Physicochemical and mechanical characterization of a fiber-reinforced composite used as frameworks of implant-supported prostheses

Intra-radicular retention with custom designed CAD-CAM fibRe-reinforced composite post-core: a dental technique

A technique is outlined for utilising a polymeric composite reinforced with glass fibres in a three-dimensional mesh as a post-core in aesthetic cases. The clinical procedure involves obtaining an impression of the root canal space, scanning the definitive cast, and milling a fibre-reinforced composite post-core. Subsequently, the intra-radicular post-core is cemented using an adhesive resin cement. The use of custom-made computer-aided design-computer-aided manufacturing (CAD-CAM) fibre-reinforced composite post-core facilitates repairability, provides better adaptation to the root canal space, avoids uneven cement thickness, ensures chemical adhesion to resin cement, and promotes favourable aesthetics when combined with all-ceramic crowns.

'Thermo-mechanical behavior of alternative material combinations for full-arch implant-supported hybrid prostheses with short cantilevers'

OBJECTIVES

To compare the fracture resistance (FR) of three combinations of materials for full-arch maxillary implant-supported hybrid prostheses (HPs) with short cantilevers (≤ 10 mm).

METHODS

Maxillary HPs were fabricated and classified as follows (n = 5 each): Group-1 (CC-A, control): acrylic-resin-veneered Co-Cr frameworks; Group-2 (CF-A): acrylic-resin-veneered carbon-fiber mesostructures; and Group-3 (CF-R): composite-resin-veneered carbon-fiber frames. Specimens were thermal-cycled (5,000 cycles; 5 °C-55 °C; dwell time: 30 s). Vertical loads were applied until failure, first at the 10-mm-long cantilever (LC), and, afterwards, at the anterior region (AR), using a universal testing machine (crosshead speed: 0.05 mm/s). The fracture pattern was assessed by stereomicroscope and SEM. The one-way ANOVA, the Bonferroni, and the independent samples t tests, were run (α= 0.05).

RESULTS

At LC, CF-A, and CC-A samples exhibited the highest FR values (p< 0.001), showing no differences to each other. At AR, CC-A specimens recorded the highest FR, followed by CF-A samples (p< 0.001). CF-R HPs displayed the lowest FR at both locations (p< 0.001). The only group with differences between the tested sites was the CC-A, the AR being more resistant (p< 0.001). Most CC-A and CF-A HPs failed cohesively. CF-R prostheses mainly failed adhesively.

CONCLUSIONS

Maxillary HPs with short cantilevers (≤ 10 mm) made of Co-Cr or carbon-fiber veneered with acrylic resin demonstrated an adequate mechanical resistance (> 900 N).

CLINICAL SIGNIFICANCE

For maxillary HPs with cantilevers up to 10 mm, acrylic-veneered carbon- fiber mesostructures may be recommended, whereas coating carbon-fiber frames with composite resin seems not suitable.

Discoloration of fiber-reinforced composite resin disc for computer-aided design/computer-aided manufacturing after immersion in coffee and curry solutions

The purpose of this study was to clarify the discoloration of fiber-reinforced composite resin (FRC) disc materials. The color differences (ΔEs) of three CAD/CAM disc materials, FRC with different fiber orientations, composite resin, and polyether-ether-ketones were evaluated after month-long immersion in water, coffee, and curry. The ΔEs of all materials after coffee and curry immersion increased with increasing immersion periods, while those after water immersion barely increased. FRC exhibited a smaller color difference and water sorption value than composite resin and a greater color difference and water sorption value than polyether-ether-ketones. The ΔEs after coffee immersion were significantly correlated with the water sorption value. The ΔE of FRC with fiber orientations perpendicular to the surface was greater than that of FRC with fiber orientations parallel to the surface, likely due to greater exposure of the matrix-fiber interface. This result suggested that the fiber orientations of FRC affected the discoloration.

Indirect restorative systems-A narrative review

OBJECTIVE

The background and clinical understanding of the properties of currently available indirect restorative systems and fabrication methods is, along with manufacturer and evidence-based literature, an important starting point to guide the clinical selection of materials for tooth and/or implant supported reconstructions. Therefore, this review explores most indirect restorative systems available in the market, especially all-ceramic, along with aspects of manufacturing process, clinical survival rates, and esthetic outcomes.

OVERVIEW

Progressive incorporation of new technologies in the dental field and advancements in materials science have enabled the development/improvement of indirect restorative systems and treatment concepts in oral rehabilitation, resulting in reliable and predictable workflows and successful esthetic and functional outcomes. Indirect restorative systems have evolved from metal ceramics and polymers to glass ceramics, polycrystalline ceramics, and resin-matrix ceramics, aiming to improve not only biological and mechanical properties, but especially the optical properties and esthetic quality of the reconstructions, in attempt to mimic natural teeth.

CONCLUSIONS

Based on several clinical research, materials, and patient-related parameters, a decision tree for the selection of indirect restorative materials was suggested to guide clinicians in the rehabilitation process.

CLINICAL SIGNIFICANCE

The pace of materials development is faster than that of clinical research aimed to support their use. Since no single material provides an ideal solution to every case, professionals must continuously seek information from well designed, long-term clinical trials in order to incorporate or not new materials and technological advancements.

Probability of survival and failure mode of endodontically treated incisors without ferrule restored with CAD/CAM fiber-reinforced composite (FRC) post-cores

PURPOSE

This study evaluated the probability of survival and failure mode of endodontically treated incisors without ferrule restored with CAD/CAM FRC post-cores.

METHODS

Root canals of bovine incisors were treated, leaving post preparations of ∼10 mm. Teeth were allocated into three groups: (i) cast metal post-core, (ii) FRC prefabricated post with a direct resin core build-up, and (iii) CAD/CAM FRC post-core. Posts and zirconia crowns were cemented using resin cement. Specimens were subjected to step-stress accelerated-life fatigue testing in water. Use level probability Weibull curves, probability of survival for a mission of 100,000 cycles at 25, 50, and 100 N, Weibull modulus, and characteristic strength were calculated and plotted. Failure mode was examined under a stereomicroscope.

RESULTS

Restored incisors demonstrated high probability of survival (93-100%) for missions estimated at 25 and 50 N, irrespective of post-core foundation. At 100 N, incisors restored with metal posts presented significantly higher probability of survival (99%) relative to CAD/CAM posts (79%), whereas FRC groups demonstrated no significant difference. Weibull analysis indicated no significant difference on the Weibull modulus (m = 3.38-5.92). Incisors reconstructed with metal post-cores (431 N) presented significantly higher characteristic strength relative to prefabricated (200 N) and CAD/CAM (202 N) FRC post-cores. While post fracture was the chief failure mode for prefabricated and CAD/CAM FRC post-cores, post and/or root fracture were the main event for metal post-cores.

CONCLUSION

Endodontically treated incisors without ferrule restored with CAD/CAM FRC post-cores presented promising probability of survival for loads compatible with anterior masticatory forces and favorable failure modes.

Comparison of marginal and internal adaptation of three-unit fixed dental prostheses made using CAD/CAM metal-free materials

The aim of this study was to compare the marginal and internal adaptation of three-unit fixed dental prostheses (FDPs) fabricated from different metal-free materials using CAD/CAM methods. A total of 100 three-unit FDPs were produced from a cubic zirconia, a fiber-reinforced resin composite, a polyetheretherketone (PEEK), a polyetherketoneketone (PEKK), and a polymer composite material by the CAD/CAM method (n = 20 per material). The zirconia group was considered the control/reference material. Marginal and internal gap values of the produced FDPs were measured using the silicone replica method at ×40 magnification under a stereomicroscope. The obtained data were analyzed using one-way ANOVA and Tukey's HSD tests. The marginal and internal gap values for the cubic zirconia material were found to be statistically significantly lower than those seen for the PEEK, polymer composite, PEKK, and fiber-reinforced resin composite materials. While the marginal and internal adaptation of the cubic zirconia material was found to be better than the others, it should be noted that the marginal and internal gap values for all other materials tested were found to be within the clinically acceptable range.

Glass fiber-reinforced composites in dentistry

Background

Enormous improvements in dental materials’ manufacturing for the aim of producing durable dental materials without compromising the aesthetic properties were developed. One of the approaches that fulfill this aim is the use of reinforcing glass fibers as fillers into dental materials, typically resin polymers, in order to obtain glass fiber-reinforced composites. Glass fiber-reinforced composite offered many advantages to the dental materials though some limitations were recorded in many literature.

Methods

In this review, a study of the glass fibers’ types, factors affecting the properties and the properties of glass fibers reinforced materials was carried out; in addition, research papers that experimentally studied their applications in dentistry were presented.

Conclusion

The success of glass fibers reinforced composites in dentistry depends on glass fibers’ composition, orientation, distribution, amount, length and adhesion; these factors once employed according to the required clinical situation would provide the essential reinforcement to the dental restorations and appliances.