Potential of hydrophobic paper-based sorptive phase prepared by in-situ thermal imidization for the extraction of methadone from oral fluid samples

Nylon 6-cellulose composite hosted in a hypodermic needle: Biofluid extraction and analysis by ambient mass spectrometry in a single device

This study proposes a hypodermic needle (HN) as a sorbent holder and an electrospray (ESI) emitter, thus combining extraction and analysis in a single device. A novel nylon 6-cellulose (N6-Cel) composite sorbent is proposed to extract methadone from oral fluid samples. The cellulosic substrate provides the composite with high porosity, permitting the flow-through of the sample, while the polyamide contributes to the extraction of the analyte. The low price of the devices (considering the holder and the sorbent) contributes to the affordability of the method, and their small size allows easy transportation, opening the door to on-site extractions. Under the optimum conditions, the analyte can be determined by high-resolution ambient ionization mass spectrometry at a limit of detection (LOD) as low as 0.3 μg/L and precision (expressed as relative standard deviation, RSD) better than 9.3%. The trueness, expressed as relative recovery (RR), ranged from 90% to 109%. As high-resolution mass spectrometers are not available in many laboratories, the method was also adapted to low-resolution spectrometers. In this sense, the direct infusion of the eluates in a triple quadrupole-mass spectrometry provided an LOD of 2.2 μg/L. The RSD was better than 5.3%, and the RR ranged from 96% to 121%.

Mixed-mode cationic exchange sorptive tapes combined with direct infusion mass spectrometry for determining opioids in saliva samples

This article describes the synthesis of mixed-mode cationic exchange (MCX) tapes as sorptive phases in bioanalysis, and it faces the determination of methadone and tramadol in saliva as the model analytical problem. The tapes are synthesized using aluminum foil as substrate, which is subsequently covered with double-sided adhesive tape where the MCX particles (ca. 1.4 ± 0.2 mg) finally adhere. MCX particles allow the extraction of the analytes at the physiological pH, where both drugs are positively charged, minimizing the potential co-extraction of endogenous matrix compounds. The extraction conditions were studied considering the main variables (e.g. ionic strength, extraction time, sample dilution). Under the optimum conditions and using direct infusion mass spectrometry as the instrumental technique, detection limits as low as 3.3 μg·L^-1 were obtained. The precision calculated at three different levels, and expressed as relative standard deviation, was better than 3.8%. The accuracy, expressed as relative recoveries, ranged from 83 to 113%. The method was finally applied to determine tramadol in saliva samples from patients under medical treatment. This approach opens the door to easily preparing sorptive tapes based on commercial (or ad-hoc synthesized) sorbent particles.

Innovative, simple, and green: A sample preparation method based on 3D printed polymers

The present study evaluates the capability of fifteen 3D printed thermoplastic polymers as novel stationary phases for the extraction of forty-three physicochemically diverse analytes from fortified human oral fluid samples. Prototype extraction devices were prepared in 96-well plate-compatible format using fused deposition modeling 3D printer. The sample preparation was performed with 5-step protocol utilizing 96-well plates and semiautomated benchtop shaker. All resulting extracts were analyzed via high-performance liquid chromatography (operated in reversed-phase gradient elution mode) and tandem mass spectrometry (with electrospray ionization and triple quadrupole mass spectrometer). Exceptionally favorable results were observed for three polymer types: polyamide 6 (reinforced with 15% carbon fiber), LAYFOMM-60 (polyurethane with water-soluble polyvinyl alcohol), and S-FLEX 90A (thermoplastic polyurethane). Furthermore, this study also introduces an automated and repeatable 3D printing method for the fast fabrication of high-throughput, and highly selective sample preparation devices, most of which are ready-to-use without any additional processing or chemical functionalization. As such, the proposed printing method represents a significant step towards the introduction of novel polymeric stationary phases for analytical sample preparation, thus providing laboratory personnel with a method that is safer and more convenient, while minimizing negative environmental impacts.