pH-dependent swelling and antibiotic release from citric acid crosslinked poly(vinyl alcohol) (PVA)/nano silver hydrogels

Design and evaluation of fluorescent chitosan-starch hydrogel for drug delivery and sensing applications

Composite bio-based hydrogels have been obtaining a significant attention in recent years as one of the most promising drug delivery systems. In the present study, the preparation of composite chitosan-starch hydrogel using maleic acid as a cross-linker was optimized with the help of response surface methodology. The synthesized hydrogel was fluorescent owing to clustering of large number of functional groups. Different analytical techniques, including XRD, FTIR, SEM, XPS, fluorescence and BET were utilized to characterize the prepared hydrogel. XRD analysis confirmed the formation of non-crystalline hydrogel with random arrangement of macromolecular chains. The composite hydrogel exhibited good swelling percentage with pH sensitivity, hemocompatibility and degradability. BET analysis confirmed that the variation in concentration of crosslinker significantly influences the pore volume of the hydrogel. The synthesized composite chitosan-starch hydrogel was utilized as a prospective candidate for controlling drug release. Cefixime as a model drug was loaded onto the synthesized hydrogel utilizing the swelling diffusion method. SEM micrographs showed uniform distribution of drug molecules in the drug loaded hydrogel. In vitro drug release experiments indicated the swelling dependent drug release behaviour of chitosan-starch hydrogel with higher drug release at pH 7.4 (93.08 %) compared to pH 1.2 (67.85 %). The composite chitosan-starch hydrogel was able to prolong and control the drug release up to 12 h. The drug release from the hydrogel followed Korsmeyer-Peppas and Makoid-Banakar model with Fickian diffusion mechanism. Further, the composite hydrogel displayed excitation dependent fluorescence emission with most intense blue emission band at 425 nm with an excitation wavelength of 350 nm. The inclusion of cefixime drug in the hydrogel matrix significantly reduced the fluorescence intensity; the decrease was linearly correlated to the concentration of the drug. Moreover, the fluorescence emission the chitosan-starch hydrogel was found to be dependent upon pH. The synthesized hydrogel is expected to be a potential candidate for controlled drug release as well as for fluorescent sensing applications.

A review on Ag nanoparticles fabricated in microgels

In recent years, there has been growing interest in the composites of multi-responsive microgels and silver nanoparticles. This innovative hybrid system harnesses the responsive qualities of microgels while capitalizing on the optical and electronic attributes of silver nanoparticles. This combined system demonstrates a rapid response to minor changes in pH, temperature, ionic strength of the medium, and the concentration of specific biological substances. This review article presents an overview of the recent advancements in the synthesis, classification, characterization methods, and properties of microgels loaded with silver nanoparticles. Furthermore, it explores the diverse applications of these responsive microgels containing silver nanoparticles in catalysis, the biomedical field, nanotechnology, and the mitigation of harmful environmental pollutants.

Soft and flexible polyvinyl alcohol/pullulan aerogels with fast and high water absorption capacity for facial mask substrates

Facial mask substrates commonly used in skincare are often considered unhealthy and environmentally unfriendly due to their composition of premoistened nonwovens containing various preservatives. This study aims to address this issue by developing a preservative-free degradable aerogel made from polyvinyl alcohol (PVA)/pullulan (PUL) using a unidirectional freeze-drying method. The aerogels had ordered three-dimensional porous structures and exhibited desirable mechanical properties. They were soft and flexible in both dry and wet states, and their Young's moduli were comparable to that of human skin. The aerogels had high porosity, ranging from 93.0 % to 95.1 %, and exhibited a high water absorption rate and water absorption capacity (ranging from 7.5 g/g to 10.1 g/g). After 30 min of water evaporation, the aerogels showed excellent moisture retention, ranging from 88 % to 93 %. Additionally, the PVA/PUL aerogel efficiently loaded and released active ingredients, such as rapidly releasing ascorbic acid (> 90 % within 30 min). These findings suggest that the PVA/PUL aerogel has potential as a material for facial mask substrates.

Influence of Chemical Nature of Citric and Tartaric Acids on Reaction Time of the Crosslinking of Polyvinyl Alcohol Hydrogels

Poly(vinyl alcohol) (PVOH) is a water-soluble polymer having a hydroxyl group as a functional group contributing to excellent membrane-forming and mechanical performance. PVOH is obtained by the hydrolysis of polyvinyl acetate, and its physical properties are affected by its degree of hydrolysis, whether, partial or complete. In this study, PVOH hydrogels were synthesized by a solution under stirring and heating techniques with citric (AC) and tartaric acids (AT) crosslinker agents, with different time reactions of 20 min.; 1; 2, and 3 h were investigated. These samples were characterized by the kinetics of water uptake, gel fraction, thermal analysis, and physical-chemical analysis, and their structure was elucidated. The results obtained have shown chemical modification by organic acids and improved the properties to good thermal stability and swelling to AT hydrogels up to 900% water uptake. In the gel fraction, the samples' esterification was shown and verified by FTIR spectra. To AC hydrogels the chemical modification was low due to the steric hindrance, which caused disintegration of the hydrogel in swelling and gel fraction test, but with absorption in the moisture test performed. The incorporation and effects of citric and tartaric acids enable the development of new hydrogel systems, with specific properties.

Chitosan based hybrid superabsorbent for controlled drug delivery application

In the present study, a hybrid chitosan-alginate superabsorbent is prepared using maleic acid as a cross-linker and acrylamide as a grafting agent using the free radical mechanism. The composite hydrogel shows good swelling capacity along with hemocompatibility and biocompatibility and hence it is utilized as a drug delivery device. The characterization techniques including x-ray diffraction, Fourier transform infrared, x-ray photoelectron spectroscopy, and thermal analysis indicate the successful synthesis of stable hydrogel with rich functionalities. Metformin hydrochloride is used as a model drug which is used to treat diabetes. The drug encapsulation is done using the swelling diffusion method after the synthesis of hydrogel. The release of metformin from the drug-loaded hydrogel at physiological pH highlights the role of non-covalent interactions between the drug and hydrogel. In vitro release studies of Metformin from the drug-loaded hydrogel show higher release profiles at intestinal pH (7.4) compared to stomach pH (1.2). The observed cumulative release is 82.71% at pH 7.4 and 45.67% at pH 1.2 after 10 h. Brunauer-Emmett-Teller analysis reveals the effect of surface area, pore size, and pore volume of hydrogel on the drug release. The drug release from the hybrid chitosan-alginate hydrogel is found to be more sustained in comparison to the pure chitosan hydrogel. For the present drug delivery system, the swelling-controlled release is found to be more dominating than the pH-controlled release. The synthesized hydrogel can be successfully employed as a potential drug delivery system for controlled drug delivery.

Functional Hydrogels for Delivery of the Proteolytic Enzyme Serratiopeptidase

Hydrogels are superior wound dressings because they can provide protection and hydration of the wound, as well as the controlled release of therapeutic substances to aid tissue regeneration and the healing process. Hydrogels obtained from natural precursors are preferred because of their low cost, biocompatibility, and biodegradability. We describe the synthesis of novel functional hydrogels based on two natural products-citric acid (CA) and pentane-1,2,5-triol (PT, a product from lignocellulose processing) and poly(ethylene glycol) (PEG-600)-via an environment friendly approach. The hydrogels were prepared via monomer crosslinking through a polycondensation reaction at an elevated temperature in the absence of any solvent. The reagents were blended at three different compositions with molar ratios of hydroxyl (from PT and PEG) to carboxyl (from CA) groups of 1:1, 1:1.4, and 1.4:1, respectively. The effect of the composition on the physicomechanical properties of materials was investigated. All hydrogels exhibited pH-sensitive behavior, while the swelling degree and elastic modulus were dependent on the composition of the polymer network. The proteolytic enzyme serratiopeptidase (SER) was loaded into a hydrogel via physical absorption as a model drug. The release profile of SER and the effects of the enzyme on healthy skin cells were assessed. The results showed that the hydrogel carrier could provide the complete release of the loaded enzyme.

Design and Evaluation of Liposomal Sulforaphane-Loaded Polyvinyl Alcohol/Polyethylene Glycol (PVA/PEG) Hydrogels as a Novel Drug Delivery System for Wound Healing

Hydrogel scaffold has been widely applied as drug delivery systems for treating skin injuries. However, the poor drug loading and rapid drug release of hydrogel restricted their application. In the current study, we present a nanoliposome containing sulforaphane (SF) as a nano-drug delivery system that is encapsulated within the scaffold hydrogel system to overcome these limitations and improve wound healing. The hydrogel substrate consisting of 10% polyvinyl alcohol (PVA)/5% polyethylene glycol 400 (PEG400) was prepared by the freeze-thaw method, and the nanoliposomal system was manufactured by the thin film hydration method at different molar ratios of cholesterol: SPC: DPPC: DSPE-PEG2000. The nanoliposome and hydrogel system was characterized by physicochemical analyses. The findings achieved from the optimization of the sulforaphane-loaded nanoliposome (SFNL) displayed an increase in the molar ratio of SPC, leading to a higher entrapment efficiency and a gradual release profile. Narrow size distribution, optimal electrical charge, and the lack of molecular interactions between SF and nanoliposome components in the FTIR analysis make SFNL a suitable drug delivery system for the wound healing process. The obtained SFNL-encapsulated freeze-thawed hydrogel system has sufficient and specific swelling ability at different pH values and increased mechanical strength and elongation. Additionally, the release pattern of SFNL at different pH values showed that the release of SF from liposomes depends on the pH value of the environment and accelerates in line with decreasing pH values. Encapsulation of nanoliposomal SF in the hydrogel structure provides a sustained release pattern of SF compared to its free form and increased as the pH environments continued to raise. The cytotoxicity and cell uptake of SFNL-loaded hydrogels against human skin fibroblasts (HFF cell line) were investigated. The in vitro analyses displayed that the toxicity properties of SF and SFNL were dose-dependent, and SFNL exhibited lower toxicity compared to free SF. Furthermore, the proper cell compatibility of the prepared hydrogel against the HFF cell line was confirmed by the MTT assay. These findings imply that the hydrogel scaffold loaded with SFNL may have wound-healing potential.

Research progress of nanoparticle targeting delivery systems in bacterial infections

Bacterial infection is a huge threat to the health of human beings and animals. The abuse of antibiotics have led to the occurrence of bacterial multidrug resistance, which have become a difficult problem in the treatment of clinical infections. Given the outstanding advantages of nanodrug delivery systems in cancer treatment, many scholars have begun to pay attention to their application in bacterial infections. However, due to the similarity of the microenvironment between bacterial infection lesions and cancer sites, the targeting and accuracy of traditional microenvironment-responsive nanocarriers are questionable. Therefore, finding new specific targets has become a new development direction of nanocarriers in bacterial prevention and treatment. This article reviews the infectious microenvironment induced by bacteria and a series of virulence factors of common pathogenic bacteria and their physiological functions, which may be used as potential targets to improve the targeting accuracy of nanocarriers in lesions.

Design and fabrication of dysprosium impregnated polyvinyl alcohol hydrogels. Physiochemical, mechanical, bioimaging and in vitro evaluation

Tissue engineering has gained prominence during the past decade since it offers a key solution to defects associated with the tissue regeneration. The limited healing potential of the cartilage tissue damage has significant clinical implications. Herein, dysprosium (Dy3+) impregnated polyvinyl alcohol (PVA) hydrogels have been developed to enhance the therapeutic efficacy, enabling simultaneous diagnostic imaging and antibacterial drug delivery for potential applications in articular cartilage. Based on the favorable imaging features, Dy3+ impregnated PVA hydrogels with enhanced stability were formed through successive steps of repeated cycles of freezing at - 30 °C for 21 h, thawing at 25 °C for 4 h and lyophilization. The tensile and compression tests of the hydrogels respectively determined a maximum of 3.88 and 1.58 MPa, which reflected better compatibility towards cartilage. The hydrogels fetched a sustained drug release for a period of 12 h with an associated swelling ratio of 80%. The potential of the resultant hydrogels in image diagnosis has been deliberated through their blue and yellow emissions in the visible region. Further, the computed tomography (CT) and magnetic resonance imaging characteristics of the hydrogels respectively accomplished a maximum of 343 Hounsfiled units (HU) and relaxivity of 7.25 mM-1s-1. The cytocompatibility of the hydrogels is also determined through in vitro tests performed in Murine pro B cell line (BA/F3) and human Megakaryocyte cell line (Mo7e) cell lines.

Polymer based dual drug delivery system for targeted treatment of fluoroquinolone resistant Staphylococcus aureus mediated infections

The present study attempts to treat S. aureus-induced soft skin infections using a combinatorial therapy with an antibiotic, Ciprofloxacin (CIP), and an efflux pump inhibitor 5-Nitro-2-(3-phenylpropoxy) pyridine (5-NPPP) through a smart hydrogel delivery system. The study aims to reduce the increasing rates of infections and antimicrobial resistance; therefore, an efflux pump inhibitor molecule is synthesized and delivered along with an antibiotic to re-sensitize the pathogen towards antibiotics and treat the infections. CIP-loaded polyvinyl alcohol (PVA) hydrogels at varying concentrations were fabricated and optimized by a chemical cross-linking process, which exhibited sustained drug release for 5 days. The compound 5-NPPP loaded hydrogels provided linear drug release for 2 days, necessitating the need for the development of polymeric nanoparticles to alter the release drug pattern. 5-NPPP loaded Eudragit RSPO nanoparticles were prepared by modified nanoprecipitation-solvent evaporation method, which showed optimum average particle size of 230-280 nm with > 90% drug entrapment efficiency. The 5-NPPP polymeric nanoparticles loaded PVA hydrogels were fabricated to provide a predetermined sustained release of the compound to provide a synergistic effect. The selected 7% PVA hydrogels loaded with the dual drugs were evaluated using Balb/c mice models induced with S. aureus soft skin infections. The results of in vivo studies were evidence that the dual drugs loaded hydrogels were non-toxic and reduced the bacterial load causing re-sensitization towards antibiotics, which could initiate re-epithelization. The research concluded that the PVA hydrogels loaded with CIP and 5-NPPP nanoparticles could be an ideal and promising drug delivery system for treating S. aureus-induced skin infections.

Development of a Green Polymeric Membrane for Sodium Diclofenac Removal from Aqueous Solutions

Water-soluble polymers provide an alternative to organic solvent requirements in membrane manufacture, aiming at accomplishing the Green Chemistry principles. Poly(vinyl alcohol) (PVA) is a biodegradable and non-toxic polymer renowned for its solubility in water. However, PVA is little explored in membrane processes due to its hydrophilicity, which reduces its stability and performance. Crosslinking procedures through an esterification reaction with carboxylic acids can address this concern. For this, experimental design methodology and statistical analysis were employed to achieve the optimal crosslinking conditions of PVA with citric acid as a crosslinker, aiming at the best permeate production and sodium diclofenac (DCF) removal from water. The membranes were produced following an experimental design and characterized using multiple techniques to understand the effect of crosslinking on the membrane performance. Characterization and filtration results demonstrated that crosslinking regulates the membranes' properties, and the optimized conditions (crosslinking at 110 °C for 110 min) produced a membrane able to remove 44% DCF from water with a permeate production of 2.2 L m^-2 h^-1 at 3 bar, comparable to commercial loose nanofiltration membranes. This study contributes to a more profound knowledge of green membranes to make water treatment a sustainable practice in the near future.

Preparation and characterization of a novel absorbent pad based on polyvinyl alcohol/gellan gum/citric acid with incorporated Perilla leaf oil nanoemulsion for chilled chicken packaging

A novel absorbent pad based on polyvinyl alcohol (PVA)/gellan gum/citric acid (CA) composite with incorporated Perilla leaf oil (PO) nanoemulsion was prepared and characterized. The esterification between PVA and CA and strong hydrogen bonds were detected. The PVA improved the tensile strength and elongation at break by 110% and 73%, respectively, whereas PO concentration ≤ 1.5 % (w/v) had little effect on the material properties. The CA and PO nanoemulsion loaded in the pads showed good antioxidant activity, and the pads with PO concentration ≥ 1.5 % (w/v) had effective antimicrobial activity against Escherichia coli and Staphylococcus aureus. The results of chilled chicken storage experiments indicated that the pad with 1.5% (w/v) PO nanoemulsion extended the shelf life of chicken to at least 9 days, demonstrating that the developed absorbent pads are potential materials for chilled chicken storage packing.

Preparation of pH-Responsive Films from Polyvinyl Alcohol/Agar Containing Cochineal for Monitoring the Freshness of Pork

This study reported the production of pH-responsive films based on 8 wt% polyvinyl alcohol solution/0.2 wt% agar solution incorporated with cochineal-loaded starch particles (CSN) (2, 4, 6 and 8 wt% on agar basis) by a casting process. Results revealed that CSN presented obvious color changes over the pH range of 2-12. FTIR, XRD spectra and SEM micrographs presented that the incorporation of CSN formed new hydrogen bonds with a matrix and a tighter network structure. A certain improvement was observed in the color stability, swelling index and functional properties (antimicrobial and antioxidant activities) but water solubility, water vapor permeability and water contact angle of the pH-responsive films were decreased by the addition of CSN. The release of cochineal was a rate-limiting step following the Korsmeyer-Peppas model. The agar/polyvinyl alcohol film containing 6% CSN (PVA/GG-6) exhibited the best sensitivity for ammonia detection and its limit of detection was 35.4 ppm (part per million) for ammonia. The application trials showed that the PVA/GG-6 film presented different color changes for pork freshness. Hence, these pH-responsive films can be used as potential packaging materials for tracking the freshness of protein-rich fresh food in a non-destructive way.

Development and In Vitro Analysis of Layer-by-Layer Assembled Membranes for Potential Wound Dressing: Electrospun Curcumin/Gelatin as Middle Layer and Gentamicin/Polyvinyl Alcohol as Outer Layers

Nanofibrous membranes made of hydrogels have high specific surface areas and are suitable as drug carriers. Multilayer membranes fabricated by continuous electrospinning could delay drug release by increasing diffusion pathways, which is beneficial for long-term wound care. In this experiment, polyvinyl alcohol (PVA) and gelatin were used as membrane substrates, and a sandwich PVA/gelatin/PVA structure of layer-by-layer membranes was prepared by electrospinning under different drug loading concentrations and spinning times. The outer layers on both sides were citric-acid-crosslinked PVA membranes loaded with gentamicin as an electrospinning solution, and the middle layer was a curcumin-loaded gelatin membrane for the study of release behavior, antibacterial activity, and biocompatibility. According to the in vitro release results, the multilayer membrane could release curcumin slowly; the release amount was about 55% less than that of the single layer within 4 days. Most of the prepared membranes showed no significant degradation during immersion, and the phosphonate-buffered saline absorption rate of the multilayer membrane was about five to six times its weight. The results of the antibacterial test showed that the multilayer membrane loaded with gentamicin had a good inhibitory effect on Staphylococcus aureus and Escherichia coli. In addition, the layer-by-layer assembled membrane was non-cytotoxic but detrimental to cell attachment at all gentamicin-carrying concentrations. This feature could be used as a wound dressing to reduce secondary damage to the wound when changing the dressing. This multilayer wound dressing could be applied to wounds in the future to reduce the risk of bacterial infection and help wounds heal.

Eco-Friendly Semi-Interpenetrating Polymer Network Hydrogels of Sodium Carboxymethyl Cellulose/Gelatin for Methylene Blue Removal

The present work describes the potential application of environmentally friendly sodium carboxymethylcellulose/gelatin (CMC/Gel) semi-interpenetrating hydrogels prepared by citric acid as a nontoxic cross-linking agent to adsorb dyes. The prepared hydrogels were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA/DTG), and swelling study. The adsorption performance of CMC/Gel2 (C/G2) hydrogel on methylene blue (MB) was investigated. The results showed the better adsorption conditions: adsorption time of 300 min, initial MB concentration of 500 mg/L, adsorbent dosage of 1.2 g/L, solution pH of 7, and temperature of 30 °C. The adsorption kinetics fit the pseudo-second order kinetics model, and the adsorption isotherm fit the Langmuir isotherm model. The maximum adsorption capacity reached 943.40 mg/g. The adsorption process is a spontaneous exothermic process. After three adsorption-desorption cycles, the removal rate of MB by hydrogel still reached 85%, with good reusability. Consequently, the hydrogel can be used as an environmentally friendly, stable, and efficient adsorbent for dyes in wastewater treatment.

Folic acid-decorated alginate nanoparticles loaded hydrogel for the oral delivery of diferourylmethane in colorectal cancer

The disease-related suffering in colorectal cancer remains prevalent despite advancements in the field of drug delivery. Chemotherapy-related side effects and non-specificity remain a challenge in drug delivery. The great majority of hydrophobic drugs cannot be successfully delivered to the colon orally mainly due to poor solubility, low bioavailability, pH differences, and food interactions. Polymeric nanoparticles are potential drug delivery candidates but there are numerous limitations to their usefulness in colon cancer. The nanoparticles are removed from the body rapidly by p-glycoprotein efflux, inactivation, or breakdown by enzymes limiting their efficiency. Furthermore, there is a lack of selectivity in targeting cancer cells; nanoparticles may also target healthy cells, resulting in toxicity and adverse effects. The study aimed to use nanoparticles for specific targeting of the colorectal tumor cells via the oral route of administration without adverse effects. Folic acid (FA), a cancer-targeting ligand possessing a high affinity for folate receptors overexpressed in colorectal cancers was conjugated to sodium alginate- nanoparticles by NH₂-linkage. The folic-acid conjugated nanoparticles (FNPs) were delivered to the colon by a pH-sensitive hydrogel synthesized by the free radical polymerization method to provide sustained drug release. The developed system referred to as the "Hydrogel-Nano (HN) drug delivery system," was specifically capable of delivering diferourylmethane to the colon. The HN system was characterized by DLS, FTIR, XRD, TGA, DSC, and SEM. The FNPs size, polydispersity index, and zeta potential were measured. The folic acid-conjugation to nanoparticles' surface was studied by UV-visible spectroscopy using Beer-Lambert's law. In-vitro studies, including sol-gel, porosity, drug loading, entrapment efficiency, etc., revealed promising results. The swelling and release studies showed pH-dependent release of the drug in colonic pH 7.4. Cellular uptake and cytotoxicity studies performed on FR-overexpressed Hela cell lines and FR-negative A-549 cell lines showed facilitated uptake of nanoparticles by folate receptors. A threefold increase in C_max and prolongation of the mean residence time (MRT) to 14.52 +/- 0.217 h indicated sustained drug release by the HN system. The findings of the study can provide a sufficient ground that the synergistic approach of the HN system can deliver hydrophobic drugs to colorectal cancer cells via the oral route, but further in-vivo animal cancer model studies are required.

Effect of Citric Acid on Swelling Resistance and Physicochemical Properties of Post-Crosslinked Electrospun Polyvinyl Alcohol Fibrous Membrane

A series of electrospun polyvinyl alcohol (PVA) fiber membranes were crosslinked with citric acid (CA) at concentrations of 10, 20, and 30 wt.% (designated as CA10, CA20, and CA30). The effects of CA on the chemical structure, mechanical strength, swelling resistance, and cytotoxicity of the crosslinked PVA fibrous membranes were investigated. Infrared spectroscopy indicated the enhanced esterification of carboxyl and hydroxyl groups between CA and PVA. The modulus and strength of the electrospun PVA membrane increased due to the crosslinking between CA and PVA. The crosslinking of the PVA fiber matrix with CA increased the PVA binding point, thereby increasing the swelling resistance and modulus; however, the concentration of CA used was limited. Results showed that the water absorption of the PVA membranes decreased from 6.58 ± 0.04 g/g for CA10 to 3.56 ± 3.33 g/g for CA20 and 2.85 ± 0.40 g/g for CA30 with increasing CA. The water absorption remained unchanged after the membrane was soaked for a period of time, so no significant difference was found in the water absorption capacity of the same group after immersion from 1 h to 3 d. The tensile strength increased from 20.52 MPa of CA10 to 22.09 MPa of CA20. With an increased amount of CA used for crosslinking, the tensile strength and modulus of CA30 decreased to 11.48 and 13.94 MPa, respectively. Our study also showed that CA was not toxic to L929 cell viability when used for fiber crosslinking at less than 20 wt.% PVA, meaning it may be a good candidate as a support layer for guided tissue engineering.

Chitosan based smart polymer composites: Fabrication and pH-Responsive behavior for bio-medical applications

This research aimed to synthesize Chitosan/PVA-blank and a series of Cs/PVA/Sepolite based pH-sensitive membranes using a solution casting process. The synthesized Cs/PVA-blank and Cs/PVA/Sep based membranes were investigated via SEM, FTIR, XRD, and TGA techniques. The SEM results of Cs/PVA/Sep based membrane reveal that the hydrolytic stability and strength were improved in acidic and basic media owing to the incorporation of sepiolite content into chitosan. The characteristic band at 3741 cm^-1 in the FTIR spectra of the Cs/PVA/Sep membrane confirmed the successful synthesis. The obtained XRD results showed higher d-spacing for Cs/PVA/Sep membranes as compared to the Cs/PVA-blank membranes owing to the intercalation of chitosan in the interlayer spacing of the sepiolite. The obtained TGA results show higher thermally stability for Cs/PVA/Sep membrane as compared to the Cs/PVA-blank sample due to the interaction of sepiolite content with the chitosan matrix. The obtained hydrolytic and swelling studies revealed that the Cs/PVA/Sep membrane displayed enhanced stability in basic and neutral media while showing minimum swelling in an acidic medium. The water uptake ability was checked for Cs/PVA/-blank and Cs/PVA/Sep-60% membrane and the results exhibited that the Cs/PVA/-blank membrane had maximum water uptake value as compared to the Cs/PVA/Sep-60% membrane. While those with a considerable amount of filler had the lowest water uptake values. As Sepolite content increased, the water uptake % values decreases because of weakness in H-bonding (of hydrophilic groups) and due to intercalation in Sepolite layers during polymer formation.

Electroresponsive and pH-Sensitive Hydrogel as Carrier for Controlled Chloramphenicol Release

Multiresponsive hydrogels, which are smart soft materials that respond to more than one external stimulus, have emerged as powerful tools for biomedical applications, such as drug delivery. Within this context and with the aim of eliminating the systematic administration of antibiotics, special attention is being paid to the development of systems for controlled delivery of antibiotic for topical treatment of bacterial infections. In this work, an electro-chemo responsive hydrogel able to release chloramphenicol (CAM), a broad spectrum antibiotic also used for anticancer therapy, is proposed. This has been prepared by grafting poly(acrylic acid) (PAA) to sodium alginate (Alg) and in situ encapsulation of poly(3,4-ethylenedioxythiophene) nanoparticles loaded with CAM (PEDOT/CAM NPs), which were obtained by emulsion polymerization. Although the response to electrical stimuli of PEDOT was the main control for the release of CAM from PEDOT/CAM NPs, the release by passive diffusion had a relatively important contribution. Conversely, the passive release of antibiotic from the whole engineered hydrogel system, Alg-g-PAA/PEDOT/CAM, was negligible, whereas significant release was achieved under electrostimulation in an acid environment. Bacterial tests and assays with cancer cells demonstrated that the biological activity of CAM remained after release by electrical stimulation. Notably, the successful dual-response of the developed hydrogel to electrical stimuli and pH changes evidence the great prospect of this smart material in the biomedical field, as a tool to fight against bacterial infections and to provide local cancer treatment.

Fabricating gum polysaccharides based nano-composites for drug delivery uses via sustainable green approach

Recent advancements in development of natural polymer nono-composites led to exploration of potential of gum acacia (GA) and tragacanth gum (TG) for design of silver nanoparticles (AgNPs) impregnated grafted copolymers via green approach for use in drug delivery (DD). The formation of copolymers was confirmed by UV-Vis spectroscopy, TEM, SEM, AFM, XPS, XRD, FTIR,TGA and DSC. UV-Vis spectra indicated the formation of AgNPs using GA as reducing agent. TEM, SEM, XPS and XRD revealed impregnation of AgNPs inside the copolymeric network hydrogels. TGA inferred thermal stability of polymer enhanced by grafting and incorporation of AgNPs. The non-Fickian diffusion of antibiotic drug meropenem was revealed from drug encapsulated GA-TG-(AgNPs)-cl-poly(AAm) network which were also pH responsive and release profile was fitted in Korsmeyer-Peppas kinetic model. Sustained release was due to polymer-drug interaction. The polymer-blood interaction demonstrated biocompatible characteristics of polymer. Mucoadhesive property exhibited by copolymers because of supra-molecular interactions. Antimicrobial characteristics were shown by copolymers against bacteria S. flexneri, P. auroginosa, and B. cereus.

Emerging nanoparticle designs against bacterial infections

The rise of antibiotic resistance has caused the prevention and treatment of bacterial infections to be less effective. Therefore, researchers turn to nanomedicine for novel and effective antibacterial therapeutics. The effort resulted in the first-generation antibacterial nanoparticles featuring the ability to improve drug tolerability, circulation half-life, and efficacy. Toward developing the next-generation antibacterial nanoparticles, researchers have integrated design elements that emphasize physical, broad-spectrum, biomimetic, and antivirulence mechanisms. This review highlights four emerging antibacterial nanoparticle designs: inorganic antibacterial nanoparticles, responsive antibacterial nanocarriers, virulence nanoscavengers, and antivirulence nanovaccines. Examples in each design category are selected and reviewed, and their structure-function relationships are discussed. These emerging designs open the door to nontraditional antibacterial nanomedicines that rely on mechano-bactericidal, function-driven, nature-inspired, or virulence-targeting mechanisms to overcome antibiotic resistance for more effective antibacterial therapy. This article is categorized under: Therapeutic Approaches and Drug Discovery > Nanomedicine for Infectious Disease.

Coherent Loading-Deloading Mechanism in Polymeric Nanohybrid Network Structures

Physically cross-linked gels have unique advantages of repeated swelling and shrinking of network structures, where the stability of gels at the swelled phase, particularly under ionic conditions, is extremely critical. In this study, it has been shown that functionalized nanofillers and polar solvents can increase the network densities of physically cross-linked gels with higher dimensional stability by increasing the polar and electrostatic interactions. The characteristic nonbonded interactions of CNTs with ionic solvents have been utilized for the controlled swelling of toughened double-network gels as the function of pH and time. The swelling of the overall gel morphology is found to be important for the release of analytes; however, the functional cross-sectional sites in the nanohybrids hold the key for desorption kinetics. The selection of interactive functional moieties in the nanohybrids and analytes has led to the development of highly efficient and controlled release media. The electrostatic interaction of analytes with functionally and dimensionally stable gels with controlled porosity indicates a clear structure-property correlation, which could be exploited to design and fabricate efficient drug delivery vehicles and rapid surface decontaminants.

Cellulose nanofibrils reinforced chitosan-gelatin based hydrogel loaded with nanoemulsion of oregano essential oil for diabetic wound healing assisted by low level laser therapy

Diabetic foot ulcers are imperfections in the process of wound healing due to hyperglycemic conditions. Here, a nanoemulgel fabricated with oregano essential oil nanoemulsion, assisted by low-level laser therapy, was investigated for its efficacy in diabetic wound healing. A hydrogel- based healing patch, fabricated using biological polymers namely chitosan and gelatin and, polyvinyl pyrollidone. The hydrogel was reinforced with cellulose nanofibrils for enhanced stability and barrier properties. Nanoemulsion of oregano essential oil, with an average particle size of 293.7 ± 8.3 nm, was prepared via homogenization with chitosan as the coating agent. Nanoemulsion impregnated hydrogel, termed as the nanoemulgel, was assessed for its physio-mechanical properties and healing efficiency. The strong linkages in nanoemulgel demonstrated its large swelling capacity, high mechanical strength, and maximum thermal stability. The optimized conditions for low-level laser therapy using 808 nm were 1 W. cm^-2 and 5 min. The optimized drug concentration of 128 μg. mL^-1 exhibited viability of NIH/3 T3 fibroblasts as 75.5 ± 1.2 % after 24 h. Cell migration assay demonstrated that dual therapy facilitated wound healing, with a maximum closure rate of 100 % at 48 h. In vivo results revealed the rapid healing effects of the dual therapy in diabetic rat models with foot ulcers: a maximum healing rate of 97.5 %, minimum scar formation, increased granulation, enhanced reepithelialization, and a drastic decrease in inflammation and neutrophil infiltration within the treatment period compared to monotherapy and control. In summary, the combinatorial therapy of nanoemulgel and low-level laser therapy is a promising regimen for managing diabetic foot ulcers with a rapid healing effect.

Novel Nanocomposite Hydrogels Based on Crosslinked Microbial Polysaccharide as Potential Bioactive Wound Dressings

A multitude of dressings have been developed to promote wound repair, such as membranes, foams, hydrocolloids and hydrogels. In this study, a crosslinked polysaccharide hydrogel was mixed with a bioactive ingredient to synthesize a novel nanocomposite material to be used in wound healing. Variation of the ratio between hydrogel components was followed and its effect was analyzed in regard to swelling, degradation rate and thermo-mechanical behavior. The resulting crosslinked structures were characterized by FTIR and microscopy analyses. The antimicrobial activity of the crosslinked hydrogels loaded with bioactive agent was evaluated using two bacterial strains (Gram-positive Staphylococcus aureus and Gram-negative bacteria Escherichia Coli). All the results showed that the new synthesized biopolymer nanocomposites have adequate properties to be used as antibacterial wound dressings.

Preparation of hydroxypropyl starch/polyvinyl alcohol composite nanofibers films and improvement of hydrophobic properties

Starch-derived edible films have great potential as biodegradable food packaging and biomedical materials, in this study, we adopted a green method to prepare starch-based composite electrospun nanofibers films. The hydroxypropyl starches (HPS) were prepared to improve native starch solubility and properties, and a series of blend solutions were prepared with different HPS/polyvinyl alcohol (PVA) weight ratios. The comparison of the properties of HPS/PVA (HPA) nanofibers with different amylose contents were evaluated, and the fibers fabricated from hydroxypropyl high amylose starch (HP-HAS) had more continuous and homogeneous morphologies compared to the other starch fibers, it was also found that the addition of HP-HAS in the film has better mechanical properties than pure PVA film. Thus, to improve the hydrophobicity of the film, the HP-HAS/PVA (HPA(H)) nanofiber was selected for the hydrophobic study by the citric acid (CA) treatment. The hydrophobic surface was formed on the HPA(H) film by CA self-assembled coating with a water contact angle changed from 30.95° up to 100.74°. This study successfully prepared the modified starch/PVA composite nanofibers and established a simple method of self-assembled hydrophobic modification to improve water stability. Therefore, this green strategy is an alternative candidate in further study for food packaging and relative areas.

The resistance mechanisms of bacteria against ciprofloxacin and new approaches for enhancing the efficacy of this antibiotic

For around three decades, the fluoroquinolone (FQ) antibiotic ciprofloxacin has been used to treat a range of diseases, including chronic otorrhea, endocarditis, lower respiratory tract, gastrointestinal, skin and soft tissue, and urinary tract infections. Ciprofloxacin's main mode of action is to stop DNA replication by blocking the A subunit of DNA gyrase and having an extra impact on the substances in cell walls. Available in intravenous and oral formulations, ciprofloxacin reaches therapeutic concentrations in the majority of tissues and bodily fluids with a low possibility for side effects. Despite the outstanding qualities of this antibiotic, Salmonella typhi, Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa have all shown an increase in ciprofloxacin resistance over time. The rise of infections that are resistant to ciprofloxacin shows that new pharmacological synergisms and derivatives are required. To this end, ciprofloxacin may be more effective against the biofilm community of microorganisms and multi-drug resistant isolates when combined with a variety of antibacterial agents, such as antibiotics from various classes, nanoparticles, natural products, bacteriophages, and photodynamic therapy. This review focuses on the resistance mechanisms of bacteria against ciprofloxacin and new approaches for enhancing its efficacy.

Aggressive strategies for regenerating intervertebral discs: stimulus-responsive composite hydrogels from single to multiscale delivery systems

As our research on the physiopathology of intervertebral disc degeneration (IVD degeneration, IVDD) has advanced and tissue engineering has rapidly evolved, cell-, biomolecule- and nucleic acid-based hydrogel grafting strategies have been widely investigated for their ability to overcome the harsh microenvironment of IVDD. However, such single delivery systems suffer from excessive external dimensions, difficult performance control, the need for surgical implantation, and difficulty in eliminating degradation products. Stimulus-responsive composite hydrogels have good biocompatibility and controllable mechanical properties and can undergo solution-gel phase transition under certain conditions. Their combination with ready-to-use particles to form a multiscale delivery system may be a breakthrough for regenerative IVD strategies. In this paper, we focus on summarizing the progress of research on the stimulus response mechanisms of regenerative IVD-related biomaterials and their design as macro-, micro- and nanoparticles. Finally, we discuss multi-scale delivery systems as bioinks for bio-3D printing technology for customizing personalized artificial IVDs, which promises to take IVD regenerative strategies to new heights.

Drug Delivery Strategies and Biomedical Significance of Hydrogels: Translational Considerations

Hydrogels are a promising and attractive option as polymeric gel networks, which have immensely fascinated researchers across the globe because of their outstanding characteristics such as elevated swellability, the permeability of oxygen at a high rate, good biocompatibility, easy loading, and drug release. Hydrogels have been extensively used for several purposes in the biomedical sector using versatile polymers of synthetic and natural origin. This review focuses on functional polymeric materials for the fabrication of hydrogels, evaluation of different parameters of biocompatibility and stability, and their application as carriers for drugs delivery, tissue engineering and other therapeutic purposes. The outcome of various studies on the use of hydrogels in different segments and how they have been appropriately altered in numerous ways to attain the desired targeted delivery of therapeutic agents is summarized. Patents and clinical trials conducted on hydrogel-based products, along with scale-up translation, are also mentioned in detail. Finally, the potential of the hydrogel in the biomedical sector is discussed, along with its further possibilities for improvement for the development of sophisticated smart hydrogels with pivotal biomedical functions.

Antiacne Effects of PVA/ZnO Composite Nanofibers Crosslinked by Citric Acid for Facial Sheet Masks

The water-insoluble polyvinyl alcohol (PVA) nanofibers containing ZnO nanoparticles were prepared by an electrospinning technique for antiacne facial masks. Zinc oxide (ZnO) nanoparticles prepared by a sol-gel method were dispersed in aqueous PVA and citric acid solution for electrospinning. The electrospun nanofibers were treated at 160°C to induce the thermal crosslinking between PVA and citric acid. The crosslinked PVA with citric acid become water-insoluble, which can be used for facial masks. PVA/ZnO composite nanofibers were characterized by structural and morphological analysis techniques including Fourier transform infrared spectroscopy (FT-IR), field-emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). Also, the swelling ratios according to the ZnO content (0, 1, 4, and 7 wt.% with respect to PVA) were measured. Antibacterial activity tests were also studied. The clear zone of Cutibacterium acnes of PVA/ZnO 7% nanofibers was 2.25 mm, indicating antiacne activities of nanofibers.

Cross-Linking Combined with Surfactant Bilayer Assembly Enhances the Hydrophilic and Antifouling Properties of PTFE Microfiltration Membranes

The inherent strong hydrophobicity of Polytetrafluoroetylene (PTFE) microfiltration membranes results in low separation efficiency and easy contamination. In order to enhance its hydrophilic and antifouling properties, we first modified the PTFE microfiltration membrane by using Polyethylene glycol laurate (PEGML) for first layer deposition and then used Polyvinyl alcohol (PVA)/citric acid (CA) cross-linked coatings for second layer deposition. The Scanning Electron Microscope (SEM) results showed that the fibers and nodes of the modified PTFE microfiltration membrane were coated with PVA/CA hydrophilic coating. FT-IR Spectromete and X-ray photoelectron spectrometer (XPS) analysis results confirmed that crosslinking of PVA and CA occurred and that PEGML and PVA/CA were successfully deposited onto the membrane surface. The modification conditions were optimized by hydrophilicity testing, and the best hydrophilicity of the modified membrane was achieved when the crosslinking content of PEGML was 2 g·L−1, PVA was 5 g·L−1, and CA was 2 g·L−1. PTFE microfiltration membranes modified by the optimal conditions achieved a water flux of 396.9 L·m−2·h−1 (three times that of the original membrane) at low operating pressures (0.05 MPa), and the contact angle decreased from 120° to 40°. Meanwhile, the modified PTFE microfiltration membrane has improved contamination resistance and good stability of the hydrophilic coating.

Application or function of citric acid in drug delivery platforms

Nontoxic materials with natural origin are promising materials in the designing and preparation of the new drug delivery systems (DDSs). Today's, citric acid (CA) has attracted a great deal of attention because of its special features; green nature, biocompatibility, low price, biodegradability, and commercially available property. So, CA has been employed in the preparation of the various platforms to induce a suitable property on their structure. Recently, several research groups investigated the CA-based platforms in different forms like tablets, dendrimers, hyperbranched polymers, (co)polymer, hydrogels, and nanoparticles as efficient DDSs. By considering an increasing amount of published articles in this field, for the first time, in this review, an overview of the published works regarding CA applications in the design of various DDSs is presented with a detailed and insightful discussion.

Catalyst-Free Crosslinking Modification of Nata-de-Coco-Based Bacterial Cellulose Nanofibres Using Citric Acid for Biomedical Applications

Bacterial cellulose (BC) has gained attention among researchers in materials science and bio-medicine due to its fascinating properties. However, BC’s fibre collapse phenomenon (i.e., its inability to reabsorb water after dehydration) is one of the drawbacks that limit its potential. To overcome this, a catalyst-free thermal crosslinking reaction was employed to modify BC using citric acid (CA) without compromising its biocompatibility. FTIR, XRD, SEM/EDX, TGA, and tensile analysis were carried out to evaluate the properties of the modified BC (MBC). The results confirm the fibre crosslinking phenomenon and the improvement of some properties that could be advantageous for various applications. The modified nanofibre displayed an improved crystallinity and thermal stability with increased water absorption/swelling and tensile modulus. The MBC reported here can be used for wound dressings and tissue scaffolding.

pH-responsive antibacterial film based polyvinyl alcohol/poly (acrylic acid) incorporated with aminoethyl-phloretin and application to pork preservation

This study demonstrates a pH-responsive antibacterial film based on polyvinyl alcohol/poly (acrylic acid) incorporated with aminoethyl-phloretin (PVA/PAA-AEP) for intelligent food packaging. The thermal, mechanical, barrier and light transmittance properties of PVA/PAA are enhanced by PAA presence of ≤6%. The interactions between PVA and PAA were hydrogen and ester bonds. The pH-responsive characteristic is dependent on the protonation/deprotonation tendency of the carboxylic groups on PAA in acidic/alkaline environment. The PVA/PAA3 is selected for the incorporation of AEP and its pH-responsive swelling follows Ritger-Peppas and Schott second-order models. The AEP is hydrogen bonded with the matrix of PVA/PAA3 and the release of AEP is pH-responsive and a rate-limiting step following the First-order model. With pH decrease, the predominant release control was gradually changing from polymer relaxation to Fick diffusion. The PVA/PAA3-AEP films demonstrate AEP content dependent antioxidant and antimicrobial activities. Furthermore, the antibacterial efficiency against Listeria monocytogenes and Staphylococcus aureus is significantly better than Escherichia coli. The target film PVA/PAA3-AEP3 can effectively prolong the shelf-life of pork (TVB-N < 25 mg/100 g) by 4 days at 25 °C, suggesting its great potential in intelligent food packaging.

Pharmaceutical applications of citric acid

Background

Citric acid (CA) is a universal plant and animal-metabolism intermediate. It is a commodity chemical processed and widely used around the world as an excellent pharmaceutical excipient. Notably, CA is offering assorted significant properties viz. biodegradability, biocompatibility, hydrophilicity, safety, etc. Therefore, CA is broadly employed in many sectors including foodstuffs, beverages, pharmaceuticals, nutraceuticals, and cosmetics as a flavoring agent, sequestering agent, buffering agent, etc. From the beginning, CA is a regular ingredient for cosmetic pH-adjustment and as a metallic ion chelator in antioxidant systems. In addition, it is used to improve the taste of pharmaceuticals such as syrups, solutions, elixirs, etc. Furthermore, free CA is also employed as an acidulant in mild astringent preparations.

Main text

In essence, it is estimated that the functionality present in CA provides excellent assets in pharmaceutical applications such as cross-linking, release-modifying capacity, interaction with molecules, capping and coating agent, branched polymer nanoconjugates, gas generating agent, etc. Mainly, the center of attention of the review is to deliver an impression of the CA-based pharmaceutical applications.

Conclusion

In conclusion, CA is reconnoitered for multiple novels pharmaceutical and biomedical/applications including as a green crosslinker, release modifier, monomer/branched polymer, capping and coating agent, novel disintegrant, absorption enhancer, etc. In the future, CA can be utilized as an excellent substitute for pharmaceutical and biomedical applications.

Graphical abstract

Recent advances in functionalized nanomaterials for the diagnosis and treatment of bacterial infections

The growing problem of resistant infections due to antibiotic misuse is a worldwide concern that poses a grave threat to healthcare systems. Thus, it is necessary to discover new strategies to combat infectious diseases. In this review, we provide a selective overview of recent advances in the use of nanocomposites as alternatives to antibiotics in antimicrobial treatments. Metals and metal oxide nanoparticles (NPs) have been associated with inorganic and organic supports to improve their antibacterial activity and stability as well as other properties. For successful antibiotic treatment, it is critical to achieve a high drug concentration at the infection site. In recent years, the development of stimuli-responsive systems has allowed the vectorization of antibiotics to the site of infection. These nanomaterials can be triggered by various mechanisms (such as changes in pH, light, magnetic fields, and the presence of bacterial enzymes); additionally, they can improve antibacterial efficacy and reduce side effects and microbial resistance. To this end, various types of modified polymers, lipids, and inorganic components (such as metals, silica, and graphene) have been developed. Applications of these nanocomposites in diverse fields ranging from food packaging, environment, and biomedical antimicrobial treatments to diagnosis and theranosis are discussed.

Bio-functional hydrogel membranes loaded with chitosan nanoparticles for accelerated wound healing

Wounds are often recalcitrant to traditional wound dressings and a bioactive and biodegradable wound dressing using hydrogel membranes can be a promising approach for wound healing applications. The present research aimed to design hydrogel membranes based on hyaluronic acid, pullulan and polyvinyl alcohol and loaded with chitosan based cefepime nanoparticles for potential use in cutaneous wound healing. The developed membranes were evaluated using dynamic light scattering, proton nuclear magnetic resonance, Fourier transform infrared spectroscopy, thermogravimetric analysis, and scanning electron microscopy. The results indicated the novel crosslinking and thermal stability of the fabricated hydrogel membrane. The in vitro analysis demonstrates that the developed membrane has water vapors transmission rate (WVTR) between 2000 and 2500 g/m²/day and oxygen permeability between 7 and 14 mg/L, which lies in the range of an ideal dressing. The swelling capacity and surface porosity to liberate encapsulated drug (cefepime) in a sustained manner and 88% of drug release was observed. The cefepime loaded hydrogel membrane demonstrated a higher zone of inhibition against Staphylococcus aureus, Pseudomonas aeruginosa, and Escherichia coli and excisional rat model exhibit expeditious recovery rate. The developed hydrogel membrane loaded with cefepime nanoparticles is a promising approach for topical application and has greater potential for an accelerated wound healing process.