Iron as electron donor for denitrification: The efficiency, toxicity and mechanism

Sponge iron enriches autotrophic/aerobic denitrifying bacteria to enhance denitrification in sequencing batch reactor

Sponge iron (SFe) coupled with a sludge system has great potential for improving biological denitrification; however, the underlying mechanism is not yet fully understood. In this study, the denitrification performance and microbial characteristics of ordinary sludge and SFe-sludge systems were investigated. Overall, the SFe-sludge reactor had faster ammonium degradation rate (94.0 %) and less nitrate accumulation (1.5-53.3 times lower) than ordinary reactor during the complete operation cycle of sequencing batch reactors. The addition of SFe increased the activities of nitrate and nitrite reductases. The total relative abundance of autotrophic denitrifying bacteria (Acidovorax, Arenimonas, etc.) in the SFe-sludge system after 38 days of operation was found to be 10.6 % higher than that in the ordinary sludge reactor. The aerobic denitrifying bacteria (Dokdonella, Phaeodactylibacter, etc.) was 5.3 % higher than ordinary sludge. The SFe-sludge system improved denitrification by enriching autotrophic/aerobic denitrifying bacteria in low carbon-to-nitrogen ratio wastewater treatment.

Irons differently modulate bacterial guilds for leading to varied efficiencies in simultaneous nitrification and denitrification (SND) within four aerobic bioreactors

As a novel biological wastewater nitrogen removal technology, simultaneous nitrification and denitrification (SND) has gained increasing attention. Iron, serving as a viable material, has been shown to influence nitrogen removal. However, the precise impact of iron on the SND process and microbiome remains unclear. In this study, bioreactors amended with iron of varying valences were evaluated for total nitrogen (TN) removal efficiencies under aerobic conditions. The acclimated control reactor without iron addition (NCR) exhibited high ammonia nitrogen (AN) removal efficiency (98.9%), but relatively low TN removal (78.6%) due to limited denitrification. The reactor containing zero-valent iron (Fe0R) demonstrated the highest SND rate of 92.3% with enhanced aerobic denitrification, albeit with lower AN removal (84.1%). Significantly lower SND efficiencies were observed in reactors with ferrous (Fe2R, 66.3%) and ferric (Fe3R, 58.2%) iron. Distinct bacterial communities involved in nitrogen metabolisms were detected in these bioreactors. The presence of complete ammonium oxidation (comammox) genus Nitrospira and anammox bacteria Candidatus Brocadia characterized efficient AN removal in NCR. The relatively low abundance of aerobic denitrifiers in NCR hindered denitrification. Fe0R exhibited highly abundant but low-efficiency methanotrophic ammonium oxidizers, Methylomonas and Methyloparacoccus, along with diverse aerobic denitrifiers, resulting in lower AN removal but an efficient SND process. Conversely, the presence of Fe2+/Fe3+ constrained the denitrifying community, contributing to lower TN removal efficiency via inefficient denitrification. Therefore, different valent irons modulated the strength of nitrification and denitrification through the assembly of key microbial communities, providing insight for microbiome modulation in nitrogen-rich wastewater treatment.

Mechanisms of nanoscale zero-valent iron mediating aerobic denitrification in Pseudomonas stutzeri by promoting electron transfer and gene expression

Aerobic denitrification and its mechanism by P. stutzeri was investigated in the presence of nanoscale zero-valent iron (nZVI). The removal of nitrate and ammonia was accelerated and the nitrite nitrogen accumulation was reduced by nZVI. The particle size and dosage of nZVI were key factors for enhancing aerobic denitrification. nZVI reduced the negative effects of low carbon/nitrogen, heavy metals, surfactants and salts to aerobic denitrification. nZVI and its dissolved irons were adsorbed into the bacteria cells, enhancing the transfer of electrons from nicotinamide adenine dinucleotide (NADH) to nitrate reductase. Moreover, the activities of NADH-ubiquinone reductase involved in the respiratory system, and the denitrifying enzymes were increased. The expression of denitrifying enzyme genes napA and nirS, as well as the iron metabolism gene fur, were promoted in the presence of nZVI. This work provides a strategy for enhancing the biological denitrification of wastewater using the bio-stimulation of nanomaterials.

Microbially driven Fe-N cycle: Intrinsic mechanisms, enhancement, and perspectives

The iron‑nitrogen (FeN) cycle driven by microbes has great potential for treating wastewater. Fe is a metal that is frequently present in the environment and one of the crucial trace elements needed by microbes. Due to its synergistic role in the microbial N removal process, Fe goes much beyond the essential nutritional needs of microorganisms. Investigating the mechanisms behind the linked Fe-N cycle driven by microbes is crucial. The Fe-N cycle is frequently connected with anaerobic ammonia oxidation (anammox), nitrification, denitrification, dissimilatory nitrate reduction to ammonium (DNRA), Feammox, and simultaneous nitrification denitrification (SND), etc. Although the main mechanisms of Fe-mediated biological N removal may vary depending on the valence state of the Fe, their similar transformation pathways may provide information on the study of certain element-microbial interactions. This review offers a thorough analysis of the facilitation effect and influence of Fe on the removal of nitrogenous pollutants in various biological N removal processes and summarizes the ideal Fe dosing. Additionally, the synergistic mechanisms of Fe and microbial synergistic N removal process are elaborated, covering four aspects: enzyme activity, electron transfer, microbial extracellular polymeric substances (EPS) secretion, and microbial community interactions. The methods to improve biological N removal based on the intrinsic mechanism were also discussed, with the aim of thoroughly understanding the biological mechanisms of Fe in the microbial N removal process and providing a reference and thinking for employing Fe to promote microbial N removal in practical applications.

Enhancement of nitrogen removal in coupling Anammox and DAMO via Fe-modified granular activated carbon

Anaerobic ammonium oxidation (Anammox) coupled with Denitrifying anaerobic methane oxidation (DAMO) is an attractive technology to simultaneously remove nitrogen and mitigate methane emissions from wastewater. However, its nitrogen removal rate is usually limited due to the low methane mass transfer efficiency, low metabolic activity and slow growth rate of functional microorganisms. In this study, GAC and Fe-modified GAC (Fe-GAC) were added into Anammox-DAMO process to investigate their effects on nitrogen removal rates and then reveal the mechanism. The results showed that after 80-day experiments, the total nitrogen removal rate was slightly improved in the presence of GAC (3.94 mg L^-1·d^-1), while it reached high as 16.66 mg L^-1·d^-1 in the presence of Fe-GAC, which was ca.17 times that of non-amended control group (0.96 mg L^-1·d^-1). The addition of Fe-GAC stimulated the secretion of extracellular polymeric substance (EPS), improved the electron transfer capability and promoted the production of Cytochrome C. Besides, the key functional enzyme activities (HZS, HDH and NAR) were highest in the Fe-GAC group, which were approximately 1.06-1.56 times higher than those of GAC-amended and blank control groups. Microbial community analysis showed that the abundance of the DAMO archaea (Candidatus Methanoperedens) and Anammox bacteria (Candidatus Brocadia) were remarkably increased with the addition of Fe-GAC. Functional genes associated with nitrogen removal and methane oxidation in Fe-GAC system were up-regulated. This study provides a promising strategy for achieving high rate of nitrogen removal upon Anammox-DAMO process.

Simultaneous partial nitrification, Anammox and nitrate-dependent Fe(II) oxidation (NDFO) for total nitrogen removal under limited dissolved oxygen and completely autotrophic conditions

Sustainable nitrogen removal from wastewater at reduced energy and/or chemical consumptions is challenging. This paper investigated, for the first time, the feasibility of coupled partial nitrification, Anammox and nitrate-dependent Fe(II) oxidation (NDFO) for sustainable autotrophic nitrogen removal. With NH₄⁺-N as the only nitrogen-containing compound in the influent, near-complete nitrogen removal (a total of 97.5 % with a maximal total nitrogen removal rate of 6.64 ± 2.68 mgN/L/d) was achieved in a sequencing batch reactor for a 203-d operation without organic carbon source addition and forced aeration. Anammox (predominated by Candidatus Brocadia) and NDFO bacteria (such as Denitratisoma) were successfully enriched, with total relative abundances up to 11.54 % and 10.19 %, respectively. Dissolved oxygen (DO) concentration was a key factor affecting the coupling of multi (ammonia oxidization, Anammox, NDFO, iron-reduction, etc.) bacterial communities, resulting in different total nitrogen removal efficiencies and rates. In batch tests, the optimal DO concentration was 0.50-0.68 mg/L with a maximal total nitrogen removal efficiency of 98.7 %. Fe(II) in the sludge not only competed with nitrite oxidizing bacteria for DO to prevent complete nitrification, but promoted the transcription of NarG and NirK genes (10.5 and 3.5 times higher than the group without Fe(II) addition) as indicated by the reverse transcription quantitative polymerase chain reaction (RT-qPCR), resulting in increased NDFO rate (by 2.7 times) and promoted NO₂^--N generated from NO₃^--N, which back fed the Anammox process, achieving near-complete nitrogen removal. The reduction of Fe(III) by iron-reducing bacteria (IRB) and hydrolytic and fermentative anaerobes enabled a sustainable Fe(II)/Fe(III) recycling, avoiding the need in continuous Fe(II) or Fe (III) dosage. The coupled system is expected to benefit the development of novel autotrophic nitrogen removal processes with neglectable energy and material consumptions for the treatment of wastewater with low organic carbon and NH₄⁺-N contents in underdeveloped regions, such as decentralized rural wastewaters.

Aerobic Denitrification Enhanced by Immobilized Slow-Released Iron/Activated Carbon Aquagel Treatment of Low C/N Micropolluted Water: Denitrification Performance, Denitrifying Bacterial Community Co-occurrence, and Implications

The key limiting factors in the treatment of low C/N micropolluted water bodies are deficient essential electron donors for nitrogen removal processes. An iron/activated carbon aquagel (IACA) was synthesized as a slowly released inorganic electron donor to enhance aerobic denitrification performance in low C/N micropolluted water treatment. The denitrification efficiency in IACA reactors was enhanced by more than 56.72% and the highest of 94.12% was accomplished compared with those of the control reactors. Moreover, the COD_Mn removal efficiency improved by more than 34.32% in IACA reactors. The Illumina MiSeq sequencing consequence explained that the denitrifying bacteria with facultative denitrification, iron oxidation, and iron reduction function were located in the dominant species niches in the IACA reactors (e.g., Pseudomonas, Leptothrix, and Comamonas). The diversity and richness of the denitrifying bacterial communities were enhanced in the IACA reactors. Network analysis indicated that aerobic denitrifying bacterial consortia in IACA reactors presented a more complicated co-occurrence structure. The IACA reactors presented the potential for long-term denitrification operation. This study affords a pathway to utilize IACA, promoting aerobic denitrification during low C/N micropolluted water body treatment.

Autotrophic denitrification using Fe(II) as an electron donor: A novel prospective denitrification process

As a newly identified nitrogen loss pathway, the nitrate-dependent ferrous oxidation (NDFO) process is emerging as a research hotspot in the field of low carbon to nitrogen ratio (C/N) wastewater treatment. This review article provides an overview of the NDFO process and summarizes the functional microorganisms associated with NDFO from different perspectives. The potential mechanisms by which external factors such as influent pH, influent Fe(II)/N (mol), organic carbon, and chelating agents affect NDFO performance are also thoroughly discussed. As the electron-transfer mechanism of the NDFO process is still largely unknown, the extensive chemical Fe(II)-oxidizing nitrite-reducing pathway (NDFO_chem) of the NDFO process is described here, and the potential enzymatic electron transfer mechanisms involved are summarized. On this basis, a three-stage electron transfer pathway applicable to low C/N wastewater is proposed. Furthermore, the impact of Fe(III) mineral products on the NDFO process is revisited, and existing crusting prevention strategies are summarized. Finally, future challenges facing the NDFO process and new research directions are discussed, with the aim of further promoting the development and application of the NDFO process in the field of nitrogen removal.

Strategy of nitrate removal in anaerobic ammonia oxidation-dependent processes

The anaerobic ammonium oxidation (anammox), a microbial process that is considered as a low-cost and high efficient wastewater treatment, has received extensive attention with an attractive application prospect. The anammox process reduces nitrite (NO₂^-) to nitrogen gas (N₂) with ammonium (NH₄⁺) as the electron donor. However, some nitrate (NO₃^-) equivalent to 11% of total nitrogen (TN) is generated in this process, which limits the development of anammox. To overcome this problem, many efforts have been made in this regard, mainly combining with other biological treatment methods (denitrification, denitrifying anaerobic methane oxidation, etc.), introducing the substance into anammox process, etc. Herein, we summarized a detailed review of previous researches on the removal of NO₃^- in the anammox-dependent processes. It is hoped that this review could serve as valuable guidance in future research and practical applications of anammox.

Effects of sponge iron dosage on nitrogen removal performance and microbial community structure in sequencing batch reactors

The application of sponge iron (SI) carriers can improve the biochemical treatment performance of sequencing batch reactors (SBR) during wastewater treatment. This study used SBR reactors to explore the effects of SI dosage on the nitrogen removal performance and reactor stability and microbial community structure under low temperature and ultra-low load. In contrast to conventional SBR, the average removal rate of total nitrogen (TN) in the biological sponge iron system (BSIS) was increased by 5.38 % for 45 g/L, 18.93 % for 90 g/L, and 13.52 % for 135 g/L, respectively. The nitrogen removal performance and reactor stability showed the best performance under the SI dosage of 90 g/L. The addition of SI formed the anaerobic-anoxic-aerobic microenvironments, which facilitate the propagation of denitrifying bacteria (Saccharimonadales, Hydrogenophaga) and iron bacteria (Rhodoferax and Acinetobacter) in the BSIS. This study provides a new insight on the application of SI in the wastewater treatment.

New insights on simultaneous nitrate and phosphorus removal in pyrite-involved mixotrophic denitrification biofilter for a long-term operation: Performance change and its underlying mechanism

Simultaneous nitrate and phosphorus removal can be completed by pyrite- and influent organics-involved mixotrophic denitrification and chemical phosphorus removal via iron precipitation. However, so far, how their removal performances change with iron precipitation accumulation remains unclear. In this study, the differences in nitrate and phosphorus removal from municipal tailwater between volcanic and pyrite supported biofilters (V-BF, P-BF) for a long-term operation were investigated, as well as the underlying mechanism for these differences. The nitrate removal efficiencies (NREs) in P-BF were greater than those in V-BF due to the synergistic effect of influent organic and pyrite, as evidenced by comparable TOC consumption and Fe²⁺/SO₄^2- production. The NREs in P-BF were gradually lower than in V-BF as a result of bacterial cell-iron encrustation observed in TEM images, which would deteriorate microbial activity. However, the phosphorus removal efficiencies (PREs) in P-BF remained consistently higher than in V-BF, resulting from chemical phosphorus removal which was confirmed that P, Fe and O elements dominated on the pyrite surface after use by SEM-EDS. The dominant denitrifying bacteria differed significantly, autotrophic and heterotrophic denitrifying microorganisms coexisted in P-BF. The relative abundances of the narG coding gene in P-BF were higher than that in V-BF, which was consistent with the total relative abundances of identified denitrifying bacteria. Besides, the mechanism of simultaneous nitrogen and phosphorus removal in the pyrite-involved mixotrophic denitrification process has been deduced. This work has significant implications for the practical application of a pyrite-involved mixotrophic denitrification process for low C/N wastewater treatment.

Enhanced denitrification of dispersed swine wastewater using Ca(OH)2-pretreated rice straw as a solid carbon source

In a pilot-scale packed bed reactor, the denitrification performance and microbial community structure of the dispersed swine wastewater treatment using calcium hydroxide (Ca(OH)₂) pretreated rice straw as a carbon source were investigated. In a Ca(OH)₂-pretreated rice straw supported denitrification system (Ca(OH)₂-RS), the removal efficiency of NO₃^--N was 96.39% at an influent NO₃^--N load of 0.04 kg/(m³•d). Meanwhile, there was no obvious accumulation of NO₂^--N or chemical oxygen demand (COD) in the effluent of Ca(OH)₂-RS. The contents of soluble microbial byproduct-like substances and tryptophan-like substances in the effluent of Ca(OH)₂-RS were reduced by 46.2% and 43.4%, respectively, compared with the influent. Overall, the Ca(OH)₂-pretreated rice straw system had a strong resistance to fluctuations in water quality conditions, such as influent NO₃^--N and COD concentrations. According to the microbial assay results, the Ca(OH)₂ pretreatment enriched more denitrifying bacteria. Among them, Proteobacteria (42.33%) and Bacteroidetes (35.28%) were the dominant bacteria. Moreover, the main denitrifying functional bacteria, generanorank_f_Saprospiraceae (13.32%), norank_f_Porphyromonadaceae (4.22%), and Flavobacterium (3.25%), were enriched in Ca(OH)₂-RS. This suggested that using Ca(OH)₂-pretreated rice straw as a carbon source was a stable and efficient technology to enhance the denitrification performance of dispersed swine wastewater.

Culture-dependent and culture-independent methods reveal microbe-clay mineral interactions by dissimilatory iron-reducing bacteria in an integral oilfield

Fe(III) may be reasonably considered as one of the most important electron acceptors in petroleum reservoir ecosystems. The microbial mineralization of clay minerals, especially montmorillonite, is also of great significance to the exploration of petroleum and gas reservoirs. The bioreduction mechanisms of iron-poor minerals in petroleum reservoirs have been poorly investigated. This study investigated the bioreduction of montmorillonite by dissimilatory iron-reducing bacteria (DIRB) in petroleum reservoirs based on culture-independent and culture-dependent methods. Microbial diversity analysis revealed that Halolactibacillus, Bacillus, Alkaliphilus, Shewanella, Clostridium, and Pseudomonas were the key genera involved in the bioreduction of Fe(III). Through the traditional culture-dependent method, most of the key genera were isolated from the samples collected from petroleum reservoirs. Traditional culture-dependent methods can be used to reveal the metabolic characteristics of microorganisms (such as iron-reduction efficiency) to further elucidate the roles of different species (B. subtilis and B. alkalitelluris) in the environment. Moreover, many species with high iron-reduction efficiencies and relatively low abundances in the samples, such as Tessaracoccus and Flaviflexus, were isolated from petroleum reservoirs for the first time. The combination of culture-dependent and culture-independent methods can be used to further the understanding of the microbial communities and the metabolic characteristics of DIRB in petroleum reservoirs. Structural alterations that occurred during the interactions of microorganisms and montmorillonite were revealed through scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and X-ray powder diffraction (XRD). The physical and chemical analysis results demonstrated that microorganisms from petroleum reservoirs can dissolve iron-poor montmorillonite and promote the release of interlayer water. The secondary minerals illite and clinoptilolite were observed in bioreduced smectite. The formation of secondary minerals was closely related to the dissolution degrees of minerals based on iron reduction.

Synchronous N and P Removal in Carbon-Coated Nanoscale Zerovalent Iron Autotrophic Denitrification─The Synergy of the Carbon Shell and P Removal

Fe⁰ is a promising electron donor for autotrophic denitrification in the simultaneous removal of nitrate and phosphorus in low C/N wastewater. However, P removal may inevitably inhibit bio-denitrification. It has not been well recognized and led to an overdose of iron materials. This study employed carbon-coated zerovalent iron (Fe⁰@C) to support autotrophic denitrification to mitigate the inhibition effects of P removal and enhance both N and P removal. The critical role of the carbon shell in Fe⁰@C was to block the direct contact between Fe⁰ and P and NO₃^--N, to maintain the Fe⁰ activity. Besides, P inhibited the chemical reduction of NO₃^--N by competing for Fe⁰ active sites. This indirectly boosted H₂ generation and promoted bio-denitrification. P removal displayed negligible effects on microbial species but indirectly enhanced the nitrogen metabolic activities because of promoted H₂ in Fe⁰@C-based autotrophic denitrification. Bio-denitrification, in turn, strengthened Fe-P co-precipitation by promoting the formation of ferric hydroxide as a secondary adsorbent for P removal. This study demonstrated an efficient method for simultaneous N and P removal in autotrophic denitrification and revealed the synergistic interactions among N and P removal processes.

Underestimation about the Contribution of Nitrate Reducers to Iron Cycling Indicated by Enterobacter Strain

Nitrate-reducing iron(II) oxidation (NRFO) has been intensively reported in various bacteria. Iron(II) oxidation is found to be involved in both enzymatic and chemical reactions in nitrate-reducing Fe(II)-oxidizing microorganisms (NRFOMs). However, little is known about the relative contribution of biotic and abiotic reactions to iron(II) oxidation for the common nitrate reducers during the NRFO process. In this study, the typical nitrate reducers, four Enterobacter strains E. hormaechei, E. tabaci, E. mori and E. asburiae, were utilized as the model microorganisms. The comparison of the kinetics of nitrate, iron(II) and nitrite and N₂O production in setups with and without iron(II) indicates a mixture of enzymatic and abiotic oxidation of iron(II) in all four Enterobacter strains. It was estimated that 22−29% of total oxidized iron(II) was coupled to microbial nitrate reduction by E. hormaechei, E. tabaci, E. mori, and E. asburiae. Enterobacter strains displayed an metabolic inactivity with heavy iron(III) encrustation on the cell surface in the NRFOmedium during days of incubation. Moreover, both respiratory and periplasmic nitrate-reducing genes are encoded by genomes of Enterobacter strains, suggesting that cell encrustation may occur with periplasmic iron(III) oxide precipitation as well as the surface iron(II) mineral coating for nitrate reducers. Overall, this study clarified the potential role of nitrate reducers in the biochemical cycling of iron under anoxic conditions, in turn, re-shaping their activity during denitrification because of cell encrustation with iron(III) minerals.

Use of sponge iron as an indirect electron donor to provide ferrous iron for nitrate-dependent ferrous oxidation processes: Denitrification performance and mechanism

Sponge iron (SI) can serve as an indirect electron donor to provide Fe(II) for the nitrate-dependent ferrous oxidation (NDFO) process, producing OH^- and magnetite. The SI-NDFO system mainly uses Fe(OH)₂ as an electron donor, achieving a TN reduction rate of 0.42 mg-TN/(gVSS·h) for a period of at least 90 days. The enrichment of iron-oxidizing bacteria and the competition of iron-carbon micro-electrolysis for reaction sites on the surface of SI are the main reasons for the improvement of total nitrogen removal efficiency (TNRE). With an influent NO₃^--N concentration of 50 mg/L and a SI concentration of 50 g/L (at pH 5.0 and 30 °C), the TNRE reached a maximum level of 38.28%. In addition, reducing the pH environment was found to improve the denitrification efficiency of the SI-NDFO system, although denitrification stability was also reduced as a result. Overall, the SI-mediated NDFO process is a promising technique.

Co-occurrence of autotrophic and heterotrophic denitrification in electrolysis assisted constructed wetland packing with coconut fiber as solid carbon source

Aiming at the problems of lack of carbon sources for nitrogen removal and low phosphorus removal efficiency of constructed wetlands (CWs) in treating wastewater treatment plant (WWTP) effluent, an electrolysis assisted constructed wetland (E-CW) with coconut fiber as substrate and solid carbon sources was constructed. The synthetic secondary effluent was used as the influent of the E-CW with a wastewater treatment capacity of 140 L d^-1. The total nitrogen (TN) and the total phosphorus (TP) removal efficiency of the E-CW with coconut fiber treating WWTP effluent were 69.4% and 93.3%, respectively, which were 54.3% and 88.2% higher than those of CW with coconut fiber and no electrolysis. The removal efficiency of TN was 39.9% higher than that of E-CW with gravel. The current intensity had significant effect on nitrogen removal efficiency and the release of carbon sources from coconut fiber. When current intensity increased from 0.25 A to 1.00 A, the TN removal efficiency and nitrate removal rate increased by 21.1% and 0.21 mg L^-1 h^-1, respectively, and the volatile fatty acids (VFAs) released from coconut fiber increased by 57.7 mg L^-1. The 16S rRNA high-throughput sequencing results indicated that the main functional nitrogen-removing microbes were Hydrogenophaga, Thauera, Rhodanobacteraceae_norank, Xanthobacteraceae_norank, etc. Multiple paths including autotrophic denitrification with hydrogen and Fe²⁺ as electron donors and heterotrophic denitrification were achieved in the system. Meanwhile, the main functional lignocellulose degradation microbes were enriched in the system, including Cytophaga_xylanolytica_group, and Caldilineaceae. Because electrolysis created a favorable environment for them to release carbon sources from coconut fiber. This study provided a new perspective for advanced nutrients removal of WWTP effluent in CWs.

Simultaneous heterotrophic and FeS2-based ferrous autotrophic denitrification process for low-C/N ratio wastewater treatment: Nitrate removal performance and microbial community analysis

Heterotrophic-autotrophic denitrification reduces the cost of wastewater treatment and the risk of excess chemical oxygen demanded (COD) in the effluent. A mixotrophic denitrification system involving mixed heterotrophic and ferrous autotrophic bacteria was investigated to treat low-C/N ratio (C/N, defined as chemical oxygen demand (COD)/total nitrogen (TN)) wastewater with pyrite and organic carbon as electron donors. The system yielded effluent total nitrogen (TN) of 0.38 mg/L in 48 h due to a synergistic effect when the C/N ratio was 0.5 and influent nitrate nitrogen (NO₃^--N) was 20 mg/L; this TN value was significantly lower than those of the heterotrophic system (14.08 mg/L) and ferrous autotrophic system (12.00 mg/L). The highest abundance of the narG gene was observed in the mixotrophic denitrification system, along with more abundant microbial species. The dominant denitrification bacteria in each system included Thaurea, Ferritrophicum, Pseudomonas, and Thiobacillus, which varied with the initial inoculum source and the environment. Nevertheless, the abundance of the heterotrophic bacteria Thaurea decreased with prolonged operation of the systems. Together, these results implied that the simultaneous heterotrophic and FeS₂-based ferrous autotrophic denitrification process can be an alternative approach for the treatment of low-C/N ratio wastewater.

Use of sponge iron dosing in baffled subsurface-flow constructed wetlands for treatment of wastewater treatment plant effluents during autumn and winter

Sponge iron (SI) is widely used in water treatment. As effluents from wastewater treatment plant (WWTP) require advanced treatment methodology, three forms of constructed wetlands (CWs): wetlands with sponge iron (SI), copper sulfate modified sponge iron (Cu/SI), and sponge iron coupled with solid carbon sources (C/SI), have been investigated in this paper for the removal effects of organic matter and nutrients in WWTP effluents, and the corresponding mechanisms have been analyzed. The results showed the effect of baffled subsurface-flow constructed wetland (BSFCW) with SI dosing to purify the WWTP effluents after the stable operation. The water flow of this BSFCW is the repeated combination of upward flow and downward flow, which can provide a longer treatment pathway and microbial exposure time. The average removal rates of total inorganic nitrogen (TIN) were 27.80%, 30.17%, and 44.83%, and the average removal rates of chemical oxygen demand (COD) were 19.96%, 23.73%, and 18.38%. The average removal rates of total phosphorus (TP) were 85.94%, 82.14%, and 83.95%. Cu/SI improved the dissolution of iron, C/SI improved denitrification, and a winter indoor temperature retention measure was adopted to increase the effectiveness of wetland treatment during the winter months. After comprehensively analyzing X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and two-dimensional numerical simulation diagrams, a plausible conjecture that microbes use electrons from SI for autotrophic denitrification is presented. Moreover, the stress effect of wetlands dosed with SI on plants decreased stepwise along the course since C/SI used on wetlands had less impact on plant stress.

Salinity Impact on Composition and Activity of Nitrate-Reducing Fe(II)-Oxidizing Microorganisms in Saline Lakes

Nitrate-reducing Fe(II)-oxidizing (NRFeOx) microorganisms contribute to nitrogen, carbon, and iron cycling in freshwater and marine ecosystems. However, NRFeOx microorganisms have not been investigated in hypersaline lakes, and their identity, as well as their activity in response to salinity, is unknown. In this study, we combined cultivation-based most probable number (MPN) counts with Illumina MiSeq sequencing to analyze the abundance and community compositions of NRFeOx microorganisms enriched from five lake sediments with different salinities (ranging from 0.67 g/L to 346 g/L). MPN results showed that the abundance of NRFeOx microorganisms significantly (P < 0.05) decreased with increasing lake salinity, from 7.55 × 10³ to 8.09 cells/g dry sediment. The community composition of the NRFeOx enrichment cultures obtained from the MPNs differed distinctly among the five lakes and clustered with lake salinity. Two stable enrichment cultures, named FeN-EHL and FeN-CKL, were obtained from microcosm incubations of sediment from freshwater Lake Erhai and hypersaline Lake Chaka. The culture FeN-EHL was dominated by genus Gallionella (68.4%), while the culture FeN-CKL was dominated by genus Marinobacter (71.2%), with the former growing autotrophically and the latter requiring an additional organic substrate (acetate) and Fe(II) oxidation, caused to a large extent by chemodenitrification [reaction of nitrite with Fe(II)]. Short-range ordered Fe(III) (oxyhydr)oxides were the product of Fe(II) oxidation, and the cells were partially attached to or encrusted by the formed iron minerals in both cultures. In summary, different types of interactions between Fe(II) and nitrate-reducing bacteria may exist in freshwater and hypersaline lakes, i.e., autotrophic NRFeOx and chemodenitrification in freshwater and hypersaline environments, respectively. IMPORTANCE NRFeOx microorganisms are globally distributed in various types of environments and play a vital role in iron transformation and nitrate and heavy metal removal. However, most known NRFeOx microorganisms were isolated from freshwater and marine environments, while their identity and activity under hypersaline conditions remain unknown. Here, we demonstrated that salinity may affect the abundance, identity, and nutrition modes of NRFeOx microorganisms. Autotrophy was only detectable in a freshwater lake but not in the saline lake investigated. We enriched a mixotrophic culture capable of nitrate-reducing Fe(II) oxidation from hypersaline lake sediments. However, Fe(II) oxidation was probably caused by abiotic nitrite reduction (chemodenitrification) rather than by a biologically mediated process. Consequently, our study suggests that in hypersaline environments, Fe(II) oxidation is largely caused by chemodentrification initiated by nitrite formation by chemoheterotrophic bacteria, and additional experiments are needed to demonstrate whether or to what extent Fe(II) is enzymatically oxidized.

Nitrogen removal from low carbon/nitrogen polluted water is enhanced by a novel synthetic micro-ecosystem under aerobic conditions: Novel insight into abundance of denitrification genes and community interactions

The main limiting factor in treatment of wastewater with a low carbon/nitrogen ratio is insufficient electron donors for aerobic denitrification. A novel synthetic micro-ecosystem (SM) with functional materials as the core structure was prepared to enhance nitrate removal during wastewater treatment. Nitrate removal in the reactors with SM increased by more than 40 % and reached 97.43 % under aerobic conditions. The abundance of denitrification functional genes in activated sludge increased by 2.7 folds after adding SM. Network analysis showed that the denitrifying bacterial community in the reactors with SM displayed a more abundant symbiotic structure. In the reactors with SM, bacteria with both denitrification and inorganic electron transfer capabilities (such as Paracoccus sp., Thaurea sp., and Achromobacter sp.) occupied dominant niche. A species abundance distribution model indicated more intense competition for the dominant niche for the denitrification community in the reactor with SM. Thus, SM promotes denitrification in polluted water bodies under aerobic conditions.

Recovery of Iron-Dependent Autotrophic Denitrification Activity from Cell-Iron Mineral Aggregation-Induced Reversible Inhibition by Low-Intensity Ultrasonication

Iron-dependent autotrophic denitrification (IDAD) has garnered increasing interests as an efficient method for removing nitrogen from wastewater with a low carbon to nitrogen ratio. However, an inevitable deterioration of IDAD performance casts a shadow over its further development. In this work, the hidden cause for such a deterioration is uncovered, and a viable solution to this problem is provided. Batch test results reveal that the aggregation of microbial cells and iron-bearing minerals induced a cumulative and reversible inhibition on the activity of IDAD sludge. Extracellular polymeric substances were found to play a glue-like role in the cell-iron mineral aggregates, where microbial cells were caged, and their metabolisms were suppressed. Adopting low-intensity ultrasound treatment efficiently restored the IDAD activity by disintegrating such aggregates rather than stimulating the microbial metabolism. Moreover, the ultrasonication-assisted IDAD bioreactor exhibited an advantageous nitrogen removal efficiency (with a maximum enhancement of 72.3%) and operational stability compared to the control one, demonstrating a feasible strategy to achieve long-term stability of the IDAD process. Overall, this work provides a better understanding about the mechanism for the performance deterioration and a simple approach to maintain the stability of IDAD.

Dimension effect of anammox granule: Potential vs performance

Anammox granule is the key support of anammox sludge bed reactor. In this study, the anammox granules from a steady-state reactor were divided into 6 groups to investigate their dimension effects. The results of batch cultivation showed that the anammox granules with VMD (volume surface mean diameter) of 2.17 mm had the maximum SAA (specific anammox activity) of 399.6 ± 37.6 mg-N/(g-VSS·d). The bacterial community analysis demonstrated that Candidatus Kuenenia was the main detectable AnAOB genus in the anammox granules. Q-PCR together with flow cytometry indicated that the total number of viable AnAOB cells ascended with the increasing anammox granular size, suggesting the enhancement of nitrogen removal potential. On the contrary, the mass transfer efficiency descended with the increasing granular size, indicating the restriction of nitrogen removal performance. The maximum SAA was ascribed to the optimal match between nitrogen removal potential and mass transfer efficiency. The results of this study are helpful to comprehend the nitrogen removal capacity of anammox granules and to promote the optimization of anammox process.

Denitrification potential of sodium alginate gel beads immobilized iron-carbon, Zoogloea sp. L2, and riboflavin: Performance optimization and mechanism

A kind of gel beads loaded with iron-carbon powder (Fe-C), Zoogloea sp. L2, and riboflavin (VB2) were prepared through cross-linking of sodium alginate (SA) to establish an immobilized bioreactor. The optimal ratio of SA beads was adjusted by orthogonal experiment. The change of oxidation-reduction potential (ORP) and the concentration of Fe²⁺ and Fe³⁺ showed that the addition of VB2 as a redox mediator can promote denitrification. Under the optimal conditions (carbon to nitrogen (C/N) ratio = 2.0, pH = 7.0, and hydraulic retention time (HRT) = 8 h), the nitrate removal efficiency (NRE) of bioreactor reached 98.48% (1.99 mg L^-1h^-1). Furthermore, Fourier transform infrared spectrometer (FTIR), Fluorescence excitation-emission matrix (EEM), X-ray diffraction (XRD), and gas chromatography (GC) analysis revealed that the immobilization and denitrification of the immobilized bioreactor were excellent. High throughput sequencing also showed that Zoogloea played a vital role in nitrate removal.

Microbial transformation of biogenic and abiogenic Fe minerals followed by in-situ incubations in an As-contaminated vs. non-contaminated aquifer

Fe(III) minerals play a crucial role for arsenic (As) mobility in aquifers as they usually represent the main As-bearing phases. Microbial reductive dissolution of As-bearing Fe(III) minerals is responsible for the release of As and the resulting groundwater contamination in many sites worldwide. So far, in most studies mainly abiogenic iron minerals have been considered. Yet, biogenic minerals that possess different properties to their abiogenic counterparts are also present in the environment. In some environments they dominate the iron mineral inventory but so far, it is unclear what this means for the As mobility. We, therefore, performed an in-situ aquifer Fe(III) minerals exposure experiment i) to evaluate how different biogenic and abiogenic Fe(III) minerals are transformed in a strongly reducing, As-contaminated aquifer (25 m) compared to As-free moderately reducing aquifer (32 m) and ii) to assess which microbial taxa are involved in these Fe(III) minerals transformations. We found that higher numbers of bacteria and archaea were associated with the minerals incubated in the As-contaminated compared to the non-contaminated aquifer and that all Fe(III) minerals were mainly colonized by Fe(III)-reducing bacteria, with Geobacter being the most abundant taxon. Additionally, fermenting microorganisms were abundant on minerals incubated in the As-contaminated aquifer, while methanotrophs were identified on the minerals incubated in the As-free moderately reducing aquifer, implying involvement of these microorganisms in Fe(III) reduction. We observed that biogenic Fe(III) minerals generally tend to become more reduced and when incubated in the As-contaminated aquifer sorbed more As than the abiogenic ones. Most of abiogenic and biogenic Fe(III) minerals were transformed into magnetite while biogenic more crystalline mixed phases were not subjected to visible transformation. This in-situ Fe(III) minerals incubation approach shows that biogenic minerals are more prone to be colonized by (Fe(III)-reducing) microorganisms and bind more As, although ultimately produce similar minerals during Fe(III) reduction.

An efficient way to achieve stable and high-rate ferrous ion-dependent nitrate removal (FeNiR): Batch sludge replacement

Ferrous ion can be used as electron donor for denitrification in the ferrous ion-dependent nitrate removal (FeNiR). To prevent the FeNiR performance decrease caused by iron encrustation, a modified FeNiR process with batch sludge replacement was developed. Based on the decay kinetics of sludge mass and sludge activity, the sludge retention time (SRT) was determined as 40 days in the modified FeNiR process. To keep the FeNiR rate at 0.70 kg-N/(m³·d), the sludge replacement amount was 25% of total sludge every 10 days. The FeNiR efficiency stabilized around 70%. The batch sludge replacement could be an effective method to offset the active sludge decay caused by iron encrustation, and therefore led to the good FeNiR performance. The wasted FeNiR sludge was found to adsorb phosphate at a rate of 0.9 mg-P/(g VS min). The modified FeNiR process was proposed to be coupled with phosphate removal, achieving the co-removal of nitrate and phosphate. The coupled technology is promising due to the less consumption of resources and energy, as well as the less production of excessive sludge.

Microbial coupling mechanisms of nitrogen removal in constructed wetlands: A review

Nitrogen removal through microorganisms is the most important pathway in constructed wetlands (CWs). In this review, we summarize the microbial coupling mechanisms of nitrogen removal, which are the common methods of nitrogen transformation. The electron pathways are shortened and consumption of oxygen and energy is reduced during the coupling of nitrogen transformation functional microorganisms. The highly efficient nitrogen removal mechanisms are cultivated from the design conditions in CWs, such as intermittent aeration and tidal flow. The coupling of microorganisms and substrates enhances nitrogen removal mainly by supplying electrons, and plants affect nitrogen transformation functional microorganisms by the release of oxygen and exudates from root systems as well as providing carriers for microbial attachment. In addition, inorganic elements such as Fe, S and H act as electron donors to drive the autotrophic denitrification process in CWs.

Improvement of ferrous ion-dependent nitrate removal (FeNiR) process with chelating ferrous ion as substrate

In order to improve the ferrous ion-dependent nitrate removal (FeNiR) process, hexametaphosphate chelated ferrous ion was used as substrate to replace the free ferrous ion. With hexametaphosphate chelated ferrous ion as substrate, the influent pH was adjusted to 6.8, and as a result a higher effluent pH (7.2) was detected. The volumetric removal rate (VRR) of nitrate kept at 0.42 ± 0.03 kg-N/(m³∙d) for 48 days and the corresponding nitrogen removal efficiency was 94.39 ± 4.57%. After 88 days of cultivation, FeNiR granules became small because of the oligotrophic substrate. The transmission electron microscope (TEM) analysis showed that less iron encrustation was formed on the surface or in the periplasm of FeNiR cells. The linear curve of the living cell percentage versus time showed that the death rate of FeNiR cells with chelated ferrous ion as substrate was much lower than that with free ferrous ion as substrate (0.4210 vs 0.9221). Without iron encrustation, both the FeNiR activity and alkaline phosphatase (ALP) activity of FeNiR cells kept at high level and thus the efficiency of the FeNiR reactor kept stable and high. With hexametaphosphate chelated ferrous ion as substrate, the pH in bulk liquid was high (pH = 7.2) resulting in the high FeNiR rate, and less iron encrustation was formed around cells ensuring the stability of high FeNiR rate. Therefore, using hexametaphosphate chelated ferrous ion as substrate was an efficient way to improve the FeNiR process.