Hypercrosslinking: new approach to porous polymer monolithic capillary columns with large surface area for the highly efficient separation of small molecules

Monolithic stationary phases prepared via cyclic anhydride ring-opening polymerization as tunable platforms for chromatographic applications

Polymer monolithic stationary phases were prepared based on a cyclic anhydride as a reactive and tunable platform via ring-opening post-polymerization using primary amines, octadecylamine and benzylamine. The characterization techniques indicated the insertion of the functional groups into the original monoliths and confirmed the amidation reactions. The post-polymerization modification also improved the monolith's thermal and mechanical stability and induced significant improvement in their surface area. The stationary phases were synthesized inside small dimension stainless-steel columns (2.1 mm i.d. × 50 mm length). The prepared columns before and after modifications have been tested for the separation of the alkylbenzene series and some polycyclic aromatic hydrocarbons (PAHs) as model compounds. In all cases, the chromatographic performance in terms of the height equivalent to a theoretical plate on the functionalized monoliths was remarkably improved when compared with that on the unmodified monolith, which was between 9.59-39.49 μm and 4.08-31.50 μm using monoliths modified with octadecylamine and benzylamine, respectively. Under the same chromatographic conditions, the functionalization of monoliths with octadecylamine provided more hydrophobic interactions and enhanced the retention of alkylbenzenes, while the modification of monoliths with benzyl groups improved the separation and the retention of the PAHs through the strong π-π interactions. However, post-modification polymerization with octadecylamine and benzylamine enhanced the separation efficiency of the prepared columns toward all studied compounds. The repeatability of the injections on the same column and the reproducibility of the prepared columns have been studied for some selected parameters and estimated in terms of percent relative standard deviation (%RSD) for some of the studied compounds. The repeatability of the prepared columns was ≤9.42% (n = 5) based on run-to-run injections and ≤9.48% based on day-to-day injections for five successive days. The reproducibility levels, on the other hand, were ≤20.95% for all studied parameters in all cases. To assess their performance for the analysis of real samples, the applicability of the prepared columns was examined for the separation of the active ingredients extracted from some commercial pharmaceutical formulations and for the separation of tea water extract constituents. The validation data show the suitability of the columns for practical use in the routine analysis of these samples.

Characterization of hybrid organo-silica monoliths for possible application in the gradient elution of peptides

We characterized thermally polymerized organo-silica hybrid monolithic capillaries to test their applicability in the gradient elution of peptides. We have used a single-pot approach utilizing 3-(methacryloyloxy)propyltrimethoxysilane (MPTMS), ethylene dimethacrylate (EDMA), and n-octadecyl methacrylate (ODM) as functional monomers. The organo-silica monolith containing MPTMS and EDMA was compared with the stationary phase prepared by adding ODM to the original polymerization mixture. Column prepared using a three-monomer system provided a lower accessible volume of flow-through pores, a higher proportion of mesopores, and higher efficiency. We utilized isocratic and gradient elution data to predict peak widths in gradient elution. Both protocols provided comparable results and can be used for peptide peak width prediction. However, applying gradient elution data for peak width prediction seems simpler. Finally, we tested the effect of gradient time on achievable peak capacity in the gradient elution of peptides with a column prepared with a three-monomer system providing a higher peak capacity. However, the performance of hybrid organo-silica monolithic stationary phases in gradient elution of peptides must be improved compared to other monolithic stationary phases. The limiting factor is column efficiency in highly aqueous mobile phases, which needs to be focused on.

Porous carbon black-polymer composites for volatile organic compound adsorption and efficient microwave-assisted desorption

Adsorbents with high surface area, thermal stability and microwave absorption ability are highly desired for cyclic adsorption and microwave regeneration processes. However, most polymeric adsorbents are transparent to microwaves. Herein, porous hyper-crosslinked polymers (HCP) of (4,4'-bis((chloromethyl)-1,1'-biphenyl-benzyl chloride)) with different carbon black (CB) contents were synthesized via the Friedel-Crafts reaction. CB was selected as the filler due to its low cost and high dielectric loss and was embedded inside the polymer structure during polymerization. CB-containing composites showed enhanced thermal stability at elevated temperatures, and more than a 90-times increase in the dielectric loss factor, which is favorable for microwave regeneration. Nitrogen physisorption analysis by the Bruner-Emmett-Teller isotherms demonstrated that CB presence in the polymer structure nonlinearly decreases the surface area and total pore volume (by 38% and 26%, respectively at the highest CB load). Based on the characterization testing, 4 wt% of CB was found to be an optimum filler content, having the highest MW absorption and minimal effect on the adsorbent porosity. HCP with 4 wt% CB allowed a substantial increase in the desorption temperature and yielded more than a 450% enhancement in the desorption efficiency compared to HCP without CB.

Fabrication of monolithic capillary columns with inner diameter 50-530 μm employing a mixture of pentaerythritol tetraacrylate and polyhedral oligomeric silsesquioxane-methacrylate as crosslinkers

Highly crosslinked monolithic capillary columns with inner diameters in the range of 50-530 μm were prepared by radical polymerization of pentaerythritol tetraacrylate, polyhedral oligomeric silsesquioxane-methacrylate, and n-octadecyl methacrylate in the presence of methanol, dodecyl alcohol, and polyethyleneglycol lauryl ether. Columns were evaluated by inverse size-exclusion chromatography employing a set of polystyrene standards of narrow molecular-size distribution and by scanning electron microscopy. Chromatographic performance under reversed-phase conditions was also evaluated. The combination of two effective crosslinkers as pentaerythritol tetraacrylate and polyhedral oligomeric silsesquioxane-methacrylate in the polymerization mixture allows for the preparation of robust and efficient monolithic capillary columns within a fairly wide range of internal diameters. This article is protected by copyright. All rights reserved.

Preparation and properties of GC capillary column with hypercrosslinked stationary phase

For the first time, highly porous hypercrosslinked polystyrene layer was synthesized within a gas chromatography capillary column and successfully deposited onto the capillary walls generating porous layer open-tubular capillary column. Elaborated three steps synthetic procedure provides tightly bonded porous polymeric layer and ensues complete elimination of particle shedding and the needs for particle traps. Due to highly developed surface area, porous layer open-tubular column provides strong solute retention that is useful for the separation of various volatile solvents and light gas compounds including ethane, ethylene, ethyne. Aqueous injections will not harm the column.

Influence of Functional Group Concentration on Hypercrosslinking of Poly(vinylbenzyl chloride) PolyHIPEs: Upgrading Macroporosity with Nanoporosity

With the aim to study the influence of monomer ratio in poly(high internal phase emulsions) (polyHIPEs) on the polymer network architecture and morphology of poly(vinylbenzyl chloride-co-divinylbenzene-co-styrene) after hypercrosslinking via the internal Friedel–Crafts process, polyHIPEs with 80% overall porosity were prepared at three different initial crosslinking degrees, namely 2, 5, and 10 mol.%. All had typical interconnected cellular morphology, which was not affected by the hypercrosslinking process. Nitrogen adsorption and desorption experiments with BET and t-plot modelling were used for the evaluation of the newly introduced nanoporosity and in combination with elemental analysis for the evaluation of the extent of the hypercrosslinking. It was found that, for all three initial crosslinking degrees, the minimum amount of functional monomer, 4-vinylbenzyl chloride, was approximately 30 mol.%. Hypercrosslinking of polymers with lower concentrations of functional monomer did not result in induction of nanoporosity while the initial crosslinking degree had a much lower impact on the formation of nanoporosity.

Poly(carboxyethyl acrylate-co-ethylene glycol dimethacrylate) precursor monolith with bonded octadecyl ligands for use in reversed-phase capillary electrochromatography

A carboxy precursor monolithic column, namely poly(carboxy ethyl acrylate-co-ethylene glycol dimethacrylate) was first produced in a 100 μm i.d. fused-silica capillary and subsequently surface bonded with n-octadecyl (C₁₈ ) ligands by a post-polymerization functionalization process with octadecylamine in the presence of N,N´-dicyclohexylcarbodiimide. The bonding of octadecyl ligands was achieved via an amide linkage between the carboxy functions of the precursor monolith and the amino group of the octadecylamine compound. The resulting C₁₈ monolith exhibited a very low electroosmotic flow (EOF), a fact that required the incorporation of small amounts of 2-acrylamido-2-methylpropane sulfonic acid (AMPS) in the polymerization solution to produce a precursor monolith with fixed negative charges of sulfonate groups. This may indicate that the conjugation of the carboxy functions with octadecylamine occurred to a large extent so that the amount of residual carboxy functions was sparsely dispersed and not enough to produce a desirable EOF. The EOF velocity of the C₁₈ column having fixed negative charges provided by the incorporated AMPS increased with increasing ACN content of the mobile phase signaling an increased binding of mobile phase ions to the polar amide linkages near the monolithic surface, and a decreased viscosity of the mobile phase, both of which would result in increased EOF velocity. The C₁₈ monolithic column constituted a novel nonpolar sorbent for reversed-phase capillary electrochromatography for nonpolar solutes, e.g., alkylbenzenes, alkylphenyl ketones, and polyaromatic hydrocarbons, and slightly polar compounds including phenol and chlorophenols. The C₁₈ monolithic column exhibited relatively high selectivity toward chlorophenols differing by one chloro substituent.

One-Pot Fabrication of Hierarchically Bicontinuous Polystyrene Monoliths with Homogeneous Skeletons and Glycopolymer Surfaces

The hierarchically bicontinuous polystyrene monoliths (HBPMs) with homogeneous skeletons and glycopolymer surfaces are fabricated for the first time based on the medium internal phase emulsion (MIPE) templating method via activator generated by electron transfer for atom transfer radical polymerization (AGET ATRP). The synergistic self-assembly of amphiphilic diblock glycopolymer (ADG) and Pluronic F127 (PF127) at the oil/water interface via hydrogen bonding interaction contributes to the formation of bicontinuous MIPE with deformed neighboring water droplets, resulting in the highly interconnected HBPM after polymerization. There is a bimodal pore size distribution in the HBPM, that is, through pores (150-5000 nm) and mesopores (10-150 nm). The HBPMs as prepared show excellent biocompatibility, homogeneous skeletons, strong mechanical strength, and high bed permeability, overcoming the practical limitations of the second generation of polystyrene (PS) monoliths. Glycoprotein concanavalin A (Con A) can be easily and quickly separated by the HBPM in hydrophilic interaction chromatography (HILIC) mode. These results suggest the HBPMs have great potentials in catalysis, separations, and biomedical applications.

Hybrid Microporous Polymeric Materials with Outstanding Permeability and Increased Gas Transport Stability: PTMSP Aging Prevention by Sorption of the Polymerization Catalyst on HCPS

The influence of hyper-crosslinked polystyrene (HCPS) Macronet^TM MN200 on the gas transport properties and aging of the highly permeable glassy polymer poly(1-trimethylsilyl-1-propyne) (PTMSP) was studied and analyzed in detail. The gas transport characteristics of dense PTMSP membranes containing 0-10.0 wt % HCPS were studied. It was shown that the introduction of a small amount of HCPS into the PTMSP matrix led to a 50-60% increase of the permeability coefficients of the material for light gases (N₂, O₂, CO₂) and slowed down the deterioration of polymer transport properties over time. The lowest reduction in gas permeability coefficients (50-57%) was found for PTMSP containing HCPS 5.0 wt % after annealing at 100 °C for 300 h. It was found that HCPS sorbed residues of tantalum-based polymerization catalyst from PTMSP. In order to investigate the influence of catalysts on transport and physical properties of PTMSP, we purified the latter from the polymerization catalyst by addition of 5 wt % HCPS into polymer/chloroform solution. It was shown that sorption on HCPS allowed for almost complete removal of tantalum compounds from PTMSP. The membrane made of PTMSP purified by HCPS demonstrated more stable transport characteristics compared to the membrane made of the initial polymer. HCPS has a complex effect on the aging process of PTMSP. The introduction of HCPS into the polymer matrix not only slowed down the physical aging of PTMSP, but also reduced chemical aging due to removal of active reagents.

Polymeric stationary phases for size exclusion chromatography: A review

Synthetic and natural macromolecules are commonly used in a variety of fields such as plastics, nanomedicine, biotherapeutics, drug delivery and tissue engineering. Characterising macromolecules in terms of their structural parameters (size, molar mass and distribution, architecture) is key to have a better understanding of their structure-property relationships. Size exclusion chromatography (SEC) is a commonly used technique for polymer characterization since it offers access to the determination of the size of a macromolecule, its molar mass and the molar mass distribution. Moreover, detectors that allow the determination of true molar masses, macromolecule's architecture and the composition of copolymers can be coupled to the chromatographic system. Like other chromatographic techniques, the stationary phase is of paramount importance for efficient SEC separations. This review presents the basic principles for the design of stationary phases for SEC as well as synthetic methods currently used in the field. Current status of fully-porous polymeric stationary phases used in SEC is reviewed and their advantages and limitations are also discussed. Finally, the potential of polymer monoliths in SEC is also covered, highlighting the limitations this column technology could address. However, further development in the polymer structure is needed to consider this column technology in the field of macromolecule separation.

Control of Physical Aging in Super-Glassy Polymer Mixed Matrix Membranes

ConspectusSince the discovery of polymers of intrinsic microporosity (PIMs) in 2004, the fast size-selective interconnected pore cavities of the polymers have caused the upper bound of membrane performance to be revised, twice. Simultaneously, porous materials have meant that mixed matrix membranes (MMMs) are now a relatively simple method of enhancing transport properties. While there are now reliable routes with mixed matrices to improve the fundamental transport properties of membrane materials, many of the other properties crucial for separation applications remain largely unaddressed. Physical aging severely affects membrane performance over time, especially for those prepared from high fractional free volume polymers. Gradual densification of the glassy polymer chains causes the connected pore channels present in these materials to constrict. Studies now suggest that aging of superglassy polymer materials is a two-step process; a rapid densification occurs within the first few days, followed by a gradual rearrangement of packed chains over longer time frames toward a theoretical equilibrium state. Although advantageous in terms of size selectivity, the considerable drop in permeation over the days and weeks after manufacture greatly impacts material applicability. While often still permeating faster than traditional membrane materials, the continuous gradual collapse of cavities in these polymers are a significant challenge in the application of high free volume polymer membranes. In 2014, we discovered that the porous aromatic framework PAF-1 not only greatly improved the membrane's void space and speed of gas transport but also seemingly froze several glassy polymers in a low-density state, holding the polymer's pore channels open, a process termed as Porosity Induced Side chain Adsorption (PISA).This discovery of PISA fundamentally challenged the conventional wisdom at the time that the aging rate could only be addressed by densification of the polymer. Unlike other high-performance glassy polymers, membranes containing PAF-1 can retain their high permeability for more than a year. Several other examples of antiaging behavior have been subsequently reported by the team, where control of aging rate as a function of gas penetrant, selectivity increases, and stability at higher pressures was reported. These works also demonstrate that these mixed matrix systems had applicability for several other separations, including pervaporation, solvent nanofiltration, and as separators for energy applications. In our subsequent studies, the antiaging mechanism has been elucidated as an effect of the interaction between the polymer's accessible pendant methyl group and the aromatic pore surface of PAF-1 or other antiaging additives. In otherwise identical MMMs, where this hypothesized methyl-π interaction is either absent or interrupted, we find that the antiaging behavior expected by the fixation of the polymer chains to the pore surface and PAF-1 does not occur. As a design approach for mixed matrix membranes, targeted interfacial interactions are a promising pathway for developing other stable membranes, enabling the exciting class of PIM materials to improve industrial separation efficiency.

A self-crosslinking procedure to construct yolk–shell Au@microporous carbon nanospheres for lithium–sulfur batteries

An efficient self-crosslinking procedure to reasonably construct porous shells is reported for the synthesis of yolk–shell Au@microporous carbon nanospheres.

Challenges and Advances in the Fabrication of Monolithic Bioseparation Materials and their Applications in Proteomics Research

High-performance liquid chromatography integrated with tandem mass spectrometry (HPLC-MS/MS) has become a powerful technique for proteomics research. Its performance heavily depends on the separation efficiency of HPLC, which in turn depends on the chromatographic material. As the "heart" of the HPLC system, the chromatographic material is required to achieve excellent column efficiency and fast analysis. Monolithic materials, fabricated as continuous supports with interconnected skeletal structure and flow-through pores, are regarded as an alternative to particle-packed columns. Such materials are featured with easy preparation, fast mass transfer, high porosity, low back pressure, and miniaturization, and are next-generation separation materials for high-throughput proteins and peptides analysis. Herein, the recent progress regarding the fabrication of various monolithic materials is reviewed. Special emphasis is placed on studies of the fabrication of monolithic capillary columns and their applications in separation of biomolecules by capillary liquid chromatography (cLC). The applications of monolithic materials in the digestion, enrichment, and separation of phosphopeptides and glycopeptides from biological samples are also considered. Finally, advances in comprehensive 2D HPLC separations using monolithic columns are also shown.

Hypercrosslinked porous polymer materials: design, synthesis, and applications

Hypercrosslinked polymers (HCPs) are a series of permanent microporous polymer materials initially reported by Davankov, and have received an increasing level of research interest. In recent years, HCPs have experienced rapid growth due to their remarkable advantages such as diverse synthetic methods, easy functionalization, high surface area, low cost reagents and mild operating conditions. Judicious selection of monomers, appropriate length crosslinkers and optimized reaction conditions yielded a well-developed polymer framework with an adjusted porous topology. Post fabrication of the as developed network facilitates the incorporation of various chemical functionalities that may lead to interesting properties and enhance the selection toward a specific application. To date, numerous HCPs have been prepared by post-crosslinking polystyrene-based precursors, one-step self-polycondensation or external crosslinking strategies. The advent of these methodologies has prompted researchers to construct well-defined porous polymer networks with customized micromorphology and functionalities. In this review, we describe not only the basic synthetic principles and strategies of HCPs, but also the advancements in the structural and morphological study as well as the frontiers of potential applications in energy and environmental fields such as gas storage, carbon capture, removal of pollutants, molecular separation, catalysis, drug delivery, sensing etc.

3-Dimensional X-ray microtomography methodology for characterization of monolithic stationary phases and columns for capillary liquid chromatography - A tutorial

In this tutorial we describe a fast, nondestructive, three-dimensional (3-D) view approach to be used in morphology characterization of capillary monoliths and columns by reconstruction from X-ray microtomography (XMT) obtained by acquiring projection images of the sample from a number of different directions. The method comprises imaging acquisition, imaging reconstruction using specific algorithms and imaging analysis by generation of a 3-D image of the sample from radiographic images. The 3-D images show the morphological data for bulk macropore space and skeleton connectivity of the monoliths and were compared with other images from imaging techniques such as scanning electron microscopy (SEM) and field emission scanning electron microscopy (FESEM) and with chromatographic performance. The 3-D XMT methodology is applicable for organic and inorganic capillary chromatographic monolithic materials and it allows the acquisition of many hundreds (in our case 1001 projections) of longitudinal and cross-sectional images in a single session, resolving morphological details with a 3D-view of the monolithic structure, inclusive inside the column in a sectional structure with volume (three dimensions) when compared to the sectional structure area (with only two dimensions) when using SEM and FESEM techniques.

Monolithic stationary phases with a longitudinal gradient of porosity

The duration of the hypercrosslinking reaction has been used to control the extent of small pores formation in polymer-based monolithic stationary phases. Segments of five columns hypercrosslinked for 30-360 min were coupled via zero-volume unions to prepare columns with segmented porosity gradients. The steepness of the porosity gradient affected column efficiency, mass transfer resistance, and separation of both small-molecule alkylbenzenes and high-molar-mass polystyrene standards. In addition, the segmented column with the steepest porosity gradient was prepared as a single column with a continuous porosity gradient. The steepness of porosity gradient in this type column was tuned. Compared to a completely hypercrosslinked column, the column with the shallower gradient produced comparable size-exclusion separation of polystyrene standards but allowed higher column permeability. The completely hypercrosslinked column and the column with porosity gradient were successfully coupled in online two-dimensional liquid chromatography of polymers.

Retention of small molecules on polymethacrylate monolithic capillary columns

In this paper, the concentration of N-isopropylacrylamide in the polymerization mixture has been varied to prepare several polymethacrylate monolithic capillary columns. Polymer monoliths combining N-isopropylacrylamide with zwitterion monomer, as well as various dimethacrylate crosslinking monomers have been prepared and characterized. Uracil, thiourea, phenol, toluene, ethylbenzene, propylbenzene, and butylbenzene have been used to characterize retention of prepared capillary columns in the mobile phases with 40-95% of acetonitrile and at working temperatures ranging from 25 to 60°C. By an optimization of six-parameter polynomial models we have found that the retention of small molecules is affected mainly by the concentration of the acetonitrile in the mobile phase with very low contribution of working temperature and combined effect of acetonitrile concentration and temperature. Concentration of the mobile phase controlled also enthalpy of the retention. On the other hand, entropic contribution was almost insensitive to the change of the mobile phase composition, especially for mobile phases containing more than 60% of acetonitrile.

Advances in organic polymer-based monolithic column technology for high-resolution liquid chromatography-mass spectrometry profiling of antibodies, intact proteins, oligonucleotides, and peptides

This review focuses on the preparation of organic polymer-based monolithic stationary phases and their application in the separation of biomolecules, including antibodies, intact proteins and protein isoforms, oligonucleotides, and protein digests. Column and material properties, and the optimization of the macropore structure towards kinetic performance are also discussed. State-of-the-art liquid chromatography-mass spectrometry biomolecule separations are reviewed and practical aspects such as ion-pairing agent selection and carryover are presented. Finally, advances in comprehensive two-dimensional LC separations using monolithic columns, in particular ion-exchange×reversed-phase and reversed-phase×reversed-phase LC separations conducted at high and low pH, are shown.

Diazoresin modified monodisperse porous poly(glycidylmethacrylate-co-divinylbenzene) microspheres as the stationary phase for high performance liquid chromatography

Diazoresin modified monodisperse porous PGMA–DVB microspheres were used as a novel tool for the separation and purification of the N-vinyl-1,2,4-triazole product from its by-product was developed.

Polystyrene-co-Divinylbenzene PolyHIPE Monoliths in 1.0 mm Column Formats for Liquid Chromatography

The reversed phase liquid chromatographic (RP-HPLC) separation of small molecules using a polystyrene-co-divinylbenzene (PS-co-DVB) polyHIPE stationary phases housed within 1.0 mm i.d. silcosteel columns is presented within this study. A 90% PS-co-DVB polyHIPE was covalently attached to the walls of the column housing by prior wall modification with 3-(trimethoxysilyl) propyl methacrylate and could withstand operating backpressures in excess of 200 bar at a flow rate of 1.2 mL/min. Permeability studies revealed that the monolith swelled slightly in 100% acetonitrile relative to 100% water but could nevertheless be used to separate five alkylbenzenes using a flow rate of 40 µL/min (linear velocity: 0.57 mm/s). Remarkable column-to-column reproducibility is shown with retention factor variation between 2.6% and 6.1% for two separately prepared columns.

Monoliths in capillary electrochromatography and capillary liquid chromatography in conjunction with mass spectrometry

Here, we have reviewed separation studies utilizing monolithic capillary columns for separation of compounds preceding MS analysis. The review is divided in two parts according to the used separation method, namely CEC and capillary LC (cLC). Based on our overview, monolithic CEC-MS technique have been more focused on the syntheses of highly specialized and selective separation phase materials for fast and efficient separation of specific types of analytes. In contrast, monolithic cLC-MS is more widely used and is often employed, for instance, in the analysis of oligonucleotides, metabolites, and peptides and proteins in proteomic studies. While poly(styrene-divinylbenzene)-based and silica-based monolithic capillaries found their place in proteomic analyses, the other laboratory-synthesized monoliths still wait for their wider utilization in routine analyses. The development of new monolithic materials will most likely continue due to the demand of more efficient and rapid separation of increasingly complex samples.