Preparation and characterization of pH-responsive hydrogel magnetite nanocomposite

Preparation and Characterization of Fe3O4/Poly(HEMA-co-IA) Magnetic Hydrogels for Removal of Methylene Blue from Aqueous Solution

In the present study, Fe3O4/poly(2-hydroxyethyl methacrylate-co-itaconic acid) magnetic hydrogels (MHGs) were prepared by in situ synthesis of Fe3O4 magnetic particles in hydrogels (HGs). The resulting magnetic hydrogels were characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), a vibrating sample magnetometer (VSM), scanning electron microscopy (SEM), and N2 adsorption-desorption. The effect of Fe3O4 on the swelling behavior and adsorption of methylene blue (MB) dye of the prepared hydrogel was studied. Parameters such as the dose, pH, contact time, and MB initial concentration were investigated. The results show that 75% (HG) and 91% (MHG) of MB (200 mg/L) were removed at doses of 2 mg/mL and 1 mg/mL, respectively, under a pH of 6.8 and a contact time of 10 min. The adsorption behavior followed the Langmuir isotherm model, indicating that the adsorption process takes place in monolayers and on homogeneous surfaces. The Langmuir capacities for MB adsorption using the HGs and MHGs were 78 and 174 mg/g, respectively. The adsorption kinetics followed a pseudo-second-order kinetic model. In addition, thermodynamic studies carried out show that the adsorption process is spontaneous and endothermic. Adsorption-desorption studies indicate that the magnetic hydrogel can remove MB for four cycles with removal efficiencies above 90%. Therefore, a MHG is suitable as an alternative material for MB adsorption.

Poly(acrylic acid-co-acrylamide)/Polyacrylamide pIPNs/Magnetite Composite Hydrogels: Synthesis and Characterization

Novel composite hydrogels based on poly(acrylic acid-co-acrylamide)/polyacrylamide pseudo-interpenetrating polymer networks (pIPNs) and magnetite were prepared via in situ precipitation of Fe³⁺/Fe²⁺ ions within the hydrogel structure. The magnetite formation was confirmed by X-ray diffraction, and the size of the magnetite crystallites was shown to depend on the hydrogel composition: the crystallinity of the magnetite particles increased in line with PAAM content within the composition of the pIPNs. The Fourier transform infrared spectroscopy revealed an interaction between the hydrogel matrix, via the carboxylic groups of polyacrylic acid, and Fe ions, which strongly influenced the formation of the magnetite articles. The composites' thermal properties, examined using differential scanning calorimetry (DSC), show an increase in the glass transition temperature of the obtained composites, which depends on the PAA/PAAM copolymer ratio in the pIPNs' composition. Moreover, the composite hydrogels exhibit pH and ionic strength responsiveness as well as superparamagnetic properties. The study revealed the potential of pIPNs as matrices for controlled inorganic particle deposition as a viable method for the production of polymer nanocomposites.

Rapid preparation of N-CNTs/P(AA-co-AM) composite hydrogel via frontal polymerization and its mechanical and conductive properties

Deep eutectic solvent (DES) was prepared by using acrylic acid (AA) and acrylamide (AM) as hydrogen bonding donors (HBD) and choline chloride (ChCl) as hydrogen bonding receptors (HBA). Nitrogen-doped carbon nanotubes (N-CNTs) were dispersed in DES as fillers, and N-CNTs/P(AA-co-AM) composite hydrogels were prepared by FP. The interaction mode between the hydrogel and N-CNTs was characterized by Fourier infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The mechanical properties, pH response and electrical conductivity of the composite hydrogels were studied. The results showed that the mechanical properties of the hydrogel were significantly enhanced with the increase of N-CNT content. The tensile strength and compressive strength of the FP4 composite hydrogel reached 5.42 MPa and 4.29 MPa, respectively. Due to the dissociation of carboxyl groups in AA in an alkaline environment the composite hydrogel showed excellent pH response performance. The conductivity of the hydrogel was also found to be improved with the content of N-CNTs. When the content of N-CNTs is 1.0 wt%, the conductivity of the hydrogel was 4.2 times higher than that of the hydrogel without N-CNTs, and connecting it to a circuit can make an LED lamp emit bright light. In this study, a simple and green method was proposed to prepare composite hydrogels with excellent mechanical properties and electrical conductivity by FP of DES in less than 5 min.

This study provides a rapid and low-energy method for the preparation of nanocomposite hydrogels with excellent mechanical properties and electrical conductivity.

In situ mechanical reinforcement of polymer hydrogels via metal-coordinated crosslink mineralization

Biological organic-inorganic materials remain a popular source of inspiration for bioinspired materials design and engineering. Inspired by the self-assembling metal-reinforced mussel holdfast threads, we tested if metal-coordinate polymer networks can be utilized as simple composite scaffolds for direct in situ crosslink mineralization. Starting with aqueous solutions of polymers end-functionalized with metal-coordinating ligands of catechol or histidine, here we show that inter-molecular metal-ion coordination complexes can serve as mineral nucleation sites, whereby significant mechanical reinforcement is achieved upon nanoscale particle growth directly at the metal-coordinate network crosslink sites.

Biological organic-inorganic materials, such as self-assembling metal-reinforced mussel holdfast threads, remain a popular source of inspiration for materials design and engineering. Here the authors show that metal-coordinate polymer networks can be utilized as simple composite scaffolds for direct in situ crosslink mineralization.

Target-Specific Superparamagnetic Hydrogel with Excellent pH Sensitivity and Reversibility: A Promising Platform for Biomedical Applications

Superparamagnetism has been widely used for many biomedical applications, such as early detection of inflammatory cancer and diabetes, magnetic resonance imaging (MRI), hyperthermia, etc., whereas incorporation of superparamagnetism in stimulus-responsive hydrogels has now gained substantial interest and attention for application in these fields. Recently, pH-responsive superparamagnetic hydrogels showing the potential use in disease diagnosis, biosensors, polymeric drug carriers, and implantable devices, have been developed based on the fact that pH is an important environmental factor in the body and some disease states manifest themselves by a change in the pH value. However, improvement in pH sensitivity of magnetic hydrogels is a dire need for their practical applications. In this study, we report the distinctly high pH sensitivity of new synthesized dual-responsive magnetic hydrogel nanocomposites, which was accomplished by copolymerization (free-radical polymerization) of two pH-sensitive monomers, acrylic acid (AA) and vinylsulfonic acid (VSA) with an optimum ratio, in the presence of presynthesized superparamagnetic iron oxide nanoparticles (Fe3O4(OH) x ). The monomers contain pH-sensitive functional groups (COO- and SO3 - for AA and VSA, respectively), and they have also been widely used as biomaterials because of the good biocompatibility. The pH sensitivity of the superparamagnetic hydrogel, poly(acrylic acid-co-vinylsulfonic acid), PAAVSA/Fe3O4, was investigated by swelling studies at different pH values from pH 7 to 1.4. Distinct pH reversibility of the system was also demonstrated through swelling/deswelling analysis. Thermal stability, chemical configuration, magnetic response, and structural properties of the system have been explored by suitable characterization techniques. Furthermore, the study reveals a pH-responsive significant change in the overall morphology and packing fraction of iron oxide nanoparticles in PAAVSA/Fe3O4 via energy-dispersive X-ray (EDX) elemental mapping with the field emission scanning electron microscopy (FESEM) study (for freeze-dried PAAVSA/Fe3O4, swelled at different pH values), implying a drastic change in susceptibility and induced saturation magnetization of the system. These important features could be easily utilized for the purpose of diagnosis using magnetic probe and/or impedance analysis techniques.

Fe3O4–PVAc nanocomposites: surface modification of sonochemically prepared magnetite nanoparticles via chemical grafting of poly(vinyl acetate)

In the present study, magnetite nanoparticles (MNPs) were synthesized at room temperature under ultrasonic irradiation.

Investigation of magnetically controlled water intake behavior of Iron Oxide Impregnated Superparamagnetic Casein Nanoparticles (IOICNPs)

Iron oxide impregnated casein nanoparticles (IOICNPs) were prepared by in-situ precipitation of iron oxide within the casein matrix. The resulting iron oxide impregnated casein nanoparticles (IOICNPs) were characterized by Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR), Vibrating sample magnetometer (VSM) and Raman spectroscopy. The FTIR analysis confirmed the impregnation of iron oxide into the casein matrix whereas XPS analysis indicated for complete oxidation of iron (II) to iron(III) as evident from the presence of the observed representative peaks of iron oxide. The nanoparticles were allowed to swell in phosphate buffer saline (PBS) and the influence of factors such as chemical composition of nanoparticles, pH and temperature of the swelling bath, and applied magnetic field was investigated on the water intake capacity of the nanoparticles. The prepared nanoparticles showed potential to function as a nanocarrier for possible applications in magnetically targeted delivery of anticancer drugs.

Templated Synthesis of Magnetic Nanoparticles through the Self-Assembly of Polymers and Surfactants

The synthesis of superparamagnetic nanoparticles (NPs) for various technological applications continues to be an interesting research topic. The successful application of superparamagnetic NPs to each specific area typically depends on the achievement of high magnetization for the nanocrystals obtained, which is determined by their average size and size distribution. The size dispersity of magnetic NPs (MNPs) is markedly improved when, during the synthesis, the nucleation and growth steps of the reaction are well-separated. Tuning the nucleation process with the assistance of a hosting medium that encapsulates the precursors (such as self-assembled micelles), dispersing them in discrete compartments, improves control over particle formation. These inorganic-organic hybrids inherit properties from both the organic and the inorganic materials, while the organic component can also bring a specific functionality to the particles or prevent their aggregation in water. The general concept of interest in this review is that the shape and size of the synthesized MNPs can be controlled to some extent by the geometry and the size of the organic templates used, which thus can be considered as molds at the nanometer scale, for both porous continuous matrices and suspensions.

Synthesis and Characterization of Gelatin-Based Magnetic Hydrogels

A simple preparation of thermoreversible gelatin-based ferrogels in water provides a constant structure defined by the crosslinking degree for gelatin contents between 6 and 18 wt%. The possibility of varying magnetite nanoparticle concentration between 20 and 70 wt% is also reported. Simulation studies hint at the suitability of collagen to bind iron and hydroxide ions, suggesting that collagen acts as a nucleation seed to iron hydroxide aggregation, and thus the intergrowth of collagen and magnetite nanoparticles already at the precursor stage. The detailed structure of the individual ferrogel components is characterized by small-angle neutron scattering (SANS) using contrast matching. The magnetite structure characterization is supplemented by small-angle X-ray scattering and microscopy only visualizing magnetite. SANS shows an unchanged gelatin structure of average mesh size larger than the nanoparticles with respect to gel concentration while the magnetite nanoparticles size of around 10 nm seems to be limited by the gel mesh size. Swelling measurements underline that magnetite acts as additional crosslinker and therefore varying the magnetic and mechanical properties of the ferrogels. Overall, the simple and variable synthesis protocol, the cheap and easy accessibility of the components as well as the biocompatibility of the gelatin-based materials suggest them for a number of applications including actuators.

Novel-porous-Ag0 nanocomposite hydrogels via green process for advanced antibacterial applications

Silver nanoparticles (NPs) antibacterial characteristics were depends on its particle stabilization, particles size and nucleation agent. In this study, we report on green process of porous silver nanocomposite hydrogels for advanced antibacterial applications. The porous poly(acrylamide) (PAM) hydrogels were developed employing sucrose as porogenator. Silver NPs were nucleated with natural biomass Neem (Azadirachta indica) leaf extracts within the porous hydrogel networks. The formation of silver NPs in the porous hydrogels was confirmed by ultraviolet-visible spectroscopy, fourier transform infrared spectroscopy, X-ray diffraction, and thermo gravimetric analysis. Morphological studies done by scanning electron microscopy and transmission electron microscopy showed that the hydrogels were porous in nature and stabilization of NPs, size, and particles shape. The porous PAM silver nanoparticle hydrogels demonstrated excellent antimicrobial activity with significant effect against Escherichia coli, Micrococcus, and Candida albicus. Hence, it was clear that the developed hydrogels can be used effectively for preventing and treating infections.

Facile fabrication and magnetic properties of a one-dimensional magnetite peapod in a lipid nanotube

Magnetite nanoclusters (MNCs) were aligned one-dimensionally in the hollow cavity of a lipid nanotube (LNT) as a peapod using a simple mixing method in an aqueous solution. The electrostatic interaction of the two materials was considerable enough to allow the preparation of a densely packed MNC-LNT peapod composite. The composite was formed at a pH 5.4-6.8, i.e., near the isoelectric point of the MNCs. At a pH 5.4-6.8, there was neither a strong attractive nor repulsive electrostatic interaction between the surface of the MNC and the LNT. The MNCs-capped LNT composites were formed at basic conditions (above a pH 7.8) in which the MNCs and the LNT pushed each other because of their opposite surface charges. The magnetic property measurement revealed that the 1D aligned MNCs in the peapod structure had a much higher coercivity (10.6 Oe) than the bulk randomized MNCs (5.8 Oe).

Multiresponsive polymer conetworks capable of responding to changes in pH, temperature, and magnetic field: synthesis, characterization, and evaluation of their ability for controlled uptake and release of solutes

This study deals with the preparation of novel multiresponsive (magnetoresponsive, thermoresponsive and pH-responsive) nanocomposite conetworks consisting of oleic acid-coated magnetite nanoparticles (OA·Fe(3)O(4)), hydrophilic/thermoresponsive hexa(ethylene glycol) methyl ether methacrylate (HEGMA), hydrophobic/metal binding 2-(acetoacetoxy)ethyl methacrylate (AEMA), and pH-responsive/thermoresponsive N-diethylaminoethyl methacrylate (DEAEMA) and 2-(dimethylamino)ethyl methacrylate (DMAEMA) moieties. Conventional free radical copolymerization was employed for the synthesis of random conetworks in the absence and presence of preformed OA·Fe(3)O(4). Further, in characterization of these materials in regards to their swelling behavior in organic and aqueous solvents, thermal/thermoresponsive properties, and composition, assessment of their magnetic characteristics disclosed tunable superparamagnetic behavior. These systems were also evaluated toward their ability to adsorb and release a solute (benzoic acid) in a controlled manner upon varying the pH.