In situ bismuth-film electrode for square-wave cathodic voltammetric detection of pendimethalin at nanomolar level

Sensors Applied for the Detection of Pesticides and Heavy Metals in Freshwaters

Water is essential for every life living on the planet. However, we are facing a more serious situation such as water pollution since the industrial revolution. Fortunately, many efforts have been done to alleviate/restore water quality in freshwaters. Numerous sensors have been developed to monitor the dynamic change of water quality for ecological, early warning, and protection reasons. In the present review, we briefly introduced the pollution status of two major pollutants, i.e., pesticides and heavy metals, in freshwaters worldwide. Then, we collected data on the sensors applied to detect the two categories of pollutants in freshwaters. Special focuses were given on the sensitivity of sensors indicated by the limit of detection (LOD), sensor types, and applied waterbodies. Our results showed that most of the sensors can be applied for stream and river water. The average LOD was72.53±12.69 ng/ml (n=180) for all pesticides, which is significantly higher than that for heavy metals (65.36±47.51 ng/ml,n=117). However, the LODs of a considerable part of pesticides and heavy metal sensors were higher than the criterion maximum concentration for aquatic life or the maximum contaminant limit concentration for drinking water. For pesticide sensors, the average LODs did not differ among insecticides (63.83±17.42 ng/ml,n=87), herbicides (98.06±23.39 ng/ml,n=71), and fungicides (24.60±14.41 ng/ml,n=22). The LODs that differed among sensor types with biosensors had the highest sensitivity, while electrochemical optical and biooptical sensors showed the lowest sensitivity. The sensitivity of heavy metal sensors varied among heavy metals and sensor types. Most of the sensors were targeted on lead, cadmium, mercury, and copper using electrochemical methods. These results imply that future development of pesticides and heavy metal sensors should (1) enhance the sensitivity to meet the requirements for the protection of aquatic ecosystems and human health and (2) cover more diverse pesticides and heavy metals especially those toxic pollutants that are widely used and frequently been detected in freshwaters (e.g., glyphosate, fungicides, zinc, chromium, and arsenic).

Catalytic Activity of Bimetallic (Ruthenium/Palladium) Nano-alloy Decorated Porous Carbons Toward Reduction of Toxic Compounds

Chicken feather-derived high-surface-area porous activated carbon (CFAC) material was prepared using chemical activation. A new composite composed of Ru-Pd nanoparticles supported on CFAC (Ru-Pd@CFAC) has been prepared by microwave-thermal reduction in the presence of the support. Characterization by XRD, Raman, BET, FE-SEM/TEM, FT-IR, TGA, XPS, HAADF-STEM-EDS, H₂ -chemisorption, H₂ -TPR, and ICP-AES was used to analyze the catalyst. This catalyst is found to be efficient for the reduction of hexavalent chromium (Cr^VI ), potassium ferricyanide (K₃ [Fe(CN)₆ ]), 4-nitrophenol (4-NP), and pendimethalin (PDM), at room temperature, and remains stable, even after several repeated runs. Moreover, it showed excellent catalytic activity compared with the monometallic counterparts.

A simple stripping voltammetric method for the determination of a new anticancer prodrug in serum

The determination of ethyl [4-oxo-8-(3-chlorophenyl)-4,6,7,8-tetrahydroimidazo[2,1-c][1,2,4]triazin-3-yl]acetate (ETTA), a new anticancer prodrug, using adsorptive stripping voltammetry (AdSV) was described for the first time. This method is based on adsorptive/reductive behaviour of ETTA at an in situ plated bismuth film electrode (BiFE) as a sensor. A number of experimental variables (e.g., a composition and pH of the supporting electrolyte, the conditions of bismuth film deposition, an accumulation potential and time, the scan rate, etc.) were thoroughly studied in order to achieve a high sensitivity. Experimental results under optimized conditions revealed an excellent linear correlation between the monitored voltammetric peak current and the ETTA concentration in the range of 2-50μgL^-1 following an accumulation time of 300s. The limit of detection (LOD) for ETTA following 300s of an accumulation time was 0.4μgL^-1. The proposed facile, sensitive and inexpensive method was successfully applied to the determination of ETTA in serum. The investigated prodrug was extracted from serum using SPE method.

Environmentally-friendly in situ plated bismuth-film electrode for the quantification of the endocrine disruptor parathion in skimmed milk

An in situ bismuth-film electrode (BiFE) together with square-wave cathodic voltammetry (SWCV) was used to determine the concentration of the endocrine disruptor parathion in skimmed milk. The experimental conditions (deposition time, deposition potential and Bi (III) concentration) were optimized for the preparation of the BiFE. A glassy carbon electrode was used as the substrate. The selection of the chemical composition of the supporting electrolyte and the solution pH was aimed at improving the reduction of parathion at the BiFE surface. In addition, the parameters of the square-wave cathodic voltammetry were adjusted to improve the sensor performance. A cathodic current identified at -0.523 V increased linearly with the parathion concentration in the range of 0.2-2.0 μmol L(-1) (R=0.999). The sensitivity of the calibration curve obtained was 4.09 μA L μmol(-1), and the limits of detection (LOD) and quantification (LOQ) were 55.7 nmol L(-1) and 169.0 nmol L(-1), respectively. The performance of the sensor was tested using a sample of skimmed milk with parathion added. The same determination was carried out by UV-vis spectroscopy and the results obtained were used for the statistical evaluation of the data obtained.

Silver nanoparticle-modified electrode for the determination of nitro compound-containing pesticides

This paper reports the electroanalytical determination of pendimethalin and ethyl parathion by square-wave adsorptive stripping voltammetry using a material comprised of chitosan-stabilized silver nanoparticles to modify a glassy carbon electrode. Under optimized experimental conditions, the peak current was found to vary linearly with the concentration of pendimethalin in the range of 70 to 2000 nmol L(-1) and with concentration of ethyl parathion in the range of 40 to 8000 nmol L(-1). Detection limits of 36 and 40 nmol L(-1) were obtained for pendimethalin and ethyl parathion, respectively. The silver - nanoparticle-modified electrode was successfully employed for the analysis of pesticides in tap and mineral water (pendimethalin) and in lettuce and honey (ethyl parathion) samples. Pendimethalin recovery was between 94 and 100 %, and ethyl parathion recovery was between 97 and 101 %, indicating no significant matrix interference effects on the analytical results. The accuracy of the electroanalytical methodology using the proposed modified electrode was also compared to that of the UV-vis spectrophotometric method.