Surface tension isotherms, adsorption dynamics and dilational visco-elasticity of sodium dodecyl sulphate solutions

Interfacial property determination from dynamic pendant-drop characterizations

The properties of the interface between materials have practical implications in various fields, encompassing capillary action, foam and emulsion stability, adhesion properties of materials and mass and heat transfer processes. Studying the dynamics of interfaces is also fundamental for understanding intermolecular interactions, change of molecular conformations and molecular aggregations. Pendant-drop tensiometry and its extension, the oscillating drop method, are simple, versatile methods used to measure surface tension, interfacial tension and interfacial rheological properties. These methods can, however, generate unreliable results because of inadequate material preparation, an incorrect calibration method, inappropriate selection of data for analysis, neglect of optical influences or operating the system outside the linear viscoelastic regime. In addition, many studies fail to report accurate uncertainties. This protocol addresses all these critical points and provides detailed descriptions of some operation tips relating to purifying methods for different kinds of material, the time frame for analyzing measurement data, the correction method for optical effects, implementation of the oscillating method with a common programmable pump and remedies for some common problems encountered during the measurement. Examples of interfacial tension measurements for two- and three-phase systems, as well as interfacial dilational modulus measurements for N2 and surfactant solutions, are provided to illustrate procedural details and results. A single measurement takes minutes to hours to complete, while the entire protocol, including the leak test, cleaning, repeated measurements and data analysis, may take several days.

Chitosan-Surfactant Composite Nanocoatings on Glass and Zinc Surfaces Prepared from Aqueous Solutions

Hydrophobic coatings from chitosan-surfactant composites (ca. 400 nm thick by UV-Vis spectroscopy) for possible corrosion protection were developed on glass and zinc substrates. The surfactants (sodium dodecyl sulfate, SDS or sodium dodecylbenzenesulfonate, and SDBS) were added to the chitosan by two methods: mixing the surfactants with the aqueous chitosan solutions before film deposition or impregnating the deposited chitosan films with surfactants from their aqueous solutions. For the mixed coatings, it was found that the lower surface tension of solutions (40-45 mN/m) corresponded to more hydrophobic (80-90°) coatings in every case. The hydrophobicity of the impregnated coatings was especially significant (88° for SDS and 100° for SDBS). Atomic force microscopy studies revealed a slight increase in roughness (max 1.005) for the most hydrophobic coatings. The accumulation of surfactants in the layer was only significant (0.8-1.0 sulfur atomic %) in the impregnated samples according to X-ray photoelectron spectroscopy. Polarization and electron impedance spectroscopy tests confirmed better barrier properties for these samples (40-50% pseudo-porosity instead of 94%). The degree of swelling in a water vapor atmosphere was significantly lower in the case of the impregnated coatings (ca. 25%) than that of the native ones (ca. 75%), measured by spectroscopic ellipsometry. Accordingly, good barrier layer properties require advantageous bulk properties in addition to surface hydrophobicity.

Stratification and film ripping induced by structural forces in granular micellar thin films

HYPOTHESIS

Interactions across incredibly thin layers of fluids, known as thin films, underpin many important processes involving colloids, such as wetting-dewetting phenomena. Often in these systems, thin films are composed of complex fluids that contain dispersed components, such as spherical micelles, giving rise to oscillatory structural forces due to preferential layering under confinement. Modelling of thin film dynamics involving Derjaguin-Landau-Verwey-Overbeek (DLVO) type forces has been widely reported using the Stokes-Reynolds-Young-Laplace (SRYL) model, and we hypothesize that this theory can be extended to a concentrated micellar system by including an oscillatory structural force term in the disjoining pressure.

EXPERIMENTS

We study the drainage behaviour of thin films comprising sodium dodecyl sulfate (SDS) micelles across a range of concentrations and interaction conditions between an air bubble and a mica disk using a custom-built dual-wave interferometry apparatus.

FINDINGS

Early-stage film behaviour is dominated by hydrodynamics, which can be well reproduced by the SRYL model. However, experimental profiles drain significantly faster than predicted, transitioning into a structural force dominated phase characterised by four types of film ripping instabilities that we term 'waving', 'ridging', 'webbing', and 'hole-sheeting'. These instabilities were mapped according to SDS concentration and approach velocity, providing insight into the interplay between structural forces and hydrodynamic conditions.

High Interfacial Viscoelasticity of Aqueous Mixed Dodecyltrimethylammonium Bromide-Sodium Dodecyl Sulfate Surfactants Forming Inclusion Complexes with α-Cyclodextrin

Mixtures of anionic-cationic surfactants have shown high synergistic effects in the bulk solution and at the liquid/air interface. These studies have been limited to a reduced concentration range, where there is no formation of aggregates or precipitates. The addition of host molecules, such as cyclodextrins, to these systems reduces the effects of precipitation by forming inclusion complexes and also modifies the values of other surfactant properties, like the Krafft temperature and the critical aggregation concentration (CAC). We studied the interfacial synergistic effects promoted by electrostatic interactions, using the Rosen model to calculate an interaction parameter for mixtures of sodium dodecyl sulfate (SDS) and dodecyltrimethylammonium bromide (DTAB) in the presence of α-cyclodextrin (αCD), in aqueous solutions. We measured the CAC of SDS-DTAB-αCD mixtures using a pendant drop tensiometer, with the αCD concentration fixed at 10 mM and at 283.15 K. We performed rheological measurements on the mixtures where the surfactant total concentration is fixed below the measured CAC, varying the αCD concentration and temperature. We found that the dilatational modulus shows a clear correlation with the interaction parameter. It appears that the attractive interactions within the film are those due to the inclusion complexes formed by two αCD and one surfactant molecule, which according to the previous studies, is the dominant species in both the bulk and liquid/air interface. The synergistic effect observed here for SDS-DTAB surfactant mixtures with αCD can be applied to systems and processes (drop emission, drug delivery methods, stabilization of viral capsids and bacterial membranes, and emulsification) where interfacial processes require specific viscoelastic properties.

Using foam fractionation to estimate PFAS air-water interface adsorption behaviour at ng/L and µg/L concentrations

PFAS are biologically recalcitrant compounds that are persistent in the environment and have subsequently contaminated groundwater, landfill leachate and surface water. Due to their persistence and toxicity, there are environmental concentration limits imposed on some PFAS compounds that extend down to a few nanograms per litre and even proposals for reducing these to picogram per litre levels. Since PFAS concentrates at water-air interfaces as a result of their amphiphilic nature, this characteristic is important for the successful modelling and prediction of transport behaviour of PFAS through various systems. Here we present a procedure for using a foam fractionation method to experimentally determine the PFAS adsorption behaviour at ng/L and µg/L concentrations in the presence of salts. The equilibrium air-water adsorption coefficients for PFHxS and PFOA at different salinities and concentrations are experimentally shown to be constant across the range of PFAS concentrations investigated (approx. 0.1-100 µg/L). The adsorption isotherms may consequently be modelled by Henry or Langmuir style equations at these low concentrations.

Effect of Divalent and Monovalent Salts on Interfacial Dilational Rheology of Sodium Dodecylbenzene Sulfonate Solutions

This study presents the equilibrium surface tension (ST), critical micelle concentration (CMC) and the dilational viscoelasticity of sodium dodecylbenzene sulfonate (SDBS)-adsorbed layers in the presence of NaCl, KCl, LiCl, CaCl2 and MgCl2 at 0.001–0.1 M salt concentration. The ST and surface dilational viscoelasticity were determined using bubble-shape analysis technique. To capture the complete profile of dilational viscoelastic properties of SDBS-adsorbed layers, experiments were conducted within a wide range of SDBS concentrations at a fixed oscillating frequency of 0.01 Hz. Salts were found to lower the ST and induce micellar formation at all concentrations. However, the addition of salts increased dilational viscoelastic modulus only at a certain range of SDBS concentration (below 0.01–0.02 mM SDBS). Above this concentration range, salts decreased dilational viscoelasticity due to the domination of the induced molecular exchange dampening the ST gradient. The dilational viscoelasticity of the salts of interest were in the order CaCl2 > MgCl2 > KCl > NaCl > LiCl. The charge density of ions was found as the corresponding factor for the higher impact of divalent ions compared to monovalent ions, while the impact of monovalent ions was assigned to the degree of matching in water affinities, and thereby the tendency for ion-pairing between SDBS head groups and monovalent ions.

Contamination in Sodium Dodecyl Sulfate Solutions: Insights from the Measurements of Surface Tension and Surface Rheology

The presence of contamination in sodium dodecyl sulfate (SDS) solutions in the form of dodecanol (LOH) is known to drastically affect the resulting interfacial properties such as surface tension (SFT) and rheology. Dodecanol molecules, which are the product of SDS hydrolysis and are inherently present in SDS solutions, have higher surface activity compared to SDS because they are less soluble in water. A characteristic dip in the SFT isotherm is an indicator of the dodecanol contamination in the sample. The presence of an electrolyte in the solution impacts the surface activity of SDS and its critical micelle concentration, and could yield SFT isotherms that closely match those obtained for pure SDS samples. The interpretation of the isotherms in such cases could thus lead to misinterpretation of the surface purity. In this work, we have examined the SFT isotherms for SDS solutions in both the absence and presence of electrolyte. We have fitted the isotherms to three different thermodynamic adsorption models to estimate the amount of dodecanol present in the sample. We have applied the estimated values for the LOH content in a two-component rheological model to predict the viscoelasticity of such surfactant-laden surfaces. We have compared these results with the experimentally measured interfacial rheological properties. Our findings demonstrate that the presence of impurities can be captured under dynamic expansion and contractions, even for solutions containing background electrolyte.

Unification of surface tension isotherms of PFOA or GenX salts in electrolyte solutions by mean ionic activity

The surface tension isotherms of soluble salts of per- and polyfluoroalkyl substances (PFAS) in electrolyte solutions are typically reported as functions of the PFAS concentration. However, for univalent salts and electrolytes, the Langmuir-Szyszkowski equation is a function of the mean ionic activity a*. Using previously reported data, we show that for salts of perfluorooctanoic acid (PFOA) or hexafluoropropylene oxide dimer acid (GenX™), use of a* rather than concentration provides a unified surface tension isotherm, independent of the electrolyte concentration. This suggests that the electrolyte dependence of the isotherm arises purely from its effect on PFAS activity, rather than an intrinsic surface property. This finding has important implications for the understanding of PFAS retention in saline unsaturated soils, and for PFAS extraction from saline waters by foam fractionation.

Thermodynamics, Kinetics and Dilational Visco-Elasticity of Adsorbed CnEOm Layers at the Aqueous Solution/Air Interface

The adsorption behaviour of linear poly(oxyethylene) alkyl ether (CnEOm) is best described by a reorientation model. Based on a complete set of experimental data, including the adsorption kinetics, the equilibrium surface tension isotherm and the surface dilational visco-elasticity, the thermodynamic and kinetic adsorption parameters for some CnEOm at the water/air interface were determined. For the study, six CnEOm surfactants were selected (n = 10, 12 and 14 and m = 4, 5 and 8) and were studied by bubble profile analysis and maximum bubble pressure tensiometry. A refined theoretical model based on a reorientation-adsorption model combined with a diffusion-controlled adsorption kinetics and exchange of matter allowed us to calculate the surface layer composition by adsorbing molecules in different orientations. It turns out that at larger surface coverage, the adsorption rate decreases, i.e., the apparent diffusion coefficients are smaller. This deceleration can be explained by the transition of molecules adsorbed in a state of larger molar surface area into a state with smaller molar surface area.

Bubble Attachment to Cellulose and Silica Surfaces of Varied Surface Energies: Wetting Transition and Implications in Foam Forming

To better understand the complex system of wet foams in the presence of cellulosic fibers, we investigate bubble-surface interactions by following the effects of surface hydrophobicity and surface tension on the contact angle of captive bubbles. Bubbles are brought into contact with model silica and cellulose surfaces immersed in solutions of a foaming surfactant (sodium dodecyl sulfate) of different concentrations. It is observed that bubble attachment is controlled by surface wetting, but a significant scatter in the behavior occurs near the transition from partial to complete wetting. For chemically homogeneous silica surfaces, this transition during bubble attachment is described by the balance between the energy changes of the immersed surface and the frictional surface tension of the moving three-phase contact line. The situation is more complex with chemically heterogeneous, hydrophobic trimethylsilyl cellulose (TMSC). TMSC regeneration, which yields hydrophilic cellulose, causes a dramatic drop in the bubble contact angle. Moreover, a high interfacial tension is required to overcome the friction caused by microscopic (hydrophilic) pinning sites of the three-phase contact line during bubble attachment. A simple theoretical framework is introduced to explain our experimental observations.

Dynamic Viscosity, Surface Tension and Wetting Behavior Studies of Paraffin–in–Water Nano–Emulsions

This work analyzes the dynamic viscosity, surface tension and wetting behavior of phase change material nano–emulsions (PCMEs) formulated at dispersed phase concentrations of 2, 4 and 10 wt.%. Paraffin–in–water samples were produced using a solvent–assisted route, starting from RT21HC technical grade paraffin with a nominal melting point at ~293–294 K. In order to evaluate the possible effect of paraffinic nucleating agents on those three properties, a nano–emulsion with 3.6% of RT21HC and 0.4% of RT55 (a paraffin wax with melting temperature at ~328 K) was also investigated. Dynamic viscosity strongly rose with increasing dispersed phase concentration, showing a maximum increase of 151% for the sample containing 10 wt.% of paraffin at 278 K. For that same nano–emulsion, a melting temperature of ~292.4 K and a recrystallization temperature of ~283.7 K (which agree with previous calorimetric results of that emulsion) were determined from rheological temperature sweeps. Nano–emulsions exhibited surface tensions considerably lower than those of water. Nevertheless, at some concentrations and temperatures, PCME values are slightly higher than surface tensions obtained for the corresponding water+SDS mixtures used to produce the nano–emulsions. This may be attributed to the fact that a portion of the surfactant is taking part of the interface between dispersed and continuous phase. Finally, although RT21HC–emulsions exhibited contact angles considerably inferior than those of distilled water, PCME sessile droplets did not rapidly spread as it happened for water+SDS with similar surfactant contents or for bulk–RT21HC.

Determining the surface dilational rheology of surfactant and protein films with a droplet waveform generator

Understanding rheological properties of surfactant and protein films plays a crucial role in a variety of industrial and research areas, such as food processing, cosmetics, and pharmacology. To determine the surface dilational modulus using drop shape analysis, one needs to measure the dynamic surface tension in response to a sinusoidal oscillation of the surface area of the droplet. Despite many applications of drop shape analysis in studying interfacial rheology, oscillation of the droplet surface area is usually controlled in an indirect manner. Existing methods are only capable of controlling volume oscillations of the droplet rather than its surface area. We have developed an arbitrary waveform generator (AWG) to directly oscillate the surface area of a millimeter-sized droplet in a predefined sinusoidal waveform. Here, we demonstrated the capacity of this AWG, in conjunction with constrained drop surfactometry (CDS), in studying the surface dilational rheology of adsorbed surfactant and protein films. It is found that the surface dilational modulus determined for a dilute surfactant (C₁₂DMPO) and two protein solutions (bovine serum albumin and β-casein) revealed their adsorption mechanisms. Our methods hold promise in studying the interfacial rheology of various thin-film materials, biomembranes, foams, and emulsions.

Adsorption of Sodium Dodecyl Sulfate at Water-Dodecane Interface in Relation to the Oil in Water Emulsion Properties

The control of the behavior of oil in water emulsions requires deeper investigations on the adsorption properties of the emulsion stabilizers at the interfaces, which are fundamental to explain the (de)stabilization mechanisms. In this work, we present an extensive study on oil-in-water emulsions stabilized by sodium dodecyl sulfate (SDS) below its critical micellar concentration. Dynamic tensiometry, dilational rheology, and electrical conductivity measurements are used to investigate the adsorption properties at the droplet interface, whereas the aging of the respective emulsions was investigated by monitoring the macroscopic thickness of the emulsion layer, by microimaging and dynamic light scattering (DLS) analysis, to get information on the drop size distribution. In addition, the droplet coalescence is investigated by a microscopy setup. The results of this multitechnique study allow deriving a coherent scenario where the adsorption properties of this ionic surfactant relate to those of the emulsion, such as, for example, the prevention of droplet coalescence and the presence of other mechanisms, such as Ostwald ripening, responsible for the emulsion aging.

The surface rheological signature of the geometric isomers of an azobenzene-surfactant

The equilibrium and dynamic surface properties of a photosensitive azobenzene-surfactant subject to illumination with UV and Vis-light leading to the respective geometric cis- and trans-isomers were studied. The adsorption layers formed by the soluble surfactant were characterized by pendant drop tensiometry and surface rheology using the oscillating bubble technique. Aqueous solutions corresponding to the geometric isomers could clearly be distinguished in terms of both their equilibrium and dynamic surface properties. The frequency dependence of the surface dilatational modulus could be described by the extended Lucassen-van den Tempel (LvdT)-model. These findings can be interpreted in terms of the changes of the dipole moment. Furthermore, they shed some light on the relation between the molecular structure and macroscopic properties of the adsorption layer.

Dynamic interfacial tension of surfactant solutions

The dynamics of surfactant interfacial layers was first discussed more than a century ago. In 1946 the most important work by Ward and Tordai was published which is still the theoretical basis of all new models to describe the time dependence of interfacial properties. In addition to the diffusion controlled adsorption mechanism, many other models have been postulated in literature, however, well performed experiments with well defined surfactant systems have shown that the diffusional transport is the main process governing the entire formation of surfactant adsorption layers. The main prerequisite, in addition to the diffusional transport, is the consideration of the right boundary condition at the interface, given by a respective equation of state. In addition to the classical models of Langmuir and Frumkin, also the so-called reorientation or interfacial aggregation models are to be assumed to reach a quantitative description of respective experimental data. Moreover, the adsorption of surfactants at the interface between water and a gas phase different from air can be strongly influenced by the type of molecules within the gas phase, such as alkane vapours. These oil molecules co-adsorb from the gas phase and change the adsorption kinetics strongly. Besides the discussion of how to apply theoretical adsorption kinetics models correctly, a large number of experimental data are presented and the way of a quantitative analysis of the adsorption mechanism and the main characteristic parameters is presented. This includes micellar solutions as well as mixtures of surfactants of ionic and non-ionic nature.

Photoresponsive Foams Generated by a Rigid Surfactant Derived from Dehydroabietic Acid

Innovation in the structure of surfactants is crucial to the construction of a surfactant-based system with intriguing properties. With dehydroabietic acid as a starting material, a nearly totally rigid azobenzene surfactant (R-azo-Na) was synthesized. The trans-R-azo-Na formed stable foams with half-lives of 636, 656, 976, and 872 min for 0.3, 1, 2, and 4 mmol·L^-1 aqueous solutions, respectively. Under UV light irradiation, a fast collapse of the foams was observed, showing an in situ response. The excellent foam stability of trans-R-azo-Na leads to the extremely high photoresponsive efficiency. As revealed by dynamic surface tension and pulsed-field gradient NMR methods, an obvious energy barrier existed in the adsorption/desorption process of trans-R-azo-Na on the air/water interface. The foams formed by trans-R-azo-Na are thus stable against coarsening processes. The results reveal the unique photoresponsive behavior of a surfactant with a rigid hydrophobic skeleton and provide new insights into the structure causing aggregation of surfactants.

Adsorption of ionic surfactants at microscopic air-water interfaces using the micropipette interfacial area-expansion method: Measurement of the diffusion coefficient and renormalization of the mean ionic activity for SDS

The dynamic adsorption of ionic surfactants at air-water interfaces have been less-well studied than that of the simpler non-ionics since experimental limitations on dynamic surface tension (DST) measurements create inconsistencies in their kinetic analysis. Using our newly designed "Micropipette interfacial area-expansion method", we have measured and evaluated both equilibrium and dynamic adsorption of a well-known anionic surfactant, sodium dodecyl sulphate (SDS), in the absence or presence of 100mM NaCl. Our focus was to determine if and to what extent the inclusion of a new correction parameter for the "ideal ionic activity", A_±i, can renormalize both equilibrium and dynamic surface tension measurements and provide better estimates of the diffusion coefficient of ionic surfactants in aqueous media obtained from electroneutral models, namely extended Frumkin isotherm and Ward-Tordai adsorption models. We found that the estimated value of the new parameter, A_±i=0.29, is key to obtain the diffusion coefficient D=5.3±0.3×10^-6cm²/s for SDS, in excellent agreement with the literature. These new technique and analyses can now be applied to study the interfacial adsorption of a range of both ionic and non-ionic surface-active molecules, including the potentially slower-diffusing polymers and biological materials like lipids, peptides, and proteins.

Effect of surfactants on surface activity and rheological properties of type I collagen at air/water interface

We describe the effect of three synthetic surfactants (anionic - sodium dodecyl sulfate (SDS), cationic - cetyltrimethylammonium bromide (CTAB) and nonionic - Triton X-100 (TX-100)) on surface properties of the type I calf skin collagen at the air/water interface in acidic solutions (pH 1.8). The protein concentration was fixed at 5×10^-6molL^-1 and the surfactant concentration was varied in the range 5×10^-6molL^-1-1×10^-4molL^-1, producing the protein/surfactant mixtures with molar ratios of 1:1, 1:2, 1:5, 1:10 and 1:20. An Axisymmetric Drop Shape Analysis (ADSA) method was used to determine the dynamic surface tension and surface dilatational moduli of the mixed adsorption layers. Two spectroscopic techniques: UV-vis spectroscopy and fluorimetry allowed us to determine the effect of the surfactants on the protein structure. The thermodynamic characteristic of the mixtures was studied using isothermal titration calorimetry (ITC) and differential scanning calorimetry (DSC). Modification of the collagen structure by SDS at low surfactant/protein ratios has a positive effect on the mixture's surface activity with only minor deterioration of the rheological properties of the adsorbed layers. The collagen/CTAB mixtures do not show that pronounced improvement in surface activity, while rheological properties are significantly deteriorated. The mixtures with non-ionic TX-100 do not show any synergistic effects in surface activity.

Relevance of interfacial viscoelasticity in stability and conformation of biomolecular organizates at air/fluid interface

Soft materials are complex macromolecular systems often exhibiting perplexing non-Newtonian viscoelastic properties, especially when the macromolecules are entangled, crowded or cross-linked. These materials are ubiquitous in the biology, food and pharma industry and have several applications in biotechnology and in the field of biosensors. Based on the length scales, topologies, flexibility and concentration, the systems behave both as liquids (viscous) and solids (elastic). Particularly, for proteins and protein-lipid systems, viscoelasticity is an important parameter because it often relates directly to stability and thermodynamic interactions of the pure biological components as well as their mixtures. Despite the large body of work that is available in solution macro-rheometry, there are still a number of issues that need to be addressed in dealing with proteins at air/fluid interfaces and with protein-polymer or protein-lipid interfaces that often exhibit very low interfacial viscosity values. Considering the important applications that they have in biopharmaceutical, biotechnological and nutraceutical industries, there is a need for developing methods that meet the following three specific issues: small volume, large dynamic range of shear rates and interfacial properties of different biomolecules. Further, the techniques that are developed should include Newtonian, shear thinning and yielding properties, which are representative of the different solution behaviors typically encountered. The review presented here is a comprehensive account of the rheological properties of different biomolecules at air/fluid and solid/fluid interfaces. It addresses the usefulness of 'viscoelasticity' of the systems at the interfaces analyzed at the molecular level that can be correlated with the microscopic material properties and touches upon some recent techniques in microrheology that are being used to measure the unusually low viscosity values sensitively.

Dilational Viscoelasticity of Adsorption Layers Measured by Drop and Bubble Profile Analysis: Reason for Different Results

The dilational viscoelasticity of adsorption layer was measured at different frequencies of drop and bubble surface area oscillations for aqueous C12EO5 solutions. The modulus values obtained by the two experimental protocols are the same for Π < 15 mN/m, while for higher surface pressures the values from drop experiments exceed those from bubble profile analysis. The nature of this phenomenon was studied using stress deformation experiments. At high surfactant concentrations the magnitude of surface tension variations is essentially higher for drops as compared with bubbles, leading to an increased viscoelasticity modulus for oscillating drops. The observed effects are analyzed quantitatively using a diffusion controlled exchange of matter model. The viscoelasticity moduli for a number of surfactants (different CnEOm and Tritons, C13DMPO, and SDS) are reported, and it is shown that the discrepancies between the data obtained by the two methods for many surfactants agree well with the predictions made here.

Interfacial equation of state for ionized surfactants at oil/water interfaces

A new mathematical approach has been developed for describing the interfacial behaviour of oil/water interfaces in the presence of ionic surfactants. The approach relies on the ideal behaviour of ionized surfactants at oil/water interfaces, which is previously demonstrated by Lucassen-Reynders (J. Phys. Chem., 1966, 70, 1777-1785). The new derived equation simply relates the interfacial tension to the surfactant molecular size and the cmc value of the surfactant in the aqueous phase. The predicted values are in a reasonable agreement with the measured experimental data. Formation of complex multi-layers is considered and the related development is performed. It is shown that, assuming a multi-layer interface, the proposed model gives an area per surfactant molecule similar to the values obtained by techniques such as neutron reflectivity (NR), while a monolayer assumption yields about half the value. The discussion describes the impact of dissolved oil and ionic components on the interfacial tension of the ionized surfactants at oil/water interfaces.

Properties of polidocanol foam in view of its use in sclerotherapy

Foam sclerotherapy is a widely used method to treat varicose veins disease. It is easy to use and apply, affordable, and has high efficiency that depends on foam stability upon injection. Since sclerotherapy is usually applied in a medical doctor's office, one of the most employed methods to generate foam is based on the Tessari technique which uses pumping cycles of liquid and air in-and-out of a double syringe system. Finally, the produced foam exits through a small orifice (∼2mm) at the output of a three-way valve. The present work shows results regarding the factors that may influence foam stability (liquid to air ratio, type of connector, syringe diameter, number of pumping cycles, etc.) of a commonly used sclerosing agent (polidocanol). Furthermore, an effort is made to evaluate the effect of adding different substances on the stability of polidocanol foams (0.5% w/w) by altering the surface tension or/and the bulk and interfacial rheological properties of the fluids. It is shown that adding small concentrations of nonionic surfactants can increase foam stability with just a very small variation of the mean bubbles size.

Surfactant induced complex formation and their effects on the interfacial properties of seawater

The effect of a cationic surfactant, hexadecyltrimethylammonium bromide (CTAB), on the interfacial properties of seawater has been studied by dynamic and equilibrium surface tension and by dilational rheology essays. Important modifications of the surface tension and dilational rheology response have been observed already at the very low CTAB concentrations, where the effects due to the high ionic strength are negligible. The comparison with the effects of CTAB in different seawater models, or in natural seawater fractions, points out the establishment of strong interactions between the surfactant molecules and the lipophilic fraction of organic material dispersed/dissolved in seawater, affecting the interfacial activity of the molecules. Considering the biochemical richness of seawater, these results can be explained assuming interaction mechanisms and adsorption schemes similar to those speculated for protein and other macromolecules in the presence of surfactants, which in fact show similar features. Thus already at the low concentrations the surfactant molecules form highly surface-active complexes with part of the organic fraction of seawater. At the larger surfactant concentrations these complexes compete for adsorption with an excess of free CTAB molecules which, according to the thermodynamic conditions, are most favoured to occupy the liquid interface. The results of this study underline the important role of the sea organic content in enhancing the surface-activity of surfactants, which is relevant for a deeper understand of the direct and indirect effects of these types of pollutants on the physico-chemical environment in the sea coastal areas and develop mitigation strategies.

Super-elastic air/water interfacial films self-assembled from soluble surfactants

We show that water-soluble monosodic salts of F-alkyl phosphates C(n)F(2n+1) (CH2)2OP(O)(OH)2, with n=8 and 10 (F8H2Phos and F10H2Phos) form Gibbs films with exceptionally high dilational viscoelastic modules E that reach ~900 mN m(-1) in the condensed phases. These E values are up to one order of magnitude larger than those recorded for phospholipid, protein and polymer films commonly considered as highly viscoelastic. F8H2Phos.1Na undergoes a transition between a liquid-expanded and a liquid-condensed phase. In the case of F10H2Phos.1Na, a transition occurs between a gas phase of surface domains, in which the molecules are densely packed, and a liquid-condensed phase.