Efficient removal of high-concentration copper ions from wastewater via 2D g-C3N4 photocatalytic membrane filtration

Application Prospect of Ion-Imprinted Polymers in Harmless Treatment of Heavy Metal Wastewater

With the rapid development of industry, the discharge of heavy metal-containing wastewater poses a significant threat to aquatic and terrestrial environments as well as human health. This paper provides a brief introduction to the basic principles of ion-imprinted polymer preparation and focuses on the interaction between template ions and functional monomers. We summarized the current research status on typical heavy metal ions, such as Cu(II), Ni(II), Cd(II), Hg(II), Pb(II), and Cr(VI), as well as metalloid metal ions of the As and Sb classes. Furthermore, it discusses recent advances in multi-ion-imprinted polymers. Finally, the paper addresses the challenges faced by ion-imprinted technology and explores its prospects for application.

Removal of Iron and Copper Ions and Phenol from Liquid Phase by Membrane Based on Carbonaceous Materials

The present work reports an effective method for the removal of inorganic and organic pollutants using membranes based on different carbonaceous materials. The membranes were prepared based on cellulose acetate (18 wt. %), polyvinylpyrrolidone as a pore-generating agent (2 wt. %) and activated carbon (1 wt. %). Activated carbons were developed from residues after extraction of the mushroom Inonotus obliguus using microwave radiation. It has been demonstrated that the addition of activated carbon to the membranes resulted in alterations to their physical properties, including porosity, equilibrium water content and permeability. Furthermore, the chemical properties of the membranes were also affected, with changes observed in the content of the surface oxygen group. The addition of carbon material had a positive effect on the removal of copper ions from their aqueous solutions by the cellulose-carbon composites obtained. Moreover, the membranes proved to be more effective in the removal of copper ions than iron ones and phenol. The membranes were found to show higher effectiveness in copper removal from a solution of the initial concentration of 800 mg/L. The most efficient in copper ions removal was the membrane containing urea-enriched activated carbon.

Photoelectrocatalytic modification of nanofiltration membranes with SrF2/Ti3C2Tx to simultaneously enhance heavy metal ions rejection and permeability

Heavy metal pollution can significantly harm water systems and human health. Combining photoelectrocatalytic (PEC) and nanofiltration (NF) membrane separation technologies can effectively remove heavy metal ions from wastewater. In this study, a water bath method was used to form SrF2/Ti3C2Tx (ST) nanoparticles on the surface of polyvinylidene fluoride (PVDF) membranes and an additional polyamide (PA) functional layer was formed at the interface by crosslinking. ST@PA composite NF membranes (STPP) with good photocatalytic performance were obtained. The separation and catalytic properties of the STPP membranes were controlled by the ST content, which modifies the surface structure and properties of the membranes. The membrane with optimal ST crosslinking exhibited a water contact angle of 50.8°, pure water flux of 24.6 L·m-2·h-1·bar-1, and rejection rates of Mn2+, Ni2+, Cu2+, and Zn2+ of 98.8%, 95.3%, 95.7%, and 97.3%, respectively, under PEC-assisted separation with visible light illumination from a Xe lamp (300 W) and an applied voltage (2 V). The STPP membranes showed improved rejection rates of heavy metal ions under PEC-assisted operation. The mechanism for the improved membrane performance under PEC conditions was preliminarily clarified considering the relationship between the photocatalytic and filtration properties of STPP membranes along with the influence of light irradiation and an external voltage on the heavy metal ions. The generation of electrons, holes, superoxide radicals, and hydroxyl radicals during membrane operation enhances the rejection rates of heavy metal ions. Based on these results, STPP membranes are considered a promising technology for industrial applications in heavy metal removal.

Preparation of basic magnesium carbonate nanosheets modified pumice and its adsorption of heavy metals

Heavy metal pollution in wastewater poses a grave danger to the environment and the human body. Pumice is a mineral with abundant reserves and low prices, and its prospect of heavy metal adsorbent is very broad. In this work, we modified pumice with basic magnesium carbonate nanosheets by a convenient hydrothermal synthesis. The adsorption capacity of heavy metals is greatly improved. The effects of different pH and adsorption dosages are investigated. All the optimum pH values for Cu2+, Pb2+, and Cd2+ are 5. The adsorption of three kinds of ions conforms to the quasi-second-order adsorption kinetics model. The theoretical adsorption capacities of Cu2+, Pb2+, and Cd2+, which are calculated by the Langmuir model, are 235.29 mg/L, 595.24 mg/L, and 370.34 mg/L, respectively. The adsorption of Cu2+ and Cd2+ fit the Langmuir model better. The Freundlich model is fitted well with the adsorption of Pb2+. In the experiment simulating real wastewater, the adsorption capacity of heavy metals is not affected. It also shows good reusability in three regeneration cycles. And Mg5(CO3)4(OH)2·4H2O@pumice adsorption column showed the good removal efficiency of three heavy metals at different concentrations and different spatial velocities in the column experiment. Thus, it is believed that the Mg5(CO3)4(OH)2·4H2O@pumice is a promising adsorbent for the efficient removal of heavy metals.

2D materials towards energy conversion processes in nanofluidics

Hierarchically assembled 2D material membranes are extremely promising platforms for energy conversion processes in nanofluidics. In this perspective, we discuss recent advances in the production of smart 2D material membranes that come close to mimicking biological energy conversion processes and how these efforts translate into the design of water purification systems, artificial photosynthesis, and solar energy conversion devices. As we depict here, 2D material membranes synergistically modulate the intrinsic active sites (nanopores), electron transport, mass transfer, and mechanical and chemical stability aiming at cost-effective and highly efficient smart membranes.

Metal ferrites-based nanocomposites and nanohybrids for photocatalytic water treatment and electrocatalytic water splitting

Photocatalytic degradation is one of the most promising technologies available for removing a variety of synthetic and organic pollutants from the environmental matrices because of its high catalytic activity, reduced energy consumption, and low total cost. Due to its acceptable bandgap, broad light-harvesting efficiency, significant renewability, and stability, Fe₂O₃ has emerged as a fascinating material for the degradation of organic contaminants as well as numerous dyes. This study thoroughly reviewed the efficiency of Fe₂O₃-based nanocomposite and nanomaterials for water remediation. Iron oxide structure and various synthetic methods are briefly discussed. Additionally, the electrocatalytic application of Fe₂O₃-based nanocomposites, including oxygen evolution reaction, oxygen reduction reaction, hydrogen evolution reaction, and overall water splitting efficiency, was also highlighted to illustrate the great promise of these composites. Finally, the ongoing issues and future prospects are directed to fully reveal the standards of Fe₂O₃-based catalysts. This review is intended to disseminate knowledge for further research on the possible applications of Fe₂O₃ as a photocatalyst and electrocatalyst.

Recent trends and challenges with the synthesis of membranes: Industrial opportunities towards environmental remediation

The industrial and agricultural revolution has posed a serious and potential threat to environment. The industrial and agricultural pollutants are directly released into the environment. This issue has clinched the scientists to work on different materials in order to decontaminate the environment. Among all other techniques, the membrane filtration technology has fascinated researchers to overcome the pollution by its promising features. This review elaborated various membrane synthesis approaches along with their mechanism of filtration, their applications towards environmental remediation such as removal of heavy metals, degradation of dyes, pharma waste, organic pollutants, as well as gas sensing applications. The membrane synthesis using different sort of materials in which inorganic, carbon materials, polymers and metal organic framework (MOFs) are highlighted. These materials have been involved in synthesis of membrane to make it more cost effective and productive to remove such hazardous materials from wastewater. Based on the reported literature, it has been found that inorganic and polymer membranes are facing issues of brittleness and swelling prior to the industrial scale applications related to the high temperature and pressure which needs to be addressed to enhance the permeation performance.

Porphyrin-Based Conjugated Microporous Polymers for Highly Efficient Adsorption of Metal Ions

The capture and elimination of anions and cations from water have attracted a great deal of attention and are quite vital for clean production and environmental remediation. In this work, we present the synthesis of four porphyrin (Por)-based conjugated microporous polymers (CMPs, namely, Por-CMP-1-4), which were produced through a Sonogashira-Hagihara linked response using porphyrin and acetylene aromatic compounds as building blocks and used as absorbents to eliminate metal ions from water. The as-synthesized Por-CMP-1-4 exhibit an amorphous porous structure and outstanding caloric and physicochemical properties. Taking advantage of their larger specific surface areas, i.e., 541.47, 614.58, 382.38, and 677.90 m² g^-1 for Por-CMP-1-4, respectively, and their chelating active site that originated from the porphyrin ring, Por-CMP-1-4 show better Zn²⁺, Cu²⁺, and Pb²⁺ adsorption ability. Among them, Por-CMP-3 has the greatest adsorbability of 640 mg g^-1 for Zn²⁺, with an adsorption efficiency of 80%, whereas its adsorption capacities for Cu²⁺ and Pb²⁺ ions were both 334 mg g^-1, with an adsorption efficiency of 42% for Cu²⁺ and Pb²⁺. Employing Por-CMP-3 as a representative example, its adsorption kinetics has been systematically investigated. The adsorption behavior of Por-CMP-3 with respect to the Zn²⁺ ion is shown to exhibit pseudo-first-order kinetics and Langmuir isotherm modes. Meanwhile, the adsorption mechanism is discussed in detail, and it was thought it might be chelation, in which the nitrogen atoms with a single pair of electrons on the porphyrin ring interacted with metal ions to form stable chelation coordination bonds, thus removing metal ions selectively and effectively. Furthermore, Por-CMP-3 exhibited good reusability, retaining 60% of its Zn²⁺ removal rate after four continuous adsorptions.

Multifunctional hybrid membranes for photocatalytic and adsorptive removal of water contaminants of emerging concern

This work focuses on the combination of multifunctional photocatalytic and adsorbent materials in a unique polymeric membrane. For this purpose, Au/TiO₂ and Y₂(CO₃)₃ nanoparticles were immobilised onto a poly (vinylidene fluoride-hexafluoropropylene), (PVDF-HFP) membrane, and the physical-chemical characterisation of these materials was performed, as well as pollutant removal efficiency. An efficient TiO₂ functionalisation with gold nanoparticles was achieved, endowing these particles with the capability to absorb visible radiation absorption. A favourable porous structure was obtained for the membranes, with an average pore size of 4 μm, and the nanoparticles immobilisation did not alter the chemical properties of the polymeric membrane. The produced hybrid materials, including both the Au/TiO₂ and Y₂(CO₃)₃ nanoparticles, presented an efficiency of 57% in the degradation of norfloxacin (5 mg/L) under ultraviolet radiation for 120 min, 80% under visible radiation for 300 min, and 58% in arsenic adsorption for 240 min. These membranes represent a new multifunctional platform for removing several pollutants, which may allow their incorporation in more efficient and less energy-consuming water treatment processes favouring its application, even in low energy resources countries.

Modified Activated Carbon for Copper Ion Removal from Aqueous Solution

Because of increasing environmental awareness, it is becoming more important to remove harmful elements from water solutions. This study used activated carbon (AC) derived from waste wood-based panels as the base material, oxidized with nitric acid (OAC), and grafted with iminodiacetic acid (IDA-OAC) to improve the adsorption capacity and affinity for metals. The characterization of AC, OAC, and IDA-OAC was conducted via FTIR, SEM, N2 adsorption and desorption analysis, elemental analysis, Boehm titration, and point of zero charge (PZC). The instrument studies proved the modified increasing of the functional groups of the adsorbents. Moreover, batch and column experiments were conducted to evaluate the ability of the three adsorbents to remove copper ions from aqueous solution. In batch sorption, IDA-OAC had the highest adsorption capacity (84.51 mg/g) compared to OAC (54.74 mg/g) and AC (24.86 mg/g) at pH 5. The breakthrough point (Ct/Ci = 0.05) of copper ions for IDA-OAC occurred much later than AC in the column experiment (AC = 19 BV, IDA-OAC = 52 BV). The Langmuir isotherm and pseudo-second-model kinetics modeling could better fit with the data obtained from the batch sorption of AC, OAC, and IDA-OAC. The significant capacity and reusability of IDA-OAC displayed high applicability for water treatment.

Adsorption and Reduction of Aqueous Cr by FeS-Modified Fe-Al Layered Double Hydroxide

To remedy the widespread chromium (Cr) pollution in the environment, this study mainly used the ultrasonic-assisted co-precipitation and precipitation methods to prepare FeS-modified Fe-Al-layered double hydroxide (FeS/LDH) composite material. The experimental results showed that FeS/LDH has higher removal efficiency of Cr in aqueous solution and stronger anti-interference ability than unmodified LDH. Under the same reaction conditions, the removal efficiency of total Cr(Cr(T)) using LDH was 34.85%, and the removal efficiency of Cr(VI) was 46.76%. For FeS/LDH, the removal efficiency of Cr(T) and Cr(VI) reached 99.57% and 100%, respectively. The restoration of Cr(T) and Cr(VI) by FeS/LDH satisfied the Langmuir adsorption isotherm. The maximum adsorption capacity of Cr(T) and Cr(VI) achieved 102.9 mg/g and 147.7 mg/g. The efficient removal of Cr by FeS/LDH was mainly based on the triple synergistic effect of anion exchange between Cr(VI) and interlayer anions, redox of Cr(VI) with Fe2+ and S2−, and co-precipitation of Fe3+ and Cr3+.