Surface and interface characteristics of hydrophobic lignin derivatives in solvents and films

Exploring chemical reactions to enhance thermal and dispersion stability of kraft and organosolv lignin

Lignin has been overlooked and used as a waste for long due to its complex and partially hydrophobic structure. Many efforts have been carried out to overcome these deficiencies and apply it as a high-value product, which are insufficient to reach the full potential of lignin in various advanced applications, since they require with procedures for the obtaining of more specific and fine-tuned chemical structures. This work focuses on the obtaining of differently structured hydrophilic lignins derived both from Kraft and organosolv isolation processes. The chemical structures of the different lignin types were studied, and the effect of the structural differences in the modification processes and their subsequent properties analyzed, valorizing their potential application for diverse purposes. The carboxymethylation and sulfomethylation reactions were carried out with the aim of enhancing the polarity of the lignin samples, while the methylation reaction aimed to obtain lignins with higher stability. The physicochemical analyses of the samples, carried out by FTIR, GPC, 31P NMR, 13C NMR, and HSQC NMR, verified the effectiveness of the chemical reactions and conditions selected, obtaining lignins with lower hydroxyl content, due to their substitution and insertion of carboxymetyl, sulfomethyl and methyl groups, therefore obtaining more condensed, aromatic and oxygenated aromatic carbon structures. While the methylation reaction was the most efficient in substituting the OH groups, due to its non-selectivity, OL showed higher modification yields than KL. In terms of the thermal and morphological properties, analyzed by DLS and TGA respectively, it was observed that the modified samples showed lower Z potential values, along with higher conductivity, being the sulfomethylated organosolv lignin the one showing the best results, which was also the one with the smallest particle size and polydispersity index. Finally, all the modified samples showed higher T50% values, suggesting a better stability towards degradation.

Characterization of Pickering emulsions stabilized by delipidated egg yolk granular protein nanoparticles crosslinked with ultraviolet radiation

In this study, delipidated egg yolk proteins were used for the first time to prepare nanoparticles by the self-assembling method at pH 8.0, then treated with UV-C as a crosslinking agent, and their stability tested at pH 7.0, which is a more convenient pH for food applications. According to the results obtained, non-irradiated nanoparticles had a size of 431.8 ± 75.7 nm at pH 7.0, but the 10 min UV-C irradiated nanoparticles had an average size of 139.7 ± 5.9 nm. These nanoparticles also showed a high resistance to destabilization by SDS, urea or DTT and noticeable antioxidant and ferrous chelating activities. Pickering emulsions prepared at the nanoparticle concentration of 1 % (w/w) showed the smallest average droplet size and the lowest Turbiscan stability index value after 80 days of storage. All in all, these results have important implications for the utilisation of these proteins as a conventional Pickering emulsifying agent.

Bioethanol lignin-rich residue from olive stones for electrospun nanostructures development and castor oil structuring

This work describes the chemical and structural characterization of a lignin-rich residue from the bioethanol production of olive stones and its use for nanostructures development by electrospinning and castor oil structuring. The olive stones were treated by sequential acid/steam explosion pretreatment, further pre-saccharification using a hydrolytic enzyme, and simultaneous saccharification and fermentation (PSSF). The chemical composition of olive stone lignin-rich residue (OSL) was evaluated by standard analytical methods, showing a high lignin content (81.3 %). Moreover, the structural properties were determined by Fourier-transform infrared spectroscopy, nuclear magnetic resonance, and size exclusion chromatography. OSL showed a predominance of β-β' resinol, followed by β-O-4' alkyl aryl ethers and β-5' phenylcoumaran substructures, high molecular weight, and low S/G ratio. Subsequently, electrospun nanostructures were obtained from solutions containing 20 wt% OSL and cellulose triacetate with variable weight ratios in N, N-Dimethylformamide/Acetone blends and characterized by scanning electron microscopy. Their morphologies were highly dependent on the rheological properties of polymeric solutions. Gel-like dispersions can be obtained by dispersing the electrospun OSL/CT bead nanofibers and uniform nanofiber mats in castor oil. The rheological properties were influenced by the membrane concentration and the OSL:CT weight ratio, as well as the morphology of the electrospun nanostructures.

One-pot synthesis of magnetic cellulose nanocrystal and its post-functionalization for doxycycline adsorption

The composite of magnetite (Fe₃O₄) and cellulose nanocrystal (CNC) is considered a potential adsorbent for water treatment and environmental remediation. In the current study, a one-pot hydrothermal procedure was utilized for magnetic cellulose nanocrystal (MCNC) development from microcrystalline cellulose (MCC) in the presence of ferric chloride, ferrous chloride, urea, and hydrochloric acid. The x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD), and Fourier-transform infrared spectroscopy analysis confirmed the presence of CNC and Fe₃O₄, while transmission electron microscopy (TEM) and dynamic light scattering (DLS) analysis verified their respective sizes (< 400 nm and ≤ 20 nm) in the generated composite. To have an efficient adsorption activity for doxycycline hyclate (DOX), the produced MCNC was post-treated using chloroacetic acid (CAA), chlorosulfonic acid (CSA), or iodobenzene (IB). The introduction of carboxylate, sulfonate, and phenyl groups in the post-treatment was confirmed by FTIR and XPS analysis. Such post treatments decreased the crystallinity index and thermal stability of the samples but improved their DOX adsorption capacity. The adsorption analysis at different pHs revealed the increase in the adsorption capacity by reducing the basicity of the medium due to decreasing electrostatic repulsions and inducing strong attractions.

Enhanced production of sugars and UV-shielded lignin/PAN fiber mats from chemi-mechanical pulps

This study investigated poplar pretreatments by chemi-mechanical pulping (CMP) under different beating degrees and alkali concentrations. The enzyme-mediated hydrolysis of pretreated poplar was enhanced by deacetylation and delignification. Meanwhile, the remaining lignin residues were used to produce lignin/polyacrylonitrile (PAN) fiber mats by electrospinning. These mats exhibited excellent mechanical and UV-blocking performance when the lignin was obtained from pulps under milder alkali concentrations (5 g/L). ³¹P nuclear magnetic resonance (³¹P NMR) and two-dimensional heteronuclear single-quantum correlation nuclear magnetic resonance (2D HSQC NMR) data revealed that increasing the beating degree at low alkali concentration during the CMP process led to the cleavage of β-O-4' interunit linkages and re-condensation in lignin, releasing several phenolic groups. Lignin with more linear β-O-4' interunit linkages and lesser phenolic groups, obtained from treatment of CMP with lower alkali concentration (5 g/L) and beating degree (20°SR), resulted in the corresponding lignin/PAN fiber mats exhibiting better mechanical performance. Further, lignin, along with the increased phenolic-OH and COOH, and p-hydroxybenzoate (PB) units with a more extended conjugate structure, derived from CMP under lower alkali concentration (5 g/L) and higher beating degree (45°SR), led to a stronger ultraviolet (UV) absorption in the corresponding lignin/PAN mats. To summarize, this study reports a mild and low-pollution biomass pretreatment method (CMP) that can efficiently regulate the lignin structure and exhibit efficient anti-ultraviolet properties. The corresponding UV-blocking fiber mats can be potentially used as materials for wearable fabrics.

Effect of Reaction Temperature on Properties of Torrefied Kenaf

Torrefaction is a thermal treatment method used to achieve solid-phase biofuel. Raw biomass generally have low heating value and high moisture content; thus, these characteristics should be enhanced before using it as a fuel. In this study, herbaceous biomass kenaf was torrefied at 220, 260, 300, and 340 °C under nitrogen atmosphere for 30 min to investigate the effect of temperature on its properties. The properties of torrefied kenaf were classified into two groups: physical properties such as mass and energy yields, moisture content, and proximate analysis and chemical properties such as functional groups and chemical compositions of sugars and lignin. The mass and energy yield of torrefied kenaf decreased as the reaction temperature increased. In addition, an increase in carbon content and a rapid decrease in oxygen content were observed in torrefied kenaf, which indicated the degradation of compounds such as hemicellulose and cellulose. Elemental analysis, proximate analysis, thermal analysis, Fourier transform infrared spectroscopy, and chemical composition analysis were performed to further investigate the characteristics of torrefied kenaf.

Different Kraft lignin sources for electrospun nanostructures production: Influence of chemical structure and composition

This work focuses on the structural features and physicochemical properties of different Kraft lignins and how they can influence the electrospinning process to obtain nanostructures. Structural features of Kraft lignins were characterized by Nuclear Magnetic Resonance, Size Exclusion Chromatography, Fourier-transform Infrared Spectroscopy, and thermal analysis, whereas chemical composition was analyzed by standard method. The addition of cellulose acetate (CA) improves the electrospinning process of Kraft lignins (KL). Thus, solutions of KL/CA at 30 wt% with a KL:CA weight ratio of 70:30 were prepared and then physicochemical and rheologically characterized. The morphology of electrospun nanostructures depends on the intrinsic properties of the solutions and the chemical structure and composition of Kraft lignins. Then, surface tension, electrical conductivity and viscosity of eucalypt/CA and poplar/CA solutions were suitable to obtain electrospun nanostructures based on uniform cross-linked nanofibers with a few beaded fibers. It could be related with the higher purity and higher linear structure, phenolic content and S/G ratios of lignin samples. However, the higher values of electrical conductivity and viscosity of OTP/CA solutions resulted in electrospun nanostructure with micro-sized particles connected by thin fibers, due to a lower purity, S/G ratio and phenolic content and higher branched structure in OTP lignin.

Unlocking the secret of lignin-enzyme interactions: Recent advances in developing state-of-the-art analytical techniques

Bioconversion of renewable lignocellulosics to produce liquid fuels and chemicals is one of the most effective ways to solve the problem of fossil resource shortage, energy security, and environmental challenges. Among the many biorefinery pathways, hydrolysis of lignocellulosics to fermentable monosaccharides by cellulase is arguably the most critical step of lignocellulose bioconversion. In the process of enzymatic hydrolysis, the direct physical contact between enzymes and cellulose is an essential prerequisite for the hydrolysis to occur. However, lignin is considered one of the most recalcitrant factors hindering the accessibility of cellulose by binding to cellulase unproductively, which reduces the saccharification rate and yield of sugars. This results in high costs for the saccharification of carbohydrates. The various interactions between enzymes and lignin have been explored from different perspectives in literature, and a basic lignin inhibition mechanism has been proposed. However, the exact interaction between lignin and enzyme as well as the recently reported promotion of some types of lignin on enzymatic hydrolysis is still unclear at the molecular level. Multiple analytical techniques have been developed, and fully unlocking the secret of lignin-enzyme interactions would require a continuous improvement of the currently available analytical techniques. This review summarizes the current commonly used advanced research analytical techniques for investigating the interaction between lignin and enzyme, including quartz crystal microbalance with dissipation (QCM-D), surface plasmon resonance (SPR), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, atomic force microscopy (AFM), nuclear magnetic resonance (NMR) spectroscopy, fluorescence spectroscopy (FLS), and molecular dynamics (MD) simulations. Interdisciplinary integration of these analytical methods is pursued to provide new insight into the interactions between lignin and enzymes. This review will serve as a resource for future research seeking to develop new methodologies for a better understanding of the basic mechanism of lignin-enzyme binding during the critical hydrolysis process.

Electrospun lignin-PVP nanofibers and their ability for structuring oil

This work explores the electrospinnability of low-sulfonate Kraft lignin (LSL)/polyvinylpyrrolidone (PVP) solutions in N,N-dimethylformamide (DMF) and the ability of the different micro- and nano-architectures generated to structure castor oil. LSL/PVP solutions were prepared at different concentrations (8-15 wt%) and LSL:PVP ratios (90:10-0:100) and physico-chemically and rheologically characterized. The morphology of electrospun nanostructures mainly depends on the rheological properties of the solution. Electrosprayed nanoparticles or micro-sized particles connected by thin filaments were obtained from solutions with low LSL/PVP concentrations and/or high LSL:PVP ratios, whereas beaded or bead-free nanofibers were produced by increasing concentration and/or decreasing LSL:PVP ratio, due to enhanced extensional viscoelastic properties and non-Newtonian characteristics. Electrospun LSL/PVP nanofibers are able to form oleogels by simply dispersing them into castor oil at concentrations between 10 and 30 wt%. The rheological properties of the oleogels may be tailored by modifying the LSL:PVP ratio and nanofibers content. The potential application of these oleogels as bio-based lubricants was also explored in a tribological cell. Satisfactory friction and wear results are achieved when using oleogels structured by nanofibers mats with enhanced gel-like properties as lubricants. Overall, electrospinning of lignin/PVP solutions can be proposed as a simple and effective method to produce nanofibers for oil structuring.

Degradable Gelatin-Based Supramolecular Coating for Green Paper Sizing

Developing a paper sizing agent to meet the requirements of low cost, high quality of the paper, and environmental sustainability is significant but remains a challenge. Herein, a novel degradable gelatin-based coating emulsion for paper surface sizing was developed by a simple one-step polymerization and blending process. Poly(methacrylic acid) (PMAA) was first introduced to a gelatin solution to form gelatin-PMAA emulsion (G-PMAA) through the formation of hydrogen bonds between PMAA and gelatin. The addition of PMAA endowed gelatin with the increased hydrophobicity and the decreased upper critical solution temperature. Then, a relatively small amount of the flexible poly(butyl acrylate) (PBA), which imparted the toughness of the formed film, was blended with the G-PMAA emulsion to form G-PMAA/PBA emulsion. The G-PMAA/PBA emulsion with a high gelatin content of 0.2 g/mL was in the sol state at room temperature, which facilitated the application of the G-PMAA/PBA emulsion. The corrugated papers sized by G-PMAA/PBA emulsion exhibited excellent mechanical properties and water resistance.