Comparative investigation on synthesis, morphological tailoring and photocatalytic activities of Bi2O2CO3 nanostructures

Bismuth oxybromide nanosheets as an efficient photocatalyst for dye degradation

The contamination of water resources by organic pollutants presents significant environmental and health challenges. Therefore, it is urgent to develop highly efficient and green approach for treating organic water pollutants. Bismuth oxybromide (BiOBr) has gained attention due to its high photoactivity. In this work, we report a modification to improve its photocatalytic activity. BiOBr were prepared using a capping agent, benzene-1,3,5-tricarboxylic acid, to tune the morphology of the compound. The resulting BiOBr shows nanosheet morphology, which provides a high surface-to-volume ratio and a larger conduction band compared to bulk BiOBr. As a result, the BiOBr nanosheets show the highest efficiency for photodegradation of Rhodamine B, compared to benchmark TiO2 and bulk BiOBr catalysts.

Modulating Surface-Adsorbed Oxygen Species of Bismuth Silicate by a Solid Solution Strategy for Efficient Adsorption and Photocatalytic Activity

Bismuth silicate photocatalysts suffer from insufficient photocatalytic activity due to an insufficient number of surface active sites and low carrier separation and transport efficiency, which can be solved by defect modulation. Herein, Bi12SiO20/Bi2O2SiO3-BiOClxBr1-x (BSOCB) photocatalysts with a high concentration of surface-adsorbed oxygen species (SAOS) are synthesized by introducing a BiOClxBr1-x solid solution to modify nonhomogeneous BSO via an ion exchange strategy. The introduction of a solid solution enables the generation of dispersed nanoflowers and the regulation of SAOS due to the fact that anion-cation copolymerization guides the crystal growth, and the defects generated by the lattice distortion modulate the concentration of SAOS on the catalysts during the solid solution process. The obtained typical BSOCB photocatalyst possesses both high adsorption and photocatalytic properties, and the results show that it not only can almost completely degrade the traditional pollutant RhB within 20 min but also strongly degrades antibiotics, such as CIP (light for 150 min, 96%), NFX (light for 150 min, 87%), and TC (light for 150 min, 77%). This work provides a new approach for obtaining bismuth-based photocatalysts with controllable morphology and a large number of surface active sites and provides a theoretical and experimental basis for expanding the application scenarios of photocatalysts.

One-pot synthesis of interfacially bonded Bi4O5Br2/Bi2S3 Z-scheme heterostructures with boosted photocatalysis towards dodecylbenzenesulfonate and real hotel laundry wastewater

The ubiquitous contamination of surfactants in wastewater has raised global concerns. Photocatalysis is deemed as a promising yet challenging approach for the decomposition of surfactant residues. Herein, a novel Z-scheme heterojunction of Bi4O5Br2/Bi2S3 with covalent S-O bonds was prepared via a facile one-pot hydrothermal and subsequent annealing process. The prepared optimal Bi4O5Br2/Bi2S3 composite exhibited remarkable photo-degradation activity towards the sodium dodecylbenzene sulfonate (SDBS). The Z-scheme reaction mechanism was proposed and validated by meticulous analysis of quenching tests, ESR spectroscopy and DFT calculations. Furthermore, the presence of chemical S-O linkages between Bi4O5Br2 and Bi2S3 was identified via FT-IR and XPS analyses, which served as a distinct bridge to modify the Z-scheme route for carrier transport. The Z-scheme heterostructure, in conjunction with chemical S-O bonds, synergistically enhanced the separation rate of electron-hole pairs and thus greatly boosted the photocatalytic activity. Additionally, the possible degradation pathways of SDBS were proposed by using HR-MS technology. Moreover, real hotel laundry wastewater could be efficiently disposed by the photocatalysis of the Bi4O5Br2/Bi2S3 with a decrease in the COD value from 428 to 74 mg/L, indicating that the fabricated Z-scheme heterojunction hold great promise for effectively removing refractory surfactant contaminants from aquatic environment.

Experimental and theoretical revealing of piezo-photocatalyst Bi2O2CO3 for degradation of ciprofloxacin in water

In this report, we have attempted to experimentally and theoretically reveal a new piezo-photocatalyst Bi2O2CO3 for efficient removal of ciprofloxacin (CIP) from water. Bi2O2CO3 nanoplates were synthesized to evaluate their photocatalytic (irradiation source: simulated-sunlight), piezocatalytic (irradiation source: ultrasonic) and piezo-photocatalytic (irradiation source: simulated-sunlight and ultrasonic) performances for CIP elimination. Under the condition CCIP = 10 mg/L and Ccatalyst = 1 g/L, the piezo-photodegradation rate constant is obtained as kapp = 0.07811 min-1, which surpasses that of photocatalysis (kapp = 0.04686 min-1) and piezocatalysis (kapp = 0.01233 min-1); this phenomenon manifests an obvious piezo-enhanced photocatalytic behavior in terms of the "1 + 1 > 2" principle. The ultrasonic-induced piezoelectric behavior in Bi2O2CO3 nanoplates and involved piezo-photocatalytic mechanism were theoretically elucidated by density functional theory (DFT) and finite-element method (FEM) studies. Additionally, the effects of various factors on the CIP degradation, decomposition mechanism of CIP and toxicity of the decomposition intermediates were also analyzed.

Construction of Cu7 S4 @CuCo2 O4 Yolk-Shell Microspheres Composite and Elucidation of Its Enhanced Photocatalytic Activity, Mechanism, and Pathway for Carbamazepine Degradation

Water pollution caused by the massive use of medicines has caused significant environmental problems. This work first reports the synthesis and characterization of the Cu₇ S₄ /CuCo₂ O₄ (CS/CCO) yolk-shell microspheres via hydrothermal and annealing methods, and then investigates their photocatalytic performance in removing organic water pollutants. The 10-CS/CCO composite with yolk-shell microspheres exhibits the highest photodegradation rate of carbamazepine (CBZ), reaching 96.3% within 2 h. The 10-CS/CCO also demonstrates more than two times higher photodegradation rates than the pure (Cu₇ S₄ ) CS and (CuCo₂ O₄ ) CCO. This outstanding photocatalytic performance can be attributed to the unique yolk-shell structure and the Z-scheme charge transfer pathway, reducing multiple reflections of the acting light. These factors enhance the light absorption efficiency and efficiently transfer photoexcited charge carriers. In-depth, photocatalytic degradation pathways of CBZ are systematically evaluated via the identification of degradation intermediates with Fukui index calculation. The insights gained from this work can serve as a guideline for developing low-cost and efficient Z-scheme photocatalyst composites with the yolk-shell structure.

Interfacial S-O bonds specifically boost Z-scheme charge separation in a CuInS2/In2O3 heterojunction for efficient photocatalytic activity

Reducing the recombination rate of photoexcited electron-hole pairs is always a great challenging work for the photocatalytic technique. In response to this issue, herein, a novel Z-scheme CuInS2/In2O3 with interfacial S-O linkages was synthesized by a hydrothermal and subsequently annealing method. The Fourier transform infrared (FT-IR) and X-ray photoelectron spectrometer (XPS) measurements confirmed the formation of covalent S-O bonds between CuInS2 and In2O3. The quenching and electron spin resonance (ESR) tests revealed the Z-scheme transfer route of photogenerated carriers over the CuInS2/In2O3 heterojunctions, which was further verified theoretically via density functional theory (DFT) calculations. As expected, the CuInS2/In2O3 heterojunctions showed significantly boosted photocatalytic activities for lomefloxacin degradation and Cr(vi) reduction under visible light illumination compared with the bare materials. Accordingly, a synergistic photocatalytic mechanism of Z-scheme heterostructures and interfacial S-O bonding was proposed, in which the S-O linkage could act as a specific bridge to modify the Z-scheme manner for accelerating the interfacial charge transmission. Furthermore, the CuInS2/In2O3 heterojunction also exhibited excellent performance perceived in the stability and reusability tests. This work provides a new approach for designing and fabricating novel Z-scheme heterostructures with a high-efficiency charge transfer route.

Construction of Z-Scheme Ag2MoO4/ZnWO4 Heterojunctions for Photocatalytically Removing Pollutants

Facilitation of the photocarrier separation is a crucial strategy for developing highly efficient photocatalysts in eliminating environmental pollutants. Herein we have developed a new kind of Ag2MoO4/ZnWO4 (AMO/ZWO) composite photocatalysts with a Z-scheme mechanism by anchoring AMO nanoparticles onto ZWO nanorods. Multiple characterization methodologies and density functional theory (DFT) calculations were employed to study the performances of the AMO/ZWO heterojunctions as well as the underlying photocatalytic mechanism. Simulated-sunlight-driven photodegradation experiments for removing methylene blue (MB) demonstrates that the 8%AMO/ZWO heterojunction can photocatalytically remove 99.8% of MB within 60 min, and the reaction rate constant is obtained as 0.10199 min-1, which is enhanced by 6.8 (or 4.9) times when compared with that of pure ZWO (or AMO). On the base of the experimental results and DFT calculations, the enhanced photocatalytic mechanism of the AMO/ZWO heterojunctions was revealed to be the efficient separation of photocarriers via a Z-scheme transfer process. In addition, photodegradion of various organic pollutants over 8%AMO/ZWO was further compared and aimed at incorporating it into industrial application in pollutant removal.

Effect of H2O2 @CuONPs in the UV Light-Induced Removal of Organic Pollutant Congo Red Dye: Investigation into Mechanism with Additional Biomedical Study

Hazardous dyes in industrial wastewater are an internationally recognized issue for community health. Nanoparticles synthesized through green protocols are a fascinating research field with numerous applications. The current study mainly aimed to investigate the degradation of Congo red (CR) dye under UV light in the presence of H2O2 and the photocatalytic activity of copper oxide nanoparticles (CuONPs). For CuONP formation, Citrus maxima extract contains a high number of phytochemical constituents. The size of CuONPs ranges between 25 and 90 nm. The photocatalytic activity of CuONPs with the addition of H2O2 was observed and analyzed under UV light to eliminate CR dye. The UV light caused the decomposition of H2O2, which produced ·OH radicals. The results revealed a significant increment in dye degradation during the presence of H2O2. The effect of concentration on the degradation of the CR dye was also studied. The degradation pathway of organic pollutants was reputable from the hydroxy radical medicated degradation of CR. Advanced Oxidation Treatment depends on the in situ production of reactive ·OH species and is presented as the most effective procedure for decontamination. The biological activity of CuONPs was evaluated against Escherichia coli Bacillus subtillis, Staphylococcus aureus, Shigella flexenari, Acinetobacter Klebsiella pneumonia, Salmonella typhi and Micrococcus luteus. The newly synthesised nanomaterials showed strong inhibition activity against Escherichia coli (45%), Bacillus subtilis (42%) and Acinetobacter species (25%). The activity of CuONPs was also investigated against different fungus species such as: Aspergillus flavus, A. niger, Candida glabrata, T. longifusus, M. Canis, C. glabrata and showed a good inhibition zone against Candida glabrata 75%, Aspergillus flavus 68%, T. longifusus 60%. The materials showed good activity against C. glaberata, A. flavus and T. longifusus. Furthermore, CuONPs were tested for antioxidant properties using 2, 2 diphenyl-1-picrylhydrazyl) (DPPH).

Construction of a Z-scheme Ag2MoO4/BiOBr heterojunction for photocatalytically removing organic pollutants

How to facilitate photogenerated-carrier separation is an important step in developing excellent semiconductor photocatalysts for environmental pollutant removal. Herein, Ag₂MoO₄ (AMO) nanoparticles were assembled onto the surface of BiOBr (BOB) nanosheets to construct a highly efficient Z-scheme AMO/BOB heterojunction photocatalyst. Several analytical techniques were used to elucidate the characteristics and photocatalytic mechanism of the AMO/BOB heterojunction. Photodegradation experiments for removing methylene blue under simulated-sunlight irradiation reveal that a 20%AMO/BOB heterojunction exhibits excellent photodegradation activity with η(30 min) = 93.8% and k_app = 0.08638 min^-1, which were greater by 4.5 and 5.6 times in comparison with that of pure BOB and AMO, respectively. Based on the experimental and density functional theory (DFT) calculation results, it is proposed that the Z-scheme carrier transfer/separation mechanism dominates the enhanced photodegradation performance of the composite photocatalysts. Additionally, the potential application of AMO/BOB photocatalysts in degrading various organic pollutants (including organic dyes, antibiotics and other serious organic pollutants) was also investigated.

Synthesis of Co3O4 Nanoparticles-Decorated Bi12O17Cl2 Hierarchical Microspheres for Enhanced Photocatalytic Degradation of RhB and BPA

Three-dimensional (3D) hierarchical microspheres of Bi₁₂O₁₇Cl₂ (BOC) were prepared via a facile solvothermal method using a binary solvent for the photocatalytic degradation of Rhodamine-B (RhB) and Bisphenol-A (BPA). Co₃O₄ nanoparticles (NPs)-decorated BOC (Co₃O₄/BOC) heterostructures were synthesized to further enhance their photocatalytic performance. The microstructural, morphological, and compositional characterization showed that the BOC microspheres are composed of thin (~20 nm thick) nanosheets with a 3D hierarchical morphology and a high surface area. Compared to the pure BOC photocatalyst, the 20-Co₃O₄/BOC heterostructure showed enhanced degradation efficiency of RhB (97.4%) and BPA (88.4%). The radical trapping experiments confirmed that superoxide (^•O₂^-) radicals played a primary role in the photocatalytic degradation of RhB and BPA. The enhanced photocatalytic performances of the hierarchical Co₃O₄/BOC heterostructure are attributable to the synergetic effects of the highly specific surface area, the extension of light absorption to the more visible light region, and the suppression of photoexcited electron-hole recombination. Our developed nanocomposites are beneficial for the construction of other bismuth-based compounds and their heterostructure for use in high-performance photocatalytic applications.

Self-Assembly 2D Ti3C2/g-C3N4 MXene Heterojunction for Highly Efficient Photocatalytic Degradation of Tetracycline in Visible Wavelength Range

An ultrathin 2D Ti₃C₂/g-C₃N₄ MXene (2D-TC/CN) heterojunction was synthesized, using a facile self-assembly method; the perfect microscopic-morphology and the lattice structure presented in the sample with a 2 wt% content of Ti₃C₂ were observed by the field-emission scanning electron microscopy (SEM) and transmission electron microscope (TEM). The optimized sample (2-TC/CN) exhibited excellent performance in degrading the tetracycline (TC), and the degradation rate reached 93.93% in the conditions of 20 mg/L, 50 mL of tetracycline within 60 min. Except for the increased specific-surface area, investigated by UV-vis diffuse reflectance spectra (UV-vis DRS) and X-ray photoelectron microscopy (XPS) valence spectra, the significantly enhanced photocatalytic activity of the 2-TC/CN could also be ascribed to the formation of Ti-N bonds between Ti₃C₂ and g-C₃N₄ nanosheets, which reduced the width of the band gap through adjusting the position of the valence band, thus resulting in the broadened light-absorption. Furthermore, the facilitated electron transmission was also proved by time-resolved photoluminescence (TRPL) and electrochemical impedance spectroscopy (EIS), which is effective in improving the quantum efficiency of photo-generated electrons. In addition, the resulting radical-capture experiment suggested that superoxide radicals have the greatest influence on photodegradation performance, with the photodegradation rate of TC reducing from 93.16% to 32.08% after the capture of superoxide radicals, which can be attributed to the production of superoxide radicals only, by the 2-TC/CN composites with a high conduction-band value (-0.62 eV). These facilely designed 2D Ti₃C₂/g-C₃N₄ composites possess great application potential for the photodegradation of tetracycline and other antibiotics.

Tunable high-sensitivity sensing detector based on Bulk Dirac semimetal

This paper proposes a tunable sensing detector based on Bulk Dirac semimetals (BDS). The bottom-middle-top structure of the detector is a metal-dielectric-Dirac semimetal. The designed detector is simulated in the frequency domain by the finite element method (FEM). And the simulation results indicate that the detector achieves three perfect absorption peaks with absorptivity greater than 99.8% in the range of 2.4-5.2 THz. We analyze the cause of the absorption peak by using random phase approximation theory. The device exhibits good angular insensitivity in different incident angle ranges, and the three absorption peaks can reach 90% absorption rate when the incident angle is in the ranges of 0-60°. And when adjusting the Fermi level of BDS in the ranges of 0.1-0.5 eV, our detector can realize the frequency regulation of the ultra-wide range of 3.90-4.56 THz and realize multi-frequency controllable sensing while maintain the absorption efficiency above 96%. The detector has maximum sensitivity S of 238.0 GHz per RIU when the external environment of the refractive index changes from 1.0 to 1.8, and the maximum detection accuracy is 6.5. The device has broad development prospects in the field of space detection and high-sensitivity biosensing detection.

Influence of Synthesis Conditions on Physicochemical and Photocatalytic Properties of Ag Containing Nanomaterials

Silver (Ag) containing nanomaterials were successfully prepared by varying synthesis conditions to understand the influence of preparation conditions on the physicochemical and photocatalytic properties of these materials. Different analytical techniques such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), Diffuse reflectance UV-vis spectra (DR UV-vis), X-ray photoelectron spectroscopy (XPS) measurements, and N2-physisorption were used to investigate the physicochemical properties of synthesized Ag containing nanomaterials. The samples (Ag-1 and Ag-2) prepared using AgNO3, NaHCO3, and polyvinylpyrrolidone (PVP) template exhibited pure Ag metal nanorods and nanoparticles; the morphology of Ag metal is influenced by the hydrothermal treatment. The Ag-3 sample prepared without PVP template and calcined at 250 °C showed the presence of a pure Ag2O phase. However, the same sample dried at 50 °C (Ag-4) showed the presence of a pure Ag2CO3 phase. Interestingly, subjecting the sample to hydrothermal treatment (Ag-5) has not resulted in any change in crystal structure, but particle size was increased. All the synthesized Ag containing nanomaterials were used as photocatalysts for p-nitrophenol (p-NP) degradation under visible light irradiation. The Ag-4 sample (pure Ag2CO3 with small crystallite size) exhibited high photocatalytic activity (86% efficiency at pH 10, p-NP concentration of 16 mg L−1, 120 min and catalyst mass of 100 mg) compared to the other synthesized Ag containing nanomaterials. The high photocatalytic activity of the Ag-4 sample is possibly due to the presence of a pure Ag2CO3 crystal structure with nanorod morphology with a low band gap energy of 1.96 eV and relative high surface area.

Highly sensitive sensing of a magnetic field and temperature based on two open ring channels SPR-PCF

A surface plasmon resonance (SPR) sensor comprising photonic crystal fiber (PCF) is designed for magnetic field and temperature dual-parameter sensing. In order to make the SPR detection of magnetic field and temperature effectively, the two open ring channels of the proposed sensor are coated with gold and silver layers and filled with magnetic fluid (MF) and Polydimethylsiloxane (PDMS), respectively. The sensor is analyzed by the finite element method and its mode characteristics, structure parameters and sensing performance are investigated. The analysis reveals when the magnetic field is a range of 40-310 Oe and the temperature is a range of 0-60 °C, the maximum magnetic field sensitivity is 308.3 pm/Oe and temperature sensitivity is 6520 pm/°C. Furthermore, temperature and magnetic field do not crosstalk with each other's SPR peak. Its refractive index sensing performance is also investigated, the maximum sensitivity and FOM of the left channel sensing are 16820 nm/RIU and 1605 RIU^-1, that of the right channel sensing are 13320 nm/RIU and 2277 RIU^-1. Because of its high sensitivity and special sensing performance, the proposed sensor will have potential application in solving the problems of cross-sensitivity and demodulation due to nonlinear changes in sensitivity of dual-parameter sensing.

Novel scheme towards interfacial charge transfer between ZnIn2S4 and BiOBr for efficient photocatalytic removal of organics and chromium (VI) from water

Construction of Z-scheme heterostructure is an effective strategy to enhance the charge carriers' separation. However, successfully achieving this on the defect heterojunction to improve the photocatalytic activity remains challenging. This work successfully obtained sulfur vacancy in the ZnIn₂S₄/BiOBr (SZIS/BOB) heterojunction composites with S-O covalent bonding using a hydrothermal method. As a result, they exhibited superior photocatalytic and stability performance. The optimized SZIS/BOB-10 exhibited excellent rhodamine B degradation (95.2%) and chromium (VI) reduction (97.8%) within 100 min under visible light. The enhanced composites with S-vacancies, S-O bond, and internal electric field induced the Z-scheme charge transfer mechanism. We had verified this mechanism based on the surface photovoltage spectra, electron spin response spectra, and density functional theory calculations. This work not only provides valuable insights into designing photocatalysts with a direct Z scheme heterostructure but also delineates a promising strategy for developing efficient photocatalysts to degrade organic pollutants.

An eco-friendly and sustainable support of agave-fibers functionalized with graphene/TiO2:SnO2 for the photocatalytic degradation of the 2,4-D herbicide from the drinking water

In this research, we evaluated the photocatalytic performance of biodegradable composites for the removal of the 2,4-Dichlorophenoxyacetic acid (2,4-D) herbicide. The composite was composed by agave fibers (AgF), graphene-microplates (GM) and titanium dioxide TiO₂/SnO₂ (TSn) nanoparticles (NPs) and was named TSn + AgF/GM. Both, the TSn NPs and the GM were deposited on the AgF using the Dip-coating method. According to the analysis by X-Ray Diffraction (XRD), the crystalline phase for the TiO₂ and SnO₂ was anatase and tetragonal-rutile, respectively. The Scanning Electron Microscopy (SEM) images demonstrated that the AgF were completely saturated by the GM (which had average dimensions of 15 μm × 22 μm) and by conglomerations of TSn NPs with average size of 642 nm. The TSn NPs and the TSn + AgF/GM composite were evaluated for the photocatalytic degradation of the 2,4-D herbicide under ultraviolet-visible (UV-Vis) light and found a maximum degradation of 98.4 and 93.7% (after 4 h) for the TSn NPs and the TSn + AgF/GM composite, respectively. Reuse cycles were also performed and the degradation percentage decreased by 13.1% and by 7.8% (after 3 cycles of reuse) when the TSn NPs and the TSn + AgF/GM composite are employed, respectively. Scavenger experiments were also carried out and found that the oxidizing agents are mainly produced in the order of: •OH>•O₂^- > h⁺; then, the main oxidizing agents generated during the photocatalytic reaction were the hydroxyl radicals. Thus, the photocatalytic system studied in this work for the degradation of 2,4-D could pave the way for the development of new eco-friendly/floatable photocatalysts, which can be applied in wastewater-treatment plants.

Two-channel photonic crystal fiber based on surface plasmon resonance for magnetic field and temperature dual-parameter sensing

In this paper, a dual-parameter sensor based on surface plasmon resonance (SPR)-photonic crystal fiber (PCF) is proposed, which can be applied in detecting the magnetic field and temperature. In this sensor, two elliptical channels are designed on both sides of the fiber core. The left channel (Ch 1) is coated with gold film and filled with magnetic fluid (MF) to achieve a response to the magnetic field and temperature using SPR. The right channel (Ch 2) is coated with gold film as well as Ta₂O₅ film to improve the SPR sensing performance. Finally, Ch 2 is filled with polydimethylsiloxane (PDMS) to achieve a response to the temperature. The mode characteristics, structural parameters and sensing performance are investigated by the finite element method. The results show that when the magnetic field is in the range of 50-130 Oe, the magnetic field sensitivities of Ch 1 and Ch 2 are 65 pm Oe^-1 and 0 pm Oe^-1, respectively. When the temperature is in the range of 17.5-27.5 °C, the temperature sensitivities of Ch 1 and Ch 2 are 520 pm °C^-1 and 2360 pm °C^-1, respectively. By establishing and demodulating a sensing matrix, the sensor can not only measure the temperature and magnetic field simultaneously but also solve the temperature cross-sensitivity problem. In addition, when the temperature exceeds a certain value, the proposed sensor is expected to achieve dual-parameter sensing without a matrix. The proposed dual-parameter SPR-PCF sensor has a unique structure and excellent sensing performance, which are important for the simultaneous sensing of multiple basic physical parameters.

Design of Ultra-Narrow Band Graphene Refractive Index Sensor

The paper proposes an ultra-narrow band graphene refractive index sensor, consisting of a patterned graphene layer on the top, a dielectric layer of SiO₂ in the middle, and a bottom Au layer. The absorption sensor achieves the absorption efficiency of 99.41% and 99.22% at 5.664 THz and 8.062 THz, with the absorption bandwidths 0.0171 THz and 0.0152 THz, respectively. Compared with noble metal absorbers, our graphene absorber can achieve tunability by adjusting the Fermi level and relaxation time of the graphene layer with the geometry of the absorber unchanged, which greatly saves the manufacturing cost. The results show that the sensor has the properties of polarization-independence and large-angle insensitivity due to the symmetric structure. In addition, the practical application of testing the content of hemoglobin biomolecules was conducted, the frequency of first resonance mode shows a shift of 0.017 THz, and the second resonance mode has a shift of 0.016 THz, demonstrating the good frequency sensitivity of our sensor. The S (sensitivities) of the sensor were calculated at 875 GHz/RIU and 775 GHz/RIU, and quality factors FOM (Figure of Merit) are 26.51 and 18.90, respectively; and the minimum limit of detection is 0.04. By comparing with previous similar sensors, our sensor has better sensing performance, which can be applied to photon detection in the terahertz band, biochemical sensing, and other fields.

High-Q refractive index sensors based on all-dielectric metasurfaces

Possessing fantastic abilities to freely manipulate electromagnetic waves on an ultrathin platform, metasurfaces have aroused intense interest in the academic circle. In this work, we present a high-sensitivity refractive index sensor excited by the guided mode of a two-dimensional periodic TiO2 dielectric grating structure. Numerical simulation results show that the optimized nanosensor can excite guided-mode resonance with an ultra-narrow linewidth of 0.19 nm. When the thickness of the biological layer is 20 nm, the sensitivity, Q factor, and FOM values of the nanosensor can reach 82.29 nm RIU-1, 3207.9, and 433.1, respectively. In addition, the device shows insensitivity to polarization and good tolerance to the angle of incident light. This demonstrates that the utilization of low-loss all-dielectric metasurfaces is an effective way to achieve ultra-sensitive biosensor detection.

Perfect Absorption of Fan-Shaped Graphene Absorbers with Good Adjustability in the Mid-Infrared

This paper presents a graphene metamaterial absorber based on impedance matching. A finite difference in time domain (FDTD) method is used to achieve a theoretically perfect absorption in the mid-infrared band. A basis is created for the multiband stable high absorption of graphene in the mid-infrared. The designed graphene absorber is composed of graphene, a dielectric layer, a gold plane, and a silicon substrate, separately. The incident source of mid-infrared can be utilized to stimulate multiband resonance absorption peaks from 2.55 to 4.15 μm. The simulation results show that the absorber has three perfect resonance peaks exceeding 99% at λ1 = 2.67 μm, λ2 = 2.87 μm, and λ3 = 3.68 μm, which achieve an absorption efficiency of 99.67%, 99.61%, and 99.40%, respectively. Furthermore, the absorber maintains an excellent performance with a wide incident angle range of 0°–45°, and it also keeps the insensitive characteristic to transverse electric wave (TE) and transverse magnetic wave (TM). The results above indicate that our perfect graphene absorber, with its tunability and wide adaptability, has many potential applications in the fields of biosensing, photodetection, and photocell.

Metamaterial Solar Absorber Based on Refractory Metal Titanium and Its Compound

Metamaterials refers to a class of artificial materials with special properties. Through its unique geometry and the small size of each unit, the material can acquire unique electromagnetic field properties that conventional materials do not have. Based on these factors, we put forward a kind of high absorption near-ultraviolet to near-infrared electromagnetic wave absorber of the solar energy. The surface structure of the designed absorber is composed of TiN-TiO2-Al2O3 with rectangles and disks, and the substrate is Ti-Al2O3-Ti layer. In the study band range (0.1–3.0 μm), the solar absorber’s average absorption is up to 96.32%, and the designed absorber absorbs more than 90% of the electromagnetic wave with a wavelength width of 2.577 μm (0.413–2.990 μm). Meanwhile, the designed solar absorber has good performance under different angles of oblique incident light. Ultra-wideband solar absorbers have great potential in light absorption related applicaitions because of their wide spectrum high absorption properites.

S-Scheme BiOCl/MoSe2 Heterostructure with Enhanced Photocatalytic Activity for Dyes and Antibiotics Degradation under Sunlight Irradiation

Semiconductor photocatalysis is considered to be a promising technique to completely eliminate the organic pollutants in wastewater. Recently, S-scheme heterojunction photocatalysts have received much attention due to their high solar efficiency, superior transfer efficiency of charge carriers, and strong redox ability. Herein, we fabricated an S-scheme heterostructure BiOCl/MoSe₂ by loading MoSe₂ nanosheets on the surface of BiOCl microcrystals, using a solvothermal method. The microstructures, light absorption, and photoelectrochemical performances of the samples were characterized by the means of SEM, TEM, XRD, transient photocurrents, electrochemical impedance, and photoluminescence (PL) spectra. The photocatalytic activities of BiOCl, MoSe₂, and the BiOCl/MoSe₂ samples with different MoSe₂ contents were evaluated by the degradation of methyl orange (MO) and antibiotic sulfadiazine (SD) under simulated sunlight irradiation. It was found that BiOCl/MoSe₂ displayed an evidently enhanced photocatalytic activity compared to single BiOCl and MoSe₂, and 30 wt.% was an optimal loading amount for obtaining the highest photocatalytic activity. On the basis of radical trapping experiments and energy level analyses, it was deduced that BiOCl/MoSe₂ follows an S-scheme charge transfer pathway and •O₂⁻, •OH, and h⁺ all take part in the degradation of organic pollutants.

Grating Structure Broadband Absorber Based on Gallium Arsenide and Titanium

We designed a broadband absorber based on a multilayer grating structure composed of gallium arsenide and titanium. The basic unit is a grating structure stacked on top of a semiconductor of gallium arsenide and titanium metal. We used the finite difference time domain method to simulate the designed model and found that the absorber absorption efficiency exceeded 90% in the range from 736 nm to 3171 nm. The absorption efficiency near perfect absorption at 867 nm was 99.69%. The structure had good angle insensitivity, and could maintain good absorption under both the TE mode and TM mode polarized light when the incident angle of the light source changed from 0° to 50°. This kind of metamaterial grating perfect absorber is expected to be widely used in optical fields such as infrared detection, optical sensing, and thermal electronics.