A biomechanical study on the laminate stacking sequence in composite bone plates for vancouver femur B1 fracture fixation

Effect of matrix material property on the composite tibia fracture plate: a biomechanical study

For the purpose of fixing tibia fractures, composite bone plates are suggested. Metal plates cause stress shielding, lessen the compression force at the fracture site, and have an impact on the healing process because they are significantly more rigid than bone. To prevent excessive shear strain and consequent instability at the fracture site, it is imperative to reduce stiffness in the axial direction without lowering stiffness in the transverse direction. Only a carefully crafted fiber reinforced composite with anisotropic properties will suffice to accomplish this. The purpose of the current study is to examine the impact of axial and shear movements at the fracture site on the fixing of metal and composite bone plates. After modeling the tibia with a 1 mm fracture gap, titanium plates, carbon/epoxy, carbon/PEEK, and carbon/UHMWPE composite bone plates were used to fix it. There are 6 holes on each of the 103 mm long plates. To determine the stresses and axial movement in the fracture site, anatomical 3D Finite Element (FE) models of the tibia with composite bone plates are built. The simulations that were run for various composite plate layouts and types give suggestions for selecting the best composite bone plate. Although the matrix material causes some variations in behaviors, most of the plates perform as well as or even better than metal plates. Thus, the appropriate composite combinations are recommended for a given fracture structure.

Effect of different composite plates on the healing of femoral fractures

In this paper, the effects of different composite plates on the healing of femoral fractures were studied by numerical simulation. The healing model of femoral fracture was established by ABAQUS display solver. Based on the fuzzy logic theory, the process of callus differentiation at femoral fracture was considered under the joint action of biological variables and mechanical stimulation, and the healing process of femur was simulated. Compare the stress on the screw, concentration of callus bone and cartilage, and callus healing performance of the carbon/epoxy composite (WSN3k) plate, glass/polypropylene composite (Twintex) plate, and stainless steel plate at various stages of bone healing, and investigate the impact of composite plates on the bone healing process. The results showed that the modulus of the plate had a notable impact on bone healing. Compared to stainless steel plate, the composite plate (due to its lower stiffness) exhibiting superior healing performance. Altering the sequence of composite laminates may modify the bone healing efficiency, and the wsn3k [0]18 composite plate exhibits superior healing performance.

The influence of composite bone plates in Vancouver femur B1 fracture fixation after post-operative, and healed bone stages: A finite element study

Conventional stainless steel or titanium plates are used for bone fracture fixation to provide support at fracture location. Plates with high elastic modulus reduce the transfer of compressive load at the fracture location (due to stress shielding), causing failure. The objective of the study is to find for composite bone plates with different types of fibers and varied fiber orientations for post-operative (PO) and healed bone (HB) conditions which can reduce the stress shielding. Femur fracture fixation was constructed with 12 holes narrow type with metal and composite bone plates. The fracture gap was constructed with soft bone region for post-operative (PO) condition and harder bone for healed bone (HB). Composite bone plates with different configurations (fiber directions) and types (thickness and width) were analyzed to study the stress distribution and movement in the fracture location. The models were analyzed and the stresses in plate and callus, movement and strain in axial and shear direction in both metal and composite bone plates were studied. The metal and composite plates (carbon fiber/epoxy, fiberglass/epoxy, and flax/epoxy) used for most common Vancouver type B1 fracture to observe the biomechanical behavior of different models in PO and HB condition. The FE simulation on different configurations and types of composite plates provide in-depth idea about choosing the suitable composite bone plate. There are variations in behavior for varying types and configurations, but the performance of most of the plates are either better or similar to that of metal plate, except the plates with higher width.

Plate configuration for biological reconstructions of femoral intercalary defect - a finite element evaluation

BACKGROUND AND OBJECTIVE

Biological reconstruction was commonly used for femoral intercalary defect. The initial stability by plate fixation was believed to have an effect on bone union and implant failure. Our study was proposed to explore relationship of plate configuration and initial stability for femoral intercalary reconstruction using allo-/autograft.

METHODS

Femoral intercalary defect models were established with four different plate configurations: (1) Single lateral bridging plate, SLP (2) Lateral bridging plate + Orthogonal adjuvant plate, LP+OAP (3) Lateral bridging plate + Medial adjuvant plate, LP+MAP (4) Lateral bridging plate + Medial bridging plate, LP+MP. A diaphysis defect of 12 cm was simulated, and the removed native femoral bone was used as a structural allograft with the osteotomy gap of 2 mm. Models were analyzed by finite element simulations under an axial compression of 2000N and an axial moment of 10 Nm, respectively.

RESULTS

Axial load: (1) The peak von Mises stress of SLP, LP+OAP, LP+MAP, LP+MP were 993.50 MPa, 335.63 MPa, 240.03 MPa, 281.73 MPa, respectively and LP+MAP was the lowest (p < 0.01); (2) The mean displacement of SLP, LP+OAP, LP+MAP, LP+MP was 0.765, 0.130, 0.121, 0.235 mm, respectively. LP+MAP showed the best stability while SLP had a crash in the medial proximal gap; (3) The LP+MAP configuration had the most uniform stress distribution and the lowest maximum von Mises stress of 79.7 MPa within plates. Axial torsional load: (1) The peak von Mises stress of SLP, LP+OAP, LP+MAP, LP+MP were 431.66Mpa, 120.73 MPa, 72.31 MPa, 109.86 MPa, respectively; (2) The rotation angle of SLP, LP+OAP, LP+MAP, LP+MP was 4.30°, 1.35°, 1.20°, 1.57°, respectively. All of LP+OAP, LP+MAP and LP+MP showed an optimal torsional stability.

CONCLUSIONS

For femoral intercalary reconstruction using allo-/autograft fixed by plates, LP+MAP and LP+MP configurations showed superior stability in terms of axial compression and torsion load by FE simulation. A better stability was believed to be associated with higher union rate and lower hardware failure rate.

Finite element analysis of intraosseous distal radioulnar joint prosthesis

BACKGROUND

Joint replacement is one of the options to retrieve the interosseous distal radioulnar joint (DRUJ) function. DRUJ prosthesis has recently been introduced clinically to treat DRUJ instability. This article analyzes the biomechanical behavior of the prosthesis during different loadings by the finite element method.

METHODS

CT images of a healthy 33 years old man were used to construct the three-dimensional geometry of the forearm bone. Then two models, a healthy foreman (Model A) and a damaged model with an inserted interosseous prosthesis (Model B), were constructed to analyze and compare the foreman's biomechanical behavior under different loading conditions using the finite element method. Both models were examined during pronation and supination with 500, 1000, 2000, and 5000 N.mm values. Also, both models were subjected to volar and dorsal loads with values of 10, 30, and 50 N and traction force with 100, 150, and 200 N.

RESULTS

Maximum and minimum principal stresses were evaluated for bones in all conditions, and von Mises stress was considered for the prosthesis and fixing screws. In supination, the maximum stress in Model A is significantly higher than the Model B. However, the maximum principal stress of both models is similar during volar and dorsal loading. In Model A, the maximum principal stress in traction is much smaller than in Model B. The absolute value of minimum principal stress in pronation and supination in Model B is higher than in Model A. The prostheses and screws are subjected to higher stresses during pronation than supination. Also, the amount of stress created in prostheses and screws during volar and dorsal loading is almost equal. In traction loading, screws are subjected to significantly high stresses.

CONCLUSION

Our study indicates that the interosseous DRUJ prosthesis can perform the foreman's normal daily activities. This prosthesis provides the ability similar to a normal hand.

LEVEL OF EVIDENCE

IV.

The influence of the viscoelastic property of polycarbonate urethane as an artificial disc core material under various physiological motions at the L4-L5 level

Intervertebral disc (IVD) degeneration is one of the musculoskeletal disorders due to the Degenerative Disc Disease (DDD), that cause low back pain (LBP) and leads to a reduced range of motion. Spinal fusion and arthroplasty are the other surgical procedures that could replace the disc affected by DDD against artificial disc replacement (ADR). This study aims to analyse the biomechanical behaviour of proposed core material as Polycarbonate Urethane (PCU) in the L4-L5 lumbar segment for ADR with Ti-6Al-4V and Co-28Cr-6M as endplate materials and compare it to the performance of an ultra-high molecular weight polyethylene (UHMWPE) core. Finite element methods have been approached to measure the overall stress distribution along with other physiological motions like Flexion (FLEX), Extension (EXT), Axial rotation (AR) and Lateral bending (LB), respectively. Preload of 450 N compressive load, 8 N-m for Flex, 6 N-m for EXT, 6 N-m for AR and 4 N-m for LB are applied. It could be concluded that Ti-6Al-4V - PCU and Co-28Cr-6M - PCU is the best composition for the ADR for the L4-L5 level.

Metal and composite bone plates for B1 periprosthetic femoral fracture in healthy and osteoporotic condition: A comparative biomechanical study

The major concern after total hip arthroplasty (THA) is the incidence of periprosthetic fracture in the weaker bone, which can lead to subsequent revision surgery. Achieving the suitable fixation without affecting the stability of the well-fixed prosthesis remains controversial. Most of the studies examined the behavior of the Periprosthetic Fracture (PF) fixation (Vancouver “B1” type) through computational and experimentation on healthy bone condition with metal plates. The aim of the present study is to analyze the influences of the metal and composite bone plate PF fixation on the axial and shear movement at the fracture site. The PF fixation constructs were modeled with medical graded stainless-steel plate (construct A), titanium plate (construct B) and carbon/epoxy composite bone plate (construct C) with 12 holes and a 4 mm fracture gap. Analysis was carried out for all the stages (stage 1—Normal bone, stage 2—THA, stage 3—Immediate Post-Operative (IPO), stage 4—Post-Operative (PO) and, stage 5—Healed Bone (HB)) under various loadings for intact and osteoporosis conditions. The results showed higher stress in cortical bone for stage 3, whereas in all the other stages lower stresses were experienced in the cortical and cancelous bone under peak load in construct C for osteoporosis model compared with other constructs. The present study suggested the construct C may be suitable for osteoporosis bone conditions.

The race for the classification of proximal periprosthetic femoral fractures : Vancouver vs Unified Classification System (UCS) - a systematic review

Background

Periprosthetic femoral fractures (PFFs) represent a major cause for surgical revision after hip arthroplasty with detrimental consequences for patients. The Vancouver classification has been traditionally used since its introduction in 1995. The Unified Classification System (UCS) was described in 2014, to widen the spectrum by aiming for a more comprehensive approach. The UCS also aimed to replace the Vancouver classification by expanding the idea of the Vancouver classification to the whole musculoskeletal apparatus. After introduction of the UCS, the question was raised, whether the UCS found its place in the field of analysing PFFs. Therefore, this systematic review was performed to investigate, the use of the UCS compared to the established Vancouver classification.

Methods

Medline was searched for reports published between 1 January 2016 and 31 November 2020, without language restriction. Included were original articles, irrespective of the level of evidence and case reports reporting on a PFF and using either the Vancouver or the UCS to classify the fractures. Excluded were reviews and systematic reviews.

Results

One hundred forty-six studies were included in the analysis. UCS has not been used in a single registry study, giving a pooled cohort size of 3299 patients, compared to 59,178 patients in studies using the Vancouver classification. Since 2016, one study using UCS was published in a top journal, compared to 37 studies using the Vancouver classification (p=0.29). During the study period, the number of yearly publications remained stagnant (p=0.899).

Conclusions

Despite valuable improvement and expansion of the latter UCS, to date, the Vancouver system clearly leads the field of classifying PFFs in the sense of the common use.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12891-022-05240-w.

Simplified Mechanical Tests Can Simulate Physiological Mechanics of a Fixation Construct for Periprosthetic Femoral Fractures

Plate fractures after fixation of a Vancouver Type B1 periprosthetic femoral fracture (PFF) are difficult to treat and could lead to severe disability. However, due to the lack of direct measurement of in vivo performance of the PFF fixation construct, it is unknown whether current standard mechanical tests or previous experimental and computational studies have appropriately reproduced the in vivo mechanics of the plate. To provide a basis for the evaluation and development of appropriate mechanical tests for assessment of plate fracture risk, this study applied loads of common activities of daily living (ADLs) to implanted femur finite element (FE) models with PFF fixation constructs with an existing or a healed PFF. Based on FE simulated plate mechanics, the standard four-point-bend test adequately matched the stress state and the resultant bending moment in the plate as compared with femur models with an existing PFF. In addition, the newly developed constrained three-point-bend tests were able to reproduce plate stresses in models with a healed PFF. Furthermore, a combined bending and compression cadaveric test was appropriate for risk assessment including both plate fracture and screw loosening after the complete healing of PFF. The result of this study provides the means for combined experimental and computational preclinical evaluation of PFF fixation constructs.