Dispersion stability of organoclay in octane improved by adding nonionic surfactants

Preparation and Properties of Organically Modified Na-Montmorillonite

This study investigates the montmorillonite (MMT) content, rotational viscosity, and colloidal index of sodium montmorillonite (Na-MMT) as a function of the sodium agent dosage, reaction time, reaction temperature, and stirring time. Na-MMT was modified using different octadecyl trimethyl ammonium chloride (OTAC) dosages under optimal sodification conditions. The organically modified MMT products were characterized via infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, and scanning electron microscopy. The results show that the Na-MMT with good properties (i.e., the maximum rotational viscosity and highest Na-MMT content with no decrease in the colloid index) was obtained at a 2.8% sodium carbonate dosage (measured based on the MMT mass), a temperature of 25 °C, and a reaction time of two hours. Upon organic modification of the optimized Na-MMT, OTAC entered the NA-MMT interlayer, and the contact angle was increased from 20.0° to 61.4°, the layer spacing was increased from 1.58 to 2.47 nm, and the thermal stability was conspicuously increased. Thus, MMT and Na-MMT were modified by the OTAC modifier.

Reaction of decabromodiphenyl ether with organo-modified clay-templated zero-valent iron in water-tetrahydrofuran solution: Nano- to micrometric scale effects

Smectite clay-templated nanoscale zero-valent iron (CZVI) was modified with tetramethylammonium (TMA), trimethylphenylammonium (TMPA) and hexadecyltrimethylammonium (HDTMA) to achieve organoclay-templated ZVI (OCZVI). The reactivity of various OCZVIs was evaluated on the basis of degradation of decabromodiphenyl ether (DBDE) in tetrahydrofuran (THF)-water binary solution. Characterization of OCZVI interlayer at nanometric scale indicated that the clay particles had the domains with three basal spacings in the THF/water solution. In the 50 % THF solution TMPA modification promoted the formation of the domains with a basal spacing at 1.56 nm, which could promote the degradation of DBDE. At the micrometric scale, in the 90 % THF solution TMA and TMPA modification tended to enhance the aggregation of OCZVI particles, while the HDTMA modification reduced the aggregation, and high percentage of modification yielded viscous gel structures. The relatively rapid sedimentation processes in 90 % THF solution (compared to that in 50 % THF solution) and formation gel structures could reduce the access of DBDE to the interlayer reactive nZVIs, and lead to the significant reduction in reaction rate. These results provide important insights to the organo-modification on clays which could alter their orientations and dispersion in organic-water binary solution to achieve the desired reactivity on confined clay surfaces.

How does Pickering Emulsion Pre-treatment Influence the Properties of Wood Flour and its Composites with High-Density Polyethylene?

Silica synergistically stabilized paraffin Pickering emulsion is applied to modify wood flour (WF) for preparing wood/polymer composites. The effect of Pickering emulsion on properties of the WF and its composites with high-density polyethylene (HDPE) is investigated. The impregnation of paraffin Pickering emulsion could significantly improve the WF dispersion in HDPE matrix, resulting in increased melt flow index (MFI). It increased from 1.3 g/10 min (control) to 2.1 g/10 min (Pickering treatment) due to the lubrication of paraffin and rolling friction provided by silica nanoparticles. The hydrophobicity of the WF was improved by the penetration of paraffin and silica in the cell wall, which could consume the hydroxyl groups in WFs via hydrogen bonding. Owing to the well distribution of WFs and silica, the mechanical properties and surface hardness of the composites were enhanced obviously. The optimal tensile strength and impact strength increased 23% (18.28 MPa) and 32% (14.16 KJ/m²), respectively. It also could be attributed to the improved interfacial compatibility due to the incorporation of surfactants (Span 80 and Tween 80), which acted as a coupling agent. Furthermore, the silica incorporated in the WF could compensate the negative effect of paraffin on thermal stability of the composites. A model concerning the interactions in the composites was proposed based on the research results.

Preparation of modified montmorillonite with different quaternary ammonium salts and application in Pickering emulsion

The emulsion stabilized with long-chain quaternary ammonium salt-modified montmorillonite has better stability.