New trends in fast liquid chromatography for food and environmental analysis

Resolving phenylephrine HCl and guaifenesin enantiomers on cellulose-based chiral stationary phases: Separation of four enantiomers on 50-mm column

Chiral high performance liquid chromatographic technique usually employs polysaccharide-based stationary phases in a normal phase mode. This frequently generates large waste of organic solvents. Using shorter columns of 50 mm length as well as a mobile phase with a high water percentage are common approaches for greening this analytical technique. In this context, a new chiral chromatographic technique was developed for simultaneous enantio-separation of phenylephrine HCl and guaifenesin racemates. Four 50 mm cellulose-based columns were experimented to separate the four enantiomers in a reversed phase mode. A face centered design was then employed to optimize the mobile phase acetonitrile% and flow rate on Lux Cellulose-1 (50 × 4.6 mm, 5 μm). The simultaneous resolution of the cited drugs enantiomers was achieved using acetonitrile-water (30:70, by volume), with a flow rate of 0.5 ml min-1 . These optimized chromatographic conditions separate the enantiomers in 7 min running time, generating about 1.0 ml acetonitrile per run. The proposed method was favorably compared with other reported chiral ones in terms of waste volume generated and analysis time required.

A magnetic field augmented ultra-thin layer chromatography coupled surface enhanced Raman spectroscopy separation of hemozoin from bacterial mixture

Malaria is considered as one the most widespread disease with highest possibility of co-infection at all levels of the disease prognosis. Rapid detection and discrimination of malaria from other co-infections remains a challenge. Hemozoin is a metabolic biproduct of malaraia possessing paramagnetic property due to presence of iron at its centre. Here, we report a label free, rapid and highly sensitive magnetic field based ultra-thin layer chromatography (UTLC) coupled with surface enhanced Raman spectroscopy (SERS) technique for detection and separation of hemozoin from a bacterial mixture. Highly optimized silver nanorods chip fabricated using glancing angle deposition (GLAD) is explored for the UTLC-SERS separation. These chips possessing channel like characteristic and high surface to the volume ratio serve as excellent UTLC plates. The magnetic nature of hemozoin has been exploited for its separation from the mixture of P. aeruginosa (Gram-negative) and S. aureus (Gram-positive) by allocating a 0.6 T magnet over the UTLC flow setup. The solvent front migrated approximately to a distance of 13 mm from the sample point due to the magnetic environment. Spatially resolved SERS data was collected along the mobile phase and separation of mixture was confirmed. Further, staining of hemozoin, P. aeruginosa and S. aureus was done using methylene blue, acridine orange and rhodamine 6 G respectively. The separation was confirmed for the stained analytes. The present developed method provides plate height as low as 18 µm and hemozoin detection limit as <10 parasites/mL. Therefore, we establish a highly specific and sensitive technique capable of separating small amounts of bioanalytes, aiding in the removal of co-infections from the disease at a very early stage of infection.

Application of Box-Behnken experimental design and response surface methodology for selecting the optimum RP-HPLC conditions for the simultaneous determination of methocarbamol, indomethacin and betamethasone in their pharmaceutical dosage form

An isocratic RP-HPLC method has been developed for the separation and determination of methocarbamol (MTL), indomethacin (IND), and betamethasone (BET) in combined dosage form using an Inertsil ODS-3v C18 (250 × 4.6 mm, 5 μm) column with UV- detection at 235 nm. Experimental design using Box-Behnken design (BBD) was applied to study the response surface during method optimization and to achieve a good separation with a minimum number of experimental runs. The three independent parameters were pH of buffer, % of acetonitrile and flow rate of the mobile phase while the peak resolution of IND from MTL and the peak resolution of BET from IND (R2) were taken as responses to obtain mathematical models. The composite desirability was employed to optimize a set of responses overall (peak resolutions). The predicted optimum assay conditions include a mobile phase composition of acetonitrile and phosphate buffer (pH 5.95) in a ratio of 79:21, v/v, pumped at a flow rate of 1.4 mL min^-1. With this ideal condition, the optimized method was able to achieve baseline separation of the three drugs with good resolution and a total run time of less than 7 min. The linearity of MTL, IND, and BET was determined in the concentration ranges of 5-600 µg mL^- 1, 5-300 µg mL^- 1, and 5-300 µg mL^- 1 and the regression coefficients were 0.9994, 0.9998, and 0.9998, respectively. The average percent recoveries for the accuracy were determined to be 100.41 ± 0.60%, 100.86 ± 0.86%, and 100.99 ± 0.65% for MTL, IND, and BET, respectively. The R.S.D.% of the intra-day precision was found to be less than 1%, while the R.S.D.% of the inter-day precision was found to be less than 2%. The RP-HPLC method was fully validated with regard to linearity, accuracy, precision, specificity, and robustness as per ICH recommendations. The proposed method has various applications in quality control and routine analysis of the investigated drugs in their pharmaceutical dosage forms and laboratory-prepared mixtures with the goal of reducing laboratory waste, analysis time, and effort.

A simple, rapid, sensitive and eco-friendly LC-MS/MS method for simultaneous determination of free cordycepin and isocordycepin in 10 different kinds of Cordyceps

A simple, rapid, sensitive and eco-friendly liquid chromatography tandem mass spectrometry (LC-MS/MS) method was developed for simultaneous determination of free cordycepin (3′-deoxyadenosine) and isocordycepin (2′-deoxyadenosine) in 10 kinds of Cordyceps samples. The samples were prepared by ultrasonic extraction at 75 °C for 30 min with boiling water as the extraction solvent. The LC separation was performed on an Agilent poroshell 120 SB-Aq C18 column (3.0 × 50 mm, 2.7 μm) in isocratic mode with an eco-friendly mobile phase (2% ethanol containing 0.2% acetic acid) at a flow rate of 0.6 mL min−1, and detected by MS/MS in positive mode with multiple reaction monitoring (MRM). The developed method showed good linearity (r > 0.9990), sensitivity (LODs = 0.04 pg, LOQ = 0.1 pg), precision (RSD ≤ 3.8%) and stability (RSD ≤ 3.6%). The recoveries of developed method were 94.4–109.5% (RSD ≤ 5.5%). Compared with reported methods, the current method was rapid (less than 35% analytical time), sensitive (more than 5 folds), and eco-friendly (less than 10 μL harmful organic solvent). 10 different kinds of Cordyceps samples (40 batches) were tested by the developed method. Codycepin was only found in Cordyceps millitaris and C. millitaris fruiting body, and isocordycepin was detected in Cordyceps sinensis and other 6 Cordyceps samples. The developed method would be an improved method for the quality evaluation of Cordyceps samples.

Functionalized monolithic columns: Recent advancements and their applications for high-efficiency separation and enrichment in food and medicine

The chromatographic column is the core of a high-performance liquid chromatography (HPLC) system, and must have excellent separation efficiency and selectivity. Therefore, functional modification materials for monolithic columns have been rapidly developed. This study is a systematic review of the recently reported functionalized monolithic columns. In particular, the study reviews the types of functional monomers under different modification conditions, as well as the separation and detection techniques combined with chromatography, and their development prospects. In addition, the applications of functionalized monolithic columns in food analysis, biomedicine, and the analysis of active ingredient of Chinese herbal medicines in recent years are also discussed. Also reviewed are the functionalized monolithic columns for qualitative and quantitative analysis. It provided a reference for further development and application of organic polymer monolithic columns.

Study on the Preparation of Estrone Molecularly Imprinted Polymers and Their Application in a Quartz Crystal Microbalance Sensor via a Computer-Assisted Design

Computer simulations are widely used for the selection of conditions for the synthesis of molecularly imprinted polymers and can rapidly reduce the experimental cycle time and save labor and materials. In this paper, estrone molecularly imprinted polymers (E1-MIPs) are designed at the M062X/6-311+G(d,p) level with itaconic acid (IA) as the functional monomer. The imprinted molar ratio between E1 and IA was optimized, cross-linkers and solvents were screened, and the nature of interactions between E1 and IA was explored. The simulated results showed that pentaerythritol triacrylate was the best cross-linker. Meanwhile, when the imprinted molar ratio between E1 and IA was 1:4, the E1–IA complex had the largest amount of hydrogen bonds, the lowest binding energy, and the strongest stability. Using the simulation results as guidance, the E1-MIPs were prepared to modify the electrons of a quartz crystal microbalance (QCM) sensor. The experimental studies showed that the E1-MIPs-QCM sensor had the highest adsorption capacity to E1 in comparison with their analogues, and the lowest detection value of the sensor was 16.00 μg/L. The computer simulations and experimental studies could provide guidance for synthesize novel E1-MIPs materials. It also could provide important references and directions for the application of E1-MIPs.

Effect of grape pomace from red cultivar 'Nero d'Avola' on the microbiological, physicochemical, phenolic profile and sensory aspects of ovine Vastedda-like stretched cheese

AIMS

The purpose of this study was to functionalize an ovine stretched cheese belonging to 'Vastedda' typology with red grape pomace powder (GPP) of Nero d'Avola cultivar and to characterize the microbiological, physicochemical, phenolic profile and sensory characteristics of the final cheeses.

METHODS AND RESULTS

Before cheeses production, GPP was characterized for its microbiological profile, antibacterial activity and polyphenolic content. No colonies of bacteria and yeasts were detected in the GPP. GPP showed a large inhibition spectrum against spoilage and pathogenic bacteria. Three classes of polyphenolic compounds belonging to flavan-3-ols, flavonol and phenolic acids were identified. Two cheeses [0 and 1% (w w^-1 ) of GPP] were produced with pasteurized ewe's milk and commercial starter cultures. Plate counts and randomly amplified polymorphic DNA analysis demonstrated the ability of the starter strains to drive the fermentation process in the presence of GPP. GPP enrichment resulted in an increase of protein, phenolic compounds, sensory traits and reduced fat.

CONCLUSIONS

GPP addition to cheese represents an optimal strategy for the valorization of winemaking by-products and to obtain polyphenol-enriched cheese.

SIGNIFICANCE AND IMPACT OF THE STUDY

This study allowed to achieve an ovine cheese with specific physicochemical, nutraceutical and sensorial characteristics able to enlarge the functional dairy product portfolio.

LC-Q-TOF-MS/MS detection of food flavonoids: principle, methodology, and applications

Flavonoids have been attracting increasing research interest because of their multiple health promoting effects. However, many flavonoids with similar structures are present in foods, often at low concentrations, which increases the difficulty of their separation and identification. Liquid chromatography-quadrupole time-of-flight tandem mass spectrometry (LC-Q-TOF-MS/MS) has become one of the most widely used techniques for flavonoid detection. LC-Q-TOF-MS/MS can achieve highly efficient separation by LC; it also provides structural information regarding flavonoids by Q-TOF-MS/MS. This review presents a comprehensive summary of the scientific principles and detailed methodologies (e.g., qualitative determination, quantitative determination, and data processing) of LC-Q-TOF-MS/MS specifically for food flavonoids. It also discusses the recent applications of LC-Q-TOF-MS/MS in determination of flavonoid types and contents in agricultural products, changes in their structures and contents during food processing, and metabolism in vivo after consumption. Moreover, it proposes necessary technological improvements and potential applications. This review would facilitate the scientific understanding of theory and technique of LC-Q-TOF-MS/MS for flavonoid detection, and promote its applications in food and health industry.

Advances in epitope molecularly imprinted polymers for protein detection: a review

Epitope molecularly imprinted polymers (EMIPs) are novel imprinted materials using short characteristic peptides as templates rather than entire proteins. To be specific, the amino acid sequence of the template peptide is the same as an exposed N- or C-terminus of a target protein, or its amino acid composition and sequence replicate a similar conformational arrangement as the same amino acid residues on the surface of the target protein. EMIPs have a good application prospect in protein research. Herein, we focus on classification of epitope imprinting techniques, methods of epitope immobilization on matrix materials including boronate affinity immobilization, covalent bonding immobilization, physical adsorption immobilization and metal ion chelation immobilization, and application of EMIPs in peptides, proteins, target imaging and target therapy fields. Finally, the main problems and future development are summarized.

Fate and distribution of benzotriazole UV filters and stabilizers in environmental compartments from Gran Canaria Island (Spain): A comparison study

Tourism is an economic sector of great importance worldwide. In coastal areas, this activity is associated with the use of personal care products, such as ultraviolet (UV) filters and stabilizers. Therefore, assessing their presence and the exposure of living organisms to the impact of this kind of pollutant in such areas could be especially important. The Canary Islands (Spain) are considered an outermost region, and their main economic activity is based on tourism, both national and international. Thus, this area could be remarkably vulnerable to this kind of pollution, and its characterization could be useful to infer conclusions for other similar regions. With this aim, the occurrence of organic UV filters and stabilizers in different environmental matrices in Gran Canaria Island is presented in this work. Six benzotriazole compounds, UV-P, UV-326, UV-327, UV-328, UV-329 and UV-360, were found in wastewater, seawater, sludge, sediment, seaweed and fish samples. The numerous studies devoted to establishing the distribution of these target compounds in many different matrices on a touristic and particularly overcrowded island such as Gran Canaria can be used to understand the pollution situation in similar locations. The works in which determination procedures using different extraction techniques were optimized and validated for the analysis of liquid and solid samples are summarized. They are critically discussed regarding their characteristics and analytical parameters. This research is of interest to environmental managers specializing in the conservation of coastal areas where tourism is an important industry since the active components of UV filters and stabilizers can bioaccumulate and biomagnify in the trophic chain.

Facile detection of carbendazim in food using TLC-SERS on diatomite thin layer chromatography

This work aims to isolate and detect pesticide (carbendazim) residue in real food samples: orange juice and kale leaves. The combination of on-chip thin layer chromatography (TLC) and surface enhanced Raman scattering (SERS) spectroscopy was used for the separating and detecting of carbendazim (MBC) from the complex food sample. In order to achieve on-site detection of MBC from real food sample, the portable Raman spectrometer was coupled with TLC-SERS. The porous stationary phase composed of diatomite biosilica is beneficial for SERS enhancement and eluent migration. The experiments exhibited that the diatomite chip was suitable for TLC separation and has not shown SERS background and provided excellent separation efficiency, 10^-8 M silver colloids were appropriate for the SERS measurement on TLC chip. The food sample was directly spotted onto the diatomite chip for TLC separation without any pretreatment. The separation and detection process were finished in less than 5 min, the mixture of pyrimethanil, pymetrozine and MBC could be distinguished simultaneously by TLC-SERS at one diatomite chip. The MBC in orange juice and kale were successfully detected, and a limit of detection (LOD) less than 2 ppm could be achieved.

Ecological and toxicological assessments of anthropogenic contaminants based on environmental metabolomics

There has long been a great concern with growing anthropogenic contaminants and their ecological and toxicological effects on living organisms and the surrounding environment for decades. Metabolomics, a functional readout of cellular activity, can capture organismal responses to various contaminant-related stressors, acquiring direct signatures to illustrate the environmental behaviours of anthropogenic contaminants better. This review entails the application of metabolomics to profile metabolic responses of environmental organisms, e.g. animals (rodents, fish, crustacean and earthworms) and microorganisms (bacteria, yeast and microalgae) to different anthropogenic contaminants, including heavy metals, nanomaterials, pesticides, pharmaceutical and personal products, persistent organic pollutants, and assesses their ecotoxicological impacts with regard to literature published in the recent five years. Contaminant-induced metabolism alteration and up/down-regulation of metabolic pathways are revealed in typical organisms. The obtained insights of variations in global metabolism provide a distinct understanding of how anthropogenic contaminants exert influences on specific metabolic pathways on living organisms. Thus with a novel ecotechnique of environmental metabolomics, risk assessments of anthropogenic contaminants are profoundly demonstrated.

Determination of pyraclostrobin dynamic residual distribution in tilapia tissues by UPLC-MS/MS under acute toxicity conditions

As a lipophilic fungicide, pyraclostrobin is highly toxic to aquatic organisms, especially to fish. In recent years, research has mainly focused on the pyraclostrobin residue in fish tissues under chronic toxicity, but less is known about its distribution in fish tissues under acute toxicity conditions. In this study, the distribution of pyraclostrobin in fish tissues (blood, liver, muscle and gill) was determined by ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The purification effects of different purification materials [1) mixtures of PSA, C₁₈ and MgSO₄; 2) QuEChERS-PC; and 3) Oasis HLB SPE] were compared for the detection of pyraclostrobin in fish tissues. Finally, the quick and easy clean-up tool of the Oasis HLB SPE procedure was selected. Under optimum conditions, the linearities had a good relationship (determination coefficient R² > 0.999). The mean recoveries of the analyte for all tested concentrations ranged from 86.94% to 108.81% with RSDs of 0.7%-4.9%. The pyraclostrobin residue amount was much different in fish tissues. Furthermore, the pyraclostrobin residue in different fish tissues increased initially and then decreased gradually. The concentrations in each tissue were initially ranked before 120 min in the following order: gill > liver > blood > muscle. These phenomena may be attributed to the stress response of fish under acute poisoning. This is the first study to document the distribution of pyraclostrobin in fish tissues under acute toxicity conditions, and it provides reference for the management of agrochemicals in terms of aquatic ecological risks.

Comparison of the Retention and Separation Selectivity of Aromatic Hydrocarbons with Polar Groups in RP-HPLC Systems with Different Stationary Phases and Eluents

In this manuscript, the retention of aromatic hydrocarbons with polar groups has been compared for systems with various nonpolar columns of the types from C3 to C18 and different mobile phases composed of methanol, acetonitrile, or tetrahydrofuran as modifiers. The selectivity separation of the solutes in systems with different adsorbents, when one eluent modifier is swapped by another, has been explained, taking into account molecular interactions of the solutes with components of the stationary phase region (i.e., extracted modifier depending on the chain length of the stationary phase).

Molecularly Imprinted Polymer as Selective Sorbent for the Extraction of Zearalenone in Edible Vegetable Oils

A method based on the selective extraction of zearalenone (ZON) from edible vegetable oils using molecularly imprinted polymer (MIP) has been developed and validated. Ultra-high-pressure liquid chromatography coupled with a fluorescence detection system was employed for the detection of zearalenone. The method was applied to the analysis of zearalenone in maize oil samples spiked at four concentration levels within the maximum permitted amount specified by the European Commission Regulation (EC) No. 1126/2007. As a result, the proposed methodology provided high recoveries (>72%) with good linearity (R2 > 0.999) in the range of 10-2000 μg/kg and a repeatability relative standard deviation below 1.8%. These findings meet the analytical performance criteria specified by the European Commission Regulation No. 401/2006 and reveal that the proposed methodology can be successfully applied for monitoring zearalenone at trace levels in different edible vegetable oils. A comparison of MIP behavior with the ones of QuEChERS and liquid-liquid extraction was also performed, showing higher extraction rates and precision of MIP. Finally, the evolution of ZON contamination during the maize oil refining process was also investigated, demonstrating how the process is unable to completely remove (60%) ZON from oil samples.

Rapid and sensitive detection of mycotoxins by advanced and emerging analytical methods: A review

Quantification of mycotoxins in foodstuffs is extremely difficult as a limited amount of toxins are known to be presented in the food samples. Mycotoxins are secondary toxic metabolites, made primarily by fungal species, contaminating feeds and foods. Due to the presence in globally used grains, it is an unpreventable problem that causes various acute and chronic impacts on human and animal health. Over the previous few years, however, progress has been made in mycotoxin analysis studies. Easier techniques of sample cleanup and advanced chromatographic approaches have been developed, primarily high-performance liquid chromatography. Few extremely sophisticated and adaptable tools such as high-resolution mass spectrometry and gas chromatography-tandem MS/MS have become more important. In addition, Immunoassay, Advanced quantitative techniques are now globally accepted for mycotoxin analysis. Thus, this review summarizes these traditional and highly advance methods and their characteristics for evaluating mycotoxins.

Effect of the Refining Process on Total Hydroxytyrosol, Tyrosol, and Tocopherol Contents of Olive Oil

The impact of the olive oil refining process on major antioxidant compound levels was evaluated by means of UHPLC analysis of lampante olive oils collected at different stages of the refining procedure (degumming, chemical and physical flash neutralization, bleaching, and deodorization). For this purpose, the evolution of the tocopherol fraction was investigated by means of the UHPLC-FL method, while the influence of the refining process on the total hydrolyzed phenolic content was assessed by measuring hydroxytyrosol and tyrosol levels after acid hydrolysis of the phenolic extracts. Refining was found to have a marked effect on total hydroxytyrosol and tyrosol contents, as they are completely removed in the early steps of the refining procedure. In contrast, the variation trends of tocopherols are not always clear-cut, and significant decreases in content from 7% to 16% were only revealed during refining in four out of nine samples. In addition, five of the nine refined oils showed final tocopherol concentrations higher than 200 mg/kg, the limit imposed by international standards regarding the content of such compounds in commercial olive oils. This study supports the need for a revision of the International Olive Oil Council (IOC) standard relative to the limit established for tocopherol addition to refined oils to avoid possible legal and economic trade issues.

Screening 89 Pesticides in Fishery Drugs by Ultrahigh Performance Liquid Chromatography Tandem Quadrupole-Orbitrap Mass Spectrometer

Multiclass screening of drugs with high resolution mass spectrometry is of great interest due to its high time-efficiency and excellent accuracy. A high-scale, fast screening method for pesticides in fishery drugs was established based on ultrahigh performance liquid chromatography tandem quadrupole-Orbitrap high-resolution mass spectrometer. The target compounds - were diluted in methanol and extracted by ultrasonic treatment, and the extracts were diluted with MeOH-water (1:1, v/v) and centrifuged to remove impurities. The chromatographic separation was performed on an Accucore aQ-MS column (100 mm × 2.1 mm, 2.6 μm) with gradient elution using 0.1% formic acid in water (containing 5 mmol/L ammonium formate) and 0.1% formic acid in methanol (containing 5 mmol/L ammonium formate) in Full Scan/dd-MS2 (TopN) scan mode. A screening database, including mass spectrometric and chromatographic information, was established for identification of compounds. The screening detection limits of methods ranged between 1–500 mg/kg, the recoveries of real samples spiked with the concentration of 10 mg/kg and 100 mg/kg standard mixture ranged from 70% to 110% for more than sixty compounds, and the relative standard deviations (RSDs) were less than 20%. The application of this method showed that target pesticides were screened out in 10 samples out of 21 practical samples, in which the banned pesticide chlorpyrifos were detected in 3 out of the 10 samples.

A Comparative Study of Advanced Stationary Phases for Fast Liquid Chromatography Separation of Synthetic Food Colorants

Food analysis demands fast methods for routine control and high throughput of samples. Chromatographic separation enables simultaneous determination of numerous compounds in complex matrices, several approaches increasing separation efficiency and speed of analysis were involved. In this work, modern types of column with monolithic rod or superficially porous particles were employed and compared for determination of eight synthetic food dyes, their chromatographic performance was evaluated. During method optimization, cyano stationary phase Chromolith Performance CN 100 × 4.6 mm and Ascentis Express ES-CN 100 × 4.6 mm, 5 µm were selected for the separation of polar colorants. The separation was performed by gradient elution of acetonitrile/methanol and 2% water solution of ammonium acetate at flow rate 2.0 mL min-1. Mobile phase composition and the gradients were optimized in order to enable efficient separation on both columns. The method using fused-core particle column provided higher separation efficiency, narrow peaks of analytes resulted in increased peak capacity and shortening of analysis time. After the validation, the method was applied for analysis of coloured beers, soft drinks and candies.

Rapid monitoring of plant growth regulators in bean sprouts via automated on-line polymeric monolith solid-phase extraction coupled with liquid chromatography tandem mass spectrometry

An automated on-line solid-phase extraction (SPE) following liquid chromatography tandem mass spectrometry was established for the fast determination of plant growth regulator residues in soybean sprout and mung bean sprout. The crude extracted specimens were directly purified on a poly (2-(dimethylamino) ethyl methacrylate-co-ethylene dimethacrylate) monolithic column which was well-defined as the on-line SPE adsorbent. Under the optimized conditions, the developed method gave the linear range of 0.3-50 ng/mL for gibberellin and 2,4-dichlorophenoxyacetic acid, 0.2-50 ng/mL for 4-chlorophenoxyacetic acid, and 0.5-50 ng/mL for 1-naphthaleneacetic acid (r ≥ 0.998). The detection limits (S/N = 3) ranged from 1.0 to 2.5 μg/kg and the recoveries for spiked soybean sprout samples were in the range of 75.0-93.3%. Besides, the total time for one analysis was 16 min. The reusability of the monolith was up to 600 extractions. The proposed process facilitated fully automated SPE and accurate determination in one step with rapidity, simplicity, and reliability. Graphical abstract ᅟ.

Recent advances of online coupling of sample preparation techniques with ultra high performance liquid chromatography and supercritical fluid chromatography

Ultra high performance liquid chromatography and supercritical fluid chromatography techniques are favored because of their high efficiency and fast analysis speed. Although many sample preparation techniques have been coupled with common liquid chromatography online, the online coupling of sample preparation with the two popular chromatography techniques have gained increasing attention owing to the increasing requirements of efficiency and sensitivity. In this review, we have discussed and summarized the recent advances of the online coupling of sample preparation with ultra high performance liquid chromatography and supercritical fluid chromatography techniques. The main sample preparation techniques that have been coupled with ultra high performance liquid chromatography online are solid-phase extraction and in-tube solid-phase microextraction, while solid-phase extraction and supercritical fluid extraction are the main techniques that have been coupled with supercritical fluid chromatography online. Especially, the strategies for online coupling of sample preparation with chromatography techniques were summarized. Typical applications and growing trends of the online coupling techniques were also discussed in detail. With the increasing demands of improving the efficiency, throughput, and analytical capability toward complex samples of the analysis methods, online coupling of sample preparation with chromatography techniques will acquire further development.

Multiclass screening of >200 pharmaceutical and other residues in aquatic foods by ultrahigh-performance liquid chromatography-quadrupole-Orbitrap mass spectrometry

A quick screening method of more than 200 pharmaceutical and other residues in aquatic foods based on ultrahigh-performance liquid chromatography-quadrupole-Orbitrap mass spectrometry (UHPLC-Q/Orbitrap MS) was established. In this method, after the addition of 200 μL of 1 M EDTA-Na₂, 2 g of each sample homogenate was extracted successively with 10 mL of acetonitrile and 10 mL of ethyl acetate. The extracts were combined, dried under nitrogen flow, and redissolved in 0.1% formic acid in acetonitrile/water (4:6, v/v) for analysis. The prepared samples were analyzed by UHPLC- Q/Orbitrap MS system in Full MS/ddMS² (full-scan data-dependent MS/MS) mode. Compound identification was performed through comparison of the sample data with the database for standard chemicals, including the retention time, precursor ion, product ions, and isotope pattern for all 206 compounds. Five different aquatic food matrices (carp, shrimp, crab, eel, and mussel) spiked with the analytes at 1, 10, and 50 ng/g were evaluated to assess recoveries, precision, matrix effects, stability, and detection limits using the method. UHPLC analyses required 25 min, and 178-200 analytes met identification criteria at 50 ng/g depending on the matrix. Furthermore, practical application of this method for real samples displayed strong screening capability. Graphical abstract A quick screening method of >200 pharmaceutical and other residues in aquatic foods based on ultrahighperformance liquid chromatography-quadrupole-Orbitrap mass spectrometer was established. Fivedifferent aquatic food matrices, including carp, shrimp, crab, eel and mussel, were studied to evaluatescreen limit at 1, 10 and 50 μg·kg-1 level. Results suggest the high reliability, high time-efficiency and goodsimplicity of the method.

Chemometric and high-resolution mass spectrometry tools for the characterization and comparison of raw and treated wastewater samples of a pilot plant on the SIPIBEL site

Due to its key role in the contamination of natural resources, the assessment of raw and treated wastewater effluents is a current major concern and urges comprehensive analytical methods capable of selectively capturing the chemodiversity of these samples. In this context, the overall objective of this work can be summarized as (i) the assessment of the performance of secondary and tertiary (advanced oxidation) wastewater treatments through multivariate analysis followed by (ii) the comprehensive characterization of wastewater samples based on their spectral fingerprints and a combination of suspect and non-target screening approaches. Several compounds, belonging to different sources of contamination were annotated and/or partially identified: pharmaceuticals, metabolites and transformation compounds, human activity markers, surfactants, and polyethoxy compounds. These results highlight the contribution of filtering and screening tools such as monoisotopic exact mass, mass defect, MS/MS data-dependent acquisitions, isotopic pattern and retention time to the selection, and the identification of environmental contaminants and their metabolites/degradation products. This paper completes the target study conducted in the SIPIBEL site and offers an alternative for the assessment of treatment processes by broadening the spectrum to a larger number of compounds and the correlations between them.

A QuEChERS-Based Liquid Chromatography-Tandem Mass Spectrometry Method for the Simultaneous Determination of Nine Zearalenone-Like Mycotoxins in Pigs

The determination of zearalenone (ZEN) and its derivatives as biomarkers in animal tissues or organs plays an important role in mycotoxin monitoring and can promote effective exposure assessment. A liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for the simultaneous quantification of nine ZEN-like mycotoxins, including three glucuronides in different pig tissues (heart, liver, spleen and muscle) was developed and validated in this study. Tissue samples were extracted using a quick, easy, cheap, effective, rugged, and safe (QuEChERS) extraction and clean-up procedure, and analyzed by LC-MS/MS in multiple reaction monitoring (MRM) mode. Dynamic linear ranges for each target analyte were determined with R² between 0.916 and 0.999. The LODs of the six ZENs were achieved in the range of 0.5-1 ng/g and the LOQs varied from 1 ng/g to 2 ng/g. The satisfying intra-day and inter-day reproducibility (both RSDr and RSDR < 20%) indicated a good stability of this method. The recoveries of the nine target analytes were in the range of 70-110%. The validation results showed that this LC-MS/MS method coupled with QuEChERS sample pretreatment is effective and suitable for the simultaneous quantitation of ZEN metabolites in pigs. It has been applied to analysis of the pig tissues in this research and can be also adapted for samples in the mycotoxin research field.

Molecularly Imprinted Polymers as Extracting Media for the Chromatographic Determination of Antibiotics in Milk

Milk-producing animals are typically kept stationary in overcrowded large-scale farms and in most cases under unsanitary conditions, which promotes the development of infections. In order to maintain sufficient health status among the herd or promote growth and increase production, farmers administer preventative antibiotic doses to the animals through their feed. However, many antibiotics used in cattle farms are intended for the treatment of bacterial infections in humans. This results in the development of antibiotic-resistant bacteria which pose a great risk for public health. Additionally, antibiotic residues are found in milk and dairy products, with potential toxic effects for the consumers. Hence the need of antibiotic residues monitoring in milk arises. Analytical methods were developed for the determination of antibiotics in milk, with key priority given to the analyte extraction and preconcentration step. Extraction can benefit from the production of molecularly imprinted polymers (MIPs) that can be applied as sorbents for the extraction of specific antibiotics. This review focuses on the principals of molecular imprinting technology and synthesis methods of MIPs, as well as the application of MIPs and MIPs composites for the chromatographic determination of various antibiotic categories in milk found in the recent literature.

Hydrophilic interaction liquid chromatography tandem mass spectrometry analysis of malonyl-coenzyme A in breast cancer cell cultures applying online solid-phase extraction

Cofactors such as coenzyme A and its derivatives acetyl-coenzyme A and malonyl-coenzyme A are involved in many metabolic pathways. Due to trace level concentrations in biological samples and the high reactivity of cofactors, a fast, sensitive, and selective method for quantification is mandatory. In this study, online solid-phase extraction was coupled successfully to hydrophilic interaction liquid chromatography with tandem mass spectrometry for isolation of analytes in complex matrix and quantification by external calibration. Online solid-phase extraction was carried out by application of a weak anion-exchange column, whereas hydrophilic interaction liquid chromatography separation was performed on an amide modified stationary phase. Sample preparation of the extracts before the analysis was reduced to a centrifugation and dilution step. Moreover, the applied online solid-phase extraction significantly reduced matrix effects and increased the signal-to-noise ratio. The limit of detection and the limit of quantification were in the lower nanomolar range. Finally, the applicability of this method was demonstrated on MCF-7 breast cancer cell cultures, a commonly used model system, where acetyl-coenzyme A and malonyl-coenzyme A were determined using standard addition procedure in concentrations of 1.98 μM and 41 nM, respectively.

Determination of bisphenols with estrogenic activity in plastic packaged baby food samples using solid-liquid extraction and clean-up with dispersive sorbents followed by gas chromatography tandem mass spectrometry analysis

Bisphenols (BPs) are a family of chemicals with known endocrine disrupting activity. Bisphenol A (BPA) is the most representative prototype of this group of chemicals. Recently, the use of BPA, a prototype of endocrine disruptors, has been reduced and replaced with structural analogs due to its negative effects on both the environment and consumers. In this work, a new method is presented for the determination of seven BPs, with estrogenic activity in ready-to-eat plastic packaged baby foods. The procedure involves the isolation of the analytes using solid-liquid phase extraction with acetonitrile followed by a clean-up step with a mixture of dispersive-SPE sorbents (C18 and PSA) and magnesium sulphate, to reduce matrix effect from proteins, sugars and lipids. Extraction parameters were optimized using multivariate optimization methods. The compounds were detected and quantified by gas chromatography tandem mass spectrometry (GC-MS/MS). The limits of quantification were between 0.1 and 1.2ngg^-1 for the studied analytes. The method was validated using matrix-matched calibration and recovery assays with spiked samples. Recovery rates were between 91% and 110% and % RSD was lower than 13% in all cases. The method has been successfully applied for the determination of these endocrine disrupting chemicals (EDCs) in samples of a novel type of food consumed by pre-schoolers. This is the first study to analyze EDCs in plastic packaged foods consumed by this target group.