Coupling of sequential injection analysis and capillary electrophoresis - Laser-induced fluorescence via a valve interface for on-line derivatization and analysis of amino acids and peptides

A comprehensive review on LED-induced fluorescence in diagnostic pathology

Sensitivity, specificity, mobility, and affordability are important criteria to consider for developing diagnostic instruments in common use. Fluorescence spectroscopy has been demonstrating substantial potential in the clinical diagnosis of diseases and evaluating the underlying causes of pathogenesis. A higher degree of device integration with appropriate sensitivity and reasonable cost would further boost the value of the fluorescence techniques in clinical diagnosis and aid in the reduction of healthcare expenses, which is a key economic concern in emerging markets. Light-emitting diodes (LEDs), which are inexpensive and smaller are attractive alternatives to conventional excitation sources in fluorescence spectroscopy, are gaining a lot of momentum in the development of affordable, compact analytical instruments of clinical relevance. The commercial availability of a broad range of LED wavelengths (255-4600 nm) has opened up new avenues for targeting a wide range of clinically significant molecules (both endogenous and exogenous), thereby diagnosing a range of clinical illnesses. As a result, we have specifically examined the uses of LED-induced fluorescence (LED-IF) in preclinical and clinical evaluations of pathological conditions, considering the present advancements in the field.

Complete capillary electrophoresis process on a drone: towards a flying micro-lab

Hazardous remote places exist in the world. Why should health or life be risked sending a scientist to the investigation site, as the remote analytical instrumentation exists? Different scientific fields require instruments that could be used on-site (in situ), therefore the purpose of this work was to design a fully automated chemical analysis system small enough to be mountable on a drone. Here we show an autonomous analytical system with sampling capability on a drone. The system is suited for the remote and autonomous analysis of volatile and non-volatile chemicals in the air. The designed system weighs less than 800 g. Data are transmitted wirelessly. Collected substances are separated automatically without the intervention of the operator using the method of capillary zone electrophoresis. The analytes are detected using a miniaturized contactless conductivity detector quantifying them down to less than 1 μM. In this work, we demonstrated sampling and separation of volatile amines (triethylamine and diethylamine) and organic acids (acetic and formic acids), non-volatile inorganic cations (K⁺, Ca²⁺, Na⁺), and protein (bovine serum albumin) in the aerosol state. It was shown that the capillary electrophoretic analysis can be performed on a hovering drone. We anticipate our work to be a starting point for more sophisticated, autonomous complex sample analysis. We believe that our designed instrument will enable the investigation of hazardous places in different research fields.

Determination of phenylenediamines in hair colors derivatizated with 5-(4, 6-dichlorotriazinyl)aminofluorescein via micellar electrokinetic chromatography

Phenylenediamines (PDs), which are reported to cause allergic dermatitis and possess genotoxicity and carcinogenicity, are the ingredients used in permanent hair dyes. The fluorescent derivatization strategy coupled with micellar electrokinetic chromatography (MEKC) were established to analyze four PDs, including o-phenylenediamine (OPD), m-phenylenediamine (MPD), p-phenylenediamine (PPD) and toluene-2,5-diamine (PTD). Additionally, 5-(4, 6-dichlorotriazinyl) aminofluorescein (DTAF) was used as a fluorescent reagent derived at amino groups of PDs and underwent nucleophilic substitution reaction to improve the detection sensitivity. The derivatization condition reacted at 90 °C for 10 min in alkaline conditions. The optimized separation conditions were 20 mM borate (pH 8.0) containing 10 mM Brij 35 and 35% (v/v) methanol. The limits of detection (S/N = 3) for MPD, PTD, PPD and OPD were 25, 25, 50 and 100 nM, respectively. Compared to MEKC-UV, the sensitivity enhancements were 30- to 81-fold when PDs were derived with DTAF. The high-sensitivity MEKC-LIF method was successfully established and applied to determine PDs in commercial hair colors for quality control and in real hair samples for evaluating the location of PDs in dyed hair samples, as well as in percutaneous absorption samples for evaluating the ability of PDs to penetrate skin.

Recent advances in flow injection analysis

A dynamic development of methodologies of analytical flow injection measurements during four decades since their invention has reinforced the solid position of flow analysis in the arsenal of techniques and instrumentation of contemporary chemical analysis.

Study on urinary profile of inborn errors of metabolism by 18-crown-6 modified capillary electrophoresis with laser-induced fluorescence detection

Newborn screening in urine is important for the diagnosis of many inborn errors of metabolism (IEM). Capillary electrophoresis with laser-induced fluorescence detection (CE-LIF) is a major technological advance in screening IEM. It has the advantage of sensitive and simultaneous multiple disease screening with minimal sample requirement. The analytes were derivatized with fluorescein isothiocyanate (FITC) prior to CE-LIF analysis. In urine samples, free amino acids (AAs) were well separated from other coexisting components, exhibiting a linear calibration over the concentration range 0.01-5.0μmol/L with the limits of detection (LODs) ranging from 0.005 to 0.010μmol/L. The relative standard deviations (RSDs) were in the range 0.1-1.0% for peak area, and 0.2-1.0% for migration time, respectively. Under optimized conditions, the method presented here has been successfully used for the simultaneous and sensitive analysis of seven AAs in urine samples of newborn babies, and evaluating the effect of therapy as well.

Laboratory automation based on flow techniques

Flow techniques have undoubtedly aroused special interest in relation to many other automatic methodologies of analysis. Ever since segmented flow analysis (SFA) was developed by Skeggs in 1957, flow techniques have been in continuous evolution toward new develop-ments. There is no solid argument in favor of using any particular flow technique separately; rather, substantial advantages can be derived from their combination. Since flow-based methods are nonseparative tools, the advantages of combining flow techniques with separation techniques are noteworthy. High selectivity can be achieved by coupling them with liquid chromatography (LC), gas chromatography (GC), solid-phase extraction (SPE), or capillary electrophoresis (CE). Thus, a detailed description of flow techniques, their evolution, their hyphenation advantages, and a critical comparison between current developed methods exploiting flow techniques aimed at solving present analytical needs are reviewed in this article.

Microelectrophoresis platform for fast serial analysis of single cells

A capillary-based microelectrophoresis platform for fast serial analysis of single cells is described. In this system, the capillary remains fixed and a two-channel flow system is used to rapidly switch the buffer surrounding the capillary inlet from a physiological buffer to an electrophoretic buffer. Single cells are retained in the physiologic buffer channel utilizing an array of cell microwells patterned into the channel floor. The defined addresses of the cells on the array enable the sequential delivery of individual cells to the inlet of the capillary, where a focused laser pulse lyses the cell. The cell chamber is moved along a preordained route so that the inlet of the capillary is located in the electrophoresis buffer for separation and the physiological buffer during cell sampling. The throughput of the current system is limited by peak overlap between successive samples. Key characterizations of this system including the fluid flow rates, the cell array dimensions, and laser energies were performed. To demonstrate this system, 28 cells loaded with Oregon green and fluorescein were serially analyzed in under 16 min, a rate of 1.8 cells/min.

Chemometrical examination of active parameters and interactions in flow injection-capillary electrophoresis

The first detailed examination of flow injection-capillary electrophoresis (FI-CE) active parameters and their interactions via response surface methodology (RSM) is presented. Specifically, RSM in the form of a Box-Behnken design was implemented to effectively predict the significance of capillary length, voltage and injection volume on the optimization of an in-house built FI-CE analyzer. Initial studies were performed assessing peak height and peak shape of the model compound N,N-dimethylformamide. Optimum model conditions were then derived and used in the model separation of two small molecules, nicotinamide adenine dinucleotide, reduced form (NADH) and benzenesulfonamide. By implementing the RSM approach, detailed examination of active FI-CE parameters was possible, including the ability to reveal a significant interactive effect. This work is not only highly significant for advancing FI-CE developments, but instructive for investigators actively exploring other coupled analytical techniques and associated experimental parameters.

Hemolymph amino acid analysis of individual Drosophila larvae

One of the most widely used transgenic animal models in biology is Drosophila melanogaster, the fruit fly. Chemical information from this exceedingly small organism is usually accomplished by studying populations to attain sample volumes suitable for standard analysis methods. This paper describes a direct sampling technique capable of obtaining 50-300 nL of hemolymph from individual Drosophila larvae. Hemolymph sampling performed under mineral oil and in air at 30 s intervals up to 120 s after piercing larvae revealed that the effect of evaporation on amino acid concentrations is insignificant when the sample was collected within 60 s. Qualitative and quantitative amino acid analyses of obtained hemolymph were carried out in two optimized buffer conditions by capillary electrophoresis with laser-induced fluorescence detection after derivatizing with fluorescamine. Thirteen amino acids were identified from individual hemolymph samples of both wild-type (WT) control and the genderblind (gb) mutant larvae. The levels of glutamine, glutamate, and taurine in the gb hemolymph were significantly lower at 35%, 38%, and 57% of WT levels, respectively. The developed technique that samples only the hemolymph fluid is efficient and enables accurate organism-level chemical information while minimizing errors associated with possible sample contaminations, estimations, and effects of evaporation compared to the traditional hemolymph-sampling techniques.

Recent developments in CE and CEC of peptides

The article brings a comprehensive survey of recent developments and applications of high-performance capillary electromigration methods, zone electrophoresis, ITP, IEF, affinity electrophoresis, EKC, and electrochromatography, to analysis, preparation, and physicochemical characterization of peptides. New approaches to the theoretical description and experimental verification of electromigration behavior of peptides and to methodology of their separations, such as sample preparation, adsorption suppression, and detection, are presented. Novel developments in individual CE and CEC modes are shown and several types of their applications to peptide analysis are presented: conventional qualitative and quantitative analysis, purity control, determination in biomatrices, monitoring of chemical and enzymatical reactions and physical changes, amino acid and sequence analysis, and peptide mapping of proteins. Some examples of micropreparative peptide separations are given and capabilities of CE and CEC techniques to provide important physicochemical characteristics of peptides are demonstrated.

Coaxial flow system for chemical cytometry

Over the past decade, chemical cytometry performed by capillary electrophoresis (CE) has become increasingly valuable as a bioanalytical tool to quantify analytes from single cells. However, extensive use of CE-based chemical cytometry has been hindered by the relatively low throughput for the analysis of single adherent cells. In order to overcome the low throughput of CE-based analysis of adherent cells and increase its utility in evaluating cellular attributes, new higher throughput methods are needed. Integration of a coaxial buffer exchange system with CE-based chemical cytometry increased the rate of serial analyses of cells. In the designed system, fluid flow through a tube coaxial to the separation capillary was used to supply electrophoretic buffer to the capillary. This sheath or coaxial fluid was turned off between analysis of cells and on during cell sampling and electrophoresis. Thus, living cells were not exposed to the nonphysiologic electrophoretic buffer prior to lysis. Key parameters of the system such as the relative capillary-sheath positions, buffer flow velocities, and the cell chamber design were optimized. To demonstrate the utility of the system, rat basophilic leukemic cells loaded with Oregon green and fluorescein were serially lysed and loaded into a capillary. Separation of the contents of 20 cells at a rate of 0.5 cells/min was demonstrated.