Influence of the oil globule fraction on the release rate profiles from multiple W/O/W emulsions

Multiple Pickering emulsions stabilized by the same particles with different extent of hydrophobization in situ

Multiple emulsions are widely used in pharmaceuticals, foods, and cosmetics. However, those stabilized by surfactants with different HLB values are generally unstable due to the diffusion of the surfactants between inner and outer interfaces. Here, we report that multiple W/O/W emulsions can be prepared by using the same particles in combination with a surfactant of different concentrations. The less surface-active raw CaCO₃ nanoparticles can be hydrophobized to surface-active in situ by adsorption of the anionic surfactant SDS, and the wettability of the particles can be controlled to be suitable for stabilizing both O/W and W/O Pickering emulsions by adjusting the surfactant concentration. With toluene as oil phase, the CaCO₃ particles at 1.0 wt% tend to stabilize a W/O emulsion in the presence of 3 mm SDS in an aqueous solution, which can then be further dispersed in an aqueous phase with 1.0 wt% CaCO₃ and SDS below 1 mm to form a W/O/W multiple emulsion. The effects of the ratio of W/O emulsion to the outer water phase and the preparation methods on stabilization of multiple emulsions were examined. With a ratio smaller than 3:1 and by gentle magnetic stirring, the multiple emulsions obtained can stay stable for at least a month without coalescence. This simple method not only ensures stabilization of multiple emulsions but also avoids complicated synthesis of colloid particles with different wettability.

Effect of Gum Acacia on the Intestinal Bioavailability of n-3 Polyunsaturated Fatty Acids in Rats

Lipid emulsification is a technique that is being explored for improving the bioavailability of omega 3 (n-3) long chain (LC) fatty acid (FA). The nature of the emulsifiers can differently impact the lipid bioavailability via a modification of the lipolysis step. Among natural emulsifiers, gum acacia (GA), an indigestible polysaccharide, provides protective encapsulation of n-3 by forming a specifically crown-like shape around lipid drops, which could also impact the digestion step. Despite the interest in lipolysis rate, the impact of GA on lipid bioavailability has never been explored in a complete physiological context. Thus, we followed in a kinetics study the n-3 bioavailability in rat lymph, orally administered DHA-rich oil, formulated based on GA compared to the bulk phase form of the oil. The AUC values were significantly improved by +121% for total TG and by 321% for n-3 PUFA, specifically for EPA (+244%) and for DHA (+345%). Benefits of GA have also been related to the transport of FA in lymph, which was 2 h earlier (Tmax = 4 h), compared to the Tmax (6 h) obtained with the bulk phase oil. All the data showed that GA is one of the most favorable candidates of natural emulsifiers to improve n-3 bioavailability and their rate of absorption for health targets.

Fat crystals: A tool to inhibit molecular transport in W/O/W double emulsions

Water-in-oil-in-water (W/O/W) double emulsions are a promising technology for encapsulation applications of water soluble compounds with respect to functional food systems. Yet molecular transport through the oil phase is a well-known problem for liquid oil-based double emulsions. The influence of network crystallization in the oil phase of W/O/W globules was evaluated by NMR and laser light scattering experiments on both a liquid oil-based double emulsion and a solid fat-based double emulsion. Water transport was assessed by low-resolution NMR diffusometry and by an osmotically induced swelling or shrinking experiment, whereas manganese ion permeation was followed by means of T₂ -relaxometry. The solid fat-based W/O/W globules contained a crystal network with about 80% solid fat. This W/O/W emulsion showed a reduced molecular water exchange and a slower manganese ion influx in the considered time frame, whereas its globule size remained stable under the applied osmotic gradients. The reduced permeability of the oil phase is assumed to be caused by the increased tortuosity of the diffusive path imposed by the crystal network. This solid network also provided mechanical strength to the W/O/W globules to counteract the applied osmotic forces.

Determination of Formulation Conditions Allowing Double Emulsions Stabilized by PGPR and Sodium Caseinate to Be Used as Capsules

Water-in-oil-in-water (W₁/O/W₂) double emulsions stabilized by polyglycerol polyricinoleate (PGPR), a lipophilic food grade small polymer, and sodium caseinate, a hydrophilic milk protein, were developed to encapsulate vitamin B12, a model hydrophilic substance easy to titrate. Using rheology, sensitive to drop size evolution and water fluxes, static light scattering, and microscopy both giving the evolution of drops' size and vitamin B12 titration assessing the encapsulation, we were able to detect independently the double emulsion drop size, the encapsulation loss, and the flux of water as a function of time. By differentiating the PGPR required to cover the W₁-droplets' surface from PGPR in excess in the oil phase, we built a PGPR-inner droplet volume fraction diagram highlighting the domains where the double emulsion is stable toward encapsulation and/or water fluxes. We demonstrated the key role played by nonadsorbed PGPR concentration in the intermediate sunflower oil phase on the emulsion stability while, surprisingly, the inner droplet volume fraction had no effect on the emulsion stability. At low PGPR concentration, a release of vitamin B12 was observed and the leakage mechanism of coalescence between droplets and oil-water interface of the oily drops (also called globules hereafter), was identified using confocal microscopy. For high enough PGPR content, the emulsions were stable and may therefore serve as efficient capsules without need of an additional gelling, thickening, complexion or interface rigidifying agent. We generalized these results with the encapsulation of an insecticide: Cydia pomonella granulovirus used in organic arboriculture.

In vitro digestion behavior of water-in-oil-in-water emulsions with gelled oil-water inner phases

Double emulsions may be able to protect and release in a controlled manner bioactive compounds during digestion of food matrices. It was hypothesized that the physical state and solid content in the inner phases of water-in-oil-in-water (W₁/O/W₂) emulsions may affect the overall stability and the release behavior of bioactives during in vitro digestion. Therefore, hydrophobic (phytosterols or Vitamin D₃) and hydrophilic (Vitamin B₁₂) molecules were incorporated in double emulsions prepared either with a liquid (soybean oil - SO) or oil-fat gel (soybean oil+trimyristin - STO) lipid phase and liquid internal aqueous phase. In addition, the impact of a gelled inner aqueous phase was studied, using high methoxyl pectin. W₁/O/W₂ emulsions were prepared with polyglycerol polyricinoleate (PGPR) and sodium caseinate as emulsifiers. After the 30min in vitro gastric stage, all double emulsions showed no significant change in size. Lipid crystals were visible in the STO emulsions. Fat crystallization, and the formation of an oil fat gel, led to coalescence of the inner aqueous droplets. The inner aqueous droplets were no longer visible by confocal microscopy after the initial stages of 2h in vitro duodenal digestion. Fat crystals and droplets of non-spherical shape were also noted in the STO double emulsions up to 25min of in vitro duodenal stage. Overall, the STO emulsions had a higher extent of free fatty acid release and consequent bioactive transfer compared to the SO emulsions. The presence of the medium chain fatty acids (from trimyristin), in addition to the surface-to-core distribution of the hydrophobic bioactives within the oil droplet were key factors in lipid digestibility and bioactive release. The STO and SO samples did not differ in terms of the release of the hydrophilic molecule, vitamin B₁₂, over time. On the other hand, there was a significant increase in the stability of the inner water phase, after gastric digestion, when this phase was gelled with high methoxyl pectin. This work demonstrated that the physical properties of the different internal phases of W₁/O/W₂ influenced lipid digestion and bioactive transfer kinetics during in vitro digestion.

Different magnesium release profiles from W/O/W emulsions based on crystallized oils

Water-in-oil-in-water (W/O/W) double emulsions based on crystallized oils were prepared and the release kinetics of magnesium ions from the internal to the external aqueous phase was investigated at T=4°C, for different crystallized lipophilic matrices. All the emulsions were formulated using the same surface-active species, namely polyglycerol polyricinoleate (oil-soluble) and sodium caseinate (water-soluble). The external aqueous phase was a lactose or glucose solution at approximately the same osmotic pressure as that of the inner droplets, in order to avoid osmotic water transfer phenomena. We investigated two types of crystallized lipophilic systems: one based on blends of cocoa butter and miglyol oil, exploring a solid fat content from 0 to 90% and the other system based on milk fat fractions for which the solid fat content varies between 54 and 86%. For double emulsions based on cocoa butter/miglyol oil, the rate of magnesium release was gradually lowered by increasing the % of fat crystals i.e. cocoa butter, in agreement with a diffusion/permeation mechanism. However for double emulsions based on milk fat fractions, the rate of magnesium release was independent of the % of fat crystals and remains the one at t=0. This difference in diffusion patterns, although the solid content is of the same order, suggests a different distribution of fat crystals within the double globules: a continuous fat network acting as a physical barrier for the diffusion of magnesium for double emulsions based on cocoa butter/miglyol oil and double globule/water interfacial distribution for milk fat fractions based double emulsions, through the formation of a crystalline shell allowing an effective protection of the double globules against diffusion of magnesium to the external aqueous phase.

The effects of biomacromolecules on the physical stability of W/O/W emulsions

The effect of bovine serum albumin (BSA), whey protein isolate (WPI), whey protein hydrolysate (WPH), sodium caseinate (SC), carboxymethylcellulose sodium (CMC), fish gelatin (FG), high methoxyl apple pectin (HMAP), low methoxyl apple pectin (LMAP), gum Arabic (GA), ι-carrageenan (CGN), and hydroxypropyl chitosan (HPCTS) on physical stability of internal or external aqueous phase of water-in-oil-in-water (W/O/W) emulsions was evaluated. WPI and CGN in the internal aqueous phase, and GA, HPCTS, and CMC in the external phase reduced the size of emulsion droplets. BSA, WPI, SC, FG, CGN, and HPCTS improved the dilution stability of W/O/W emulsions, but HMAP had a negative effect. BSA, WPI, SC, FG, LMAP, GA, CGN, HPCTS, or CMC significantly improved the thermal stability of W/O/W emulsions. Results also indicated that the addition of CGN (1.0%), HMAP (1.0%), WPH (1.0%), or HPCTS (1.0%) in internal aqueous phase significantly increased the viscosity of emulsions, however, addition to the external aqueous phase had insignificant effects. A protein-knockout experiment confirmed that proteins as biomacromolecules, were the key factor in improving physical stability of emulsions.

Effects of Several Natural Macromolecules on the Stability and Controlled Release Properties of Water-in-Oil-in-Water Emulsions

Water-in-oil-in-water (W/O/W) emulsions are effective vehicles for embedding application of active compounds but limited by their thermodynamic instability and rapid release properties. The present study added bovine serum albumin, whey protein isolate, whey protein hydrolysate, sodium caseinate, carboxymethylcellulose sodium, fish gelatin, apple pectin, gum arabic, ι-carrageenan, and hydroxypropyl chitosan separately to the internal or external aqueous phase to investigate their effects on the physical stabilities and controlled release properties of W/O/W emulsions. The effects of the natural macromolecules in the internal and external aqueous phases were different and depended upon the macromolecule structure and its mass fraction. The addition of the natural macromolecule strengthened the interfaces of emulsions, which improved the physical stability. The natural macromolecules that improved the stability often did not improve controlled release. Therefore, the balance between these properties needs to be considered when adding natural macromolecules to a W/O/W emulsion.

Descriptive sensory profiling of double emulsions with gelled and non-gelled inner water phase

The use of double emulsions (w₁/o/w₂) has been acknowledged as a promising strategy to reduce oil content in several food applications. Despite the potential of double emulsions for oil reduction, their sensory properties have not been investigated. In this study, we investigated sensory perception of double emulsions by descriptive sensory profiling using a trained panel (n=11). Two sets of emulsions with either 30 or 50% dispersed phase fraction were studied. Each set differed in composition (gelled and non-gelled inner w₁ phase, gelatin as gelling agent) and fat reduction level (30 to 50%), but was similar in oil droplet size and viscosity. Fat reduction level depended on the amount of water droplets entrapped inside the oil droplets. Emulsions were evaluated on nine attributes describing taste (T), mouth-feel (MF) and after-feel (AF) perception, including thickness (MF), creaminess (MF, AF), fattiness (MF, AF), and cohesiveness (MF). The replacement of oil by small water droplets w₁ did not decrease the intensity of fat-related attributes. When inner w₁ droplets were gelled, 47wt.% of oil could be replaced while increasing the intensity of fat-related attributes. This indicates that the sensory perception of single and double emulsions with gelled and non-gelled w₁ phase is mainly determined by the total oil droplet surface area. The composition of the inner water phase (gelled or not) also influences the sensory perception of double emulsions. We conclude that fat reduction up to 47wt.% can be achieved in double emulsions while maintaining or enhancing fat-related sensory perception.

Crocin loaded nano-emulsions: Factors affecting emulsion properties in spontaneous emulsification

Spontaneous emulsification may be used for encapsulating bioactive compounds in food and pharmaceutical industry. It has several advantages over high energy and other low energy methods including, protecting sensitive compounds against severe conditions of high energy method and its ability to minimize surfactant, removal of cosurfactant and thermal stability compared with other low energy methods. In this study, we examined possibility of encapsulating highly soluble crocin in W/O micro-emulsions using spontaneous method which further could be used for making double emulsions. Nonionic surfactants of Span 80 and polyglycerol polyricinoleate (PGPR) were used for making micro-emulsions that showed the high potential of PGPR for spontaneous method. Surfactant to water ratio (SWR%) was evaluated to find the highest amount of aqueous phase which can be dispersed in organic phase. Droplet size decreased by increasing SWR toward the SWR=100% which had the smallest droplet size and then increased at higher levels of surfactant. By increasing SWR, shear viscosity increased which showed the high effect of PGPR on rheological properties. This study shows in addition to W/O micro-emulsions, spontaneous method could be used for preparing stable O/W micro-emulsions.

Optimization and development of stable w/o/w cosmetic multiple emulsions by means of the Quality by Design approach

OBJECTIVES

The aim of our present work was to develop stable water-in-oil-in-water (w/o/w) cosmetic multiple emulsions that are proper for cosmetic use and can also be applied on the skin as pharmaceutical vehicles by means of Quality by Design (QbD) concept. This product design concept consists of a risk assessment step and also the 'predetermination' of the critical material attributes and process parameters of a stable multiple emulsion system. We have set up the hypothesis that the stability of multiple emulsions can be improved by the development based on such systematic planning - making a map of critical product parameters - so their industrial usage can be increased.

METHODS

The risk assessment and the determination of critical physical-chemical stability parameters of w/o/w multiple emulsions to define critical control points were performed by means of quality tools and the leanqbd(™) (QbD Works LLC, Fremont, CA, U.S.A.) software.

RESULTS

Critical materials and process parameters: Based on the results of preformulation experiments, three factors, namely entrapped active agent, preparation methodology and shear rate, were found to be highly critical factors for critical quality attributes (CQAs) and for stability, whereas the nature of oil was found a medium level risk factor. The results of the risk assessment are the following: (i) droplet structure and size distribution should be evaluated together to be able to predict the stability issues, (ii) the presence of entrapped active agents had a great impact on droplet structure, (iii) the viscosity curves represent the structural changes during storage, if the decrease in relative viscosity is >15% the emulsion disintegrates, and (iv) it is enough to use the shear rate between 34g and 116g relative centrifugal force (RCF). CQAs: By risk assessment, we discovered that four factors should be considered to be high-risk variables as compared to others: droplet size, droplet structure, viscosity and multiple character were found to be highly critical attributes.

CONCLUSION

The preformulation experiment is the part of a development plan. On the basis of these results, the control strategy can be defined and a stable multiple emulsion can be ensured that meets the relevant stakeholders' quality expectations.

Encapsulation, protection, and release of hydrophilic active components: potential and limitations of colloidal delivery systems

There have been major advances in the development of edible colloidal delivery systems for hydrophobic bioactives in recent years. However, there are still many challenges associated with the development of effective delivery systems for hydrophilic bioactives. This review highlights the major challenges associated with developing colloidal delivery systems for hydrophilic bioactive components that can be utilized in foods, pharmaceuticals, and other products intended for oral ingestion. Special emphasis is given to the fundamental physicochemical phenomena associated with encapsulation, stabilization, and release of these bioactive components, such as solubility, partitioning, barriers, and mass transport processes. Delivery systems suitable for encapsulating hydrophilic bioactive components are then reviewed, including liposomes, multiple emulsions, solid fat particles, multiple emulsions, biopolymer particles, cubosomes, and biologically-derived systems. The advantages and limitations of each of these delivery systems are highlighted. This information should facilitate the rational selection of the most appropriate colloidal delivery systems for particular applications in the food and other industries.