Optical characterization of bisphenol-A-glycidyldimethacrylate–triethyleneglycoldimethacrylate (BisGMA/TEGDMA) monomers and copolymer

Bis-EMA/Bis-GMA ratio effects on resin-properties and impregnated fiber-bundles

OBJECTIVES

To evaluate the effect of different ratios of Bis-EMA/Bis-GMA resin mixtures on the inherent viscosity and curing-related properties: including degree of cure (DC%), shrinkage strain, Knoop micro-hardness (KH) and flexural strength of resin-impregnated fiber-bundles.

METHODS

Bis-EMA/Bis-GMA monomers were mixed (by weight) in the following ratios: M1 = 30 %/70 %, M2 = 50 %/50 %, M3 = 70 %/30 %, and M4 = 100 %/0 %. Standard measurements were made of refractive index, viscosity, degree of conversion, shrinkage strain and Knoop hardness (KHN). For 60 % glass fiber-bundles impregnated with 40 % resin, three-point bending test for flexural strength and shrinkage strain were measured. Data were analyzed by One-way ANOVA and Bonferroni post-hoc tests (α = 0.05).

RESULTS

For resin mixtures, increasing Bis-EMA proportion decreased refractive index (p < 0.05), and viscosity (p < 0.05), and increased monomer conversion (DC%), shrinkage strain and KHN (p < 0.05). DC% increased after 1 h for all resin mixtures. The shrinkage strain and flexural strength of resin-impregnated fiber-bundles reduced with increased Bis-EMA.

SIGNIFICANCE

Monomeric mixtures with highest amounts of Bis-EMA showed enhancement in several clinically-relevant properties and polymerization of respective resin-impregnated glass fibers. This makes them potential candidates for impregnating glass fibers in fiber-reinforced restorations.

Assessments of polymerization shrinkage by optical coherence tomography-based digital image correlation analysis-Part I: Parameter identification

OBJECTIVE

To investigate the feasibility of optical coherence tomography (OCT)-based digital image correlation (DIC) analysis and to identify the experimental parameters for measurements of polymerization shrinkage.

METHODS

Class I cavities were prepared on bovine incisors and filled with Filtek Z350XT Flowable (Z350F). One OCT image of the polymerized restoration was processed to generate virtually displaced images. In addition, the tooth specimen was physically moved under OCT scanning. A DIC software analyzed these virtual and physical transformation sets and assessed the effects of subset sizes on accuracy. The refractive index of unpolymerized and polymerized Z350F was measured via OCT images. Finally, different particles (70-80 µm glass beads, 150-212 µm glass beads, and 75-150 µm zirconia powder) were added to Z350F to inspect the analyzing quality.

RESULTS

The analyses revealed a high correlation (>99.99%) for virtual movements within 131 pixels (639 µm) and low errors (<5.21%) within a 10-µm physical movement. A subset size of 51 × 51 pixels demonstrated the convergence of correlation coefficients and calculation time. The refractive index of Z350F did not change significantly after polymerization. Adding glass beads or zirconia particles caused light reflection or shielding in OCT images, whereas blank Z350F produced the best DIC analysis results.

SIGNIFICANCE

The OCT-based DIC analysis with the experimental conditions is feasible in measuring polymerization shrinkage of RBC restorations. The subset size in the DIC analysis should be identified to optimize the analysis conditions and results. Uses of hyper- or hypo-reflective particles is not recommended in this method.

Transmission of radiant light energy through the sides of fiber posts

OBJECTIVES

Resin cements are light polymerized, but the light may not reach all areas of root canals. The purpose of this study was to determine the best predictor of transmitted light radiant exposure (TLRE) from posts' sides.

MATERIALS AND METHODS

Fiber posts were placed in a custom-made apparatus and advanced by 1-mm increments. The LED curing probe tip was activated for 40 s on the coronal end of the post. The TLRE was measured with an LED radiometer detector positioned on the side of the post exposed by an opening in the apparatus. Hierarchical multiple linear regression analysis was performed.

RESULTS

Post system explained an additional 23.62% of the variation in TRLE. Adding actual post diameter explained an additional 62.64% of the variation in TRLE. While adding post length explained an additional 0.67%. Changing post system from FiberKleer to Postec Plus will decrease the mean value of TRLE by 4.90 units on average. Also, a one-unit increase of actual post diameter and length will decrease the value of TRLE by 44.96 and 0.44 units respectively. The TLRE ranged from 46 to 290 mJ/cm² , which was between 0.73% and 6.63% of the original emanating light.

CONCLUSIONS

The changes in post system, posts' diameter and length can be used to predict the unit changes in TLRE on the side of a translucent fiber post. Emanating radiant exposure from the side of the post was lower than 6.63% of the exposure entering the post.

CLINICAL RELEVANCE

Fiber post diameter and length and post system can influence light radiant exposure transmitted from posts' sides, transmitting minimal radiant exposure, which can be increased by increasing curing duration.

Impact of Copper-Doped Mesoporous Bioactive Glass Nanospheres on the Polymerisation Kinetics and Shrinkage Stress of Dental Resin Composites

We embedded copper-doped mesoporous bioactive glass nanospheres (Cu-MBGN) with antibacterial and ion-releasing properties into experimental dental composites and investigated the effect of Cu-MBGN on the polymerisation properties. We prepared seven composites with a BisGMA/TEGDMA (60/40) matrix and 65 wt.% total filler content, added Cu-MBGN or a combination of Cu-MBGN and silanised silica to the silanised barium glass base, and examined nine parameters: light transmittance, degree of conversion (DC), maximum polymerisation rate (R_max), time to reach R_max, linear shrinkage, shrinkage stress (PSS), maximum PSS rate, time to reach maximum PSS rate, and depth of cure. Cu-MBGN without silica accelerated polymerisation, reduced light transmission, and had the highest DC (58.8 ± 0.9%) and R_max (9.8 ± 0.2%/s), but lower shrinkage (3 ± 0.05%) and similar PSS (0.89 ± 0.07 MPa) versus the inert reference (0.83 ± 0.13 MPa). Combined Cu-MBGN and silica slowed the R_max and achieved a similar DC but resulted in higher shrinkage. However, using a combined 5 wt.% Cu-MBGN and silica, the PSS resembled that of the inert reference. The synergistic action of 5 wt.% Cu-MBGN and silanised silica in combination with silanised barium glass resulted in a material with the highest likelihood for dental applications in future.

Influence of Instrument Lubrication on Properties of Dental Composites

Resin composites are one of the most commonly used materials in restorative dentistry. To improve their handling and facilitate restoration sculpting, clinicians began to lubricate modeling instruments with various substances like alcohol, unfilled resins, or even bonding agents. Although the technique is commonly present in daily clinical practice, it has not been precisely described in the literature and both application methods and lubricating materials vary across the available studies. This study aims to summarize the currently available knowledge about influence of instrument lubrication on properties of dental composites. Literature selection was conducted within MEDLINE, SCOPUS, and EBSCO databases. Instrument lubrication seems not to be indifferent for composite mechanical and optical properties. Moreover, various lubricants can differently affect the composite material, so the choice of lubricating agent should be deliberate and cautious. Available in vitro studies suggest possible incorporation of lubricant into the composite structure. Unfilled resins based on bisphenol A-glycidyl methacrylate (Bis-GMA) seem to be the best choice for the lubricant, as bonding agents containing hydrophilic molecules and alcohols carry a bigger risk of altering the composite properties. Further research is necessary to evaluate lubricants' influence in clinical practice conditions.

The effect of refractive index of fillers and polymer matrix on translucency and color matching of dental resin composite

Objective

When restorative resin composites absorb light from the surrounding tooth structures, it creates a color-match, which is known as ‘a chameleon effect’. In this study, series of co-monomer mixtures were prepared with an increasing refraction index (RI) and mixed with glass fillers. The aim of this study was to optimize the mismatch of RI of resin/fillers to create the chameleon effect.

Materials and Methods

BisGMA/TEGDMA resins were prepared with seven different mix fractions from 20 to 80%. Two different series (A&B) of submicron (Ø 0.7 μm) silanized fillers (70 wt%) (A: Schott RI = 1.53, B: Esschem RI = 1.54) were mixed with resins (30 wt%). Disc-shaped specimens (1 mm thickness, Ø10 mm) for each composite combination (n = 3) were prepared and light cured for 20 s. Commercial resin composite (OmniChroma, Tokuyama Dental) was used as control. The translucency parameter (TP) was measured using a spectrophotometer. The color matching abilities of the experimental composites were visually analyzed. Data were statistically analyzed using ANOVA.

Results

The composition of resin and type of fillers had a statistically significant effect on TP values (p < .05). The highest TP values were achieved around 50%-50% fractions of Bis-GMA and TEGDMA for series A and around 60%-40% fraction of Bis-GMA and TEGDMA for series B. Data showed that a high or low fraction of BisGMA resulted in a low translucent composite. Experimental resin composite (80% Bis-GMA) from series A was behaving similarly to Omnichroma in reference to TP values and color matching.

Conclusions

Including fillers with RI of 1.53 into BisGMA/TEGDMA resin with RI of 1.524 resulted in composite resin providing a good color match with surrounding structure ‘chameleon effect’.

Comparative color and surface parameters of current esthetic restorative CAD/CAM materials

PURPOSE

The purpose of this study was to derive and compare the inherent color (hue angle, chroma), translucency (TP_SCI), surface gloss (ΔE^*_SCE-SCI), and surface roughness (R_a) amongst selected shades and brands of three hybrid CAD/CAM blocks [GC Cerasmart (CS); Lava Ultimate (LU); Vita Enamic (VE)].

MATERIALS AND METHODS

The specimens (N = 225) were prepared into square-shaped (12 × 12 mm²) with different thicknesses and shades. The measurements of color, translucency, and surface gloss were performed by a reflection spectrophotometer. The surface roughness and surface topography were assessed by white light interferometry.

RESULTS

Results revealed that hue and chroma values were influenced by the material type, material shade, and material thickness (P < .001). The order of hue angle amongst the materials was LU > CS > VE, whereas the order of chroma was VE > CS > LU. TP_SCI results demonstrated a significant difference in terms of material types and material thicknesses (P ≤ .001). TP_SCI values of the tested materials were ordered as LU > CS > VE. ΔE^*_SCE-SCI and R_a results were significantly varied amongst the materials (P < .001) and amongst the shades (P < .05). The order of ΔE^*_SCE-SCI amongst the materials were as follows LU > VE ≥ CS, whereas the order of R_a was CS ≥ VE > LU.

CONCLUSION

Nano-ceramic and polymer-infiltrated-feldspathic ceramic-network CAD/CAM materials exhibited different optical, inherent color and surface parameters.

Refractive indices of unfilled resin mixtures and cured composites related to color and translucency of conventional and low-shrinkage composites

This study correlated the refractive indices (RIs) of unfilled resin mixtures and resin-based composites (RBCs) with color and translucency of conventional and low-shrinkage RBCs. Unfilled resin mixtures based on different ratios of conventional monomers Bisphenol A-glycidyl-methacrylate (BisGMA)/triethyleneglycol-dimethacrylate (TEGDMA) and urethane-dimethacrylate (UDMA)/TEGDMA and a low-shrinkage monomer FIT-852 (FIT, Esstech Inc.)/TEGDMA were used to prepare model RBCs, containing 30 wt % of the organic matrix and 70 wt % of silanated barium-glass fillers (n = 1.553, Esstech Inc.). The RIs of resins were measured on an ABBE refractometer, those of cured RBCs using the Becke-line method in immersion oils. Color and translucency were determined using an AvaSpec-2048 (Avantes BV) spectrometer. The RIs of unfilled resin mixtures decreased with increasing amounts of TEGDMA. Cured RBCs had higher RIs than their respective resin mixtures. BisGMA-based composites were more translucent with significantly lower L* values than FIT- and UDMA-based RBCs. The RIs of unfilled resins positively correlated with cured RBCs (p = 0.001), as did the RIs with translucency (p = 0.001) and color (p = 0.008). Resin mixtures and corresponding RBCs based on UDMA and its modified low-shrinkage version, FIT, showed similar optical properties. The RIs of unfilled resins appeared to be good predictors of the RIs of cured RBCs. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 7-13, 2017.

Modification of linear prepolymers to tailor heterogeneous network formation through photo-initiated Polymerization-Induced Phase Separation

Polymerization-induced phase separation (PIPS) was studied in ambient photopolymerizations of triethylene glycol dimethacrylate (TEGDMA) modified by poly(methyl methacrylate) (PMMA). The molecular weight of PMMA and the rate of network formation (through incident UV-irradiation) were varied to influence both the promotion of phase separation through increases in overall free energy, as well as the extent to which phase development occurs during polymerization through diffusion prior to network gelation. The overall free energy of the polymerizing system increases with PMMA molecular weight, such that PIPS is promoted thermodynamically at low loading levels (5 wt%) of a higher molecular weight PMMA (120 kDa), while a higher loading level (20 wt%) is needed to induce PIPS with lower PMMA molecular weight (11 kDa), and phase separation was not promoted at any loading level tested of the lowest molecular weight PMMA (1 kDa). Due to these differences in overall free energy, systems modified by PMMA (11 kDa) underwent phase separation via Nucleation and Growth, and systems modified by PMMA (120 kDa), followed the Spinodal Decomposition mechanism. Despite differences in phase structure, all materials form a continuous phase rich in TEGDMA homopolymer. At high irradiation intensity (Io=20mW/cm2), the rate of network formation prohibited significant phase separation, even when thermodynamically preferred. A staged curing approach, which utilizes low intensity irradiation (Io=300µW/cm2) for the first ~50% of reaction to allow phase separation via diffusion, followed by a high intensity flood-cure to achieve a high degree of conversion, was employed to form phase-separated networks with reduced polymerization stress yet equivalent final conversion and modulus.

Curing characteristics of a composite. part 2: the effect of curing configuration on depth and distribution of cure

OBJECTIVE

The objective of this study was to examine the effect different configurations of curing would have on the depth and distribution of the cure within each configuration, for a specific resin-based composite (RBC).

METHODS

RBC was cured in a variety of configurations, consisting of 6mm molds of three different colors; large molds that simulated the condition of no mold at all; and 3-6mm diameter molds to check the effect of size. All specimens were cured for 20s with a quartz-halogen lamp and were allowed to cure for 24h in the dark. Transmission measurements were made for these same configurations. Knoop hardness measurements were made across the central plane of some configurations to determine the distribution of curing.

RESULTS

Depths of cure and distribution of curing were significantly affected by changes in configuration. Under the configuration of no mold, the cure extended well beyond the periphery of the light guide due to scattering of the light. When a mold was used, a pronounced effect by the walls resulted in decreased hardness as the mold wall was approached, and the severity of this effect was dependent on the color of the mold. It is believed that this is due to absorption/reflection characteristics of light by the walls, with the white molds showing the least effect. Reducing the diameter of the molds resulted in significant decreases in depth of cure, which are attributed to light absorption by the walls that limits the penetration of light during the curing procedure.

SIGNIFICANCE

Configuration of curing has a significant effect on the depth of cure, but also significantly reduces the cure near the mold wall. This can have clinical ramifications for the cure along a stainless steel matrix band for Class II restorations, and for test procedures in general, where there is no standardization regarding configuration or where measurements are made on specimens.

The color stability of silorane- and methacrylate-based resin composites

The purpose of this study were to evaluate the discoloration of a silorane-based resin and two methacrylated-based resin composites upon exposure to different staining solutions coffee, red wine, porcine liver esterase and distilled water for 7 days. The colors of all specimens before and after storage in the solutions were measured by a spectrophotometer based on CIE Lab system, and the color differences thereby calculated. Data were statistically analyzed by ANOVA and Scheffe's test. For coffee and red wine, the mean color change in silorane-based resin was significantly lower than that in methacylate-based resin composites (p<0.05). For porcine liver esterase and distilled water, there was no significant difference in the mean values of color change between silorane- and methacrylate-based resin composites (p>0.05). In conclusion, the silorane-based resin composites exhibited better color stability (less ΔE) after exposure to the colored staining solutions.

Effect of cementation technique of individually formed fiber-reinforced composite post on bond strength and microleakage

OBJECTIVES

The aim of this study was to evaluate the effect of two different cementation techniques of individually formed E-glass fiber-reinforced composite (FRC) post on bond strength and microleakage.

METHODS

The crowns of extracted third molars were removed and post preparation was carried out with parapost drills (diameter 1.5 mm). After application of bonding agents individually formed FRC posts (everStick POST, diameter 1.5 mm) were cemented into the post spaces with either ParaCem®Universal or self-adhesive RelyX™Unicem, using two different cementation techniques: 1) an "indirect (traditional) technique" where the post was prepolymerized prior application of luting cement and insertion into the post space or 2) a "direct technique" where the uncured post was inserted to the post space with luting cement and light-polymerized in situ at the same time. After water storage of 48 hours, the roots (n = 10/group) were cut into discs of thickness of 2 mm. A push-out force was applied until specimen fracture or loosening of the post. A microleakage test was carried out on roots which were not subjected to the loading test (n= 32) to evaluate the sealing capacity of the post-canal interface. The microleakage was measured using dye penetration depth under a stereomicroscope.

RESULTS

Higher bond strength values (p<0.05) and less microleakage (p<0.05) were obtained with the "direct technique" compared to the "indirect technique". None of the FRC posts revealed any dye penetration between the post and the cement.

CONCLUSIONS

The "direct technique" seems to be beneficial when cementing individually formed FRC posts.

Influence of a blue DPSS laser on specimen thickness of composite resins

OBJECTIVE

The purpose of the present study was to investigate the effect of 473 nm diode-pumped solid state (DPSS) laser on the curing depth of composite resins.

BACKGROUND DATA

Within the turbid media, light attenuates significantly because of the absorption and scattering.

MATERIALS AND METHODS

For the study, three different composite resins and light-curing units (LCUs) (a quartz-tungsten-halogen [QTH], light-emitting-diode [LED], and DPSS laser) were used. The number of photons transmitted through the specimens, degree of conversion (DC), microhardness, and refractive index of the specimens on different thicknesses were evaluated.

RESULTS

The incident light exponentially decreased within the specimens. Among the LCUs, QTH showed the least photon loss. The DC obtained using the DPSS laser and QTH was significantly greater (p<0.001) than that obtained using LED. The specimens light cured using the DPSS laser showed slightly lower microhardness than that cured by the other LCUs. On each depth, the mean refractive index was not significantly different for the LCUs used. DC, microhardness, and refractive index had inverse linear correlation with specimen thickness despite exponential decrease of photons number. On the other hand, DC, microhardness, and refractive index were linearly correlated to each other regardless of LCUs.

CONCLUSIONS

The DPSS laser of 473 nm achieved a similar level of polymerization within the specimens as those of the other LCUs even with much lower light intensity. This laser can be applied as a light source for light curing of composite resins.

Brillouin spectroscopy studies of two-component polymerizable liquid system: 2,2-bis[4-(2-hydroxymethacryloxypropoxy)phenyl]propane/benzyl methacrylate

Brillouin spectroscopy was used to investigate viscoelastic properties of a two-component system consisting of a high viscosity liquid (HVL) and a low viscosity liquid (LVL), both able to polymerize. The model liquids were: 2,2-bis[4-(2-hydroxymethacryloxypropoxy)phenyl]propane (abbreviated as bis-GMA, HVL) and benzyl methacrylate (BzMA, LVL). The viscosity of the system was regulated by changing the monomer ratio. Hypersonic velocity and attenuation coefficient were investigated in a temperature range covering viscoelastic relaxation process. The dependence of the longitudinal viscosity on the system composition was determined. Additionally, the Brillouin studies were accompanied by some supplementary experimental methods, like low frequency shear viscosity measurements and observations of phase transitions by differential scanning calorimetry (DSC). The investigated monomer mixtures were then polymerized in a light-induced process and the polymerization kinetic curves were measured to find the possible correlation between the viscoelastic properties of the monomer mixture (as observed by Brillouin spectroscopy) and the polymerization course.

Influence of nanometer scale particulate fillers on some properties of microfilled composite resin

The aim of this study was to evaluate the effect of different weight fractions of nanometer sized particulate filler on properties of microfilled composite resin. Composite resin was prepared by mixing 33 wt% of resin matrix to the 67 wt% of silane treated microfine silica particulate fillers with various fractions of nanometer sized fillers (0, 10, 15, 20, 30 wt%) using a high speed mixing machine. Test specimens made of the composites were tested with a three-point bending test with a speed of 1.0 mm/min until fracture. Surface microhardess (Vicker's microhardness) was also determined. The volumetric shrinkage in percent was calculated as a buoyancy change in distilled water by means of the Archimedes principle. The degree of monomer conversion (DC%) of the experimental composites containing different nanofiller fractions was measured using FTIR spectroscopy. Surface roughness (Ra) was determined using a surface profilometer. Nanowear measurements were carried out using a nanoindentation device. The water uptake of specimens was also measured. Parameters were statistically analysed by ANOVA (P < 0.05). The group without nanofillers showed the highest flexural strength and modulus, DC% and Ra value. The group with 30% nanofillers had the highest water uptake and volumetric shrinkage. No significant difference was found in Vicker's microhardness and the nanowear of the composites. The plain microfilled composite demonstrated superior properties compared to the composites loaded with nanofillers with the exception of surface roughness.

Silver-polysaccharide nanocomposite antimicrobial coatings for methacrylic thermosets

Bisphenol A glycidylmethacrylate (BisGMA)/triethyleneglycol dimethacrylate (TEGDMA) thermosets are receiving increasing attention as biomaterials for dental and orthopedic applications; for both these fields, bacterial adhesion to the surface of the implant represents a major issue for the outcome of the surgical procedure. Moreover, the biological behaviour of these materials is influenced by their ability to establish proper interactions between their surface and the eukaryotic cells of the surrounding tissues, which is important for good implant integration. The aim of this work was to develop an antimicrobial non-cytotoxic coating for methacrylic thermosets by means of a nanocomposite material based on a lactose-modified chitosan and antibacterial silver nanoparticles. The coating was characterized by UV-vis spectrophotometry, optical microscopy, transmission electron microscopy (TEM) and scanning electron microscopy (SEM). In vitro tests were employed for a biological characterization of the material: antimicrobial efficacy tests were carried out with both Gram+ and Gram- strains. Osteoblast-like cell-lines, primary human fibroblasts and adipose-derived stem cells, were used for LDH cytotoxicity assays and Alamar blue cell proliferation assays. Cell morphology and distribution were evaluated by SEM and confocal laser scanning microscopy. In vitro results showed that the nanocomposite coating is effective in killing both bacterial strains and that this material does not exert any significant cytotoxic effect towards tested cells, which are able to firmly attach and proliferate on the surface of the coating. Such biocompatible antimicrobial polymeric films containing silver nanoparticles may have good potential for surface modification of medical devices, especially for prosthetic applications in orthopedics and dentistry.

Prepolymerized vs. in situ-polymerized Fiber-reinforced Composite Implants – a Pilot Study

The aim of this study was to investigate bone response to bioactive fiber-reinforced composite (FRC) implants under two polymerization conditions. Glass-fiber-dimethacrylate composite was tested as prepolymerized cylinder-shaped FRC implants and as cylindrical FRC implants polymerized in situ with blue light transmitted and scattered by the glass fibers. Ten FRC implants (6 prepolymerized and 4 in situ-polymerized implants) were placed in the right tibias of 3 pigs by means of a press-fit technique. After 12 weeks, light microscopy revealed only mild foreign-body reaction, with no accumulation of inflammatory cells on both the prepolymerized and the in situ-polymerized implants. The prepolymerized implants appeared to be fully integrated, whereas the in situ-polymerized implants were almost completely surrounded by a fibrous capsule. The present study suggests that in situ polymerization of FRC implants results in fibrous capsule formation and prevents integration with bone.

Color and translucency in silorane-based resin composite compared to universal and nanofilled composites

OBJECTIVES

The purpose of this study was to determine the optical properties, color and translucency, of the new silorane-based resin composite and to compare it to universal dimethacrylate-based composites.

METHODS

Six dimethacrylate-based resin composites and one silorane-based resin composite (all A2 shade) were studied. Color of non-polymerized and polymerized composites was measured against white and black backgrounds using a spectroradiometer. Changes in color (ΔE*(ab)), translucency (ΔTP) and color coordinates (ΔL*, Δa* and Δb*) were calculated for each resin composite. Results were evaluated using a one-way ANOVA, a Tukey's test and a t-test.

RESULTS

The polymerization-dependent ΔE*(ab) ranged from 4.7 to 9.1, with the smallest difference for the silorane-based resin composite. The color changes of silorane-based composite were due to the changes of coordinates Δa* and Δb*. However, for the dimethacrylate-based composites, the color changes mainly originated by ΔL*and Δb*. The silorane composite exhibited the smallest TP values. Tukey's test confirmed significant statistical differences (p<0.05) between mean TP values of Filtek Silorane and each brand of dimethacrylate-based composites before and after polymerization.

CONCLUSIONS

The new silorane-based restorative system showed different optical properties compared to clinically successful dimethacrylate composites. The silorane composite exhibited better polymerization-dependent chromatic stability, and a lower translucency compared to other tested products.