Hollow ZIFs-derived nanoporous carbon for efficient capacitive deionization

A confined expansion pore-making strategy to transform Zn-MOF to porous carbon nanofiber for water treatment: Insight into formation and degradation mechanism

Electrospinning MOFs nanoparticles derived porous carbon nanofibers with rational structure and design are recently as environmentally friendly and highly efficient catalytic materials for wastewater treatment. However, most of the pore-making strategies are based on precursors structural shrinkage during pyrolysis, which is a challenge to create abundant large pores and open channels. Here, a confined expansion pore-making strategy with active MOF is introduced, where energetic Zn-MOF (Zn2+/triazole) and ZIF-67 (Co2+/dimethylimidazole) are utilized as pore forming additive and precursor of active sites, respectively. The high nitrogen content gives triazole the ability to puff up and realizes N-doped during pyrolysis. Moreover, degradation mechanisms and pathways of pollutants were measured by 3D EEM, LC-MS, quenching experiments, and Fukui function. This pore-making strategy via energetic MOF local contraction and expansion provides a novel method to prepare diversiform function porous carbon materials for environmental remediation.

A mini review on metal-organic framework-based electrode materials for capacitive deionization

Capacitive deionization (CDI) is an electrochemical method of extracting ions from solution at potentials below electrolysis. It has various applications ranging from water remediation and desalination to heavy metal removal and selective resource recovery. A CDI device applies an electrical charge across two porous electrodes to attract and remove ions without producing waste products. It is generally considered environmentally friendly and promising for sustainability, yet ion removal efficiency still falls short of more established filtration methods. Commercially available activated carbon is typically used for CDI, and its ion adsorption capacity is low at approximately 20-30 mg g-1. Recently, much interest has been in the highly porous and well-structured family of materials known as metal-organic frameworks (MOFs). Most MOFs are poor conductors of electricity and cannot be directly used to make electrodes. A common workaround is to pyrolyze the MOF to convert its organic components to carbon while maintaining its underlying microstructure. However, most MOF-derived materials only retain partial microstructure after pyrolysis and cannot inherit the robust porosity of the parent MOFs. This review provides a systematic breakdown of structure-performance relationships between a MOF-derived material and its CDI performance based on recent works. This review also serves as a starting point for researchers interested in developing MOF-derived materials for CDI applications.

Nanoarchitectonics of heteroatom-doped hierarchical porous carbon derived from carboxymethyl cellulose carbon aerogel and metal-organic framework for capacitive deionization

Capacitive deionization (CDI) using porous materials offers a sustainable solution for providing affordable freshwater, but the low salt adsorption rate of benchmark carbon materials significantly limit the practical implementation. Herein, we utilized carboxymethyl cellulose sodium (CMC) as the carbon skeleton to produce a composite carbon aerogel loaded with ZIF-8 (ZIF-8/CMC-CA). The presence of ZIF-8 nanoparticles improved the pore structure of the material and provides a certain pseudo capacitance by introducing N. Compared with ZIF-8 derived carbons (ZIF-8-C), the CMC provided a good three-dimensional structure for the dispersion of ZIF-8 nanoparticles, reduced the agglomeration of particles. Furthermore, numerous carboxyl and hydroxyl groups on CMC enhanced the hydrophilicity of materials. Due to the interconnected structure, ZIF-8/CMC-CA exhibited excellent conductivity, a high specific surface area, and offered suitable channels for the rapid entry and exit of ions. In a three-electrode system, the total specific capacitance of the ZIF-8/CMC-CA electrode was 357.14 F g^-1. The adsorption rate of ZIF-8/CMC-CA was 2.02 mg g^-1 min^-1 in a 500 mg L^-1 NaCl solution. This study may provide new insight for modifying and fabricating electrode materials for practical CDI applications.

Novel design constructed In2S3@SnO2 hollow heterojunctions by insufficiently etched MOFs as framework for photoelectrochemical bioanalysis

Compared to sufficiently etched MOFs materials, insufficiently etched MOFs materials tend to display unsatisfactory performance due to their immature structure and have been eliminated from scientific research. Herein, this work reported a novel In₂S₃@SnO₂ heterojunction (In₂S₃@SnO₂-HSHT) materials, which were stably synthesized in high temperature aqueous environment and equipped extraordinary photoelectrochemical (PEC) properties, fabricated by a succinct hydrothermal synthesis method using insufficiently etched MIL-68 as a self-sacrificing template. Compared with the control groups and In₂S₃@SnO₂ heterojunctions with collapse morphology synthesized by sufficiently etched MIL-68 in high temperature aqueous environment, In₂S₃@SnO₂-HSHT synthesized from insufficiently etched MIL-68 as a template had a massively enhanced light-harvesting capability and generated more photoinduced charge carriers due to its well-preserved hollow structure. Therefore, based on outstanding PEC performance of In₂S₃@SnO₂-HSHT, the established PEC label-free signal-off immunosensor to detect CYFRA 21-1, revealing vivid selectivity, stability, and reproducibility. This novel strategy adopted the insufficient chemical etching method neglected by the mainstream chemical etching approaches, which solved the challenge that the stability of the sufficient etched MOFs with hollow structure cannot be maintained under the subsequent high temperature aqueous reaction conditions, and was further applied to the design of hollow heterojunction materials for photoelectrochemical fields.

A Single-Atom Fe-N-C Catalyst with Ultrahigh Utilization of Active Sites for Efficient Oxygen Reduction

Fe-N-C single-atom catalysts (SACs) are emerging as a promising class of electrocatalysts for the oxygen reduction reaction (ORR) to replace Pt-based catalysts. However, due to the limited loading of Fe for SACs and the inaccessibility of internal active sites, only a small portion of the sites near the external surface are able to contribute to the ORR activity. Here, this work reports a metal-organic framework-derived Fe-N-C SAC with a hierarchically porous and concave nanoarchitecture prepared through a facile but effective strategy, which exhibits superior electrocatalytic ORR activity with a half-wave potential of 0.926 V (vs RHE) in alkaline media and 0.8 V (vs RHE) in acidic media while maintaining excellent stability. The superior ORR activity of the as-designed catalyst stems from the unique architecture, where the hierarchically porous architecture contains micropores as Fe SAC anchoring sites, meso-/macro-pores as accessible channels, and concave shell for increasing external surface area. The unique architecture has dramatically enhanced the utilization of previously blocked internal active sites, as confirmed by a high turnover frequency of 3.37 s^-1 and operando X-ray absorption spectroscopy analysis with a distinct shift of adsorption edge.

Knowledge and Technology Used in Capacitive Deionization of Water

The demand for water and energy in today’s developing world is enormous and has become the key to the progress of societies. Many methods have been developed to desalinate water, but energy and environmental constraints have slowed or stopped the growth of many. Capacitive Deionization (CDI) is a very new method that uses porous carbon electrodes with significant potential for low energy desalination. This process is known as deionization by applying a very low voltage of 1.2 volts and removing charged ions and molecules. Using capacitive principles in this method, the absorption phenomenon is facilitated, which is known as capacitive deionization. In the capacitive deionization method, unlike other methods in which water is separated from salt, in this technology, salt, which is a smaller part of this compound, is separated from water and salt solution, which in turn causes less energy consumption. With the advancement of science and the introduction of new porous materials, the use of this method of deionization has increased greatly. Due to the limitations of other methods of desalination, this method has been very popular among researchers and the water desalination industry and needs more scientific research to become more commercial.

MOF-Derived Nanoporous Carbon Incorporated in the Cation Exchange Membrane for Gradient Power Generation

Ion exchange membranes (IEMs), as a part of the reverse electrodialysis (RED) system, play an important role in salinity gradient power (SGP) generation. Structure optimization of IEMs is critical to increase the power production by RED. In this work, metal organic framework (MOF)-derived nanoporous carbons (hollow zeolitic imidazolate framework (ZIF)-derived nanoporous carbons, HZCs) were incorporated in a sulfonated poly (2, 6-dimethyl-1,4-phenylene oxide) (sPPO) membrane to prepare an organic−inorganic nanocomposite cation exchange membrane (CEM). Physicochemical properties, electrochemical properties, and power generation of the synthesized nanocomposite membranes with different HZCs loading were characterized. The results show that the incorporated HZCs could tailor the microstructure of the membrane matrix, providing a superior performance of the nanocomposite membrane. With a HZCs loading of 1.0 wt.%, the nanocomposite membrane possessed the highest permselectivity of 77.61% and the lowest area resistance of 0.42 Ω·cm², along with a super gross power density of 0.45 W/m², which was 87.5% (about 1.87 times) higher than that of the blank sPPO membrane. Therefore, incorporating of an appropriate amount of HZCs in the ion-exchange membrane can improve the performance of the membrane, providing a promising method to increase the power generation of the RED system.

Nanoarchitectonics of Metal-Organic Frameworks for Capacitive Deionization via Controlled Pyrolyzed Approaches

Next-generation desalination technologies are needed to meet the increasing demand for clean water. Capacitive deionization (CDI) is a thermodynamically efficient technique to treat non-potable water with relatively low salinity. The salt removal capacity and rate of CDI are highly dependent on the electrode materials, which are preferentially porous to store ions through electrosorption and/or redox reactions. Metal-organic frameworks (MOFs) with "infinite" combinations of transition metals and organic linkers simplify the production of carbonaceous materials often with redox-active components after pyrolysis. MOFs-derived materials show great tunability in both compositions and structures but require further refinement to improve CDI performance. This review article summarizes recent progress in derivatives of MOFs and MOF-like materials used as CDI electrodes, focusing on the structural and compositional material considerations as well as the processing parameters and electrode architectures of the device. Furthermore, the challenges and opportunities associated with this research area are also discussed.

The Surge of Metal-Organic-Framework (MOFs)-Based Electrodes as Key Elements in Electrochemically Driven Processes for the Environment

Metal–organic-frameworks (MOFs) are emerging materials used in the environmental electrochemistry community for Faradaic and non-Faradaic water remediation technologies. It has been concluded that MOF-based materials show improvement in performance compared to traditional (non-)faradaic materials. In particular, this review outlines MOF synthesis and their application in the fields of electron- and photoelectron-Fenton degradation reactions, photoelectrocatalytic degradations, and capacitive deionization physical separations. This work overviews the main electrode materials used for the different environmental remediation processes, discusses the main performance enhancements achieved via the utilization of MOFs compared to traditional materials, and provides perspective and insights for the further development of the utilization of MOF-derived materials in electrified water treatment.

Enhanced electrochemical and capacitive deionization performance of metal organic framework/holey graphene composite electrodes

In this paper, we designed and prepared a novel metal organic framework (MOF)/holey graphene (HG) composites as electrode materials for electrochemistry and capacitive deionization (CDI). The MOF nanoparticles were attached to the surface of the HG sheets to form layered porous structure, which promoted the transport of ions and electrons in the electrode/electrolyte interfaces. Additionally, the synergistic effect of these composite electrodes, which combined pseudocapacitance performance of MOF and the high conductivity of graphene, contributed to enhancing the performance of electrochemistry and CDI. The MOF/HG-2 exhibited high capacitances of 526 F g^-1 at current rates of 0.1 A g^-1, low charge transfer resistance of 0.53 Ω, and excellent cycling stability (retention of about 90.3% after 5000 cycles at 2 A g^-1). As electrode materials for CDI, the MOF/HG-2 displayed a remarkable electrosorption capacity of 39.6 mg g^-1 with initial salt concentration of 800 mg L^-1, and there was no obvious attenuation after 20 CDI regeneration cycles. These results confirmed that MOF/HG was a promising electrode material for the actual application of CDI.

Efficient Removal of Organic Pollutants by Metal-organic Framework Derived Co/C Yolk-Shell Nanoreactors: Size-Exclusion and Confinement Effect

Selective removal of organic pollutants from surface water with high efficiency is crucial in water purification. Here, yolk-shell Co/C nanoreactors (YSCCNs) are facilely synthesized via pyrolysis of controllably etched ZIF-67 by tannic acid, and their degradation performance on multiple pollutants is demonstrated. To present the structure-performance relationship between the designed nanocatalyst and the selective removal of organic pollutants, bisphenol A (BPA) was selected as the targeted pollutant with coexistence of humus acid (HA). For comparison, solid and hollow ZIF-67 derived Co/C nanoparticles denoted as SCCNs and HCCNs, were also tested. The results show that YSCCNs exhibit enhanced BPA degradation rate of 0.32 min^-1, which is 23.1% and 45.4% higher than that of HCCNs and SCCNs in HA (10 ppm) system. The essential improvement can be ascribed to the synergetic effects from shell layer (size-exclusion) and core/shell (confinement effect). The degradation mechanism and pathway are further confirmed by radical quenching experiments and liquid chromatography-mass spectrograph (LC-MS), respectively. In addition, some influential factors, including reaction temperature, pH value, and peroxymonosulfate (PMS) dosage are investigated in detail. This work provides a possible way to selectively remove target contaminant from multiple pollutants in complex water system.

Saclike-silicon nanoparticles anchored in ZIF-8 derived spongy matrix as high-performance anode for lithium-ion batteries

The carbon layer with good electrical conductivity and outstanding mechanical stability are essential in designing high-performance silicon/carbon (Si/C) anodes to replace the commercial graphite in lithium-ion batteries (LIBs). In terms of solving the two inherent defects of poor conductivity and big volume change of silicon, we fabricate a spongy carbon matrix derived from ZIF-8 to anchor saclike silicon synthesized by molten salt magnesiothermic reduction method. This spongy matrix can anchor saclike silicon to provide a stable reaction interface and support fast electronic transmission. At the same time, buffer space in saclike Si nanoparticles and spongy matrix can synergistically accommodate the volume change of Si to maintain the integrity of the electrode. The resulting composite with a high Si content of 77.58% exhibits good capacities of 1448 mAh g^-1 at 2 A g^-1 and 848 mAh g^-1 at 4 A g^-1 after 500 cycles. High initial coulombic efficiency of 84% at 0.2 A g^-1 is also exhibited in the first three activation cycles. Therefore, this novel multifunctional N-doped spongy matrix can supply multifaceted benefits in accommodation of volumetric variation, enhancement of conductivity, and integrity of structure during cycling.

A metal-free and preconcentration-free method for non-enzymatic amperometric determination of pentachlorophenol using a ZIF-derived hollow carbon material

An enzyme-free, metal-free, and preconcentration-free electrochemical sensor for pentachlorophenol assay has been fabricated. The interface of the sensor is based on a hollow zeolitic imidazolate framework-derived mesoporous carbon material (denoted as HZC/SPCE). The sensor exhibits linear amperometric response upon pentachlorophenol at 0.82 V (vs. Ag/AgCl) in the concentration range 0.001 to 26.8 mg L^-1 (3.75 × 10^-8~1.006 × 10^-4 M) (R² = 0.997). The sensitivity of HZC/SPCE is 3.53 × 10² μA mM^-1 cm^-2 with a detection limit of 2.05 × 10^-9 M (S/N = 3) for pentachlorophenol. The method has been applied to the determination of pentachlorophenol in spiked food packaging samples with recoveries in the range 92.0 to 107.0%. Graphical abstract Schematic representation of the synthesis of hollow ZIFs-derived hollow carbon material. Free protons derived from tannic acid penetrated into ZIF-8 to destroy its solid framework and the outer parts covered by tannic acid were protected from further etching. After pyrolysis, the morphology of HZC remained similar to that of HZIF-8. Abbreviation: CTAB: hexadecyl trimethyl ammonium bromide; Melm: 2-methylimidazole; ZIF-8: zeolitic imidazolate framework-8; TA: tannic acid; HZIF-8: hollow zeolitic imidazolate framework-8; HZC: hollow zeolitic imidazolate frameworks (ZIFs)-derived mesoporous carbon material.

Capacitive deionization for wastewater treatment: Opportunities and challenges

Capacitive deionization (CDI) is an emerging method for removal of charged ionic species from aqueous solutions, based on electrostatic interactions between (mostly) inorganic ions and porous carbon electrodes. Inspection of recent publications related to CDI processes, revealed that the majority of the publications are related to the removal of salt (NaCl) from the water (desalination) or electrosorption processes. However, such a water desalination is only one process in the improvement of the quality water, it is interesting to review the literature in the context of CDI processes for other water treatment processes. Herein wastewater treatments are discussed. In this paper, we critically review the last publications that relate to capacitive deionization with wastewater treatments. Since wastewater treatments may involve broad aspects, we address in this review four specific water treatment processes that are thought to be connected with CDI processes: organic fouling of CDI cells, removal of heavy metals by CDI processes, removal of organic micropollutants with CDI processes and disinfection with CDI processes. We also evaluate herein the status of several research efforts in this area and suggest future directions.

Transformation of hollow ZnFe-ZIF-8 nanocrystals into hollow ZnFe–N/C electrocatalysts for the oxygen reduction reaction

A novel approach for the preparation of a highly active hollow ZnFe–N/C electrocatalyst for the ORR in an alkaline electrolyte was reported.

Frontiers of carbon materials as capacitive deionization electrodes

Carbon materials are widely used as capacitive deionization (CDI) electrodes due to their high specific surface area (SSA), superior conductivity, and better stability, including activated carbon, carbon aerogels, carbon nanotubes and graphene.

Sustainable Desalination by 3:1 Reduced Graphene Oxide/Titanium Dioxide Nanotubes (rGO/TiONTs) Composite via Capacitive Deionization at Different Sodium Chloride Concentrations

The capability of novel 3:1 reduced graphene oxide/titanium dioxide nanotubes (rGO/TiONTs) composite to desalinate using capacitive deionization (CDI) employing highly concentrated NaCl solutions was tested in this study. Parameters such as material wettability, electrosorption capacity, charge efficiency, energy consumption, and charge-discharge retention were tested at different NaCl initial concentrations—100 ppm, 2000 ppm, 15,000 ppm, and 30,000 ppm. The rGO/TiONTs composite showed good material wettability before and after CDI runs with its contact angles equal to 52.11° and 56.07°, respectively. Its two-hour electrosorption capacity during CDI at 30,000 ppm NaCl influent increased 1.34-fold compared to 100 ppm initial NaCl influent with energy consumption constant at 1.11 kWh per kg with NaCl removed. However, the percentage discharge (concentration-independent) at zero-voltage ranged from 4.9–7.27% only after 30 min of desorption. Repeated charge/discharge at different amperes showed that the slowest charging rate of 0.1 A·g⁻¹ had the highest charging time retention at 60% after 100 cycles. Increased concentration likewise increases charging time retention. With this consistent performance of a CDI system utilizing rGO/TiONTs composite, even at 30,000 ppm and 100 cycles, it can be a sustainable alternative desalination technology, especially if a low charging current with reverse voltage discharge is set for a longer operation.

Rational Design of Carbon Nanomaterials for Electrochemical Sodium Storage and Capture

Electrochemical sodium storage and capture are considered an attractive technology owing to the natural abundance, low cost, safety, and cleanness of sodium, and the higher efficiency of the electrochemical system compared to fossil-fuel-based counterparts. Considering that the sodium-ion chemistry often largely deviates from the lithium-based one despite the physical and chemical similarities, the architecture and chemical structure of electrode materials should be designed for highly efficient sodium storage and capture technologies. Here, the rational design in the structure and chemistry of carbon materials for sodium-ion batteries (SIBs), sodium-ion capacitors (SICs), and capacitive deionization (CDI) applications is comprehensively reviewed. Types and features of carbon materials are classified into ordered and disordered carbons as well as nanodimensional and nanoporous carbons, covering the effect of synthesis parameters on the carbon structure and chemistry. The sodium storage mechanism and performance of these carbon materials are correlated with the key structural/chemical factors, including the interlayer spacing, crystallite size, porous characteristics, micro/nanostructure, morphology, surface chemistry, heteroatom incorporation, and hybridization. Finally, perspectives on current impediment and future research directions into the development of practical SIBs, SICs, and CDI are also provided.

Electrochemical detection of superoxide anions in HeLa cells by using two enzyme-free sensors prepared from ZIF-8-derived carbon nanomaterials

Two kinds of carbon-based nanozymes were constructed from the same precursor of zeolitic imidazolate framework-8 (ZIF-8) for O₂^•- determination. Hollow carbon cubic nanomaterial (labelled as HCC) was obtained by chemically etching ZIF-8 with tannic acid and a subsequent calcination. A porous carbon cubic nanomaterial (labelled as PCC) was prepared by directly pyrolysis. Then HCC and PCC were immobilized on the surface of screen printed carbon electrodes (SPCE), fabricating HCC and PCC modified electrodes (denoted as HCC/SPCE and PCC/SPCE). HCC/SPCE, best operated at -0.5 V (vs. Ag/AgCl), has a sensitivity of 6.55 × 10² nA μM^-1 cm^-2 with a detection limit of 207 nM (at S/N = 3) for O₂^•- sensing. And PCC/SPCE, best operated at -0.4 V (vs. Ag/AgCl), exhibited a superior performance for O₂^•- detection with a sensitivity of 1.14 × 10³ nA μM^-1 cm^-2 and a low detection limit of 140 nM (at S/N = 3). The two sensors possess excellent reproducibility and stability. They were used to sense O₂^•- released from HeLa cells. Graphical abstract Illustration of the synthesis of the hollow carbon cubic nanomaterial (HCC) and of the porous carbon cubic nanomaterial (PCC), and the scheme for detection of superoxide anions in HeLa cell.

Carbon-mediated synthesis of shape-controllable manganese phosphate as nanozymes for modulation of superoxide anions in HeLa cells

Here we present a facile method to fabricate shape-controllable transition metal phosphates by using hollow carbon structures as substrates for superoxide sensing.

High-Performance Membrane Capacitive Deionization Based on Metal-Organic Framework-Derived Hierarchical Carbon Structures

Membrane capacitive deionization (MCDI) is a simple and highly energy efficient method to convert brackish water to clean water. In this work, a high-performance MCDI electrode architecture, which is composed of three-dimensional graphene networks and metal-organic frameworks (MOFs)-derived porous carbon rods, was prepared by a facile method. The obtained electrode material possesses not only the conducting networks for rapid electron transport but also the short diffusion length of ions, which exhibits excellent desalination performance with a high salt removal capacity, i.e., 37.6 mg g^-1 at 1.2 V in 1000 mg L^-1 NaCl solution. This strategy can be extended to other MOF-derived MCDI electrodes.