Effect of ozone gas application on the mechanical properties of dental adhesives bonded to dentin

PEEK and glass fiber post pushout bond strength and vickers hardness of canal disinfected with curcumin photosensitizer activated by microbubble emulsion and sodium-hypochlorite with EDTA

AIMS

Impact of different post-space disinfectants (Saline, Sodium hypochlorite (NaOCl) followed by ethylene-diamine-tetra-acetic acid (EDTA) and curcumin activated by microbubble emulsion (MBE) on the Vickers hardness (VH) of root canal dentin and extrusion bond strength (EBS) of Glass fiber post (GFP) and PEEK post.

METHODS

Ninety maxillary central incisors having fully formed roots were included. After the specimen's disinfection, root canal treatment was completed. Post space was prepared by removing gutta-percha using gates glidden drills. Teeth were then arbitrarily allocated into three groups based on the methods of disinfection regime used. Group 1: Saline, Group 2: NaOCl+ EDTA and Group 3: Curcumin activated by MBE (n = 30). Analysis of VH of radicular dentin was performed using a micro-Vickers tester on ten samples from each group. After post-space disinfection, twenty specimens from each group were further divided into two subgroups (n = 10) In group-1A 2A, and 3A, GFP was used. Whereas, prefabricated PEEK posts were used in 1B, 2B, and 3B subgroups. The PBS and failure modes were performed using a universal testing machine and stereomicroscope respectively. Data was analyzed using ANOVA and Tukey post hoc test to identify significant variations among groups concerning the MH and EBS of the different posts used (p = 0.05).

RESULTS

Group 2 (5.25 % NaOCl + 17 % EDTA) (0.15 ± 0.02 GPa) treated specimens presented lowest scores of VH. However, Group 1 (Saline) irrigated canals displayed the highest scores of surface hardness (0.25 ± 0.07 GPa). Additionally, a cervical third of 3A (CP activated by MBE + GFP) (11.22 ± 0.79 MPa) presented the highest scores of bond integrity. Whereas Group 1B (Saline + PEEK post) treated specimens presented the lowest scores of PBS (4.15 ± 0.15 MPa).

CONCLUSION

Curcumin activated by microbubble emulsion for disinfection of canal dentin demonstrated favorable VH. Similarly, glass fiber post-cemented in radicular walls disinfected with curcumin activated with MBE showed promising post-bond integrity to the canal dentin.

The adhesive strength of fiber post-to-canal dentin with Aniline green, Fotoenticine activated by PDT, green tea, and ozone as a final irrigant

AIM

The effect of novel final disinfection protocols Malachite green (MG), Fotoenticine® (FTC), Green tea extract (GTE), and Ozonated water (OW) on the bond strength of prefabricated glass fiber posts (PGFP) adhered to canal dentin.

MATERIAL AND METHOD

The canals of fifty premolars with closed apices were cleansed and obturated. The specimens were randomly assigned to one of five groups based on the final irrigant used, with the control group receiving NaOCl+EDTA and the experimental groups receiving MG, FTC, OW, and GTE. The GFP was cemented with a self-etching, dual-cure paste; the bond strength was estimated with a universal testing machine; and failure analysis was conducted with a stereomicroscope.

RESULTS

The highest PBS was observed in the coronal third of Group 4 (using ozonated water as the final irrigant), whereas the lowest bond integrity was observed in the apical section of Group 2 (1.02-0.54 MPa) using Malachite green as the final irrigant. Group 1, Group 4, and Group 5 exhibited no significant difference in the bond integrity of GFP to dentin when compared to Group 2 (p>0.05). In addition, comparable bond score values were obtained for Groups 2 and 3 (p>0.05).

CONCLUSION

The results of this study suggest that OW and GTE may be effective final disinfectants for root canals, as they increase the bond strength of resin-luting cement.

Effect on Martens Hardness and pushout bond strength of fiber post to canal dentin final irrigated with Fotoenticine, Chitosan, and ozone

AIMS

To estimate the effect of contemporary final root canal irrigants (Ozonated water (OW), Chitosan, and Fotoenticine (FTC) on the bond scores of glass fiber post (GFP) and Martens hardness (MH) of root dentin.

MATERIALS AND METHODS

Sixty extracted human premolars having a single straight canal that ends in a closed apex were included. Specimens were de-crowned till the cementoenamel junction preserving 12 mm of root length and were mounted vertically. Canal therapy was performed using a crown-down approach. Obturation was performed followed by post-space preparation. Samples were allocated into 4 groups based on chemical irrigations and photosensitizers used(n = 15). Group 1 (5.25% NaOCl + 17% EDTA), group 2 (5.25% NaOCl + FTC), group 3 (5.25% NaOCl + Chitosan), group 4 (5.25% NaOCl + OW). The ultra microhardness tester was put under a load of 5 mN at a speed of 1.5 mN/s for 1 s to assess the MH. The fiber post was luted with dual-cure cement and slices of 1 mm were prepared from each third of the tooth. PBS and failure mode analysis were performed using a universal testing machine (UTM) and stereomicroscope respectively. ANOVA and Tukey multiple comparisons t-tests for assessment of PBS and MH p > 0.05 RESULTS: Group 1 (5.25% NaOCl + 17% EDTA) exhibited the highest MH (0.19 ± 0.04 GPa). Whereas, group 2 (5.25% NaOCl + FTC) displayed the lowest MH (0.011 ± 0.14 GPa). The highest PBS was exhibited by the coronal third of group 1 (5.25% NaOCl + 17% EDTA) (7.11 ± 0.81 MPa). The apical section of group 3 specimens (5.25% NaOCl + Chitosan) (2.33 ± 0.26 MPa) unveiled the lowest PBS. Intergroup comparison analysis revealed that group 2 and group 3 displayed comparable outcomes of PBS. Group 1 and Group 4 also demonstrated no significant difference in the bond scores in all three sections.

CONCLUSION

OW as a final irrigant can be used as an alternative to EDTA as it improves the bond strength with minimum impact on marten hardness.

Caries-affected dentin disinfection using Triphala, Indocyanine green, and Potassium Titanyl Phosphate laser and their effect on adhesive bond strength

AIM

To assess the impact of new cavity sterilization types using ozone water (OW), Potassium Titanyl Phosphate laser (KTPL), Triphala, and indocyanine green photosensitizer (ICGP) on adhesive bond strength.

MATERIALS AND METHODS

Fifty human permanent molars were included based on the criteria of International Caries Detection and Assessment System (ICDAS) scores 4 and 5 visual examinations, surface hardness valuation, staining by a caries detector solution, and radiographs. Caries-affected dentin (CAD) samples were randomly distributed into groups based on methods of disinfection (n = 10). Group 1: chlorhexidine, group 2: ow, group 3: KTPL, group 4: Triphala, and group 5: ICGP. Following disinfection, specimens were applied with Adper prime and bond NT and then restored with resin composite. All specimens were positioned in a jig of the universal testing machine for shear bond strength (SBS). The debonded samples were analyzed under a stereomicroscope at 40x magnification to determine the type of failure. Analysis of variance (ANOVA) and Tukey HSD tests were used keeping the level of significance p < 0.05.

RESULTS

The highest bond of adhesive resin was displayed by group 2 specimens cleaned using OW (16.71 ± 0.19 MPa). Whereas, the lowest bond integrity was observed by group 5 specimens disinfected using ICGP (11.21 ± 0.16 MPa). It was observed samples disinfected with OW (16.71 ± 0.19 MPa) in group 2 and samples in group 4 (16.09 ± 0.26 MPa) treated with Triphala displayed comparable outcomes of bond strength (p > 0.05). It was observed that group 2 (70%) and 4 (80%) treated specimens accounted mostly for cohesive failure. However, groups 1 (80%), 3 (60%), and 5 (70%) displayed an adhesive failure pattern.

CONCLUSION

OW and Triphala displayed better bond integrity of adhesive resin to CAD and therefore have the potential to be used as a cavity disinfectant in clinical settings. However, ICGP and KTPL displayed weak bonds of adhesive to CAD. More work is needed to extrapolate the findings of the present study.

Disinfection of caries-affected dentin using potassium titanyl phosphate laser, Rose bengal and Ozonated water on shear bond strength of deciduous teeth

AIM

To assess the efficacy of disinfection of caries-effected dentin (CAD) using KTP laser and different decontamination methods using ozonated water (OW), Rose Bengal photosensitizer (RBP), chlorhexidine (CHX), and Er, YAG laser on the shear bond strength (SBS) of adhesive resin bonded to deciduous teeth.

MATERIAL AND METHODS

A total of 50 extracted and radiographically verified carious primary molars were collected and scrutinized according to ICDAS criteria. Specimens were allocated randomly into five groups (n = 10) as per the type of CAD disinfectants. KTP laser, OW, RBP, CHX (control), and Er, YAG laser. After cavity sanitization, a resin adhesive (prime and bond NT) was smeared on the dentinal exterior followed by incremental composite filling. SBS evaluation was performed by employing specimens in the universal testing machine. The debonded surface was assessed under 40x magnification in a stereomicroscope to ascertain fracture mode. Statistical analysis was done by using the ANOVA and the Post Hoc Tukey multiple comparison tests (p < 0.05).

RESULTS

The highest SBS was exhibited by group 2 i.e., when OW was employed for CAD disinfection (10.25 ± 0.24 MPa). Whereas, the lowest SBS bond value was unveiled by samples in group 3 when RBP was applied for dentin surface sanitization (7.85 ± 0.59 MPa).CAD disinfection with KTP laser (8.25 ± 0.41 MPa), CHX (8.19 ± 0.73 MPa), and RBP displayed comparable bond values (p > 0.05).

CONCLUSION

Ozonated water and Er, YAG laser could be employed as cavity disinfectants in primary teeth as they demonstrated better shear bond strength without jeopardizing the adhesive binding capacity of restorative resins bonded to caries-affected dentin.

The Biological Effects of Ozone Gas on Soft and Hard Dental Tissues and the Impact on Human Gingival Fibroblasts and Gingival Keratinocytes

Ozone is an allotropic form of oxygen, so in the medical field ozone therapy has special effects. Starting from the premise that bio-oxidative ozone therapy reduces the number of bacteria, in the present study two approaches were proposed: to evaluate the biological effects of ozone gas on the tooth enamel remineralization process and to demonstrate its impact on the morphology and confluence of human primary gingival cells, namely keratinocytes (PGK) and fibroblasts (HGF). The ozone produced by HealOzone was applied in vivo to 68 M1s (first permanent molars), both maxillary and mandibular, on the occlusal surfaces at pit and fissure. The molars included in the study recorded values between 13 and 24 according to the DIAGNOdent Pen 2190 scale, this being the main inclusion/exclusion criterion for the investigated molars. Because the gas can make contact with primary gingival cells during the ozonation process, both human gingival fibroblasts and keratinocytes were exposed to different doses of ozone (20 s, 40 s, 60 s), and its effects were observed with the Olympus IX73 inverted microscope. The contact of ozone with the human primary gingival cells demonstrates cell sensitivity to the action of ozone, this being higher in fibroblasts compared to keratinocytes, but it is not considered toxic because all the changes are reversible at 48 h after exposure.

Role of Riboflavin; Curcumin photosensitizers and Ozone when used as canal disinfectant on Push-out bond strength of glass fibre post to radicular dentin

AIM

To assess the efficacy of photosensitizers (CP, riboflavin) and gaseous ozone in comparison to the conventional radicular dentin disinfectant (NaOCl) on push-out bond strength (PBS) of PFRC post cemented to radicular dentin MATERIAL AND METHOD: Human single-rooted teeth were collected, steriled implanted in polyvinyl pipes up to a cement-o-enamel junction and de coronated. Cleaning and shaping of the canal were performed using the crown down technique followed by obturation of the canal space. Canal space was prepared using peso reamers and samples were divided into four groups based on types of canal disinfectant protocols. Group 1: Riboflavin+ 17%EDTA; group 2: Curcumin Photosensitizer + 17% EDTA; group 3: Gaseous Ozone disinfection (O3) +17% EDTA and group 4 control 2.5% NaOCl +17% EDTA. Within the canal space, fiber post was cemented and cured, and thermocycled. PBS was evaluated using a Universal testing machine (UTM) and failure modes using a stereomicroscope at 40x magnification. One-way analysis of variance (ANOVA) was used to determine the mean and standard deviation of push-out bond strength (PBS). The Tukey multiple comparison tests (p = 0.05) was used to compare the means of PBS RESULTS: The highest PBS was displayed in group 2 CP+ 17% EDTA at all three root levels, coronal (8.81±0.61), middle (7.77±0.55), and apical (5.25±0.61). The lowest PBS was revealed in group 4, disinfected with 2.5% NaOCl +17% EDTA (control) at coronal (6.12±0.54), middle (5.46±0.84), and apical (3.00±1.88) levels. The most prevailed fracture mode was an adhesive failure (cement-dentin interface).

CONCLUSION

Radicular dentin disinfected with PDT using CP, riboflavin, and O3 displayed similar PBS at all root segments. NaOCl is a convenient, traditional, and commonly used disinfectant, and it's effects on PBS is still controversial.

The effects of cavity disinfection on the nanoleakage of compomer restorations: an in vitro study

Purpose:

Cavity disinfection, in addition to routine caries removal methods, is recommended to eliminate the microorganisms. The aim of this study was to compare the effect of various systems Er,Cr:YSGG lasers, diode lasers and FotoSan and agents Corsodyl; Cervitec and Cervitec Plus and Fluor Protector—on the nanoleakage of compomer restorations when used for cavity disinfection.

Materials and methods:

A total of 40 intact human deciduous molar teeth containing Black V cavities (3×2×1.5 mm) on the buccal and lingual surfaces parallel to the cementoenamel junction were randomly divided into 8 groups according to the cavity disinfection methods. The antibacterial agents and systems were applied according to the manufacturer’s instructions. Restorations were completed using a compomer. The restored teeth were then subjected to thermocycling for 500 cycles in a water bath at 5°C and 55°C with a dwell time of 30 seconds. After the thermocycling procedures, 1-mm sticks were obtained from the center of each cavity to prepare for the nanoleakage test. After the teeth were sectioned, they were immersed in 50 wt % ammoniacal silver nitrate solution for 24 hours and dipped in photo-developing solutions for 8 hours with fluorescent light irradiation. The samples were examined under a scanning electron microscope (SEM). The non-parametric Kruskal-Wallis and Mann-Whitney U test (p<0.05) were applied.

Results:

The Er,Cr:YSGG laser group showed significantly less nanoleakage than all of the tested groups (p<0.01). The diode laser, Fluor protector and FotoSan groups showed similar nanoleakage to that of the control group (p>0.05). The Corsodyl (p<0.01) and Cervitec (p<0.001) groups showed significantly higher nanoleakage than the control group.

Conclusion:

Er,Cr:YSGG laser irradiation which showed lower nanoleakage scores from either control or tested groups can be recommended for cavity disinfection Additionally, a diode laser and FotoSan, which have antibacterial effects and no negative effect on leakage, can be used for cavity disinfection.

Comparison of ozone gas and sodium hypochlorite/chlorhexidine two-visit disinfection protocols in treating apical periodontitis: a randomized controlled clinical trial

OBJECTIVES

In this single-blinded, prospective, randomized, controlled clinical trial, the effectiveness of an ozone gas or NaOCl/CHX disinfection protocol was compared within the root canal treatment of apical periodontitis.

MATERIALS AND METHODS

Sixty permanent teeth were randomly allocated to one technique. The clinical/radiographic assessment criteria included clinical symptoms, periapical index (PAI), and size of the apical lesion. In both groups, the root canal was mechanically cleaned and irrigated with NaCl and EDTA. Ozone gas (32 g m^-3) or NaOCl (3 %) was applied followed by a 1-week inter-appointment dressing (Ca(OH)₂). As final disinfection, ozone gas (ozone group) or CHX 2 % (NaOCl group) was applied. Microbial samples were taken after preparing the access cavity, after chemo-mechanical treatment and after inter-appointment dressing by sterile paper points. Microbial identification was performed by mass spectroscopy (MALDI-TOF-MS) and 16S-rRNA gene sequencing. The treated teeth were blindly re-evaluated after 6/12 months. Success rates, the decrease in PAI, the size of apical lesions and bacterial reduction were compared between groups (Fischer's exact test, Mann-Whitney U test).

RESULTS

There were no significant differences between the success rates (ozone group: 96.2/95.5 % after 6/12 months; NaOCl group: 95.5/95.2 % after 6/12 months). The differences in the decreases in PAI values and apical lesion sizes were also insignificant after 6 and 12 months. The bacterial reduction showed no significant differences between groups after chemo-mechanical treatment and after inter-appointment dressing. The most commonly found bacterial genera were Streptococcus spp., Parvimonas spp. and Prevotella spp.

CONCLUSIONS

The here used ozone gas and NaOCl/CHX protocols showed no difference in bacterial reduction in the sampled areas of the root canals.

CLINICAL RELEVANCE

Within the limitations of the study, ozone gas seems to be a possible alternative disinfection agent within the root canal treatment of apical periodontitis.

In-vitro comparison of the effect of different bonding strategies on the micro-shear bond strength of a silorane-based composite resin to dentin

Background:

The current study evaluated the micro-shear bond strengths of a new low-shrinkage composite resin to dentin.

Materials and Methods:

In this in-vitro study, 70 extracted premolars were assigned to one of seven groups (n = 10): Group 1: OptiBond Solo Plus (Opt; Kerr); Group 2: SE Bond (SE; Kuraray); Group 3: Silorane System Adhesive (SSA; 3M ESPE); Group 4: OptiBond Solo Plus + LS Bond (Opt LS); Group 5: SE Bond + LS Bond (SE LS); Group 6: OptiBond Solo Plus (Opt Po); and Group 7: SE Bond (SE Po). Occlusal dentin was exposed and restored with Filtek LS (3M ESPE) in groups 1 to 5 and Point 4 (Kerr) in groups 6 and 7. After thermocycling (1000 cycles at 5/55΀C), micro-shear bond test was carried out to measure the bond strengths. The results were submitted to analysis of variance and post hoc Tukeytests (P < 0.05).

Results:

Two-way ANOVA showed no significant differences between the two types of composite resin (P = 0.187), between bonding agents (P = 0.06) and between composite resin and bonding agents (P = 0.894). Because P value of bonding agents was near the significance level, one-way ANOVA was used separately between the two composite groups. This analysis showed significant differences between silorane composite resin groups (P = 0.045) and Tukey test showed a significant difference between Groups 4 and 5 (P = 0.03).

Conclusion:

The application of total-etch and self-etch methacrylate-based adhesives with and without use of a hydrophobic resin coating resulted in acceptable bond strengths.

Effects of ceramic shade and thickness on the micro-mechanical properties of a light-cured resin cement in different shades

OBJECTIVE

The aim of this study was to evaluate the micro-mechanical properties of a light-cured resin cement in four different shades when polymerized through a leucite-reinforced glass-ceramic in different shades and thicknesses.

MATERIALS AND METHODS

A light-cured resin cement in four different shades (HV+1, HV+3, LV-1 and LV-3) was selected for this study. The specimens were cured by using a LED-unit (Bluephase®, IvoclarVivadent) for 20 s under a leucite-reinforced glass-ceramic (IPS Empress® CAD, IvoclarVivadent) in two different shades (A1 and A3) of different thicknesses (1 and 2 mm). Specimens cured directly, without an intermediate ceramic, served as control. The specimens were stored after curing for 24 h at 37°C by maintaining moisture conditions with distilled water. Micro-mechanical properties (indentation modulus, E; Hardness, HV; creep, Cr) of the resin cements were measured with an automatic microhardness indenter (Fisherscope H100C, Germany). Twenty groups were included (n = 3), while 10 measurements were performed on each specimen. Data were statistically analyzed by using one-way ANOVA and Tukey's post-hoc test, as well as a multivariate analysis to test the influence of the study parameters.

RESULTS

Significant differences were observed between the micromechanical properties of the tested resin cements (p < 0.05). The resin cement shade showed the highest effect on the micromechanical properties (Partial-eta squared (ηP(2))-E = 0.45, ηP(2)-HV = 0.59, ηP(2)-Cr = 0.29) of the resin cement, followed by ceramic thickness (ηP(2)-E = 0.38, ηP(2)-HV = 0.3, ηP(2)-Cr = 0.04) and ceramic shade (ηP(2)-E = 0.2, ηP(2)-HV = 0.26).

CONCLUSIONS

Resin cement shade is an important factor influencing the mechanical properties of the material. Light shades of a resin cement express higher E and HV as well as lower Cr values compared with the darker ones.

Influence of ceramic thickness and type on micromechanical properties of light-cured adhesive bonding agents

OBJECTIVE

The aim of this study was to evaluate the micromechanical properties of different adhesive bonding agents when polymerized through ceramics.

MATERIALS AND METHODS

Sixty sound extracted human third molars were selected and the crowns were sectioned perpendicular to the long axis in order to obtain dentin slices to be bonded with one of the following adhesives: Syntac/Heliobond (Ivoclar-Vivadent) or Adper-Scotchbond-1XT (3M-ESPE). The adhesives were cured by using a LED-unit (Bluephase®, Ivoclar Vivadent) with three different curing times (10 s, 20 s and 30 s) under two ceramics (IPS-e.max-Press, Ivoclar-Vivadent; IPS-Empress®CAD, Ivoclar-Vivadent) of different thicknesses (0 mm, 0.75 mm, 2 mm). Thirty groups were included, each containing 60 measurements. Micromechanical properties (Hardness, HV; indentation modulus, E; and creep, Cr) of the adhesives were measured with an automatic microhardness indenter (Fisherscope H100C, Germany). Data were statistically analyzed by using one-way ANOVA and Tukey's post-hoc test, as well as a multivariate analysis to test the influence of the study parameters (SPSS 18.0).

RESULTS

Significant differences were observed between the micromechanical properties of the adhesives (p < 0.05). The ceramic type showed the highest effect on HV (Partial-eta squared (η(2)) = 0.109) of the tested adhesives, while E (η(2) = 0.275) and Cr (η(2) = 0.194) were stronger influenced by the adhesive type. Ceramic thickness showed no effect on the E and Cr of the adhesives.

CONCLUSIONS

The adhesive bonding agents used in this study performed well by curing through different thicknesses of ceramics. The micromechanical properties of the adhesives were determined by the adhesive type and were less influenced by ceramic type and curing time.

Ozone therapy in the management and prevention of caries

The purpose of this article was to assess the effectiveness of ozone therapy in the management and prevention of caries, reviewing clinical and in vitro studies. Ozone has proven to be effective against gram-negative and gram-positive bacteria, viruses, and fungi. In dentistry, most of the published articles are based on ozone's antimicrobial effects and the treatment of caries. Most of the clinical studies reported ozone to be a promising alternative to conventional methods for caries management. However, a few studies have shown ozone to be insufficient for preventing caries and reducing microorganisms in open occlusal carious lesions. Ozone might be a useful tool to reduce and control oral infectious microorganisms in dental plaque and dental cavity. However, the results of in vitro studies are controversial; while some researchers reported that ozone therapy had a minimal or no effect on the viability of microorganisms, others suggested ozone to be highly effective in killing both gram-positive and gram-negative oral microorganisms. Therefore, more evidence is required before ozone can be accepted as an alternative to present methods for the management and prevention of caries.

Influence of activated bleaching on various adhesive restorative systems

STATEMENT OF THE PROBLEM

  When adhesive restorations are used in combination with bleaching in clinical applications, it is generally recommended to wait for a period of time between the two procedures. However, it is not clear if a time interval is necessary between applying the bleaching treatments and the silorane-based restorative system.

PURPOSE

  The purpose of this in vitro study was to determine if activated bleaching affects the bond strength of silorane-based restorative, a newly developed restorative that uses a polymerization system that has been reported to be insensitive to oxygen.

METHODS

  A gel consisting of 38% hydrogen peroxide was applied to ground labial enamel surfaces and activated using a diode laser to bleach the teeth. Then, without waiting for any period of time, four different restorative materials were applied to the bleached enamel surfaces, and these sets were compared with nonbleached control samples. The shear bond strength of the restorative systems to enamel was tested, and data was evaluated using two-way analysis of variance and Tukey HSD tests.

RESULTS

  Significant differences (p<0.05) in shear bond strengths were found among bleached and nonbleached enamel surfaces.

CONCLUSION

  It may be more beneficial to allow a time interval of 2 to 3 weeks between activated hydrogen peroxide bleaching and applying silorane-based composite restoratives or methacrylate-based composites than just applying restorative agents immediately after bleaching. However, further studies are needed to examine the structural effects of activated hydrogen peroxide on enamel.

CLINICAL SIGNIFICANCE

A time interval should be allowed between the application of silorane-based or methacrylate-based restorations and activated hydrogen peroxide bleaching systems.

Effect of different disinfectant methods on the initial microtensile bond strength of a self-etch adhesive to dentin

The aim of this in vitro study was to evaluate the effect of different disinfection methods on the initial microtensile bond strength of a two-step, self-etch adhesive to dentin. Twenty mandibular molars were sectioned parallel to the occlusal plane to expose the mid-coronal dentin. All of the teeth were divided into four groups (n = 5 per group): (1) in group OZ, the dentin surfaces were exposed to ozone gas from the Ozonytron X delivery system (OzonyTron X-Bioozonix, Munich, Germany), (2) in group ND, the dentin surfaces were irradiated with an Nd:YAG laser (Pulsmaster 600 IQ, American Dental Technologies, U.S.), (3) in group CHX, the dentin surfaces were treated with a 2% chlorhexidine solution, and (4) in the control group, no treatment was applied. In all of the groups, the teeth were restored with Clearfil SE Bond (Kuraray, Tokyo, Japan) and Clearfil Majesty Posterior (Kuraray, Tokyo, Japan), according to the manufacturer's instructions. The teeth were sectioned perpendicular to the bonded surface (surface area of approximately 1 mm(2)). Thus, six to seven specimens were obtained from each tooth, and a total of 34 specimens were analyzed in each group. The specimens were attached to the microtensile test machine (Micro Tensile Tester, T-61010 K, Bisco, U.S.). The data was analyzed using the one-way analysis of variance (ANOVA) and Tukey test (p < 0.05). Fracture modes of each specimen were determined using a stereomicroscope (SZ-PT Olympus, Tokyo, Japan) and a scanning electron microscope (SEM). The lowest bond strength occurred in the OZ group. Significant differences were determined only between group OZ and the other groups (group ND, group CHX, and control group) (p < 0.05). In conclusion, although ozone decreased the microtensile bond strength of the self-etch adhesive system to dentin, the Nd:YAG laser and 2% chlorhexidine did not change the microtensile bond strength so in context of the present study it would appear that the Nd:YAG laser and 2% chlorhexidine may be used as pre-restorative sterilization procedures on the dentin prior to the application of a two-step, self-etch adhesive.

Effect of ozone application on the resin-dentin microtensile bond strength

When ozone is used during caries treatment, bond strength can be compromised by the release of oxygen. The use of antioxidant agents neutralizes the free oxygen. The aim of this study was to evaluate the effects of ozone and sodium ascorbate on resin-dentin microtensile bond strength (μTBS). Forty human third molars were divided into four groups: Group 1, not treated with ozone; Group 2, ozone application followed by acid etching; Group 3, acid etching followed by ozone application; and Group 4, ozone and application of sodium ascorbate. Bonded beams (1.0 mm(2)) were tested under tension (0.5 mm min(-1)). The μTBS values were analyzed using one-way analysis of variance (ANOVA) and the Tukey test (p=0.05). All beams that fractured were analyzed under stereomicroscopy (40×). Group 1 had significantly higher μTBS values than Group 2 or 3. The μTBS values of Groups 1 and 4 were similar and higher than those of Group 2. The use of ozone in Group 2 resulted in lower values of μTBS in all conditions evaluated. The predominant failure mode was adhesive. The application of ozone decreased the μTBS of the dentin-composite resin interface. These values were reversed when compared with Groups 1 and 2 when sodium ascorbate was used.

Effects of different cavity disinfectants on shear bond strength of a silorane-based resin composite

AIM

This in vitro study evaluated the effect of different cavity disinfection agents on bond strength of a silorane-based resin composite.

MATERIALS AND METHODS

Thirty-six caries-free human third mandibular molars sectioned in mesio-distal direction were mounted in acrylic resin with their flat dentin surfaces exposed. After the dentin surfaces were wet ground with # 600 silicon carbide paper, the teeth were randomly divided into 6 groups of 12 each according to the cavity disinfection agents; chlorhexidine (CHX); sodium hypochlorite (NaOCl), propolis, ozone, Er,Cr:YSGG laser and no treatment (control). After treatment of dentin surfaces with one of these cavity disinfection agents, Filtek Silorane adhesive system was applied. The silorane-based resin composite, Filtek Silorane was condensed into a mold and polymerized. After storage at 37°C for 24 hours, the specimens were tested in shear mode at a crosshead speed of 1.0 mm/minute. The results were analyzed by one-way ANOVA.

RESULTS

No statistically significant difference was observed between the groups (p>0.05).

CONCLUSION

The use of the tested cavity disinfection agents, chlorhexidine, sodium hypochlorite, propolis, ozone and Er,Cr:YSGG laser did not significantly affect the dentin bond strength of a silorane-based resin composite, filtek supreme.

CLINICAL SIGNIFICANCE

Cavity disinfectant applications did not affect the dentin bond strength of a silorane-based resin composite.

The antibacterial effect of gas ozone after 2 months of in vitro evaluation

The aim of this study was to evaluate the effect of HealOzone on two microorganisms, 4 and 8 weeks after treatment, using a tooth cavity model. Four groups of caries-free third molars (n = 12) were used (A, B, C and D). Three cavities were prepared into each tooth. After sterilization, groups A and B were inoculated with Streptococcus mutans, and groups C and D, with Lactobacillus casei for 48 h. One cavity of each tooth was used to evaluate the infection. After inoculation, groups B and D were treated with ozone (60 s), and groups A and C were used as controls. Then, the two cavities of each tooth were filled with composite, and the teeth were stored in sucrose medium. The restorations were removed after 4 and 8 weeks, respectively; dentin chips were collected, and the amount of microorganisms was determined. Ozone treatment reduced significantly the amount of S. mutans compared to the control group (p ≤ 0.05). This antibacterial effect was able to be seen after 4 (p = 0.0005) and 8 (p = 0.0002) weeks. No significant difference was found between the control and treated group as far as L. casei is concerned (p > 0.05). HealOzone (60 s) can provide some antibacterial treatment against S. mutans even after 8 weeks. However, an elimination of the microorganisms through HealOzone seems not to be possible. L. casei was more resistant to ozone. Although ozone exerts a significant antibacterial effect against S. mutans, it is probably not enough as the only antibacterial method, during the fillings therapy.

Effects of ozone and ND:YAG laser pretreatment on bond strength of self-etch adhesives to coronal and root dentin

OBJECTIVES

The aim of this study was to evaluate the effects of two different disinfection treatments--ozone and Nd:YAG laser application--on shear-bond strength (SBS) of self-etch adhesives to coronal and root dentin.

MATERIALS AND METHODS

Sixty extracted human canines were ground flat, exposing the coronal and root dentin surfaces, and randomly divided into three groups. The surfaces were untreated (Control) or treated with ozone (HealOzone, KaVo) or Nd:YAG laser (Fidelis III, Fotona). Coronal and root dentins of 10 teeth of each group were treated with a two-step self-etch adhesive (Clearfil SE Bond, Kuraray Medical; SE), whereas the remaining 10 teeth were treated with a one-step self-etch adhesive (Clearfil Tri-S Bond, Kuraray Medical; S3). A resin composite (Clearfil Majesty Esthetics, Kuraray Medical) was then placed, and SBS was tested with a universal testing machine. Failure modes were determined under a stereomicroscope. The mean SBS values of each group were calculated, and data were subjected to statistical analysis (p = 0.05).

RESULTS

For the coronal dentin, Control/SE showed significantly higher values than Control/S3, Ozone/S3, and Nd:YAG/S3. Although Ozone/SE showed significantly higher values than Nd:YAG/S3 (p < 0.05), the differences within the other groups were not significant for the root dentin (p > 0.05). Comparison of two dentin substrates in each group did not show any significant difference except for Control/SE, in which coronal dentin showed higher SBS. The failure modes of all groups were mainly adhesive.

CONCLUSION

Pretreatments with Ozone or Nd:YAG laser did not impair the SBS of both of the self-etch adhesives used to coronal and root dentin.

Influence of ozone on the composite-to-composite bond

The study evaluated the effect of ozone application on the composite-to-composite bond. Three hundred and twenty cylindrical composite specimens were divided into two groups: group 1 was subjected to a 60 s ozone application, whereas group 2 remained untreated. Four subgroups were obtained from each group according to the intermediate repair agent: an adhesive, a silane, silane/adhesive combination, or flowable composite. Repair composite cylinders were built-up. The composite repair strength was tested after 24 h and after thermocycling with a shear test. Additionally, 4 mm × 4 mm × 2 mm composite specimens were prepared and stored 24 h in deionized water. Half of the specimens were subjected to ozone application and the other served as control. The elastic modulus (E) and the Vicker's hardness (VH) of the composite surfaces were tested immediately and after thermocycling. Significant differences among the experimental groups were detected (p < 0.001). The composite repair strength was affected by the pretreatment and by the intermediate agent, whereas, the thermocycling was not significant. The partial eta-squared statistics showed that the intermediate agent was the main factor affecting the composite repair strength, whereas the pretreatment played a minor role. No differences were observed between ozone and control groups when the same intermediate agent and the same aging conditions were applied. Repairing with flowable composite tended to achieve higher bond strengths (20.7 and 26.5 MPa in ozone and control groups, respectively, after 24 h). The use of silane coupling agent showed the lowest composite repair strengths. Ozone did not affect E and VH (p > 0.05) and the thermocycling affected only E (p < 0.05). In conclusion, the application of ozone does not impair the composite-to-composite bond.