Plastic microchip liquid chromatography-matrix-assisted laser desorption/ionization mass spectrometry using monolithic columns

Interfacing microfluidics with information-rich detection systems for cells, bioparticles, and molecules

The development of elegant and numerous microfluidic manipulations has enabled significant advances in the processing of small volume samples and the detection of minute amounts of biomaterials. Effective isolation of single cells in a defined volume as well as manipulations of complex bioparticle or biomolecule mixtures allows for the utilization of information-rich detection methods including mass spectrometry, electron microscopy imaging, and amplification/sequencing. The art and science of translating biosamples from microfluidic platforms to highly advanced, information-rich detection system is the focus of this review, where we term the translation between the microfluidics elements to the external world “off-chipping.” When presented with the challenge of presenting sub-nanoliter volumes of manipulated sample to a detection scheme, several delivery techniques have been developed for effective analysis. These techniques include spraying (electrospray, nano-electrospray, pneumatic), meniscus-defined volumes (droplets, plugs), constrained volumes (narrow channels, containers), and phase changes (deposition, freezing). Each technique has been proven effective in delivering highly defined samples from microfluidic systems to the detection elements. This review organizes and presents selective publications that illustrate the advancements of these delivery techniques with respect to the type of sample analyzed, while introducing each strategy and providing historical perspective. The publications highlighted in this review were chosen due to their significance and relevance in the development of their respective off-chip technique.

Design of pH-Responsive Polymer Monolith Based on Cyclodextrin Vesicle for Capture and Release of Myoglobin

β-Cyclodextrin vesicles (CDVs) were first introduced into the polymer monolith to prepare a pH-responsive adsorption material and used for capture and release of a cardiac biomarker, myoglobin (Myo). SH-CDV was decorated with adamantane-modified SH-octapeptide to enhance the encapsulation and release rates of Myo. Afterward, SH-CDV was introduced into the polymer monolith via click reaction to produce a pH-responsive monolith. Combining with the mass spectrometry detection, the CDV-based pH-responsive monolith was used for the enrichment of Myo glycopeptides from the mixture of glycopeptides and nonglycoprotein (bovine serum albumin) tryptsin digests reach up to 1:10 000. A limit of detection of 0.1 fmol was obtained for Myo glycopeptides in the blood sample, indicating the high sensitivity of the method. The prepared CDV-based hybrid monolith demonstrated itself to be a promising material for capture of glycoproteins in complex samples, which provides an efficient strategy for the identification and discovery of biomarkers of acute myocardial infarction.

Prototyping of thermoplastic microfluidic chips and their application in high-performance liquid chromatography separations of small molecules

The present paper discusses practical aspects of prototyping of microfluidic chips using cyclic olefin copolymer as substrate and the application in high-performance liquid chromatography. The developed chips feature a 60mm long straight separation channel with circular cross section (500μm i.d.) that was created using a micromilling robot. To irreversibly seal the top and bottom chip substrates, a solvent-vapor-assisted bonding approach was optimized, allowing to approximate the ideal circular channel geometry. Four different approaches to establish the micro-to-macro interface were pursued. The average burst pressure of the microfluidic chips in combination with an encasing holder was established at 38MPa and the maximum burst pressure was 47MPa, which is believed to be the highest ever report for these polymer-based microfluidic chips. Porous polymer monolithic frits were synthesized in-situ via UV-initiated polymerization and their locations were spatially controlled by the application of a photomask. Next, high-pressure slurry packing was performed to introduce 3μm silica reversed-phase particles as the stationary phase in the separation channel. Finally, the application of the chip technology is demonstrated for the separation of alkyl phenones in gradient mode yielding baseline peak widths of 6s by applying a steep gradient of 1.8min at a flow rate of 10μL/min.

A simple and low-cost chip bonding solution for high pressure, high temperature and biological applications

The sealing of microfluidic devices remains a complex and time-consuming process requiring specific equipment and protocols: a universal method is thus highly desirable. We propose here the use of a commercially available sealing tape as a robust, versatile, reversible solution, compatible with cell and molecular biology protocols, and requiring only the application of manually achievable pressures. The performance of the seal was tested with regards to the most commonly used chip materials. For most materials, the bonding resisted 5 bars at room temperature and 1 bar at 95 °C. This method should find numerous uses, ranging from fast prototyping in the laboratory to implementation in low technology environments or industrial production.

Advances in organic polymer-based monolithic column technology for high-resolution liquid chromatography-mass spectrometry profiling of antibodies, intact proteins, oligonucleotides, and peptides

This review focuses on the preparation of organic polymer-based monolithic stationary phases and their application in the separation of biomolecules, including antibodies, intact proteins and protein isoforms, oligonucleotides, and protein digests. Column and material properties, and the optimization of the macropore structure towards kinetic performance are also discussed. State-of-the-art liquid chromatography-mass spectrometry biomolecule separations are reviewed and practical aspects such as ion-pairing agent selection and carryover are presented. Finally, advances in comprehensive two-dimensional LC separations using monolithic columns, in particular ion-exchange×reversed-phase and reversed-phase×reversed-phase LC separations conducted at high and low pH, are shown.

Solid supports for extraction and preconcentration of proteins and peptides in microfluidic devices: A review

Determination of proteins and peptides is among the main challenges of today's bioanalytical chemistry. The application of microchip technology in this field is an exhaustively developed concept that aims to create integrated and fully automated analytical devices able to quantify or detect one or several proteins from a complex matrix. Selective extraction and preconcentration of targeted proteins and peptides especially from biological fluids is of the highest importance for a successful realization of these microsystems. Incorporation of solid structures or supports is a convenient solution employed to face these demands. This review presents a critical view on the latest achievements in sample processing techniques for protein determination using solid supports in microfluidics. The study covers the period from 2006 to 2015 and focuses mainly on the strategies based on microbeads, monolithic materials and membranes. Less common approaches are also briefly discussed. The reviewed literature suggests future trends which are discussed in the concluding remarks.

On-Chip Fluorescent Labeling using Reversed-phase Monoliths and Microchip Electrophoretic Separations of Selected Preterm Birth Biomarkers

On-chip preconcentration, purification, and fluorescent labeling are desirable sample preparation steps to achieve complete automation in integrated microfluidic systems. In this work, we developed electrokinetically operated microfluidic devices for solid-phase extraction and fluorescent labeling of preterm birth (PTB) biomarkers. Reversed-phase monoliths based on different acrylate monomers were photopolymerized in cyclic olefin copolymer microdevices and studied for the selective retention and elution of a fluorescent dye and PTB biomarkers. Octyl methacrylate-based monoliths with desirable retention and elution characteristics were chosen and used for on-chip fluorescent labeling of three PTB biomarkers. Purification of on-chip labeled samples was done by selective elution of unreacted dye prior to sample. Automated and rapid on-chip fluorescent labeling was achieved with similar efficiency to that obtained for samples labeled off chip. Additionally, protocols for microchip electrophoresis of several off-chip-labeled PTB biomarkers were demonstrated in poly(methyl methacrylate) microfluidic devices. This study is an important step toward the development of integrated on-chip labeling and separation microfluidic devices for PTB biomarkers.

Microfluidics in the selection of affinity reagents for the detection of cancer: paving a way towards future diagnostics

Microfluidic technologies have miniaturized a variety of biomedical applications, and these chip-based systems have several significant advantages over their large-scale counterparts. Recently, this technology has been used for automating labor-intensive and time-consuming screening processes, whereby affinity reagents, including aptamers, peptides, antibodies, polysaccharides, glycoproteins, and a variety of small molecules, are used to probe for molecular biomarkers. When compared to conventional methods, the microfluidic approaches are faster, more compact, require considerably smaller quantities of samples and reagents, and can be automated. Furthermore, they allow for more precise control of reaction conditions (e.g., pH, temperature, and shearing forces) such that more efficient screening can be performed. A variety of affinity reagents for targeting cancer cells or cancer biomarkers are now available and will likely replace conventional antibodies. In this review article, the selection of affinity reagents for cancer cells or cancer biomarkers on microfluidic platforms is reviewed with the aim of highlighting the utility of such approaches in cancer diagnostics.

Tacky cyclic olefin copolymer: a biocompatible bonding technique for the fabrication of microfluidic channels in COC

Cyclic olefin copolymer (COC) is widely used in microfluidics due to its UV-transparency, its biocompatibility and high chemical resistance. Here we present a fast and cost-effective solvent bonding technique, which allows for the efficient bonding of protein-patterned COC structures. The bonding process is carried out at room temperature and takes less than three minutes. Enzyme activity is retained upon bonding and microstructure deformation does not occur.

Design and evaluation of microfluidic devices for two-dimensional spatial separations

Various designs of chips for comprehensive two-dimensional spatial liquid chromatography were investigated. The performance of these chips was initially evaluated using computational fluid dynamics (CFD). A bifurcating distributor with an angle of 140° between branches was implemented in order to achieve a homogeneous velocity field. The cross-sectional area of the channels of the flow distributor was fixed at 0.5 × 0.5 mm, which allows a robust micromilling technique to be used for chip manufacturing. Experiments were performed with chips featuring purposely introduced imperfections in the structure of the bifurcating flow distributor to study its capacity of overcoming potential local clogging. Split peaks were observed when 75% of one of the flow channels was obstructed, in line with the CFD predictions. The main bottlenecks for the performance of the spatial two-dimensional chips were identified, viz. sample injected in the first dimension diverging into the flow distributor and channel discretization (i.e., remixing of first-dimension separation peaks because of finite number of second-dimension channels). Solutions to the former problem were studied by applying a flow resistance in the vertical segments that formed the outlets of the flow distributor and by simulating the presence of constrictions. It was found that a flow resistance of 1.0×10(11) m(-2) reduced the amount of sample diverging into the flow distributor by a factor of 10. The presence of a constriction of 90% of the segment area and 50% of the segment length decreased the diverging flow by a factor of 5. The influence of the linear velocity was significant. Solutions to the channel discretization problem were sought by investigating different designs of spatial two-dimensional chips.

Advances in coupling microfluidic chips to mass spectrometry

Microfluidic technology has shown advantages of low sample consumption, reduced analysis time, high throughput, and potential for integration and automation. Coupling microfluidic chips to mass spectrometry (Chip-MS) can greatly improve the overall analytical performance of MS-based approaches and expand their potential applications. In this article, we review the advances of Chip-MS in the past decade, covering innovations in microchip fabrication, microchips coupled to electrospray ionization (ESI)-MS and matrix-assisted laser desorption/ionization (MALDI)-MS. Development of integrated microfluidic systems for automated MS analysis will be further documented, as well as recent applications of Chip-MS in proteomics, metabolomics, cell analysis, and clinical diagnosis.

Use of vacuum bagging for fabricating thermoplastic microfluidic devices

In this work we present a novel thermal bonding method for thermoplastic microfluidic devices. This simple method employs a modified vacuum bagging technique, a concept borrowed from the aerospace industry, to produce conventional thick substrate microfluidic devices, as well as multi-layer film devices. The bonds produced using this method are superior to those obtained using conventional thermal bonding methods, including thermal lamination, and are capable of sustaining burst pressures in excess of 550 kPa. To illustrate the utility of this method, thick substrate devices were produced, as well as a six-layer film device that incorporated several complex features.

A single low-cost microfabrication approach for polymethylmethacrylate, polystyrene, polycarbonate and polysulfone based microdevices

This paper presents a single microfabrication approach for 4 thermoplastic materials that improve the non-specific adsorption and drying issues inherent to PDMS.

Rapid prototyping of electrochromatography chips for improved two-photon excited fluorescence detection

In the present study, we introduce two-photon excitation at 532 nm for label-free fluorescence detection in chip electrochromatography. Two-photon excitation at 532 nm offers a promising alternative to one-photon excitation at 266 nm, as it enables the use of economic chip materials instead of fused silica. In order to demonstrate these benefits, one-photon and two-photon induced fluorescence detection are compared in different chip layouts and materials with respect to the achievable sensitivity in the detection of polycyclic aromatic hydrocarbons (PAHs). Customized chromatography chips with cover or bottom slides of different material and thickness are produced by means of a rapid prototyping method based on liquid-phase lithography. The design of thin bottom chips (180 μm) enables the use of high-performance immersion objectives with low working distances, which allows one to exploit the full potential of two-photon excitation for a sensitive detection. The developed method is applied for label-free analysis of PAHs separated on a polymer monolith inside polymer glass sandwich chips made from fused silica or soda-lime glass. The obtained limits of detection range from 40 nM to 1.95 μM, with similar sensitivities in fused silica thin bottom chips for one-photon and two-photon excitation. In deep-UV non- or less-transparent devices two-photon excitation is mandatory for label-free detection of aromatics with high sensitivity.

A nano LC-MALDI mass spectrometry droplet interface for the analysis of complex protein samples

The integration of matrix-assisted laser desorption ionization (MALDI) mass spectrometry with an upstream analytical separations (such as liquid chromatography and electrophoresis) has opened up new opportunities for the automated investigation of complex protein and peptide mixtures. The ability to efficiently analyze complex proteomic mixtures in this manner is primarily determined by the ability to preserve spatial discrimination of sample components as they leave the separation column. Current interfacing methods are problematic in this respect since minimum fraction volumes are limited to several microliters. Herein we show for the first time an LC-MALDI interface based on the formation, processing and destruction of a segmented flow. The interface consists of a droplet-generator to fractionate LC effluent into nL-volume droplets and a deposition probe that transfers the sample (and MALDI matrix) onto a conventional MALDI-MS target. The efficacy of the method is demonstrated through the analysis of Trypsin digests of both BSA and Cytochrome C, with a 50% enhancement in analytical performance when compared to conventional interface technology.

Pen microfluidics: rapid desktop manufacturing of sealed thermoplastic microchannels

A unique technique for the rapid fabrication of thermoplastic microfluidic chips is described. The method enables the realization of fully-sealed microchannels in around one hour while requiring only minimal infrastructure by taking advantage of a solvent swelling mechanism that allows raised features to be patterned on the surface of homogeneous thermoplastic materials. Patterning is achieved without photolithography by simply drawing the desired microchannel pattern onto the polymer surface using a suitable ink as a masking layer, either manually or under robotic control, followed by timed exposure to solvent vapor to yield a desired depth for the masked channel features. The channels are then permanently sealed through solvent bonding of the microchannel chip to a mating thermoplastic substrate. The process is demonstrated using cyclic olefin copolymer as a thermoplastic material, with fully operational microfluidic devices fabricated following a true desktop manufacturing model suitable for rapid prototyping.

Charge tunable zwitterionic polyampholyte layers formed in cyclic olefin copolymer microchannels through photochemical graft polymerization

Zwitterionic layers immobilized on various surfaces exhibit ideal biocompatibility and antifouling capability, but direct immobilization of zwitterionic molecules provides limited choice of surface charges. In this paper, the formation of charge tunable zwitterionic polyampholyte layers onto the surface of microfluidic channels of cyclic olefin copolymer by photochemical graft polymerization of mixed acrylic monomers, [2-(acryloyloxy) ethyl] trimethyl ammonium chloride and 2-acrylamido-2-methyl-1-propanesulfonic, under UV illumination was reported. With this method, surface charge of the resulting modification layers could be tailored through the initial monomer ratio and reaction conditions. The incorporation of both monomers into the grafted layers was confirmed by X-ray photoelectron spectroscopy (XPS) and attenuated total reflection Fourier transform infrared (ATR-FTIR). The results indicate that the modified layers are hydrophilic with contact angles of 33.0-44.3°, and the isoelectric points of the modified layers can be tuned from <3 to >9 simply by adjusting the monomer ratios. Elimination of the nonspecific adsorption of proteins on the zwitterionic layers thus formed was proved by fluorescent microscopy and streaming potential measurement. The uniformity of the modified layers was verified through a comparison of electrophoresis inside the modified and native microchannels. A whole blood coagulation time measurement was performed to show its applicability.

New "one-step" method for the simultaneous synthesis and anchoring of organic monolith inside COC microchip channels

A new method for monolith synthesis and anchoring inside cyclic olefin copolymer (COC) microchannels in a single step is proposed. It is shown that type I photoinitiators, typically used in a polymerization mixture to generate free radicals during monolith synthesis, can simultaneously act as type II photoinitiators and react with the plastic surface through hydrogen abstraction. This mechanism is used to "photograft" poly(ethylene glycol) methacrylate (PEGMA) on COC surfaces. Contact angle measurements were used to observe the changes in surface hydrophilicity when increasing initiator concentration and irradiation duration. The ability of type I photoinitiators to synthesize and anchor a monolith inside COC microchannels in a single step was proved through SEM observations. Different concentrations of photoinitiators were tried. Finally, electrochromatographic separations of polycyclic aromatic hydrocarbons were realized to illustrate the beneficial effect of anchoring on chromatographic performances. The versatility of the method was demonstrated with two widely used photoinitiators: benzoin methyl ether (BME) and azobisisobutyronitrile (AIBN).

Disposable microfluidic substrates: transitioning from the research laboratory into the clinic

As more microfluidic applications emerge for clinical diagnostics, the choice of substrate and production method must be considered for eventual regulatory approval. In this review, we survey recent developments in disposable microfluidic substrates and their fabrication methods. We note regulatory approval for disposable microfluidic substrates will be more forthcoming if the substrates are developed with the United States Pharmacopeia's biocompatibility compliance guidelines in mind. We also review the recent trend in microfluidic devices constructed from a hybrid of substrates that takes advantage of each material's attributes.

Liquid chromatography on chip

LC is one of the most powerful separation techniques as illustrated by its leading role in analytical sciences through both academic and industrial communities. Its implementation in microsystems appears to be crucial in the development of mu-Total Analysis System. If electrophoretic techniques have been widely used in miniaturized devices, LC has faced multiple challenges in the downsizing process. During the past 5 years, significant breakthroughs have been achieved in this research area, in both conception and use of LC on chip. This review emphasizes the development of novel stationary phases and their implementation in microchannels. Recent instrumental advances are also presented, highlighting the various driving forces (pressure, electrical field) that have been selected and their respective ranges of applications.

A cyclo olefin polymer microfluidic chip with integrated gold microelectrodes for aqueous and non-aqueous electrochemistry

This paper presents an entirely polymeric microfluidic system, made of cyclo olefin polymer (COP), with integrated gold microband electrodes for electrochemical applications in organic media. In the present work, we take advantage of the COP's high chemical stability to polar organic solvents in two different ways: (i) to fabricate gold microelectrodes using COP as a substrate by standard lithographic and lift-off techniques; and (ii) to perform electrochemical experiments in organic media. In particular, fourteen parallel gold microelectrodes with a width of 14 microm and separated from their closest neighbour by 16 microm were fabricated by lithographic and lift-off techniques on a 188 microm thick COP sheet. A closed channel configuration was obtained by pressure-assisted thermal bonding between the COP sheet containing the microelectrodes and a microstructured COP sheet, where a 3 cm long, 50 microm wide and 24 microm deep channel was fabricated via hot embossing. Cyclic voltammetric measurements were carried out in aqueous and organic media, using a solution consisting of 5 mM ferrocyanide/ferricyanide in 0.5 M KNO(3) and 5 mM ferrocene in 0.1 M TBAP/acetonitrile, respectively. Experimental currents obtained for different flow rates ranging from 1 to 10 microL min(-1) were compared to the theoretical steady state currents calculated by the Levich equation for a band electrode (R. G. Compton, A. C. Fisher, R. G. Wellington, P. J. Dobson and P. A. Leigh, J. Phys. Chem., 1993, 97, 10410-10415). In both cases, the difference between the experimental and the predicted data is less than 5%, thus validating the behaviour of the fabricated device. This result opens the possibility to use a microfluidic system made entirely from COP with integrated microband electrodes in organic electroanalysis and in electrosynthesis.

Microchip electrospray performance during gradient elution with bulk conductivity changes

This work identifies dynamic changes in bulk conductivity during reversed-phase HPLC gradient elution as a major source for spray mode changes and instabilities observed in ESI-MS. A commercial microchip-HPLC/ESI-MS configuration was modified to enable electrospray diagnostics based on frequency analysis of the microchip emitter current combined with spray imaging. This approach facilitated detection of different spray modes together with their onset potentials. Water/acetonitrile mixtures containing formic acid were selected as the electrosprayed solutions to represent typical conditions in reversed-phase HPLC. Experimental data are complemented by computational fluid dynamics simulations, treating the electrosprayed solution as leaky dielectric fluid, to address the influence of bulk conductivity and applied potential difference on the developing cone-jet morphology and stability.

Microfluidic Device for Coupling Capillary Electrophoresis and Matrix-Assisted Laser Desorption Ionization-Mass Spectrometry

We have designed and fabricated a polydimethylsiloxane (PDMS) microfluidic device for coupling capillary electrophoresis (CE) and matrix-assisted laser desorption ionization-mass spectrometry (MALDI-MS). The coupling is advantageous in biological research because CE has the power of separating analytes in a sample based on mobility difference and MALDI-MS provides accurate and sensitive mass analysis of the analytes. The goal is realized by fractionating the separated analytes inside the microfluidic device and pushing the analyte fractions into open reservoirs. Each analyte fraction is then mixed with a matrix solution and deposited on a MALDI target for MALDI-MS. Therefore, a two-step analysis of analytes in the form of CE-MALDI-MS is achieved by using the microfluidic device.

Microfluidics with MALDI analysis for proteomics--a review

Various microfluidic devices have been developed for proteomic analyses and many of these have been designed specifically for mass spectrometry detection. In this review, we present an overview of chip fabrication, microfluidic components, and the interfacing of these devices to matrix-assisted laser desorption ionization (MALDI) mass spectrometry. These devices can be directly coupled to the mass spectrometer for on-line analysis in real-time, or samples can be analyzed on-chip or deposited onto targets for off-line readout. Several approaches for combining microfluidic devices with analytical functions such as sample cleanup, digestion, and separations with MALDI mass spectrometry are discussed.

An array of ordered pillars with retentive properties for pressure-driven liquid chromatography fabricated directly from an unmodified cyclo olefin polymer

The current paper describes the development and characterization of a pillar array chip that is constructed out of a sandwich of cyclo olefin polymer (COP) sheets. The silicon master of a 5 cm long pillar array was embossed into the COP, yielding 4.3 microm deep pillars of 15.3 microm diameter with an external porosity of 43 % and a well designed sidewall region to avoid side wall induced band broadening. A closed channel configuration was obtained by pressure assisted thermal bonding to a non-processed COP lid. Injection of coumarin dye plugs and detection with a fluorescence microscope showed very close agreement of this channel configuration to theoretical expectations in terms of band broadening. This agreement is due to the low taper, the optimized sidewall region and the excellent bonding quality between the two polymer sheets, even at the pillar area. Under non-retained conditions (pure methanol as mobile phase), plate heights as low as 4 microm were obtained. Under retained conditions, using the native hydrophobic properties of the COP channel (in 70/30 v/v water/methanol mixture as mobile phase), a minimum plate height of 6 microm was obtained. A 4 component separation was successfully achieved, demonstrating that COP is a cheap and efficient alternative for silicon and silica based liquid chromatography formats.

Microfluidic chips for mass spectrometry-based proteomics

Microfluidic devices coupled to mass spectrometers have emerged as excellent tools for solving the complex analytical challenges associated with the field of proteomics. Current proteome identification procedures are accomplished through a series of steps that require many hours of labor-intensive work. Microfluidics can play an important role in proteomic sample preparation steps prior to mass spectral identification such as sample cleanup, digestion, and separations due to its ability to handle small sample quantities with the potential for high-throughput parallel analysis. To utilize microfluidic devices for proteomic analysis, an efficient interface between the microchip and the mass spectrometer is required. This tutorial provides an overview of the technologies and applications of microfluidic chips coupled to mass spectrometry for proteome analysis. Various approaches for combining microfluidic devices with electrospray ionization (ESI) and matrix-assisted laser desorption/ionization (MALDI) are summarized and applications of chip-based separations and digestion technologies to proteomic analysis are presented.

Polymer microchips integrating solid-phase extraction and high-performance liquid chromatography using reversed-phase polymethacrylate monoliths

Polymer microfluidic chips employing in situ photopolymerized polymethacrylate monoliths for high-performance liquid chromatography separations of peptides is described. The integrated chip design employs a 15 cm long separation column containing a reversed-phase polymethacrylate monolith as a stationary phase, with its front end seamlessly coupled to a 5 mm long methacrylate monolith which functions as a solid-phase extraction (SPE) element for sample cleanup and enrichment, serving to increase both detection sensitivity and separation performance. In addition to sample concentration and separation, solvent splitting is also performed on-chip, allowing the use of a conventional LC pump for the generation of on-chip nanoflow solvent gradients. The integrated platform takes advantage of solvent bonding and a novel high-pressure needle interface which together enable the polymer chips to withstand internal pressures above 20 MPa (approximately 2900 psi) for efficient pressure-driven HPLC separations. Gradient reversed-phase separation of fluorescein-labeled model peptides and BSA tryptic digest are demonstrated using the microchip HPLC system. Online removal of free fluorescein and enrichment of labeled proteins are simultaneously achieved using the on-chip SPE column, resulting in a 150-fold improvement in sensitivity and a 10-fold reduction in peak width in the following microchip gradient LC separation.

Development of an acrylate monolith in a cyclo-olefin copolymer microfluidic device for chip electrochromatography separation

An acrylate monolith has been synthesized into a cyclic olefin copolymer microdevice for reversed-phase electrochromatography purposes. Microchannels, designed by hot embossing, were filled up with an acrylate monolith to serve as a hydrophobic stationary phase. A lauryl acrylate monolith was formulated to suit the hydrophobic material, by implementing 100% organic porogenic solvent. This new composition was tested in capillary prior to its transfer into the microfluidic device. Surface functionalization of the cyclic olefin copolymer surface was applied using UV-grafting technique to improve the covalent attachment of this monolith to the plastic walls of the microfluidic chip. The on-chip performances of this monolith were evaluated in detail for the reversed-phase electrochromatographic separation of polycyclic aromatic hydrocarbons, with plate heights reaching down to 10 microm when working at optimal velocity.

High-pressure needle interface for thermoplastic microfluidics

A robust and low dead volume world-to-chip interface for thermoplastic microfluidics has been developed. The high pressure fluidic port employs a stainless steel needle inserted into a mating hole aligned to an embedded microchannel, with an interference fit used to increase pressure resistance. Alternately, a self-tapping threaded needle screwed into a mating hole is also demonstrated. In both cases, the flat bottom needle ports seat directly against the microchannel substrate, ensuring low interfacial dead volumes. Low dispersion is observed for dye bands passing the interfaces. The needle ports offer sufficient pull-out forces for applications such as liquid chromatography that require high internal fluid pressures, with the epoxy-free interfaces compatible with internal microchannel pressures above 40 MPa.

Structure-transport analysis for particulate packings in trapezoidal microchip separation channels

This article investigates the efficiency of particulate beds confined in quadrilateral microchannels by analyzing the three-dimensional fluid flow velocity field and accompanying hydrodynamic dispersion with quantitative numerical simulation methods. Random-close packings of uniform, solid (impermeable), spherical particles of diameter d(p) were generated by a modified Jodrey-Tory algorithm in eighteen different conduits with quadratic, rectangular, or trapezoidal cross-section at an average bed porosity (interparticle void fraction) of epsilon = 0.48. Velocity fields were calculated by the lattice Boltzmann method, and axial hydrodynamic dispersion of an inert tracer was simulated at Péclet numbers Pe = u(av)d(p)/D(m) (where u(av) is the average fluid flow velocity through a packing and D(m) the bulk molecular diffusion coefficient) from Pe = 5 to Pe = 30 by a Lagrangian particle-tracking method. All conduits had a cross-sectional area of 100d(p)(2) and a length of 1200d(p), translating to around 10(5) particles per packing. We present lateral porosity distribution functions and analyze fluid flow profiles and velocity distribution functions with respect to the base angle and the aspect ratio of the lateral dimensions of the different conduits. We demonstrate significant differences between the top and bottom parts of trapezoidal packings in their lateral porosity and velocity distribution functions, and show that these differences increase with decreasing base angle and increasing base-aspect ratio of a trapezoidal conduit, i.e., with increasing deviation from regular rectangular geometry. Efficiencies are investigated in terms of the axial hydrodynamic dispersion coefficients as a function of the base angle and base-aspect ratio of the conduits. The presented data support the conclusion that the efficiency of particulate beds in trapezoidal microchannels strongly depends on the lateral dimensions of the conduit and that cross-sectional designs based on large side-aspect-ratio rectangles with limited deviations from orthogonality are favorable.

Hydrophilic surface modification of cyclic olefin copolymer microfluidic chips using sequential photografting

The plastic material known as cyclic olefin copolymer (COC) is a useful substrate material for fabricating microfluidic devices due to its low cost, ease of fabrication, excellent optical properties, and resistance to many solvents. However, the hydrophobicity of native COC limits its use in bioanalytical applications. To increase surface hydrophilicity and reduce protein adsorption, COC surfaces were photografted with poly(ethylene glycol) methacrylate (PEGMA) using a two-step sequential approach: covalently-bound surface initiators were formed in the first step and graft polymerization of PEGMA was then carried out from these sites in the second step. Contact angle measurements were used to monitor and quantify the changes in surface hydrophilicity as a function of grafting conditions. As water droplet contact angles decreased from 88 degrees for native COC to 45 degrees for PEGMA-grafted surfaces, protein adsorption was also reduced by 78% for the PEGMA-modified COC microchannels as determined by a fluorescence assay. This photografting technique should enable the use of COC microdevices in a variety of bioanalytical applications that require minimal nonspecific adsorption of biomolecules.