Electrophoretic deposition of polymethylmethacrylate and composites for biomedical applications

Research and application of surface heat treatment for CO2 continuous laser ablation of polymeric methyl methacrylate materials

Based on the influence of a filamentous laser Gaussian heat source and its movement speed on Polymeric Methyl Methacrylate materials (PMMA sheets), the physical model of heat transfer of PMMA materials by CO2 continuous laser ablation was established. Numerical simulation research on heat transfer in CO2 continuous laser processing of PMMA sheets was carried out by applying the heat transfer model, and experiments on continuous laser processing of PMMA sheets were conducted on the basis of the numerical simulation results. Theoretical and experimental research indicated that under relevant conditions, when the laser power was 20 W, the maximum surface temperature of PMMA sheet was approximately 520 K, which was higher than the melting temperature of the PMMA material, achieving the transformation of the PMMA material from solid to liquid phase in the laser ablation area. When the laser power was 40 W, the CO2 continuous laser could vaporize the PMMA material, cracking the polymer structure of polymethyl methacrylate. When the laser power was 80 W, the maximum surface temperature of the PMMA sheet was approximately 1300 K, and the processing efficiency of CO2 continuous laser ablation of the PMMA material was the highest. The above research provided theoretical guidance and process optimization for the research of CO2 continuous laser ablation of PMMA sheets. The consistency between the experimental results and the numerical simulation results demonstrated the correctness and feasibility of the theoretical model, which has certain universality and reference value for the optimization research of laser processing non-metallic materials and polymer materials.

Electro-Biofabrication. Coupling Electrochemical and Biomolecular Methods to Create Functional Bio-Based Hydrogels

Twenty years ago, this journal published a review entitled "Biofabrication with Chitosan" based on the observations that (i) chitosan could be electrodeposited using low voltage electrical inputs (typically less than 5 V) and (ii) the enzyme tyrosinase could be used to graft proteins (via accessible tyrosine residues) to chitosan. Here, we provide a progress report on the coupling of electronic inputs with advanced biological methods for the fabrication of biopolymer-based hydrogel films. In many cases, the initial observations of chitosan's electrodeposition have been extended and generalized: mechanisms have been established for the electrodeposition of various other biological polymers (proteins and polysaccharides), and electrodeposition has been shown to allow the precise control of the hydrogel's emergent microstructure. In addition, the use of biotechnological methods to confer function has been extended from tyrosinase conjugation to the use of protein engineering to create genetically fused assembly tags (short sequences of accessible amino acid residues) that facilitate the attachment of function-conferring proteins to electrodeposited films using alternative enzymes (e.g., transglutaminase), metal chelation, and electrochemically induced oxidative mechanisms. Over these 20 years, the contributions from numerous groups have also identified exciting opportunities. First, electrochemistry provides unique capabilities to impose chemical and electrical cues that can induce assembly while controlling the emergent microstructure. Second, it is clear that the detailed mechanisms of biopolymer self-assembly (i.e., chitosan gel formation) are far more complex than anticipated, and this provides a rich opportunity both for fundamental inquiry and for the creation of high performance and sustainable material systems. Third, the mild conditions used for electrodeposition allow cells to be co-deposited for the fabrication of living materials. Finally, the applications have been expanded from biosensing and lab-on-a-chip systems to bioelectronic and medical materials. We suggest that electro-biofabrication is poised to emerge as an enabling additive manufacturing method especially suited for life science applications and to bridge communication between our biological and technological worlds.

Two-Dimensional Zeolitic Imidazolate Framework ZIF-L: A Promising Catalyst for Polymerization

Here, for the first time, a 2D and leaf-like zeolitic imidazolate framework (ZIF-L) is reported for the synthesis of ultrahigh molecular weight (UHMW) poly(methyl methacrylate) (PMMA) with Mn up to 1390 kg mol−1. This synthesis method is a one-step process without any co-catalyst in a solvent-free medium. SEM, PXRD, FT-IR, TGA, and nitrogen sorption measurements confirmed the 2D and leaf-like structure of ZIF-L. The results of PXRD, SEM, TGA demonstrate that the catalyst ZIF-L is remarkably stable even after a long-time polymerization reaction. Zwitterionic Lewis pair polymerization (LPP) has been proposed for the catalytic performance of ZIF-L on methyl methacrylate (MMA) polymerization. This MMA polymerization is consistent with a living system, where ZIF-L could reinitiate the polymerization and propagates the process by gradually growing the polymer chains.

Semiconducting Polymers for Oxygen Evolution Reaction under Light Illumination

Sunlight-driven water splitting to produce hydrogen fuel has stimulated intensive scientific interest, as this technology has the potential to revolutionize fossil fuel-based energy systems in modern society. The oxygen evolution reaction (OER) determines the performance of overall water splitting owing to its sluggish kinetics with multielectron transfer processing. Polymeric photocatalysts have recently been developed for the OER, and substantial progress has been realized in this emerging research field. In this Review, the focus is on the photocatalytic technologies and materials of polymeric photocatalysts for the OER. Two practical systems, namely, particle suspension systems and film-based photoelectrochemical systems, form two main sections. The concept is reviewed in terms of thermodynamics and kinetics, and polymeric photocatalysts are discussed based on three key characteristics, namely, light absorption, charge separation and transfer, and surface oxidation reactions. A satisfactory OER performance by polymeric photocatalysts will eventually offer a platform to achieve overall water splitting and other advanced applications in a cost-effective, sustainable, and renewable manner using solar energy.

Production of photoluminescent transparent poly(methyl methacrylate) for smart windows

Photochromic and long-lasting photoluminescent transparent, rigid, ultraviolet (UV) protective and superhydrophobic poly(methyl methacrylate) (PMMA) plastic able to switch colour beneath UV irradiation was developed. Photoluminescent transparent PMMA plastic was prepared by the simple polymerization process of methyl methacrylate immobilized with alkaline earth aluminate (AEA) nanoparticles. These colourless PMMA plastic substrates showed a colour switch to greenish underneath UV light as proved using CIELAB screening. The morphology of AEA was evaluated using transmission electron microscopy. Conversely, transparent PMMA samples were evaluated using energy-dispersive X-ray spectra, scanning electron microscope, X-ray fluorescence spectroscopy and for hardness properties. Additionally, the photoluminescence properties were explored by studying excitation and emission spectra. The produced luminescence colourless PMMA plastic substrates displayed excitation band at 370 nm, and three emission peaks at 433, 494 and 513 nm. Photoluminescent PMMA with lower contents of AEA showed fast and reversible photochromism under UV light, while PMMA samples with higher contents of AEA showed long-lasting luminescence such as a flashlight with the ability to replace electric power. The findings showed that the produced photoluminescence colourless PMMA plastic substrates exhibited enhanced UV shielding and superhydrophobicity.

Tuning the Biointerface: Low-Temperature Surface Modification Strategies for Orthopedic Implants to Enhance Osteogenic and Antimicrobial Activity

As both the average life expectancy and incidence of bone tissue reconstruction increases, development of load-bearing implantable materials that simultaneously enhance osseointegration while preventing postoperative infection is crucial. To address this need, significant research efforts have been dedicated to developing surface modification strategies for metallic load-bearing implants and scaffolds. Despite the abundance of strategies reported, many address only one factor, for example, surface chemistry or topography. Furthermore, the incorporation of surface features to increase osteocompatibility can increase the probability of infection, by encouraging the formation of bacterial biofilms. To truly advance this field, research efforts must focus on developing multifunctional coatings that concurrently address these complex and competing requirements. In addition, particular emphasis should be placed on utilizing surface modification processes that are versatile, low cost, and scalable, for ease of translation to mass manufacturing and clinical use. The aim of this short Review is to highlight recent advances in scalable and multifunctional surface modification techniques that obtain a programmed response at the bone tissue/implant interface. Low-temperature approaches based on macromolecule immobilization, electrochemical techniques, and solution processes are discussed. Although the strategies discussed in this Review have not yet been approved for clinical use, they show great promise toward developing the next generation of ultra-long-lasting biomaterials for joint and bone tissue repair.

Conducting Polyetheretherketone Nanocomposites with an Electrophoretically Deposited Bioactive Coating for Bone Tissue Regeneration and Multimodal Therapeutic Applications

The use of polyetheretherketone (PEEK) has grown exponentially in the biomedical field in recent decades because of its outstanding biomechanical properties. However, its lack of bioactivity/osteointegration remains an unresolved issue toward its wide use in orthopedic applications. In this work, graphene nanosheets have been incorporated into PEEK to obtain multifunctional nanocomposites. Because of the formation of an electrical percolation network and the π-π* conjugation between graphene and PEEK, the resulting composites have achieved 12 orders of magnitude enhancement in their electrical conductivity and thereby enabled electrophoretic deposition of a bioactive/antibacterial coating consisting of stearyltrimethylammonium chloride-modified hydroxyapatite. The coated composite implant shows significant boosting of bone marrow mesenchymal stem cell proliferation in vitro. In addition, the strong photothermal conversion effect of the graphene nanofillers has enabled laser-induced heating of our nanocomposite implants, where the temperature of the implant can reach 45 °C in 150 s. The unique multifunctionality of the implant has also been demonstrated for photothermal applications such as enhancing bacterial eradication and tumor cell inhibition, as well as bone tissue regeneration in vivo. The results suggest the strong potential of our multifunctional implant in bone repair applications as well as multimodal therapy of challenging bone diseases such as osteosarcoma and osteomyelitis.

Electrophoretic deposition of polymers and proteins for biomedical applications

This review is focused on new electrophoretic deposition (EPD) mechanisms for deposition biomacromolecules, such as biopolymers, proteins and enzymes. Among the rich literature sources of EPD of biopolymers, proteins and enzymes for biomedical applications we selected papers describing new fundamental deposition mechanisms. Such deposition mechanisms are of critical importance for further development of EPD method and its emerging biomedical applications. Our goal is to emphasize innovative ideas which have enriched colloid and interface science of EPD during recent years. We describe various mechanisms of cathodic and anodic EPD of charged biopolymers. Special attention is focused on in-situ chemical modification of biopolymers and crosslinking techniques. Recent innovations in the development of natural and biocompatible charged surfactants and film forming agents are outlined. Among the important advances in this area are the applications of bile acids and salts for EPD of neutral polymers. Such innovations allowed for the successful EPD of various electrically neutral functional polymers for biomedical applications. Particularly important are biosurfactant-polymer interactions, which facilitate dissolution, dispersion, charging, electrophoretic transport and deposit formation. Recent advances in EPD mechanisms addressed the problem of EPD of proteins and enzymes related to their charge reversal at the electrode surface. Conceptually new methods are described, which are based on the use of biopolymer complexes with metal ions, proteins, enzymes and other biomolecules. This review describes new developments in co-deposition of biomacromolecules and future trends in the development of new EPD mechanisms and strategies for biomedical applications.