Recent advances in the application of cellulose nanocrystals

Cellulose nanocrystals (CNCs) with different degrees of amination to enhance tolerance to Fe (III) and enhance oil displacement performance

Cellulose nanocrystals (CNCs) have been widely concerned in enhanced oil recovery (EOR) due to their abundant resources, small size and easy modification. In crude oil extraction, Fe (III) is increasingly produced. However, CNCs are very sensitive to Fe (III) and easy to aggregate, which brings obstacles to the application of CNCs. In order to improve the tolerance of CNCs to Fe (III), the surface of CNCs was modified with Aminopropyltrimethoxysilane (APTMS), N-[3-Trimethoxysilyl)propyl]ethylenediamine (TMPED) and N-[3-(trimeth-oxysilyl)propyl]diethylenetriamine (TMPDET), respectively. The products were named CNC-APTMS, CNC-TMPED and CNC-TMPDET. The N content in CNC-APTMS, CNC-TMPED and CNC-TMPDET are 1.36 wt%, 2.03 wt% and 2.17 wt%, respectively. The adsorption amount of Fe (III) by CNCs, CNC-APTMS, CNC-TMPED and CNC-TMPDETDT are ~155 mg/g, ~ 13 mg/g, ~ 29 mg/g and ~ 18 mg/g, respectively. This indicates that compared to CNCs, the modified CNCs improve significantly the tolerance to Fe (III). Moreover, compared to CNCs, in the presence of Fe (III), there is less remaining oil in the glass model after modified CNCs dispersion flooding. The improvement of tolerance to Fe (III) and the excellent oil displacement performance of the modified CNCs in the presence of Fe (III) make them the potential green oil displacement agents.

Cellulose nano-dispersions enhanced by ultrasound assisted chemical modification drive osteoblast proliferation and differentiation in PVA/HA bone tissue engineering scaffolds

To develop a biological bone tissue scaffold with uniform pore size and good cell adhesion was both challenging and imperative. We prepared modified cellulose nanocrystals (CNCs) dispersants (K-PCNCs) by ultrasound-assisted alkylation modification. Subsequently, nano-hydroxyapatite (HC-K) was synthesized using K-PCNCs as a dispersant and composited with polyvinyl alcohol (PVA) to prepare the scaffold using the ice template method. The results showed that the water contact angle and degree of substitution (135°, 1.53) of the K-PCNCs were highest when the ultrasound power was 450 W and the time was 2 h. The dispersion of K-PCNCs prepared under this condition was optimal. SEM showed that the pore distribution of the composite scaffolds was more homogeneous than the PVA scaffold. The porosity, equilibrium swelling rate, and mechanical properties of the composite scaffolds increased and then decreased with the increase of HC-K content, and reached the maximum values (56.1 %, 807.7 %, and 0.085 ± 0.004 MPa) at 9 % (w/w) of HC-K content. Cell experiments confirmed scaffold has good cytocompatibility and mineralization capacity. The ALP activity reached 1.71 ± 0.25 (ALP activity/mg protein). In conclusion, the scaffolds we developed have good biocompatibility and mechanical properties and have great potential in promoting bone defect repair.

Surface modification of cellulose nanocrystals for biomedical and personal hygiene applications

The increasing demand for sustainable and effective materials in biomedical and personal hygiene applications has driven the exploration of cellulose nanocrystals (CNCs) derived from biomass. These nanomaterials are highly valued for their exceptional mechanical properties, biocompatibility, and renewable nature. Researchers are exploring CNCs for advancing medical and hygiene products, but surface modification is often needed to maximize their benefits. Techniques such as chemical functionalization, physical coating, and hybridization can significantly enhance CNCs dispersibility, stability, and interaction with biological systems. This versatility makes CNCs suitable for a variety of applications, including drug delivery systems, wound dressings, and personal hygiene products. Despite their advantages, maintaining the inherent properties of CNCs while integrating new functionalities through modification poses a challenge. Understanding the impact of various modification techniques on CNC performance is crucial for optimizing their effectiveness. This review aimed to consolidate current knowledge on the surface modification of biomass-derived CNCs, offering insights into different methods and their implications for biomedical and personal hygiene applications. By highlighting advancements, challenges, and prospects, it served as a crucial resource for advancing the development and application of CNCs in these critical fields.

Wetting and emulsification properties of cellulose nanocrystals modified with tannic acid and alkyl cellulose derivatives

HYPOTHESIS

Cellulose nanocrystals (CNCs) are sustainable rod-like nanoparticles that can be used to stabilize oil-in-water emulsions and can create hydrophilic coatings. Modifying the surface of CNCs can improve emulsion properties and allow for adjustable wettability.

EXPERIMENTS

This study explores the improvement of Pickering emulsion properties for various oils and the adjustability of coated surfaces through the physical modification of CNCs, without chemical functionalization. Bio-based additives, including antioxidant tannic acid (TA), methyl cellulose (MC), and ethyl cellulose (EC) were used as surface modifiers. The identification of optimal formulations involved varying the weight fraction of the alkyl cellulose derivatives.

FINDINGS

The findings suggest that, akin to pure CNCs, Pickering emulsions stabilized by TA and/or MC-modified CNCs demonstrate comparably high stability. The introduction of MC at a low weight fraction enhances hydrophilicity, and AFM analysis reveals smooth surfaces, mitigating the potential influence of roughness. In contrast, EC-modified CNCs result in less stable emulsions but exhibit more hydrophobic surfaces. This translates to a broad spectrum of characteristics, ranging from quasi-superhydrophilic to nearly hydrophobic (with contact angles spanning from below 11° up to 68°), all controllable through a straightforward physical coating process. This facile preparation of coated CNCs provides a versatile approach to customizing the wetting and emulsification properties of nanomaterials.

Cellulose nanomaterial metrology: microscopy measurements

Cellulose nanomaterials are increasingly used for a wide variety of applications. Adequate characterization of these materials is required for quality control during production, to distinguish between materials synthesized by different methods, by different suppliers or from difference cellulose biomass sources, to facilitate development of applications and for regulatory purposes. Here we review recent microscopy measurements for the three main types of cellulose nanomaterials: cellulose nanocrystals, individual cellulose nanofibrils and cellulose nanofibrils. Atomic force microscopy and both scanning and transmission electron microscopy are covered with a focus on recent studies that have metrological rigor, rather than qualitative investigations. In some cases results are compared to those obtained by other methods that are more likely to see widespread use for routine quality control measurements. Detailed studies that use microscopy to provide insight on fundamental material properties (e.g., chiral properties) are also included. Particle size and morphology are important properties but are challenging to measure for cellulose nanomaterials due to the rod or fibril shaped particles, their propensity to agglomerate and aggregate, their low contrast for electron microscopy and, for cellulose nanofibrils, the complex branched and interconnected structures. Overall, the results show that there are now a number of studies in which attention to metrological detail has resulted in measurements that allow one to compare and distinguish between different materials, although there are still examples for which it is not possible to draw conclusions on size differences. The use of detailed microscopy protocols that yield accurate and reliable results will be beneficial in material production and addressing regulatory requirements and will allow the validation of other methods that are more amenable to routine measurements.

Cellulose derivatives as environmentally-friendly additives in water-based drilling fluids: A review

The application of cellulose derivatives including carboxymethyl cellulose (CMC), polyanionic cellulose (PAC), hydroxyethyl cellulose (HEC), cellulose nanofibrils (CNFs), and cellulose nanocrystals (CNCs) has gained enormous interest, especially as environmentally friendly additives for water-based drilling fluids (WBDFs). This is due to their sustainable, biodegradable, and biocompatible nature. Furthermore, cellulose nanomaterials (CNMs), which include both CNFs and CNCs, possess unique properties such as nanoscale dimensions, a large surface area, as well as unique mechanical, thermal, and rheological performance that makes them stand out as compared to other additives used in WBDFs. The high surface hydration capacity, strong interaction with bentonite, and the presence of a complex network within the structure of CNMs enable them to act as efficient rheological modifiers in WBDFs. Moreover, the nano-size dimension and facilely tunable surface chemistry of CNMs make them suitable as effective fluid loss reducers as well as shale inhibitors as they have the ability to penetrate, absorb, and plug the nanopores within the exposed formation and prevent further penetration of water into the formation. This review provides an overview of recent progress in the application of cellulose derivatives, including CMC, PAC, HEC, CNFs, and CNCs, as additives in WBDFs. It begins with a discussion of the structure and synthesis of cellulose derivatives, followed by their specific application as rheological, fluid loss reducer, and shale inhibition additives in WBDFs. Finally, the challenges and future perspectives are outlined to guide further research and development in the effective utilization of cellulose derivatives as additives in WBDFs.

Carboxymethyl chitosan and dialdehyde cellulose nanocrystal based injectable self-healing emulsion gel

The study aims to demonstrate a general method for producing emulsion gels with self-healing properties. Specifically, the self-healing emulsion gels were fabricated by crosslinking carboxymethyl chitosan (CMC) stabilized emulsion with dialdehyde cellulose nanocrystal (DACNC). The reversible imine bonds between primary amino groups from CMC and aldehyde groups from DACNC endow the emulsion gel with self-healing properties. The compressive strength of the emulsion gels was greatly increased from 37.43 kPa 83.7 kPa by encapsulating emulsion droplets (φ = 0 %-40 %.) in the gel matrix. Moreover, the emulsion gels exhibited much better self-healing and injectability ability compared to hydrogel because the emulsion droplets interacted with the 3D gel matrix, which were observed by cryo-SEM and CLSM. The emulsion droplets distributed in the gel matrix improved the mobility and interfacial contact area of CMC and DACNC. Water contact measurement confirmed that the CMC/DACNC self-healing emulsion gels showed a hydrophilic surface. The CMC/DACNC emulsion gels could maintain a good structural stability as the oil loss was <1 % after centrifugation. This research provides a method to keep the structural stability of emulsion gels by inducing self-healing ability and modified cellulose nanocrystals, which could extend the shelf life and application area of emulsion gels.

Phytic Acid-Functional Cellulose Nanocrystals and Their Application in Self-Healing Nanocomposite Hydrogels

Cellulose nanocrystals (CNCs) have garnered significant attention as a modifiable substrate because of their exceptional performances, including remarkable degradability, high tensile strength, high elastic modulus, and biocompatibility. In this article, the successful adsorption of phytic acid (PA) onto the surface of cellulose nanocrystals @polydopamine (CNC@PDA) was achieved. Taking inspiration from mussels, a dopamine self-polymerization reaction was employed to coat the surface of CNCs with PDA. Utilizing Pickering emulsion, the CNC@PDA-PA nanomaterial was obtained by grafting PA onto CNC@PDA. An environmentally friendly hydrogel was prepared through various reversible interactions using poly(acrylic acid) (PAA) and Fe3+ as raw materials with the assistance of CNC@PDA-PA. By multiple hydrogen bonding and metal-ligand coordination, nanocomposite hydrogels exhibit remarkable mechanical properties (the tensile strength and strain were 1.82 MPa and 442.1%, respectively) in addition to spectacular healing abilities (96.6% after 5 h). The study aimed to develop an innovative approach for fabricating nanocomposite hydrogels with exceptional self-healing capabilities.

Pea protein/carboxymethyl cellulose complexes prepared using a pH cycle strategy as stabilizers of high internal phase emulsions for 3D printing

The development of food-grade high internal phase emulsions (HIPEs) for 3D printing and the replacement of animal fats have attracted considerable attention. In this study, in order to improve the rheological properties and stability of pea protein to prepare HIPE, pea protein/carboxymethyl cellulose (pH-PP/CMC) was prepared and subjected to pH cycle treatment to produce HIPEs. The results showed that pH cycle treatment and CMC significantly reduced the droplet size of HIPEs (from 143.33 to 12.10 μm). At higher CMC concentrations, the interfacial tension of the PP solution decreased from 12.84 to 11.71 mN/m without pH cycle treatment and to 10.79 mN/m with pH cycle treatment. The HIPEs with higher CMC concentrations subjected to pH cycle treatment showed shear thinning behavior and higher viscoelasticity and recovered their solid-like properties after being subjected to 50 % strain, indicating that they could be used for 3D printing. The 3D printing results showed that the pH-PP/CMC HIPE with 0.3 % CMC had the finest structure. Our work provides new insights into developing food-grade HIPEs and facilitating their use in 3D printing inks as nutrient delivery systems and animal fat substitutes.

Advancements in enzyme immobilization on magnetic nanomaterials: toward sustainable industrial applications

Enzymes are widely used in biofuels, food, and pharmaceuticals. The immobilization of enzymes on solid supports, particularly magnetic nanomaterials, enhances their stability and catalytic activity. Magnetic nanomaterials are chosen for their versatility, large surface area, and superparamagnetic properties, which allow for easy separation and reuse in industrial processes. Researchers focus on the synthesis of appropriate nanomaterials tailored for specific purposes. Immobilization protocols are predefined and adapted to both enzymes and support requirements for optimal efficiency. This review provides a detailed exploration of the application of magnetic nanomaterials in enzyme immobilization protocols. It covers methods, challenges, advantages, and future perspectives, starting with general aspects of magnetic nanomaterials, their synthesis, and applications as matrices for solid enzyme stabilization. The discussion then delves into existing enzymatic immobilization methods on magnetic nanomaterials, highlighting advantages, challenges, and potential applications. Further sections explore the industrial use of various enzymes immobilized on these materials, the development of enzyme-based bioreactors, and prospects for these biocatalysts. In summary, this review provides a concise comparison of the use of magnetic nanomaterials for enzyme stabilization, highlighting potential industrial applications and contributing to manufacturing optimization.

Periodate oxidation of nanofibrillated cellulose films for active packaging applications

An alternative packaging material based on cellulose that possesses excellent barrier properties and is potentially useful for active packaging has been developed. Cellulose nanofibril was efficiently and selectively oxidized with sodium periodate generating reactive aldehyde groups. These groups formed hemiacetal and hemialdal bonds during film formation and, consequently, highly transparent, elastic and strong films were created even under moisture saturation conditions. The periodate oxidation treatment additionally decreased the polarity of the films and considerably enhanced their water barrier properties. Thus, the water contact angle of films treated for 3 and 6 h was 97° and 102°, their water drop test value was higher than in untreated film (viz., 138 and 141 min with 3 and 6 h of treatment) and their water vapour transmission rate was substantially better (3.31 and 0.78 g m-2 day-1 with 3 and 6 h, respectively). The presence of aldehyde groups facilitated immobilization of the enzyme laccase, which efficiently captures oxygen and prevents food decay as a result. Laccase-containing films oxidized 80 % of Methylene Blue colorant and retained their enzymatic activity after storage for 1 month and 12 reuse cycles, opening the door to the possible creation of a reusable packaging to replace the single-use packaging.

Investigation of Cellulose-Based Materials Applied in Life Sciences Using Laser Light Scattering Methods

This review emphasizes the practical importance of laser light scattering methods for characterizing cellulose and its derivatives. The physicochemical parameters like molecular weights, the radius of gyration, hydrodynamic radius, and conformation will be considered when the reproducibility of polymer behavior in solution is necessary for the subsequent optimization of the property profile of a designed product. Since there are various sources of cellulose, and the methods of cellulose extraction and chemical modification have variable yields, materials with variable molecular weights, and size polydispersity will often result. Later, the molecular masses will influence other physicochemical properties of cellulosic materials, both in solution and solid state. Consequently, the most rigorous determination of these quantities is imperative. In this regard, the following are presented and discussed in this review: the theoretical foundations of the light scattering phenomenon, the evolution of the specific instrumentation and detectors, the development of the detector-coupling techniques which include a light scattering detector, and finally, the importance of the specific parameters of polymers in solution, resulting from the data analysis of light scattering signals. All these aspects are summarized according to the chemical classification of the materials: celluloses, esters of cellulose, co-esters of cellulose, alkyl esters of cellulose, ethers of cellulose, and other heterogeneous cellulose derivatives with applications in life sciences.

Polyrhodanine-based nanomaterials for biomedical applications: A review

Rhodanine is a heterocyclic organic compound that has been investigated for its potential biomedical applications, particularly in drug discovery. Rhodanine derivatives have been examined as the medication options for numerous illnesses, including cancer, inflammation, and infectious diseases. Some rhodanine derivatives have also shown promising activity against drug-resistant strains of bacteria and viruses. One of these derivatives is polyrhodanine (PR), a conducting polymer that has gained attention for its biomedical properties. This review article summarises the latest advancements in creating biomaterials based on PR for biosensing, antimicrobial treatments, and anticancer therapies. The distinctive characteristics of PR, such as biocompatibility, biodegradability, and good conductivity, render it an attractive candidate for these applications. The article also explores obstacles and potential future paths for advancing biomaterials made with PR, including synthesis modifications, characterisation techniques, and in vivo evaluation of biocompatibility and efficacy. Overall, as an emerging research topic, this review emphasises the potential of PR as a promising biomaterial for various biomedical applications and provides insights into the contemporary state of research and prospective directions for investigation.

Physical properties of cellulose nanocrystal/magnesium oxide/chitosan transparent composite films for packaging applications

Hitherto unreported hybrid nanofillers (CNC:MgO) reinforced chitosan (CTS) based composite (CNC:MgO)/CTS films were synthesized using a solution-casting blend technique and synergistic effect of hybrid nanofiller in terms of properties enhancement were investigated. Optical microscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD) technique, fourier-transform infrared spectroscopy (FTIR), and field emission scanning electron microscopy (FESEM) were used to characterize the films. The hybrid nanofiller considerably changed the transparency and color of the CTS films. The tensile strengths of (3 wt%) CNC/CTS, (3 wt%) MgO/CTS, (1:1)(CNC:MgO)/CTS, (1:2)(CNC:MgO)/CTS and (2:1)(CNC:MgO)/CTS films were 27.49 %, 35.60 %, 91.62 %, 38.22 %, and 29.32 % higher than pristine CTS films respectively, while the water vapor permeation were 28.21 %, 30.77 %, 34.62 %, 38.46 %, and 37.44 % lower than pristine CTS film, respectively. Moreover, the CTS composite films exhibited an improvement in overall water barrier properties after incorporating hybrid nanofillers. Our observations suggest that chitosan-based hybrid nanofiller composite films are a good replacement for plastic-based packaging materials within the food industry.

Carboxyl-modified nanocellulose (cNC) enhances the stability of cNC/pullulan bio-nanocomposite hard capsule against moisture variation

The quality of polysaccharide-based films and hard capsules is often affected by changes in relative humidity, manifesting as unstable water content, and changes in mechanical strength that make them brittle or soft. Herein, carboxyl-modified nanocellulose (cNC) was prepared and used as a new component to successfully improve the moisture resistance of cNC/pullulan/high-acyl gellan bio-nanocomposite hard capsules (NCPGs). Homogenously dispersed cNC in the pullulan/high-acyl gellan matrix could render the formation of more hydrogen bonds that provided additional water-binding sites and limited the free movement of pullulan and high-acyl gellan molecular chains within NCPGs. This contributed to a decreased amount of pooling adsorption water and an increased amount of Langmuir adsorption water in NCPGs, as compared to pullulan/high-acyl gellan hard capsules (PGs) without cNC. Therefore, the equilibrium moisture content (EMC) values of NCPGs decreased at 83 % relative humidity and increased at 23 % relative humidity compared to those of PGs. Together with enhanced mechanical and barrier properties, NCPGs effectively protected encapsulated amoxicillin and probiotic powder from changes in the outside humidity. Additionally, NCPGs exhibited faster drug release. This study presents a new mechanism and strategy for fabricating films and hard capsules with enhanced stability against moisture variation.

Oil palm frond-derived cellulose nanocrystals: Effect of pretreatment and elucidating its reinforcing potential in hydrogel beads

Herein, cellulose nanocrystals were synthesized from oil palm fronds (CNC-OPF) involving two pretreatment approaches, viz. autohydrolysis and soda pulping. The pretreatments were applied individually to OPF fibers to assess their influence on CNCs' physicochemical and thermal properties. CNC-OPF samples were assessed using complementary characterization techniques, which confirmed their purity and characteristics. CP/MAS 13C NMR and TEM studies revealed that autohydrolysis pretreatment yielded CNCs with effective hemicellulose and extractives removal compared to that of soda pulping. XRD analysis demonstrated that autohydrolysis-treated CNC-OPF contained a much higher crystallinity index compared to soda pulping treatment. BET measurement disclosed a relatively higher surface area and wider pore diameter of autohydrolysis-treated CNC-OPF. Autohydrolysis-treated CNCs were applied as a reinforcement filler in alginate-based hydrogel beads for the removal of 4-chlorophenol from water, which attained a qmax of 19.168 mg g-1. BET analysis revealed the less porous nature of CNC-ALG hydrogel beads which could have contributed to hydrogel beads' relatively lower adsorption capacity. The point of zero charge of CNC-ALG hydrogel beads was 4.82, suggesting their applicability only within a short solution pH range. This study directs future studies to unveil the possibilities of functionalizing CNCs in order to enhance the adsorption performance of CNC-immobilized hydrogel beads towards 4-chlorophenol and other organic contaminants.

Cellulose nanocrystals in the development of biodegradable materials: A review on CNC resources, modification, and their hybridization

The escalating demand for sustainable materials has propelled cellulose into the spotlight as a promising alternative to petroleum-based products. As the most abundant organic polymer on Earth, cellulose is ubiquitous, found in plants, bacteria, and even a unique marine animal-the tunicate. Cellulose polymers naturally give rise to microscale semi-crystalline fibers and nanoscale crystalline regions known as cellulose nanocrystals (CNCs). Exhibiting rod-like structures with widths spanning 3 to 50 nm and lengths ranging from 50 nm to several microns, CNC characteristics vary based on the cellulose source. The degree of crystallinity, crucial for CNC properties, fluctuates between 49 and 95 % depending on the source and synthesis method. CNCs, with their exceptional properties such as high aspect ratio, relatively low density (≈1.6 g cm-3), high axial elastic modulus (≈150 GPa), significant tensile strength, and birefringence, emerge as ideal candidates for biodegradable fillers in nanocomposites and functional materials. The percolation threshold, a mathematical concept defining long-range connectivity between filler and polymer, governs the effectiveness of reinforcement in nanocomposites. This threshold is intricately influenced by the aspect ratio and molecular interaction strength, impacting CNC performance in polymeric and pure nanocomposite materials. This comprehensive review explores diverse aspects of CNCs, encompassing their derivation from various sources, methods of modification (both physical and chemical), and hybridization with heterogeneous fillers. Special attention is devoted to the hybridization of CNCs derived from tunicates (TCNC) with those from wood (WCNC), leveraging the distinct advantages of each. The overarching objective is to demonstrate how this hybridization strategy mitigates the limitations of WCNC in composite materials, offering improved interaction and enhanced percolation. This, in turn, is anticipated to elevate the reinforcing effects and pave the way for the development of nanocomposites with tunable viscoelastic, physicochemical, and mechanical properties.

Biotechnological innovations in nanocellulose production from waste biomass with a focus on pineapple waste

New materials' synthesis and utilization have shown many critical challenges in healthcare and other industrial sectors as most of these materials are directly or indirectly developed from fossil fuel resources. Environmental regulations and sustainability concepts have promoted the use of natural compounds with unique structures and properties that can be biodegradable, biocompatible, and eco-friendly. In this context, nanocellulose (NC) utility in different sectors and industries is reported due to their unique properties including biocompatibility and antimicrobial characteristics. The bacterial nanocellulose (BNC)-based materials have been synthesized by bacterial cells and extracted from plant waste materials including pineapple plant waste biomass. These materials have been utilized in the form of nanofibers and nanocrystals. These materials are found to have excellent surface properties, low density, and good transparency, and are rich in hydroxyl groups for their modifications to other useful products. These materials are well utilized in different sectors including biomedical or health care centres, nanocomposite materials, supercapacitors, and polymer matrix production. This review explores different approaches for NC production from pineapple waste residues using biotechnological interventions, approaches for their modification, and wider applications in different sectors. Recent technological developments in NC production by enzymatic treatment are critically discussed. The utilization of pineapple waste-derived NC from a bioeconomic perspective is summarized in the paper. The chemical composition and properties of nanocellulose extracted from pineapple waste may have unique characteristics compared to other sources. Pineapple waste for nanocellulose production aligns with the principles of sustainability, waste reduction, and innovation, making it a promising and novel approach in the field of nanocellulose materials.

Preparation and characterization of cellulose nanocrystals with high stability from okara by green solvent pretreatment assisted TEMPO oxidation

Because the traditional preparation methods of cellulose nanocrystals (CNCs) involve chemical pollution issues, in this study, two typical green solvents, alkali/urea solvent (AUS) and deep-eutectic solvent (DES), were used to dissolve insoluble soybean fibers (ISF) extracted from okara and prepare regenerated CNCs (AUS/CNC and DES/CNC), which were further modified by TEMPO oxidation (AUS/T-CNC and DES/T-CNC). The recoveries of AUS and DES were 82.58 % and 84.00 %, respectively. Chemical composition analysis showed high cellulose purity (>95 %) of the regenerated CNCs. FTIR, XRD and 13C NMR analysis indicated the cellulose structure and polymorph of CNCs. Thermal analysis revealed that the maximum degradation peak of regenerated CNC shifted to a lower temperature. AFM revealed that CNCs exhibited rod-like fiber structures, while AUS-pretreated CNCs exhibited some special spherical fibers. TEMPO oxidation showed an enhancement effect on the characteristics of AUS/T-CNC and DES/T-CNC; DES/T-CNC exhibited higher stability and apparent viscosity than AUS/T-CNC. The DES/T-CNC-based cryogel displayed a higher adsorption capacity for anthocyanin (0.40 g/g) and curcumin (1.09 g/g) with good controlled release capacity. These results indicated that green solvent pretreatment-assisted TEMPO oxidation is a new environmentally friendly and low-cost method for the preparation of CNCs and shows excellent potential in the field of drug loading and controlled release.

Photocrosslinkable and hydroplasicable UV-shielding nanocellulose films facilitated by hydroxyl-yne click reaction

Sustainably-sourced functional nanocellulose materials are vitally important for the green and sustainable development. Herein, we reported photocrosslinkable and hydroplasticable TEMPO-oxidized cellulose nanofiber phenyl propylene ketone ethers (TOCNPPK) films with excellent ultraviolet (UV) shielding, highly reversible processability, and extended mechanical properties, which were facilitated by green hydroxyl-yne click reaction. The introduction of conjugated aromatic ring and vinyl bonds (-C=C-) had been demonstrated the key for the improved overall performance of resultant TOCNPPK, which not only endowed the TOCNPPK with nearly 100 % UV shielding, but also enabled it to be formed into diverse 3D shapes (helix, ring and letters "N, F, U") via the facile hydrosetting method. The photocrosslinkable-enhanced mechanical performance of TOCNPPK films was also attributed to -C=C- which could crosslink via [2π + 2π] cycloaddition reactions under UV-irradiation. The ultimate stress of TOCNPPK films was as high as 210.0 ± 22.8 MPa and the Young's modulus was 11.5 ± 0.7 GPa, much superior to those of 128.6 ± 8.5 MPa and 9.2 ± 0.6 GPa for pristine TOCN films. Furthermore, the TOCNPPK had been demonstrated as efficient nanofillers for both hydrophilic polyvinyl alcohol and lipophilic polycaprolactone to develop advanced biodegradable composite films with the integration of good water-wetting resistance, excellent UV blocking, and photo-enhanced mechanical performance.

Polysaccharide nanocomposites in wastewater treatment: A review

In modern times, wastewater treatment is vital due to increased water contamination arising from pollutants such as nutrients, pathogens, heavy metals, and pharmaceutical residues. Polysaccharides (PSAs) are natural, renewable, and non-toxic biopolymers used in wastewater treatment in the field of gas separation, liquid filtration, adsorption processes, pervaporation, and proton exchange membranes. Since addition of nanoparticles to PSAs improves their sustainability and strength, nanocomposite PSAs has gained significant attention for wastewater treatment in the past decade. This review presents a comprehensive analysis of PSA-based nanocomposites used for efficient wastewater treatment, focusing on adsorption, photocatalysis, and membrane-based methods. It also discusses potential future applications, challenges, and opportunities in adsorption, filtration, and photocatalysis. Recently, PSAs have shown promise as adsorbents in biological-based systems, effectively removing heavy metals that could hinder microbial activity. Cellulose-mediated adsorbents have successfully removed various pollutants from wastewater, including heavy metals, dyes, oil, organic solvents, pesticides, and pharmaceutical residues. Thus, PSA nanocomposites would support biological processes in wastewater treatment plants. A major concern is the discharge of antibiotic wastes from pharmaceutical industries, posing significant environmental and health risks. PSA-mediated bio-adsorbents, like clay polymeric nanocomposite hydrogel beads, efficiently remove antibiotics from wastewater, ensuring water quality and ecosystem balance. The successful use of PSA-mediated bio-adsorbents in wastewater treatment depends on ongoing research to optimize their application and evaluate their potential environmental impacts. Implementing these eco-friendly adsorbents on a large scale holds great promise in significantly reducing water pollution, safeguarding ecosystems, and protecting human health.

Enhanced safety and strength of cotton fabrics through a novel 'H-shaped' multiple flame retardant elements agent

In response to the new concept of green sustainability, it is necessary to expand the functionality of bio-based natural fibers (such as cotton fabrics) to replace fabrics made from fossil fuels. One potential way of achieving this is through the use of phosphorus, boron and nitrogen based organic flame retardants. This article designs a special flame retardant system with high efficiency, high durability, and enhanced fabric strength. An "H" shaped flame retardant (TBSA) is synthesized using hydroxyethyl methylene phosphate, pentaerythritol diborate, and cyanuric chloride. After simple treatment, flame retardant fabric (TBSA/Cotton) is obtained, with a LOI value of 48.8 %. Self extinguishing is completing in the vertical flame test. The high FR efficiency reflects the progressiveness of multi flame retardant elements. It is worth noting that TBSA/Cotton exhibits excellent durability and improves the strength of the fabric. This is attributed to the covalent bonding between the "H" type flame retardant and multiple cellulose molecules, which compensates for the cracks and holes at the submicroscopic scale of natural cellulose and weakens the molecular slip effect. The research results of this article provide a good opportunity for the development of biomass cellulose flame retardant materials.

The Effect of Cellulose Nanocrystal-Based Nanofluid on Milling Performance: An Investigation of Dillimax 690T

Machining high-strength structural steels often requires challenging processes. It is essential to improve the machinability of such materials, which are frequently needed in industrial manufacturing areas. Recently, it has become necessary to enhance the machinability of such materials using different nanopowders. In this study, different cooling/lubricating (C/L) liquids were prepared with cellulose nanocrystal (CNC) nanopowder. The aim was to improve the machinability properties of Dillimax 690T material with the prepared CNC-based cutting fluids. CNC nanopowders were added to 0.5% distilled water by volume, and a new nanofluid was produced. Unlike previous studies, base synthetic oil and CNC-based cutting fluid were sprayed on the cutting area with a double minimum quantity lubrication (MQL) system. Machinability tests were carried out by milling. Two different cutting speeds (Vc = 120-150 m/min), two different feed rates (f = 0.05-0.075 mm/tooth), and four different C/L environments (dry, MQL oil, CNC nanofluid, MQL oil + CNC nanofluid) were used in the experiments. In the study, where a total of 16 experiments were performed, cutting temperature (Tc), surface roughness (Ra), tool wear (Vb), and energy consumption results were analyzed in detail. According to the test results, significant improvements were achieved in the machinability properties of the material in the experiments carried out using CNC nanofluid. In particular, the hybrid C/L environment using MQL oil + CNC nanofluid improved all machinability metrics by over 15% compared to dry machining. In short, using CNC nanopowders offers a good milling process of Dillimax 690T material with effective lubrication and cooling ability.

Low-Frequency Ultrasound Effects on Cellulose Nanocrystals for Potential Application in Stabilizing Pickering Emulsions

Cellulose, in the form of cellulose nanocrystals (CNCs), is a promising biomaterial for stabilizing Pickering emulsions (PEs). PEs are commonly formed using low-frequency ultrasound (LFU) treatment and impact CNC properties. The present study investigated the specific effects of LFU treatment on CNCs' chemical and physical properties. CNCs were characterized using dynamic light scattering, ζ;-potential determination, Fourier transform infrared spectroscopy, X-ray diffraction, and contact angle measurement. CNC suspensions were studied using rheological analysis and static multiple light scattering. LFU treatment broke CNC aggregates and modified the rheological behavior of CNC suspensions but did not affect the CNCs' chemical or crystallographic structures, surface charge, or hydrophilic properties. During the storage of CNC suspensions and PEs, liquid crystal formation was observed with cross-polarized light. Hypotheses related to the impact of liquid crystal CNCs on PE stability were proposed.

Synthesis and properties of thiol-modified CNC via surface tosylation

SH-containing polymers and nanoparticles are a significant direction in the creation of novel materials. The aim of this work is the synthesis of cellulose nanocrystals (CNC) with a surface modified by tosyl functions (CNC-Ts) and their further modification into SH-containing nanocrystals (CNC-SH). CNC-Ts were synthesized in an aqueous-organic emulsion from never-dried particles, while maintaining the size and supramolecular structure of CNC; the content of Ts-functions is up to 2.5 mmol·g-1. Structure of the derivatives was analyzed by TEM, XRD, CP/MAS 13C NMR and FTIR spectroscopies. Nucleophilic substitution and hydrolysis of the obtained thioisouronium salts leads to the production of CNC-SH. To quantify SH-groups we used elemental analysis, potentiometric titration and Folin-Ciocalteu and Ellman's reagents. It is shown that SH-groups on the surface are partially oxidized and are involved in a dense network of hydrogen bonds. Rheological properties of CNC-SH hydrosols are close to those of CNC, addition of H2O2 at acidic pH leads to an increase in viscosity of the system; H2O2 added at neutral pH causes opposite effect - viscosity decreases. CNC-SH have a high capacity for sorption of Cr(VI) in acidic environments and exhibit photoreductive properties under UV irradiation.

Obtaining Cellulose Nanocrystals from Olive Tree Pruning Waste and Evaluation of Their Influence as a Reinforcement on Biocomposites

The objective of this work is to improve the mechanical properties of polylactic acid (PLA) by incorporating cellulose nanocrystals (CNC) previously obtained from a cellulose pulp extracted from olive tree pruning (OTP) waste. Composites were manufactured by melt processing and injection moulding to evaluate the effect of the introduction of CNC with conventional manufacturing methods. This OTP-cellulose pulp was subjected to a further purification process by bleaching, thus bringing the cellulose content up to 86.1%wt. This highly purified cellulose was hydrolysed with sulfuric acid to obtain CNCs with an average length of 267 nm and a degradation temperature of 300 °C. The CNCs obtained were used in different percentages (1, 3, and 5%wt.) as reinforcement in the manufacture of PLA-based composites. The effect of incorporating CNC into PLA matrix on the mechanical, water absorption, thermal, structural, and morphological properties was studied. Maximum tensile stress and Young's modulus improved by 87 and 58%, respectively, by incorporating 3 and 5%wt. CNC. Charpy impact strength increased by 21% with 3%wt. These results were attributed to the good dispersion of CNCs in the matrix, which was corroborated by SEM images. Crystallinity index, glass transition, and melting temperatures were maintained.

Cellulose-based adsorbents for solid phase extraction and recovery of pharmaceutical residues from water

Cellulose has attracted interest from researchers both in academic and industrial sectors due to its unique structural and physicochemical properties. The ease of surface modification of cellulose by the integration of nanomaterials, magnetic components, metal organic frameworks and polymers has made them a promising adsorbent for solid phase extraction of emerging contaminants, including pharmaceutical residues. This review summarizes, compares, and contrasts different types of cellulose-based adsorbents along with their applications in adsorption, extraction and pre-concentration of pharmaceutical residues in water for subsequent analysis. In addition, a comparison in efficiency of cellulose-based adsorbents and other types of adsorbents that have been used for the extraction of pharmaceuticals in water is presented. From our observation, cellulose-based materials have principally been investigated for the adsorption of pharmaceuticals in water. However, this review aims to shift the focus of researchers to the application of these adsorbents in the effective pre-concentration of pharmaceutical pollutants from water at trace concentrations, for quantification. At the end of the review, the challenges and future perspectives regarding cellulose-based adsorbents are discussed, thus providing an in-depth overview of the current state of the art in cellulose hybrid adsorbents for extraction of pharmaceuticals from water. This is expected to inspire the development of solid phase exraction materials that are efficient, relatively cheap, and prepared in a sustainable way.

Fabrication of Superhydrophobic Water-Pinning Surfaces through Integration of Silica Colloids into Cellulose Nanocrystals

The water-pinning effect is a phenomenon in which water droplets adhere to a surface and do not roll off, even when the surface is tilted or turned upside down. This effect holds great potential for applications in various areas, such as dew collection in arid regions, anti-drip function for a greenhouse, and liquid transport and control. However, creating surfaces that exhibit this effect poses challenges, necessitating materials with both hydrophobicity and high adhesive force along with a scalable, cost-effective method to produce the essential geometries that have not yet been established. To address these challenges, we propose a straightforward coating approach involving silica nanoparticles (SiO2) and cellulose nanocrystals (CNCs) to fabricate artificial water-pinning surfaces. We assessed the water-pinning ability of the coated surface through measurements of the contact angle, contact radius, and hysteresis. Remarkably, the coated surface exhibited a contact angle of approximately 153.87° and a contact radius of around 0.89 mm when a 10 μL water droplet was applied, demonstrating its resistance to rolling off, even at a tilting angle of 90°. The droplet only began to fall when its volume reached approximately 33 μL, requiring a substantial water pinning force of 323.4 μN. We also investigated the physicochemical characteristics of the SiO2@CNC coating surface, including morphology, chemical composition, and chemical structure, to unravel the underlying mechanism behind its water-pinning ability. Our proposed fabrication method offers a promising avenue for the development of functional biopolymer-based surfaces capable of precisely manipulating water droplets.

Thermoplastic Starch Biocomposite Films Reinforced with Nanocellulose from Agave tequilana Weber var. Azul Bagasse

In this work, cellulose nanocrystals (CNCs), bleached cellulose nanofibers (bCNFs), and unbleached cellulose nanofibers (ubCNFs) isolated by acid hydrolysis from Agave tequilana Weber var. Azul bagasse, an agro-waste from the tequila industry, were used as reinforcements in a thermoplastic starch matrix to obtain environmentally friendly materials that can substitute contaminant polymers. A robust characterization of starting materials and biocomposites was carried out. Biocomposite mechanical, thermal, and antibacterial properties were evaluated, as well as color, crystallinity, morphology, rugosity, lateral texture, electrical conductivity, chemical identity, solubility, and water vapor permeability. Pulp fibers and nanocelluloses were analyzed via SEM, TEM, and AFM. The water vapor permeability (WVP) decreased by up to 20.69% with the presence of CNCs. The solubility decreases with the presence of CNFs and CNCs. The addition of CNCs and CNFs increased the tensile strength and Young's modulus and decreased the elongation at break. Biocomposites prepared with ubCNF showed the best tensile mechanical properties due to a better adhesion with the matrix. Images of bCNF-based biocomposites demonstrated that bCNFs are good reinforcing agents as the fibers were dispersed within the starch film and embedded within the matrix. Roughness increased with CNF content and decreased with CNC content. Films with CNCs did not show bacterial growth for Staphylococcus aureus and Escherichia coli. This study offers a new theoretical basis since it demonstrates that different proportions of bleached or unbleached nanofibers and nanocrystals can improve the properties of starch films.

Ni(II) and Pb(II) Removal Using Bacterial Cellulose Membranes

Bacterial cellulose (BC) is a highly crystalline nanosized material with a high number of active groups. This study focuses on the synthesis of BC membranes through fermentation, their characterization and application to remove Ni(II) and Pb(II) from wastewater by adsorption under different conditions. Four-day-grown BC membranes form three-dimensional nanofibril networks with a pH of 6.3 and a high cationic demand (52.5 μeq·g-1). The pseudo-second-order kinetic model and the Sips isotherm model best describe the adsorption of both metals. The intraparticle diffusion model of Ni(II) revealed a three-step mechanism of adsorption-plateau-adsorption, while Pb(II) adsorption followed a typical reducing-slope trend up to saturation. The highest removal of Ni(II) and Pb(II) was obtained at pH 4 with a BC dosage of 400 mg·L-1. The maximum adsorption capacities were 28.18 mg·g-1 and 8.49 mg·g-1 for Ni(II) and Pb(II), respectively, involving the total coverage of the material active sites. Thermodynamically, Ni(II) adsorption was exothermic, and Pb(II) was endothermic. The obtained values of sorption heat, activation and Gibbs' energy depicted a physisorption process. Ni(II) removal mechanism was ruled by crystallization on the metals adsorbed on the BC active groups, while Pb(II) was driven by the adsorption process, as shown by TEM images of the spent material.

Coping with the cold: unveiling cryoprotectants, molecular signaling pathways, and strategies for cold stress resilience

Low temperature stress significantly threatens crop productivity and economic sustainability. Plants counter this by deploying advanced molecular mechanisms to perceive and respond to cold stress. Transmembrane proteins initiate these responses, triggering a series of events involving secondary messengers such as calcium ions (Ca2+), reactive oxygen species (ROS), and inositol phosphates. Of these, calcium signaling is paramount, activating downstream phosphorylation cascades and the transcription of cold-responsive genes, including cold-regulated (COR) genes. This review focuses on how plants manage freeze-induced damage through dual strategies: cold tolerance and cold avoidance. Tolerance mechanisms involve acclimatization to decreasing temperatures, fostering gradual accumulation of cold resistance. In contrast, avoidance mechanisms rely on cryoprotectant molecules like potassium ions (K+), proline, glycerol, and antifreeze proteins (AFPs). Cryoprotectants modulate intracellular solute concentration, lower the freezing point, inhibit ice formation, and preserve plasma membrane fluidity. Additionally, these molecules demonstrate antioxidant activity, scavenging ROS, preventing protein denaturation, and subsequently mitigating cellular damage. By forming extensive hydrogen bonds with water molecules, cryoprotectants also limit intercellular water movement, minimizing extracellular ice crystal formation, and cell dehydration. The deployment of cryoprotectants is a key adaptive strategy that bolsters plant resilience to cold stress and promotes survival in freezing environments. However, the specific physiological and molecular mechanisms underlying these protective effects remain insufficiently understood. Therefore, this review underscores the need for further research to elucidate these mechanisms and assess their potential impact on crop productivity and sustainability, contributing to the progressive discourse in plant biology and environmental science.

Wound Dressing Double-Crosslinked Quick Self-Healing Hydrogel Based on Carboxymethyl Chitosan and Modified Nanocellulose

The use of hydrogels in wound dressings, which is pivotal for effective wound treatment, has been widely applied to diverse medical wound conditions. However, formulating natural hydrogels that combine robust strength and self-healing capabilities is a significant challenge. To overcome this, we successfully designed a natural nanocellulose self-healing hydrogel that can quickly self-heal and restore the complete hydrogel structure after injury to fill the injured area and protect the wound from external damage. Our study utilized modified natural polymer carboxymethyl chitosan (CMC), hydrazide-modified carboxymethyl cellulose nanofibers (HCNF), and cellulose nanocrystals modified by dialdehyde (DACNC) to fabricate the hydrogel. The amides containing more amino groups and HCNF in CMC can be used as cross-linking nodes, and the high aspect ratio and specific surface area of DACNC are favorable for the connection of many active hydrogels. The hydrogel is crosslinked by the dynamic imide bond and hydrazone bond between the amino group of CMC, the amide of HCNF, and the aldehyde of DACNC and has a double network structure. These connections can be readily reassembled when disrupted, enabling fast self-healing of hydrogels within five minutes. Moreover, HCNF and DACNC were incorporated as nano-reinforced fillers to bolster the hydrogel's strength while preserving its high liquid absorption capacity (381% equilibrium swelling rate).

Polyelectrolyte membranes based on phosphorylated-PVA/cellulose acetate for direct methanol fuel cell applications: synthesis, instrumental characterization, and performance testing

Designing and synthesis of cost-effective and improved methanol permeable and proton conductive membranes are the main challenges for preparation of polymeric electrolyte membrane (PEM). Herein, a cost-effective PEM membrane based on phosphorylated polyvinyl alcohol (PVA)-grafted-cellulose acetate (CA) was prepared by a solution-casting technique. Water and methanol uptakes of phosphorylated PVA/CA membranes were characterized as function with the molar ratio of CA. Additionally, structure and morphology of phosphorylated PVA/CA (Ph-PVA/CA) membranes were verified by FT-IR analysis, SEM investigation. Furthermore, ion exchange capacity (IEC), proton conductivity and methanol permeation of Ph-PVA/CA membranes were examined based on the concentration of OPA basically. The results manifested a perceptible improvement in proton conductivity from 0.035 to 0.05 S/cm at 25 and 70 °C, respectively using 600 μL of OPA, and IEC of 2.1 meq/g using 400 μL of OPA at ambient temperature. On the other hand, methanol permeability (P = 1.08 × 10-10 cm2/s) was lower than Nafion 117 admirably. The optimum OPA concentration was 200 μL according to conductivity measurements (at 10% PVA, 150 μL GA, and CA 7%). Finally, prepared Ph-PVA/CA membranes exhibited enhancement in critical natures such as proton conductivity and IEC combined with its low-cost materials, which make them excellent candidate as PEM for DMFCs application.

Rosacea Topical Treatment and Care: From Traditional to New Drug Delivery Systems

Rosacea is a multifactorial chronic inflammatory dermatosis characterized by flushing, nontransient erythema, papules and pustules, telangiectasia, and phymatous alterations accompanied by itching, burning, or stinging, the pathophysiology of which is not yet fully understood. Conventional topical treatments usually show limited efficacy due to the physical barrier property of the skin that hinders skin penetration of the active ingredients, thereby hampering proper drug skin delivery and the respective therapeutic or cosmetic effects. New advances regarding the physiopathological understanding of the disease and the underlying mechanisms suggest the potential of new active ingredients as promising therapeutic and cosmetic approaches to this dermatosis. Additionally, the development of new drug delivery systems for skin delivery, particularly the potential of nanoparticles for the topical treatment and care of rosacea, has been described. Emphasis has been placed on their reduced nanometric size, which contributes to a significant improvement in the attainment of targeted skin drug delivery. In addition to the exposition of the known pathophysiology, epidemiology, diagnosis, and preventive measures, this Review covers the topical approaches used in the control of rosacea, including skin care, cosmetics, and topical therapies, as well as the future perspectives on these strategies.

Recent advances in qualitative and quantitative characterization of nanocellulose-reinforced nanocomposites: A review

Nanocellulose has received immense consideration owing to its valuable inherent traits and impressive physicochemical properties such as biocompatibility, thermal stability, non-toxicity, and tunable surface chemistry. These features have inspired researchers to deploy nanocellulose as nanoscale reinforcement materials for bio-based polymers. A simple yet efficient characterization method is often required to gain insights into the effectiveness of various types of nanocellulose. Despite a decade of continuous research and booming growth in scientific publications, nanocellulose research lacks a measuring tool that can characterize its features with acceptable speed and reliability. Implementing reliable characterization techniques is critical to monitor the specifications of nanocellulose alone or in the final product. Many techniques have been developed aiming to measure the nano-reinforcement mechanisms of nanocellulose in polymer composites. This review gives a full account of the scientific underpinnings of techniques that can characterize the shape and arrangement of nanocellulose. This review aims to deliver consolidated details on the properties and characteristics of nanocellulose in biopolymer composite materials to improve various structural, mechanical, barrier and thermal properties. We also present a comprehensive description of the safety features of nanocellulose before and after being loaded within biopolymeric matrices.

Tannic acid-coated cellulose nanocrystals with enhanced mucoadhesive properties for aquaculture

Mucoadhesion can be exploited as a strategy to target drug and nutrient delivery to the outer mucosal layers of fish in aquaculture farms. Cellulose nanocrystals (CNC) derived from cellulose pulp fibers can interact with the mucosal membranes via hydrogen bonding, however, their mucoadhesive properties are weak and should be enhanced. In this study, CNC were coated with tannic acid (TA), a plant polyphenol with excellent wet-resistant bioadhesive properties, to strengthen their mucoadhesive capability. The optimal CNC:TA mass ratio was determined to be 20:1. The modified CNCs were 190 ± 40 nm in length and 21 ± 4 nm wide and displayed excellent colloidal stability, with a zeta potential of -35 mV. Turbidity titrations and rheological measurements revealed that the modified CNC possessed superior mucoadhesive properties compared to pristine CNC. Modification with tannic acid introduced additional functional groups for stronger hydrogen bond formation and hydrophobic interactions with mucin, which was confirmed by a large reduction in viscosity enhancement values in the presence of chemical blockers (urea and Tween80). The enhanced mucoadhesion of the modified CNC could be utilized for the fabrication of a mucoadhesive drug delivery system to promote sustainable aquaculture practices.

An introductory review on advanced multifunctional materials

This review summarizes the applications of some of the advanced materials. It included the synthesis of several nanoparticles such as metal oxide nanoparticles (e.g., Fe₃O₄, ZnO, ZrOSO₄, MoO_3-x, CuO, AgFeO₂, Co₃O₄, CeO₂, SiO₂, and CuFeO₂); metal hydroxide nanosheets (e.g., Zn₅(OH)₈(NO₃)₂·2H₂O, Zn(OH)(NO₃)·H₂O, and Zn₅(OH)₈(NO₃)₂); metallic nanoparticles (Ag, Au, Pd, and Pt); carbon-based nanomaterials (graphene, graphene oxide (GO), graphitic carbon nitride (g-C₃N₄), and carbon dots (CDs)); biopolymers (cellulose, nanocellulose, TEMPO-oxidized cellulose nanofibers (TOCNFs), and chitosan); organic polymers (e.g. covalent-organic frameworks (COFs)); and hybrid materials (e.g. metal-organic frameworks (MOFs)). Most of these materials were applied in several fields such as environmental-based technologies (e.g., water remediation, air purification, gas storage), energy (production of hydrogen, dimethyl ether, solar cells, and supercapacitors), and biomedical sectors (sensing, biosensing, cancer therapy, and drug delivery). They can be used as efficient adsorbents and catalysts to remove emerging contaminants e.g., inorganic (i.e., heavy metals) and organic (e.g., dyes, antibiotics, pesticides, and oils in water via adsorption. They can be also used as catalysts for catalytic degradation reactions such as redox reactions of pollutants. They can be used as filters for air purification by capturing carbon dioxide (CO₂) and volatile organic compounds (VOCs). They can be used for hydrogen production via water splitting, alcohol oxidation, and hydrolysis of NaBH₄. Nanomedicine for some of these materials was also included being an effective agent as an antibacterial, nanocarrier for drug delivery, and probe for biosensing.

A Comparison of the Effect of Cellulose Nanocrystals (CNCs) and Polyethylene Glycol (PEG) as Additives in Ultrafiltration Membranes (PES-UF): Characterization and Performance

This work demonstrated the potential of CNC as a substitute for PEG as an additive in ultrafiltration membrane fabrication. Two sets of modified membranes were fabricated using the phase inversion technique, with polyethersulfone (PES) as the base polymer and 1-N-methyl-2 pyrrolidone (NMP) as the solvent. The first set was fabricated with 0.075 wt% CNC, while the second set was fabricated with 2 wt% PEG. All membranes were characterized using SEM, EDX, FTIR, and contact angle measurements. The SEM images were analyzed for surface characteristics using WSxM 5.0 Develop 9.1 software. The membranes were tested, characterized, and compared for their performance in treating both synthetic and real restaurant wastewater. Both membranes exhibited improved hydrophilicity, morphology, pore structure, and roughness. Both membranes also exhibited similar water flux for real and synthetic polluted water. However, the membrane prepared with CNC gave higher turbidity removal and COD removal when raw restaurant water was treated. The membrane compared well with the UF membrane containing 2 wt% PEG in terms of morphology and performance when synthetic turbid water and raw restaurant water were treated.

Simple engineering of hybrid cellulose nanocrystal-gold nanoparticles results in a functional glyconanomaterial with biomolecular recognition properties

Cellulose nanocrystal and gold nanoparticles are assembled, in a unique way, to yield a novel modular glyconanomaterial whose surface is then easily engineered with one or two different headgroups, by exploiting a robust click chemistry route. We demonstrate the potential of this approach by conjugating monosaccharide headgroups to the glyconanomaterial and show that the sugars retain their binding capability to C-type lectin receptors, as also directly visualized by cryo-TEM.

High-yield production of rod-like and spherical nanocellulose by controlled enzymatic hydrolysis of mechanically pretreated cellulose

In this study, a simple and scalable mechanical pretreatment was evaluated as means to increase the cellulose accessibility of cellulose fibers, with the aim of improving the efficiency of enzymatic reactions for the production of cellulose nanoparticles (CNs). In addition, the effects of enzyme type (endoglucanase - EG, endoxylanase - EX, and a cellulase preparation - CB), composition ratio (0-200UEG:0-200UEX or EG, EX, and CB alone), and loading (0 U-200 U) were investigated in relation to CN yield, morphology, and properties. The combination of mechanical pretreatment and specific conditions for enzymatic hydrolysis substantially improved CN production yield, reaching up to 83 %. The production of rod-like or spherical nanoparticles and their chemical composition were highly dependent on the type of enzyme, composition ratio, and loading. However, these enzymatic conditions minimally affected the crystallinity index (approximately 80 %) and thermal stability (T_max within 330-355 °C). Collectively, these results demonstrate that mechanical pretreatment followed by enzymatic hydrolysis under specific conditions is a suitable method to produce nanocellulose with a high yield and tunable properties such as purity, rod-like or spherical forms, high thermal stability, and high crystallinity. Therefore, this production route is a promising approach to produce tailored CNs with the potential to offer superior performance in a variety of sophisticated applications, including, but not limited to, wound dressings, drug delivery, thermoplastic composites, 3D (bio)printing, and smart packaging.

Date Palm Tree Leaf-Derived Cellulose Nanocrystal Incorporated Thin-Film Composite forward Osmosis Membranes for Produced Water Treatment

Worldwide water shortage and significant issues related to treatment of wastewater streams, mainly the water obtained during the recovery of oil and gas operations called produced water (PW), has enabled forward osmosis (FO) to progress and become advanced enough to effectively treat as well as retrieve water in order to be productively reused. Because of their exceptional permeability qualities, thin-film composite (TFC) membranes have gained increasing interest for use in FO separation processes. This research focused on developing a high water flux and less oil flux TFC membrane by incorporating sustainably developed cellulose nanocrystal (CNC) onto the polyamide (PA) layer of the TFC membrane. CNCs are prepared from date palm leaves and different characterization studies verified the definite formations of CNCs and the effective integration of CNCs in the PA layer. From the FO experiments, it was confirmed that that the membrane with 0.05 wt% of CNCs in the TFC membrane (TFN-5) showed better FO performance in PW treatment. Pristine TFC and TFN-5 membrane exhibited 96.2% and 99.0% of salt rejection and 90.5% and 97.45% of oil rejection. Further, TFC and TFN-5 demonstrated 0.46 and 1.61 LMHB pure water permeability and 0.41 and 1.42 LHM salt permeability, respectively. Thus, the developed membrane can help in overcoming the current challenges associated with TFC FO membranes for PW treatment processes.

Insights into thermal degradation kinetics and liquid crystalline behavior of cellulose nanocrystals from the waste of Cajanus cajan (pigeon pea)

Cellulose nanocrystals (CNCs) are essential for advancing nanotechnology and modern science. This work used the Cajanus cajan stem, an agricultural waste, as a lignocellulosic mass, which can serve as a supply of CNCs. After extraction from the Cajanus cajan stem, CNCs have been thoroughly characterized. FTIR (Infrared Spectroscopy) and ssNMR (solid-state Nuclear Magnetic Resonance) successfully validated eliminating additional components from the waste stem. The ssNMR and XRD (X-ray diffraction) were utilized to compare the crystallinity index. For structural analysis, the XRD of cellulose I_β was simulated to compare with the extracted CNCs. Various mathematical models inferred thermal stability and its degradation kinetics to ensure its high-end applications. Surface analysis established the rod-like shape of the CNCs. Rheological measurements were performed to gauge the liquid crystalline properties of CNC. The anisotropic liquid crystalline CNCs' birefringence proves that the Cajanus cajan stem is a promising resource for making CNCs for cutting-edge applications.

Recent advances in the hybridization of cellulose and semiconductors: Design, fabrication and emerging multidimensional applications: A review

Cellulose is a plentiful, biodegradable, renewable, and natural polymer in the world that can be widely utilized in the production of polymer nanocomposites. Cellulose is developed in nanomaterials owing to its remarkable inherent features of low density, non-toxicity, and affordability, as well as the amazing sample characteristics of strength and thermal stability. Recently, there has been a lot of interest in organic-inorganic composites because of their adaptable qualities. Cellulose and semiconductors have exciting properties, and new combinations of both materials may result in efficient functional hybrid composites with distinct properties. Lately, a huge study was reported on cellulose and semiconductor-based nanocomposites. In this review, we summarize the present research development in the preparation methods, structure, features, and possible applications of multifunctional cellulose and semiconductor-based nanocomposites. The cellulose/semiconductor based nanocomposites have massive potential applications in the areas of photodegradation of organic dyes, hydrogen production, metal removal, biomedical, and sensor applications. It is also assumed that this article will promote additional investigation and will establish innovative capabilities to enhance novel cellulose and semiconductor based nanocomposites with new and exciting applications.

Cellulose Nanocrystals (CNCs) and Cellulose Nanofibers (CNFs) as Adsorbents of Heavy Metal Ions

The isolation of nanocellulose has been extensively investigated due to the growing demand for sustainable green materials. Cellulose nanocrystals (CNCs) and cellulose nanofibers (CNFs), which have the same chemical composition but have different morphology, particle size, crystallinity, and other properties depending on the precursor and the synthesis method used. In comparison, CNC particles have a short rod-like shape and have smaller particle dimensions when compared to CNF particles in the form of fibers. CNC synthesis was carried out chemically (hydrolysis method), and CNF synthesis was carried out mechanically (homogenization, ball milling, and grinding), and both can be modified because they have a large surface area and are rich in hydroxyl groups. Modifications were made to increase the adsorption ability of heavy metal ions. The Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric (TG), and dynamic light scattering (DLS) can reveal the characteristics and morphology of CNCs and CNFs. The success and effectiveness of the heavy metal adsorption process are influenced by a few factors. These factors include adsorbent chemical structure changes, adsorbent surface area, the availability of active sites on the adsorbent’s surface, adsorption constants, heavy metal ionic size differences, pH, temperature, adsorbent dosage, and contact time during the adsorption process. In this review, we will discuss the characteristics of CNCs and CNFs synthesized from various precursors and methods, the modification methods, and the application of CNCs and CNFs as heavy metal ion adsorbents, which includes suitable isotherm and kinetics models and the effect of pH on the selectivity of various types of heavy metal ions.

Strong, flexible and UV-shielding composite polyvinyl alcohol films with wood cellulose skeleton and lignin nanoparticles

The development of high-performance composite films using biomass materials have become a sought-after direction. Herein, a green method to fabricate strong, flexible and UV-shielding biological composite film from wood cellulose skeleton (WCS), lignin nanoparticles (LNPs) and polyvinyl alcohol (PVA) was described. In the work, WCS and LNPs were prepared by chemical treatment of wood veneer and Enzymatic lignin, respectively. Then, WCS was infiltrated with the LNPs/PVA mixtures and dried to obtain composite films. WCS enhanced the mechanical properties of the composite films, the tensile stress reached to 85.8 MPa and the tensile strain reached to 6.39 %. The composite films with LNPs blocked over 98 % of UV-light, the water absorption decreased by 30 %, and the thermal stabilities were also improved. These findings would provide some references for exploring high quality biological composite films.

Integrated Biobased Processes for Nanocellulose Preparation from Rice Straw Cellulose

High-potential nanomaterials were derived from rice straw using the integrated biobased processes of enzymatic hydrolysis with green organic acid hydrolysis assisted with ultrasonication pretreatment. The optimization condition of nanocellulose preparation by enzymatic hydrolysis via central composite design (CCD) achieved a maximum nanocellulose content of 32.37 ± 0.47% using a cellulase concentration of 107.06 U/mL and 0.13% (w/w) of rice straw cellulose. The ultrasonication-assisted pretreatment prior to enzymatic hydrolysis improved nanocellulose preparation to 52.28 ± 1.55%. Integration with oxalic acid hydrolysis increased the nanocellulose content to 64.99 ± 0.16%. Granular nanocellulose was obtained and consisted of a 105–825 nm nanosize with a zeta potential value of −34.5 mV, and nanocellulose suspension showed high stability without aggregation. In addition, the remaining rice straw cellulose after oxalic acid was microcrystalline nanocellulose. All prepared nanocellulose represented a functional group as original cellulose but had a low crystallinity index (CrI) of 15.68% that could be classified as amorphous nanocellulose. Based on their characteristics, all nanocellose could be further applied in food, cosmetics, and pharmaceuticals. Moreover, the results indicated that the rice straw could be an alternative non-edible cellulose source for preparing potential nanocellulose via a controlled hydrolysis process.

Morphological, Spectroscopic and Thermal Analysis of Cellulose Nanocrystals Extracted from Waste Jute Fiber by Acid Hydrolysis

Natural cellulose, a sustainable bioresource, is highly abundant in nature. Cellulosic materials, particularly those that explore and employ such materials for industrial use, have recently attracted significant global attention in the field of material science because of the unique properties of cellulose. The hydroxyl groups enable the formation of intra- and inter-molecular hydrogen bonding and the arrangement of cellulose chains in a highly ordered crystalline zone, with the remaining disordered structure referred to as an amorphous region. The crystalline areas of cellulose are well-known as cellulose nanocrystals (CNCs). In the present study, we extracted CNCs from pure cellulose isolated from waste jute fibers by sulfuric acid hydrolysis, followed by characterization. Pure cellulose was isolated from jute fibers by treating with sodium hydroxide (20% w/w) and anthraquinone (0.5%) solution at 170 °C for 2 h, followed by bleaching with chlorine dioxide and hydrogen peroxide solution. CNCs were isolated from pure cellulose by treating with different concentrations (58% to 62%) of sulfuric acid at different time intervals (20 min to 45 min). The FTIR study of the CNCs reveals no peak at 1738 cm^-1, which confirms the absence of hemicellulose in the samples. The CNCs obtained after 45 min of acid hydrolysis are rod-shaped, having an average length of 800 ± 100 nm and width of 55 ± 10 nm, with a high crystallinity index (90%). Zeta potential significantly increased due to the attachment of SO₄^2- ions on the surface of CNC from -1.0 mV to about -30 mV, with the increment of the reaction time from 20 min to 45 min, which proved the higher stability of CNC suspension. Crystallinity increased from 80% to 90% when the reaction time was increased from 20 to 45 min, respectively, while a crystallite size from 2.705 to 4.56 nm was obtained with an increment of the acid concentration. Acid hydrolysis enhanced crystallinity but attenuated the temperature corresponding to major decomposition (Tmax) at 260 °C and the beginning of degradation (Ti) at 200 °C due to the attachment of SO₄^2- ions on the surface, which decreased the thermal stability of CNC. The second degradation at 360 °C indicated the stable crystal structure of CNC. The endothermic peak at 255 °C in the DTA study provided evidence of sulfated nanocrystal decomposition and the recrystallization of cellulose I to cellulose II, the most stable structure among the other four celluloses. The proposed easy-to-reproduce method can successfully and efficiently produce CNCs from waste jute fibers in a straightforward way.

Antibody Immobilization on Sulfated Cellulose Nanocrystals

Exploiting cellulose nanocrystals' high aspect ratio and tailorable surface for immunological biosensors has been hindered by the relatively limited research on using commonly available sulfated cellulose nanocrystals (CNCs) for antibody immobilization and by the low hydrolytic stability of dried assemblies produced from sulfated CNCs. Herein, we report a reaction scheme that enables both hydrolytic stability and antibody immobilization through 3-aminopropyl-triethoxysilane and glutaric anhydride chemistry. Immobilization was demonstrated using three model antibodies used in the detection of the cancer biomarkers: alpha-fetoprotein, prostate-specific antigen, and carcinoembryonic antigen. Thermogravimetric analysis coupled with Fourier-transform infrared spectroscopy provided evidence of CNC modification. Quartz crystal microbalance with dissipation monitoring was used to monitor binding during each step of the immobilization scheme as well as binding of the corresponding antigens. The general reaction scheme was tested using both aqueous CNC dispersions and CNC films. Film modification is slightly simpler as it avoids centrifugation and washing steps. However, modifying the dispersed CNCs provides access to their entire surface area and results in a greater capacity for antigen binding.

Influences of modified fiber inclusion with varying particle size on corn starch-based extrudate expansion

The inclusion of cellulose nanocrystals (CNC) and microcrystalline cellulose (MCC) during extrusion processing of corn starch (CS) is presented in this study. Blends were prepared by incorporating CNC and MCC at different concentrations, 1%, 3%, 5%, and 10% w/w in CS. The crystallinity index (CrI) of CNC and MCC was determined using X-ray diffraction, and the chemical functionality of CNC, MCC, and CS was studied using Fourier transform infrared spectroscopy. The pasting properties of the blends were studied using Micro Visco-Amylo-Graph before extrusion. The blends were preconditioned to 18 ± 0.5% (w.b.) moisture and extruded using a twin-screw extruder at 200 and 250 rpm at 140°C. CS-CNC's expansion ratio (ER) values were 2.95 to 3.35 and 2.72 to 3.22 for MCC. CNC's CrI and particle size were significantly lower than MCC, allowing CNC-based extrudates to have ER values similar to the control even at high CNC concentration (≤10% w/w). This study demonstrated that fiber with particle size <100 µm can be added in direct-expanded product formulations at high concentrations without negatively influencing the extrudate texture while offering increased nutritional value. PRACTICAL APPLICATION: This study gives insight into the potential application of cellulose nanocrystals and microcrystalline cellulose in manufacturing direct-expanded extruded products, providing high fiber content without compromising the product quality. This knowledge could also be translated into manufacturing other food products such as breakfast cereals, pasta, and bread.