) > 0.99) over a wide concentration range of 0.1-10.0 μg L(-1) with limits of detection ranging from 0.01 to 0.07 μg L(-1). The relative standard deviations for 1.0 μg L(-1) of PCBs in water by using internal standard were in the range 2-14 % (n = 3). The proposed simple, accurate and sensitive analytical method was applied successfully to the determination of trace amounts of PCBs in water samples.

Considerations on the application of miniaturized sample preparation approaches for the analysis of organic compounds in environmental matrices

The miniaturization and improvement of sample preparation is a challenge that has been fulfilled up to a point in many fields of analytical chemistry. Particularly, the hyphenation of microextraction with advanced analytical techniques has allowed the monitoring of target analytes in a vast variety of environmental samples. Several benefits can be obtained when miniaturized techniques such as solid-phase microextraction (SPME) or liquid-phase microextraction (LPME) are applied, specifically, their easiness, rapidity and capability to separate and pre-concentrate target analytes with a negligible consumption of organic solvents. In spite of the great acceptance that these green sample preparation techniques have in environmental research, their full implementation has not been achieved or even attempted in some relevant environmental matrices. In this work, a critical review of the applications of LPME and SPME techniques to isolate and pre-concentrate traces of organic pollutants is provided. In addition, the influence of the environmental matrix on the effectiveness of LPME and SPME for isolating the target organic pollutants is addressed. Finally, unsolved issues that may hinder the application of these techniques for the extraction of dissolved organic matter from environmental samples and some suggestions for developing novel and less selective enrichment and isolation procedures for natural organic matter on the basis of SPME and LPME are included.

An overview of sample preparation and extraction of synthetic pyrethroids from water, sediment and soil

The latest developments in sample preparation and extraction of synthetic pyrethroids from environmental matrices viz., water, sediment and soil were reviewed. Though the synthetic pyrethroids were launched in 1970s, to the best of authors' knowledge there was no review on this subject until date. The present status and recent advances made during the last 10 years in sample preparation including conservation and extraction techniques used in determination of synthetic pyrethroids in water, sediment and soil were discussed. Pre- and post-extraction treatments, sample stability during extraction and its influence upon the whole process of analytical determination were covered. Relative merits and demerits including the green aspects of extraction were evaluated. The current trends and future prospects were also addressed.

Development of miniaturized hollow-fiber assisted liquid-phase microextraction with in situ acyl derivatization followed by GC-MS for the determination of benzophenones in human urine samples

A simple and highly sensitive method that involves miniaturized hollow fiber assisted liquid-phase microextraction (HF-LPME) with in situ acyl derivatization and GC-MS was developed for the determination of benzophenone (BP) and related compounds in human urine samples. The limits of detection (S/N = 3) and quantification (S/N > 10) of BPs in human urine samples are 0.01 to 0.05 and 0.05 to 0.2 ng ml(-1), respectively. The average recoveries of BPs (n = 5) in human urine samples spiked with 10 and 50 ng ml(-1) BPs are 93.1 to 106.7% (RSD: 1.5 to 8.4%) and 96.3 to 101.5% (RSD: 3.0 to 7.7%), respectively. When the proposed method was applied to human urine samples, BPs were detected at the sub ng ml(-1) level.