Poly(2-N-carbazolylethyl acrylate)-modified silica as a new polymeric stationary phase for reversed-phase high-performance liquid chromatography

Fabrication of Carbon-Like, π-Conjugated Organic Layer on a Nano-Porous Silica Surface

This paper presents a new type of black organic material-porous silica composite providing an extremely highly selective adsorption surface. This black composite was prepared by lamination on nano-sized pores with a carbon-like, π-extended structure, which can be converted via the on-site polymerization of 1,5-dihydroxynaphthalene with a triazinane derivative and a thermally induced condensation reaction with denitrification. This bottom-up fabrication method on porous materials had the great advantage of maintaining the pore characteristics of a raw porous material, but also the resultant black surface exhibited an extremely high molecular-shape selectivity; for example, that for trans- and cis-stilbenes reached 14.0 with the black layer-laminated porous silica, whereas it was below 1.2 with simple hydrophobized silica.

A pH-stable, crosslinked stationary phase based on the thiol-yne reaction

Stationary phases that can withstand extremes of pH and temperature are needed to allow a single column to accommodate a wider set of solutes and separation criteria. We used a simple multi-step process using the thiol-yne reaction following the modification of the silica surface with a thiol-containing silane. The monomers 1,4-diethynylbenzene (DEB) and 1,6-hexanedithiol were used to create a crosslinked thiol-yne (CTY) stationary phase along the surface of the thiol functionalized silica. In the Tanaka test characterization, the CTY phase showed a low phase ratio, methylene selectivity typical of a reversed phase, and extremely high shape selectivity compared to commercial reversed phases. The hydrophobic subtraction model characterization showed a high positive steric resistance, a low hydrogen bond acidity, and a high cation-exchange capacity compared to most reversed phases. At pH 0.5 with an 85% aqueous mobile phase the phase showed no significant change over 114 h. With a 50% aqueous mobile phase the phase took four more days than a sterically protected C18 phase for the k' to decline 25%. At pH 12.6, 50% aqueous mobile phase, a sterically protected C18 phase showed a 20% decrease in k' and more than a 60% decrease in theoretical plates per meter in three hours. The CTY phase actually showed modest increases in k' and theoretical plates per meter after three hours.

Monolithic poly(N-vinylcarbazole-co-1,4-divinylbenzene) capillary columns for the separation of biomolecules

Monolithic capillary columns were prepared by thermally initiated free radical copolymerization of N-vinylcarbazole (NVC) and 1,4-divinylbenzene (DVB) within the confines of 200 and 100 μm i.d. fused silica capillaries. The reaction was carried out under the influence of inert micro-(toluene) and macroporogen (1-decanol) and α,α'-azoisobutyronitrile (AIBN) as a free radical initiator. The material proved high mechanical stability applying water and acetonitrile as mobile phases. The morphological and porous properties were studied by scanning electron microscopy (SEM), nitrogen sorption (BET) and mercury intrusion porosimetry (MIP). The homogeneity of the copolymerization process was confirmed by elemental analysis and monomer conversion measurements. The newly developed NVC/DVB monolithic supports showed high separation efficiency towards biomolecules, applying reversed-phase (RP) and ion-pair reversed-phase (IP-RP) separation modes, which is exemplified by the separations of peptides, proteins and oligonucleotides. Furthermore the maximum loading capacity was evaluated. The chromatographic performance under isocratic elution was determined in terms of theoretical plate number and plate height, where up to 41,000 plates per column and a minimum plate height value of 1.7 μm were achieved, applying oligonucleotide separations. In gradient elution mode, peak capacities of 96 and 127 were achieved within a gradient time window of 60 min for protein and oligonucleotide separations, respectively. The material proved to have high permeability, good repeatability of the fabrication process and high surface areas in the range of 120-160 m(2) g(-1).