Heterogeneous sonocatalytic degradation of an anionic dye in aqueous solution using a magnetic lanthanum dioxide carbonate-doped zinc ferrite-reduced graphene oxide nanostructure

Ultrasonic treatment of dye chemicals in wastewater: A review

The existence of pollutants, such as toxic organic dye chemicals, in water and wastewater raises concerns as they are inadequately eliminated through conventional water and wastewater treatment methods, including physicochemical and biological processes. Ultrasonic treatment has emerged as an advanced treatment process that has been widely applied to the decomposition of recalcitrant organic contaminants. Ultrasonic treatment has several advantages, including easy operation, sustainability, non-secondary pollutant production, and saving energy. This review examines the elimination of dye chemicals and categorizes them into cationic and anionic dyes based on the existing literature. The objectives include (i) analyzing the primary factors (water quality and ultrasonic conditions) that influence the sonodegradation of dye chemicals and their byproducts during ultrasonication, (ii) assessing the impact of the different sonocatalysts and combined systems (with ozone and ultraviolet) on sonodegradation, and (iii) exploring the characteristics-based removal mechanisms of dyes. In addition, this review proposes areas for future research on ultrasonic treatment of dye chemicals in water and wastewater.

Enhancement of photocatalytic activities of ZnFe2O4 composite by incorporating halloysite nanotubes for effective elimination of aqueous organic pollutants

ZnFe₂O₄ is a highly desirable catalyst due to its exceptional photo-response in the visible light region, but various drawbacks, such as rapid recombination of photo-generated electron-hole pairs and severe particle agglomeration, make it difficult to use. In this study, a co-precipitation approach was used to create ZnFe₂O₄/HNT (ZF/HNTs) composites. XRD, SEM, TEM, FTIR, BET, and DRS were used to characterize the ZF/HNT composites. Furthermore, the effectiveness of removing crystal violet under simulated visible light irradiation was used to assess photocatalytic activity. The results showed that ZnFe₂O₄ with typical diameters of around 20 nm was significantly distributed on halloysite nanotubes. Because of the synergistic impact of the improved agglomeration phenomena of ZnFe₂O₄ and the decreased recombination rate of photo-generated electrons and holes, all of the composites had superior photocatalytic performance than pure ZnFe₂O₄. The ZF/HNTs-11 composite exhibited the highest removal performance, removing 96.7% of the sample in less than 150 min. In addition, the composite was very stable and reusable. Consequently, ZF/HNTs-11 composite is an effective catalyst for treating pollutants found in wastewater.

A Facile Fabrication of ZnFe2O4/Sepiolite Composite with Excellent Photocatalytic Performance on the Removal of Tetracycline Hydrochloride

The excellent photo-response of ZnFe2O4 in the visible light region makes it a promising catalyst, whereas some defects like serious particle agglomeration and easy recombination of photo-generated electron-hole pairs hinder its application. In this work, the ZnFe2O4/sepiolite (ZF-Sep) composites were synthesized using a co-precipitation method. The obtained ZF-Sep composites were characterized by XRD, SEM, TEM, FT-IR, XPS, BET, VSM and DRS. Moreover, the photocatalytic performance was evaluated by the tetracycline hydrochloride removal efficiency under simulated visible light illumination. The results displayed that the ZnFe2O4 with average sizes about 20 nm were highly dispersed on sepiolite nanofibers. All the composites exhibited better photocatalytic performance than pure ZnFe2O4 due to the synergistic effect of the improvement on the agglomeration phenomenon of ZnFe2O4 and the reduction on the recombination rate of photo-generated electrons and holes. The optimum removal efficiency was that of the ZF-Sep-11 composite, which reached 93.6% within 3 h. Besides, the composite exhibited an excellent stability and reusability. Therefore, ZF-Sep composite is a promising catalyst for the treatment of wastewater contained antibiotics.

Review of MXene-based nanocomposites for photocatalysis

Since multilayered MXenes (Ti₃C₂T_x, a new family of two-dimensional materials) were initially introduced by researchers at Drexel University in 2011, various MXene-based nanocomposites have received increased attention as photocatalysts owing to their exceptional properties (e.g., rich surface chemistry, adjustable bandgap structures, high electrical conductivity, hydrophilicity, thermal stability, and large specific surface area). Therefore, we present a comprehensive review of recent studies on fabrication methods for MXene-based photocatalysts and photocatalytic performance for contaminant degradation, CO₂ reduction, H₂ evolution, and N₂ fixation with various MXene-based nanocomposites. In addition, this review briefly discusses the stability of MXene-based nanophotocatalysts, current limitations, and future research needs, along with the various corresponding challenges, in an effort to reveal the unique properties of MXene-based nanocomposites.

Fabrication of black TiO2-x /NiFe2O4 supported on diatomaceous earth with enhanced sonocatalytic activity for ibuprofen mitigation

This study reports a facile fabrication of black TiO_2-x /NiFe₂O₄ (Ti³⁺ self-doped titania coupled with nickel ferrite), an efficient sonocatalyst for ibuprofen (IBP) mitigation. Compared with TiO_2-x or NiFe₂O₄, TiO_2-x /NiFe₂O₄ heterojunction displayed higher sonocatalytic activity, and their immobilization onto diatomaceous earth further enhanced mitigation efficiency due to the synergy between adsorption and sonocatalysis. About 96.7% of 10 mg l^-1 IBP was removed in 100 min using 0.7 g l^-1 catalyst at pH = 6, with the ultrasonic power of 144 W and frequency of 60 KHz. Quenching experiment results demonstrated the roles of reactive species. The intermediates during IBP sono-oxidation were determined by HPLC-MS method, and the acute toxicity was evaluated. Furthermore, the reaction mechanism was proposed. The sonocatalyst revealed excellent reusability, suggesting itself promising for wastewater treatment.

Novel Z-scheme Ag3PO4/Fe3O4-activated biochar photocatalyst with enhanced visible-light catalytic performance toward degradation of bisphenol A

A novel solid-state Z-scheme heterostructure, Ag₃PO₄/Fe₃O₄ co-doped bamboo-derived activated biochar (Ag-Fe@BAB), was synthesized as an efficient photocatalyst via a co-precipitation method. Ag-Fe@BAB was used as a magnetically recoverable photocatalyst to generate free radical species with peroxydisulfate (PDS) activation under visible-LED-light illumination. The successful synthesis of Ag-Fe@BAB was confirmed by various characterization techniques. Bisphenol A (BPA) was used as a model pollutant to evaluate the photocatalytic activities of the Vis/Ag-Fe@BAB/PDS system. To confirm the photocatalytic performance of the Vis/Ag-Fe@BAB/PDS system, the effects of significant operating parameters such as the contact time, concentration of oxidant, photocatalyst dosage, and solution pH on the degradation of BPA were evaluated. We confirmed that 95.6% BPA was degraded within 60 min in the Vis/Ag-Fe@BAB/PDS system under 1.0 g/L photocatalyst, pH 6.5, and 0.5 mM PDS. The degradation mechanism of BPA in the Vis/Ag-Fe@BAB/PDS system was mainly attributed to O₂^‾ owing to its photocatalytic performances in the presence of p-benzoquinone as a scavenger. Furthermore, the radical species produced in the Vis/Ag-Fe@BAB/PDS system were identified by electron spin resonance. Finally, we demonstrated the recyclability of the Ag-Fe@BAB photocatalyst through its excellent magnetic property.

Visible light activated magnetic photocatalysts for water treatment

Environmental concerns have been raised regarding the intense contamination of water resources. Currently, numerous contaminants that reach water bodies are not efficiently removed by conventional water treatment methods. Therefore, there arises the need for development and optimization of efficient treatment methods for the removal of such recalcitrant contaminants. Given the circumstances, the present study aims to use of advanced oxidative processes for dye degradation. For this purpose, copper and zinc doped cobalt ferrites were synthesized by coprecipitation, targeting the degradation of methylene blue dye. The photocatalysts were characterized by XRD, WD-XRF, FE-SEM, N₂ physisorption isotherms, UV-Vis diffuse reflectance spectroscopy, molecular fluorescence spectroscopy and zeta potential. According to the investigation of the degradation mechanism, the holes and hydroxyl radicals were mainly responsible for the dye's degradation. The obtained photocatalysts displayed promising results with up to 99% of dye degradation, employing conventional visible LED lamps, making the practical use of the catalyst highly viable, as well as the economic matters. Additionally, the synthesized materials' magnetic properties allowed total and efficient separation of the catalyst for its reutilization up to 4 cycles, with no decrease in photocatalytic activity and with low leaching of iron ions to solution.

Effective blockage of chloride ion quenching and chlorinated by-product generation in photocatalytic wastewater treatment

Photocatalytic degradation of pollutants in high salinity wastewater usually shows extremely low activities and produces highly toxic by-products, often related to the presence of excess chloride ion (Cl^-). Herein, we report for the first time that involvement of Cl^- (quenching active species and generating chlorinated by-products) could be effectively blocked during photocatalytic processes. Based on a comprehensive investigation of its mechanism, we found that Cl^- could quench superoxide radicals (O₂^-) through a cyclic indirect quenching model with holes (h⁺) and hydroxyl radicals (OH) quenching as "initiators". Thus, scavenging h⁺ and OH could successfully block the chain reactions between Cl^- and O₂^-, and photocatalytic degradation of methyl orange (a refractory dye, with O₂^- as dominant attacking species) could be enhanced by nearly 50 times, even when Cl^- content was up to 10 wt%. More importantly, both HPLC-MS analyses and DFT calculation validated that, by blocking its quenching effect, Cl^- could be successfully excluded from the pollutant degradation processes, thus preventing the generation of toxic chlorinated by-products. This work provides new insights into control of chlorinated by-products and proposes feasible strategies to extend photocatalytic technology in high salinity wastewater.

Ultrasound-assisted Ti3C2Tx MXene adsorption of dyes: Removal performance and mechanism analyses via dynamic light scattering

Herein, ultrasonication (US)-assisted novel nanomaterial Ti₃C₂T_x MXene was utilized as a selective adsorbent for treatment of synthetic dyes in model wastewater. Two types of US frequencies, 28 and 580 kHz, were applied to disperse MXene to evaluate the feasibility of US-assisted MXene for wastewater treatment. The physico-chemical properties of MXene after US were characterized by Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and zeta potential. According to FTIR and XPS, 28 kHz US-assisted MXene had a greater amount of oxygenated functional groups and dispersion compared to 580 kHz US-assisted and pristine MXene. Subsequently, US-assisted MXene was utilized as an adsorbent for the removal of positively charged methylene blue (MB) and negatively charged methyl orange. Both 28 and 580 kHz US-assisted MXene showed better adsorption performance for only MB compared to stirring-assisted MXene based on kinetics, isotherms, and several water chemistry factors including solution pH, temperature, ionic strength, and humic acid. Advantages of US-assisted MXene for water treatment are its fast kinetics at low dose and high selectivity for positively charged target compounds (i.e., MB). The main adsorption mechanism between MXene and MB was electrostatic interaction (attraction); however, physical properties (i.e., aggregation kinetics and hydrodynamic diameter), measured via dynamic light scattering, were also found to be critical factors in controlling the adsorption performance of the system. Lastly, US-assisted MXene exhibited a high regeneration property, based on 4th adsorption-desorption cycles.

Ultrasonic degradation of selected dyes using Ti3C2Tx MXene as a sonocatalyst

MXene, a new family of two dimensional materials, was utilized as a sonocatalyst in an ultrasonic treatment (US) process for removal of methylene blue (MB) and acid blue 80 (AB). The physico-chemical properties of MXene were characterized using scanning electron microscopy, transmission electron microscopy, porosimetry, and a zeta potential analyzer. Degradation of dyes by US was systemically investigated under several experimental conditions including: power density of US (45, 90, 135, and 180 W L^-1), frequency of US (28 and 970 kHz), pH of dye solution (3.5, 7, and 10.5), solution temperature (293, 303, and 313 K), and addition of hydroxyl radical promotor (H₂O₂) and scavenger (t-BuOH) to concentrations of 25 mM. Based on the experimental results, the quantity of H₂O₂, which was used as an indicator of hydroxyl radical concentration, was an important factor in determining the degradation rate of MB and AB in this US study. Additionally, synergetic indices for removal of both dyes were higher than 1.0 in all cases, indicating the outstanding efficiency of MXene as a sonocatalyst in the US reactor for removal of both, due to an increase in both (i) the quantity of H₂O₂ in the US reactor and (ii) active sites for adsorbates from dispersion effects. A stability test on MXene in the US process was conducted using X-ray diffraction and five-cycle recycling performance tests. Based on our experimental data, MXene can be utilized as a sonocatalyst in the US process for a high removal rate for dyes (e.g., MB).

Preparation of Cu3N/MoS2 Heterojunction through Magnetron Sputtering and Investigation of Its Structure and Optical Performance

Cu₃N/MoS₂ heterojunction was prepared through magnetron sputtering, and its optical band gap was investigated. Results showed that the prepared Cu₃N/MoS₂ heterojunction had a clear surface heterojunction structure, uniform surface grains, and no evident cracks. The optical band gap (1.98 eV) of Cu₃N/MoS₂ heterojunction was obtained by analyzing the ultraviolet-visible transmission spectrum. The valence and conduction band offsets of Cu₃N/MoS₂ heterojunction were 1.42 and 0.82 eV, respectively. The Cu₃N film and multilayer MoS₂ formed a type-II heterojunction. After the two materials adhered to form the heterojunction, the interface electrons flowed from MoS₂ to Cu₃N because the latter had higher Fermi level than the former. This behavior caused the formation of additional electrons in the Cu₃N and MoS₂ layers and the change in optical band gap, which was conducive to the charge separation of electrons in MoS₂ or MoS₂ holes. The prepared Cu₃N/MoS₂ heterojunction has potential application in various high-performance photoelectric devices, such as photocatalysts and photodetectors.

Preparation of zinc tungstate nanomaterial and its sonocatalytic degradation of meloxicam as a novel sonocatalyst in aqueous solution

Zinc tungstate (ZnWO₄) was previously used as a photocatalyst. In this paper, for the first time as an sonocatalyst, the performance of ZnWO₄ for sonocatalytic degradation of meloxicam (MEL) under ultrasonic irradiation were studied. Firstly, ZnWO₄ nanomaterials were synthesized at different acidity (pH = 5, 6, 7, 8, 9) via the hydrothermal method. Utilizing SEM, XRD and EDS techniques to characterize composition and morphology of each product, the same crystal forms, but different morphologies (nano-sheet, nano-microspheres or nano-rod) of ZnWO₄ could be obtained. Secondly, the sonocatalytic activities of ZnWO₄ on degradation of MEL were studied. It was found that the degradation ratio varied with the synthetic pH values, with ZnWO₄ under synthetic pH = 6 exhibiting the best sonocatalytic performance (75.7%). Whilebeing synthesized at this pH value, ZnWO₄nano-microspheres had the largest BET surface area (27.068 m²/g), the smallest particle size (40-60 nm) so as to provide more active sites on its surface, which were able to produce more reactive oxygen species (ROS) and holes under ultrasonic irradiation. These ROS and holes had a positive effect on the degradation of MEL into CO₂, H₂O and inorganic. Thirdly, various influential factors including ultrasonic power intensity, ultrasonic time, catalyst addition dosage, initial concentration of MEL solution and reusability of catalyst were also explored. Under the condition of 10 mg/L MEL concentration, 20 mg catalyst dosage, 120 min irradiation time, 0.278 W/cm² ultrasonic power intensity, the degradation ratio on MEL reached 75.7%. Finally, the presence of hydroxyl radical (OH) and singlet molecular oxygen (¹O₂) in the reaction was confirmed by adding ROS scavenger. The experimental results suggested that ZnWO₄ nanoparticle could be used not only as an effective photocatalyst, but also, under the condition of ultrasonic irradiation, a promising sonocatalyst for degradation of organic pollutants in aqueous media.

Adsorption of Ba2+ and Sr2+ on Ti3C2Tx MXene in model fracking wastewater

Wastewater from hydraulic fracking contains both organic and inorganic pollutants; the latter include radioactive nuclides such as Ba²⁺ and Sr²⁺. We explored whether MXene (Ti₃C₂T_x), a novel adsorbent, could remove Ba²⁺ and Sr²⁺ from model wastewater. Zeta potential analysis showed that MXene had a high negative surface charge. MXene adsorbed Ba²⁺ and Sr²⁺ via electrostatic attraction, as confirmed by the adsorption at different solution pH values and in the presence of various concentrations of other ions (NaCl and CaCl₂). MXene exhibited outstanding adsorption of Ba²⁺ and Sr²⁺, to approximately 180 and 225 mg g^-1, respectively, when 1 g L^-1 MXene was admixed with adsorbates at 2 g L^-1. MXene exhibited very rapid adsorption kinetics, attaining equilibrium within 1 h. X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy revealed that MXene adsorbed Ba²⁺ and Sr²⁺, respectively, via ion exchange and inner-sphere complex formation. Finally, we performed MXene reusability tests; reusability was excellent over at least four cycles. Thus, MXene removed Ba²⁺ and Sr²⁺ from model fracking wastewater.

Fabrication of black TiO2−x/CuFe2O4 decorated on diatomaceous earth with enhanced sonocatalytic activity for ibuprofen mitigation

This study reports facile fabrication of black TiO_2−x/CuFe₂O₄ (Ti³⁺ self-doped titania coupled with copper ferrite), an efficient sonocatalyst for ibuprofen (IBP) mitigation.

Fabrication of a novel magnetic CdS nanorod/NiFe2O4/NaX zeolite nanocomposite with enhanced sonocatalytic performance in the degradation of organic dyes

Herein, magnetically separable CdS nanorods (NRs)/NiFe₂O₄/NaX zeolite ternary nanocomposite was fabricated and applied for the enhanced sonocatalytic degradation of organic dyes.

Post-Treatment of Nanofiltration Polyamide Membrane through Alkali-Catalyzed Hydrolysis to Treat Dyes in Model Wastewater

This research focused on the influence of post-treatment using alkali-catalyzed hydrolysis with a full-aromatic nanofiltration (NF) polyamide membrane and its application to the efficient removal of selected dyes. The post-treated membranes were characterized through Fourier transform infrared spectroscopy, goniometry, and zeta-potential analysis to analyze the treatment-induced changes in the intrinsic properties of the membrane. Furthermore, the changes in permeability induced by the post-treatment were evaluated via the measurement of water flux, NaCl rejection, and molecular weight cutoff (MWCO) under different pH conditions and post-treatment times. Major changes induced by the post-treatment in terms of physicochemical properties were the enhancement of permeability, hydrophilicity, and negative charge due to the hydrolysis of the membrane’s amide bonds. Four different dyes were selected as representative organic pollutants considering the MWCO of the post-treated membranes. Compared with the pristine NF membrane, membranes post-treated at pH 13.5 showed better water flux with similar rejection of the target dyes. On the basis of these results, the proposed post-treatment method for NF membranes can be applied to the removal of organic pollutants of various size.