Non-enzymatic hydrogen peroxide sensor based on MnO2-ordered mesoporous carbon composite modified electrode

Selective Voltammetric Sensor for the Simultaneous Quantification of Tartrazine and Brilliant Blue FCF

Tartrazine and brilliant blue FCF are synthetic dyes used in the food, cosmetic and pharmaceutical industries. The individual and/or simultaneous control of their concentrations is required due to dose-dependent negative health effects. Therefore, the paper presents experimental results related to the development of a sensing platform for the electrochemical detection of tartrazine and brilliant blue FCF based on a glassy carbon electrode (GCE) modified with MnO₂ nanorods, using anodic differential pulse voltammetry. Homogeneous and stable suspensions of MnO₂ nanorods have been obtained involving cetylpyridinium bromide solution as a cationic surfactant. The MnO₂ nanorods-modified electrode showed a 7.9-fold increase in the electroactive surface area and a 72-fold decrease in the electron transfer resistance. The developed sensor allowed the simultaneous quantification of dyes for two linear domains: in the ranges of 0.10-2.5 and 2.5-15 μM for tartrazine and 0.25-2.5 and 2.5-15 μM for brilliant blue FCF with detection limits of 43 and 41 nM, respectively. High selectivity of the sensor response in the presence of typical interference agents (inorganic ions, saccharides, ascorbic and sorbic acids), other food dyes (riboflavin, indigo carmine, and sunset yellow), and vanillin has been achieved. The sensor has been tested by analyzing soft and isotonic sports drinks and the determined concentrations were close to those obtained involving the chromatography technique.

Voltage-Switchable Biosensor with Gold Nanoparticles on TiO2 Nanotubes Decorated with CdS Quantum Dots for the Detection of Cholesterol and H2O2

A thin layer of gold nanoparticles (Au NPs) sputtered on cadmium sulfide quantum dots (CdS QDs) decorated anodic titanium dioxide nanotubes (TNTs) (Au/CdS QDs/TNTs) was fabricated and explored for the nonenzymatic detection of cholesterol and hydrogen peroxide (H₂O₂). Morphological studies of the sensor revealed the formation of uniform nanotubes decorated with a homogeneously dispersed CdS QDs and Au NPs layer. The electrochemical measurements showed an enhanced electrocatalytic performance with a fast electron transfer (∼2 s) between the redox centers of each analyte and electrode surface. The hybrid nanostructure (Au/CdS QDs/TNTs) electrode exhibited about a 6-fold increase in sensitivity for both cholesterol (10,790 μA mM^-1 cm^-2) and H₂O₂ (78,833 μA mM^-1 cm^-2) in analyses compared to the pristine samples. The hybrid electrode utilized different operational potentials for both analytes, which may lead to a voltage-switchable dual-analyte biosensor with a higher selectivity. The biosensor also demonstrated a good reproducibility, thermal stability, and increased shelf life. In addition, the clinical significance of the biosensor was tested for cholesterol and H₂O₂ in real blood samples, which showed maximum relative standard deviations of 1.8 and 2.3%, respectively. These results indicate that a Au/CdS QDs/TNTs-based hybrid nanostructure is a promising choice for an enzyme-free biosensor due to its suitable band gap alignment and higher electrocatalytic activities.

Unique Nonenzymatic Glucose Sensor Using a Hollow-Shelled Triple Oxide Mn-Cu-Al Nanocomposite

Glucose monitoring devices for diabetes mellitus, which is a worldwide significant health issue, have attracted attention of many researchers. Herein, we report a hollow Mn-Cu-Al oxide nanocomposite (HMCA) by a microwave-assisted technique showing excellent sensing abilities toward glucose. Also, it possesses a superb supercapacitor activity described in our previous paper. The sensitivity value of the nanocomposite is 2.194 mA mM^-1 cm^-2 with a low detection limit of 0.43 μM (S/N = 3). The high sensitivity and low detection limit were the results of the large surface area of the nanocomposite and the redox nature of CuO and MnO₂. It shows a selective detection of glucose levels in blood serum. The hollow nanocomposite has been useful for monitoring the glucose level in blood serum and holds great potential for diabetes mellitus and clinical diagnosis.

Engineering two-dimensional metal oxides via surface functionalization for biological applications

Schematic illustration of 2D MO nanosheets for applications in biosystems.

Morphology-dependent MnO2/nitrogen-doped graphene nanocomposites for simultaneous detection of trace dopamine and uric acid

Four nanostructured MnO₂ with various controllable morphologies, including nanowires, nanorods, nanotubes and nanoflowers were synthesized, and then further composited with nitrogen-doped graphene (NG) with the assistance of ultrasonication. The surface morphologies, phase structures, and electrochemical performances of the proposed MnO₂/NG nanohybrids were investigated by various techniques, and their catalytic activities on the electrooxidation of dopamine (DA) and uric acid (UA) were compared systematically. The sensing performances were found to be highly correlated with their morphologies. Among these morphologies, the nanoflower-like MnO₂, composited with NG, displayed the most sensitive response signals for DA and UA. The boosted electrocatalytic activity was ascribed to the unique porous structure, large electroactive area, and low charge transfer resistance (R_ct), which facilitated the electron transfer between electrode and analytes. Two linear response ranges (0.1 μM-10 μM and 10 μM-100 μM) were accompanied with very low detection limits of 34 nM and 39 nM for DA and UA, respectively. Moreover, the successful application of the MnO₂NFs/NG composites for the simultaneous detection of DA and UA in human serum was realized using second-derivative linear sweep voltammetry (SDLSV). These findings give valuable insights for understanding the morphology-dependent sensing properties of MnO₂ based nanomaterials, which is conducive to the rapid development of ubiquitous MnO₂-based electrochemical sensors.

A novel non-enzymatic H2O2 sensor using ZnMn2O4 microspheres modified glassy carbon electrode

With a facile solvothermal technique, ZnMn₂O₄ microspheres were synthesized in this work, which were used as enzyme mimics for the electrocatalytic reduction of H₂O₂. The morphology, crystal phase and structure of the ZnMn₂O₄ microspheres underwent characterization under X-ray diffraction spectroscopy, Raman spectroscopy, energy-dispersive spectroscopy, and scanning electron microscopy. The synthesized ZnMn₂O₄ microspheres showed an average diameter of 2 μm with great crystallinity, and exhibited excellent catalytical activity towards H₂O₂ electroreduction in alkaline media. The glassy carbon electrode modified by ZnMn₂O₄ microspheres showed a linear amperometric response for H₂O₂ in a wide concentration range of 0.02 ˜ 15 mM with detection limit of 0.13 μM under the optimized conditions. Besides, the sensor proposed here was successfully used to determine H₂O₂ in milk, suggesting that ZnMn₂O₄ microspheres can be used for non-enzymatic electrochemical sensor applications.

Detection of Triacetone Triperoxide (TATP) Precursors with an Array of Sensors Based on MoS₂/RGO Composites

Triacetone triperoxide (TATP) is a self-made explosive synthesized from the commonly used chemical acetone (C₃H₆O) and hydrogen peroxide (H₂O₂). As C₃H₆O and H₂O₂ are the precursors of TATP, their detection is very important due to the high risk of the presence of TATP. In order to detect the precursors of TATP effectively, hierarchical molybdenum disulfide/reduced graphene oxide (MoS₂/RGO) composites were synthesized by a hydrothermal method, using two-dimensional reduced graphene oxide (RGO) as template. The effects of the ratio of RGO to raw materials for the synthesis of MoS₂ on the morphology, structure, and gas sensing properties of the MoS₂/RGO composites were studied. It was found that after optimization, the response to 50 ppm of H₂O₂ vapor was increased from 29.0% to 373.1%, achieving an increase of about 12 times. Meanwhile, all three sensors based on MoS₂/RGO composites exhibited excellent anti-interference performance to ozone with strong oxidation. Furthermore, three sensors based on MoS₂/RGO composites were fabricated into a simple sensor array, realizing discriminative detection of three target analytes in 14.5 s at room temperature. This work shows that the synergistic effect between two-dimensional RGO and MoS₂ provides new possibilities for the development of high performance sensors.

An ultrasensitive electrochemical immunosensor based on C60-modified polyamidoamine dendrimers and Au NPs for co-catalytic silver deposition

C₆₀-Modified polyamidoamine dendrimers and Au NPs for the co-catalytic deposition of silver, used for ultrasensitive electrochemical immunosensing.

One-pot synthesis of Ni nanoparticle/ordered mesoporous carbon composite electrode materials for electrocatalytic reduction of aromatic ketones

A simple one-pot synthesis of Ni nanoparticle/ordered mesoporous carbon composite electrode materials is demonstrated for electrosynthesis for the first time. The obtained nanocomposites have uniform mesopore sizes (3.0-3.7 nm), large specific surface areas (506-633 m² g^-1), high pore volumes (0.28-0.38 cm³ g^-1), well-graphitized carbon frameworks, and uniformly dispersed Ni nanoparticles (7-15 nm) embedded in the carbon pore walls. The prepared materials show very high performance in the selective (∼84%) electrocatalytic reduction of aromatic ketones into alcohols (∼79%).

Recent Trends on Electrochemical Sensors Based on Ordered Mesoporous Carbon

The past decade has seen an increasing number of extensive studies devoted to the exploitation of ordered mesoporous carbon (OMC) materials in electrochemistry, notably in the fields of energy and sensing. The present review summarizes the recent achievements made in field of electroanalysis using electrodes modified with such nanomaterials. On the basis of comprehensive tables, the interest in OMC for designing electrochemical sensors is illustrated through the various applications developed to date. They include voltammetric detection after preconcentration, electrocatalysis (intrinsically due to OMC or based on suitable catalysts deposited onto OMC), electrochemical biosensors, as well as electrochemiluminescence and potentiometric sensors.

A non-enzymatic amperometric hydrogen peroxide sensor based on iron nanoparticles decorated reduced graphene oxide nanocomposite

A simple and facile green process was used for the synthesis of iron nanoparticles (FeNPs) decorated reduced graphene oxide (rGO) nanocomposite by using Ipomoea pes-tigridis leaf extract as a reducing and stabilizing agent. The as-prepared rGO/FeNPs nanocomposite was characterized by transmission electron microscopy, X-ray spectroscopy and Fourier transform infrared spectroscopy. The nanocomposite was further modified on the glassy carbon electrode and used for non-enzymatic sensing of hydrogen peroxide (H₂O₂). Cyclic voltammetry results reveal that rGO/FeNPs nanocomposite has excellent electro-reduction behavior to H₂O₂ when compared to the response of FeNPs and rGO modified electrodes. Furthermore, the nanocomposite modified electrode shows 9 and 6 folds enhanced reduction current response to H₂O₂ than that of rGO and FeNPs modified electrodes. Amperometric method was further used to quantify the H₂O₂ using rGO/FeNPs nanocomposite, and the response was linear over the concentration ranging from 0.1μM to 2.15mM. The detection limit and sensitivity of the sensor were estimated as 0.056μM and 0.2085μAμM^-1cm^-2, respectively. The fabricated sensor also utilized for detection of H₂O₂ in the presence of potentially active interfering species, and found high selectivity towards H₂O₂.

Redox mediated synthesis of hierarchical Bi2O3/MnO2 nanoflowers: a non-enzymatic hydrogen peroxide electrochemical sensor

Redox mediated synthesis of Bi₂O₃/MnO₂ nanoflowers for efficient electrochemical sensing of hydrogen peroxide down to 0.05 μM.

Controllable Synthesis of Formaldehyde Modified Manganese Oxide Based on Gas-Liquid Interfacial Reaction and Its Application of Electrochemical Sensing

Controllable synthesis of manganese oxides was performed via a simple one-step synthetic method. Then obtained manganese oxides which exhibit flower-like, cloud-like, hexagon-like, and rod-like morphologies were modified by formaldehyde based on a simple self-made gas-liquid reaction device respectively and the modified manganese oxides with coral-like, scallop-like and rod-like morphology were synthesized accordingly. The obtained materials were characterized and the formation mechanism was also researched. Then the modified manganese oxides were used to fabricate electrochemical sensors to detect H2O2. Comparison of electrochemical properties between three kinds of modified manganese oxides was investigated and the best one has been successfully employed as H2O2 sensor which shows a low detection limit of 0.01 μM, high sensitivity of 162.69 μA mM(-1) cm(-2), and wide linear range of 0.05 μM-12.78 mM. The study provides a new method for controllable synthesis of metal oxides, and electrochemical application of formaldehyde modified manganese oxides will provides a new strategy for electrochemical sensing with high performance, low cost, and simple fabrication.

Electroanalysis at the nanoscale

This article reviews the state of the art of silicon chip-based nanoelectrochemical devices for sensing applications. We first describe analyte mass transport to nanoscale electrodes and emphasize understanding the importance of mass transport for the design of nanoelectrode arrays. We then describe bottom-up and top-down approaches to nanoelectrode fabrication and integration at silicon substrates. Finally, we explore recent examples of on-chip nanoelectrodes employed as sensors and diagnostics, finishing with a brief look at future applications.

Novel silver nanoparticle-manganese oxyhydroxide-graphene oxide nanocomposite prepared by modified silver mirror reaction and its application for electrochemical sensing

A gas/liquid interface will be formed when the free volatilized methyl aldehyde gas begins to dissolve in to solution. On the basis of the traditional silver mirror reaction, silver nanoparticle-manganese oxyhydroxide-graphene oxide (Ag-MnOOH-GO) nanocomposite was synthesized at the gas/liquid interface without any protection of inert gas at room temprature. The morphology of the nanocomposites could be controlled by adjusting the reaction temperature and time. The morphology and composition of the nanocomposites were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The composites were then applied for electrochemical sensing. The electrochemical investigation for the sensor indicates that it has excellent property to catalyze H2O2, and could detect H2O2 with a low detection limit of 0.2μM and wide linear range of 0.5 μM to 17.8 mM. The present study provides a general platform for the controlled synthesis of nanomaterials and can be extended to other optical, electronic, and magnetic nanocompounds.

Non-enzymatic hydrogen peroxide electrochemical sensor based on a three-dimensional MnO2 nanosheets/carbon foam composite

Three dimensional MnO₂ nanosheets/carbon foam has been fabricated and they exhibit promising electrochemical sensing performance for nonenzymatic H₂O₂ detection.

Mesoporous nanogold–MnO2–poly(o-phenylenediamine) hollow microspheres as nanotags and peroxidase mimics for sensing biomolecules

Mesoporous MnO₂ nanotags as peroxidase mimics for sensing biomolecules.

Electrical characterization and hydrogen peroxide sensing properties of gold/Nafion:polypyrrole/MWCNTs electrochemical devices

Electrochemical devices using as substrates copier grade transparency sheets are developed by using ion conducting Nafion: polypyrrole mixtures, deposited between gold bottom electrodes and upper electrodes based on Multi Walled Carbon Nanotubes (MWCNTs). The electrical properties of the Nafion:polypyrrole blends and of the gold/Nafion:polypyrrole/MWCNTs devices are investigated under dry conditions and in deionized water by means of frequency dependent impedance measurements and time domain electrical characterization. According to current-voltage measurements carried out in deionized water, the steady state current forms cycles characterized by redox peaks, the intensity and position of which reversibly change in response to H₂O₂, with a lower detection limit in the micromolar range. The sensitivity that is obtained is comparable with that of other electrochemical sensors that however, unlike our devices, require supporting electrolytes.