NiFe layered double hydroxide electrodeposited on Ni foam coated with reduced graphene oxide for high-performance supercapacitors

Mg doping of NiMn-LDH with a three-dimensional porous morphology for an efficient supercapacitor

As a promising supercapacitor electrode material, NiMn-LDH has attracted great attention due to its high theoretical capacity and easy preparation. However, the development and application of NiMn-LDH in supercapacitors are limited because of its poor cycling stability and low electrical conductivity. To solve these problems, a NiMnMg-LDH with a three-dimensional porous morphology has been successfully fabricated by doping with Mg to improve its electrochemical properties. Experimental results indicate that NiMnMg-LDH-7 delivers a specific capacitance of 1772 F g^-1 at a current density of 1 A g^-1. Moreover, it can still reach 1080 F g^-1 when the current density is increased 10 times, suggesting excellent rate capability. The asymmetric supercapacitor (ASC) NiMnMg-LDH-7//AC can provide a high energy density of 28 W h kg^-1 at a power density of 700 W kg^-1. Furthermore, the energy density can still reach 16 W h kg^-1 even if the power density is increased to close to 3500 W kg^-1. The capacity retention of this ASC device can reach 74% after 3000 cycles at a current density of 3 A g^-1. These excellent properties of NiMnMg-LDH can be attributed to the obvious improvement of its specific surface area and electrical conductivity owing to doping with the element magnesium. We believe that this work could provide a new idea for the preparation of high-performance electrode materials for supercapacitors.

CoFe-Layered Double Hydroxide Coupled with Pd Particles for Electrocatalytic Ethanol Oxidation

Electrocatalytic efficiency and stability have emerged as critical issues in the ethanol oxidation reaction (EOR) of direct ethanol fuel cells. In this paper, Pd/Co₁Fe₃-LDH/NF as an electrocatalyst for EOR was prepared by a two-step synthetic strategy. Metal-oxygen bonds formed between Pd nanoparticles and Co₁Fe₃-LDH/NF guaranteed structural stability and adequate surface-active site exposure. More importantly, the charge transfer of the formed Pd-O-Co(Fe) bridge could effectively modulate the electrical structure of hybrids, improving the facilitated absorption of OH^- radicals and oxidation of CO_ads. Benefiting from the interfacial interaction, exposed active sites, and structural stability, the observed specific activity for Pd/Co₁Fe₃-LDH/NF (17.46 mA cm^-2) was 97 and 73 times higher than those of commercial Pd/C (20%) (0.18 mA cm^-2) and Pt/C (20%) (0.24 mA cm^-2), respectively. Besides, the j_f/j_r ratio representing the resistance to catalyst poisoning was 1.92 in the Pd/Co₁Fe₃-LDH/NF catalytic system. These results provide insights into optimizing the electronic interaction between metals and the support of electrocatalysts for EOR.

Modulating the Surface Electronic Structure of Active Ni Sites by Engineering Hierarchical NiFe-LDH/CuS over Cu Foam as an Efficient Electrocatalyst for Water Splitting

Water electrolysis encounters a challenging problem in designing a highly efficient, long durable, non-noble metal-free electrocatalyst for both oxygen evolution reaction (OER) and hydrogen evolution reaction (HER). Here, in our work, a two-step hydrothermal reaction was performed to construct a hierarchal NiFe-layer double hydroxide (LDH)/CuS over copper foam for the overall water splitting reaction. While employed the same as an anode material, the designed heterostructure electrode NiFe-LDH/CuS/Cu exhibits excellent OER performance and it demands 249 mV overpotential to reach a current density of 50 mA cm^-2 with a lower Tafel slope value of 81.84 mV dec^-1. While as a cathode material, the NiFe-LDH/CuS/Cu shows superior HER performance and it demands just 28 mV of overpotential value to reach a current density of 10 mA cm^-2 and a lower Tafel slope value of 95.98 mV dec^-1. Hence, the NiFe-LDH/CuS/Cu outperforms the commercial Pt/C and RuO₂ in terms of activity in HER and OER, respectively. Moreover, when serving as both the cathode and anode catalysts in an electrolyzer for total water splitting, the synthesized electrode only needs a cell potential of 1.55 V versus RHE to reach a current density of 20 mA cm^-2 and long-term durability for 25 h in alkaline media. To study the interfacial electron transfer, Mott-Schottky experiments were performed, representing that the electron is transferred from n-type NiFe-LDH to p-type CuS as a result of creating the p-n junction in NiFe-LDH/CuS/Cu. The formation of this p-n junction allows the LDH layer to be more active toward the OH- adsorption and thereby could allow the OER or HER with a less energy input. This work affords another route to a cost effective, highly efficient catalyst toward producing clean energy across the globe.

Rational design of NiFe alloys for efficient electrochemical hydrogen evolution reaction: effects of Ni/Fe molar ratios

Developing and designing high-performance and stable NiFe electrodes for efficient hydrogen production are the greatest challenges in electrochemical water splitting. In this work, NiFe alloys with different Ni and Fe contents are prepared by a simple electrodeposition method using different molar ratios of Ni/Fe precursors (Ni/Fe; 1 : 3, 1 : 1 and 3 : 1). The obtained NiFe electrode with a molar ratio of 3 : 1 exhibited better electrocatalytic activity for the HER than the other NiFe electrodes with 1 : 3 and 1 : 1 molar ratios. The NiFe (Ni/Fe, 3 : 1) electrode required an overpotential of 133 mV to reach a current density of 10 mA cm⁻², which was much lower than those of NiFe with molar ratio of 1 : 3 (220 mV), and 1 : 1 (365 mV), respectively. Tafel slope analyses demonstrated that the HER mechanism of NiFe alloy coatings followed the Volmer reaction type. The superior electrocatalytic performance of the NiFe alloy for HER depending on precursor molar ratio of Ni/Fe was attributed to their composition in terms of Ni and Fe content, structure and surface morphology. Specifically, the electrodeposition of the NiFe alloy was obtained in a molar ratio Ni/Fe, 3 : 1, and induced the formation of NiFe layered double hydroxide (LDH) with a nanosheet-array structure. The high electrocatalytic activity of NiFe LDH (Ni/Fe, 3 : 1) confirmed the critical influence of Ni and Fe contents in the alloy resulting in an increase the active surface on the surfaces, which is most likely explained by the higher surface roughness and the low crystallinity structure of NiFe nanosheet-array, supported by ECSA measurement, XRD, SEM and AFM analyses. The present strategy may open an avenue for developing cost-effective, stable and high-performance electrocatalysts as advanced electrodes for large-scale water splitting.

Developing and designing high-performance and stable NiFe electrodes for efficient hydrogen production in alkaline medium.

Preparation of a Honeycomb-like FeNi(OH/P) Nanosheet Array as a High-Performance Cathode for Hybrid Supercapacitors

Polymetallic transition metal phosphides (TMPs) exhibit quasi-metallic properties and a high electrical conductivity, making them attractive for high-performance hybrid supercapacitors (HSCs). Herein, a nanohoneycomb (NHC)-like FeNi layered double hydroxide (LDH) array was grown in situ on 3D current collector nickel foam (NF), which is also the nickel source during the hydrothermal process. By adjusting the amount of NaH2PO2, an incomplete phosphated FeNi(OH/P) nanosheet array was obtained. The optimized FeNi(OH/P) nanosheet array exhibited a high capacity up to 3.6 C cm−2 (408.3 mAh g−1) and an excellent long-term cycle performance (72.0% after 10,000 cycles), which was much better than FeNi LDH’s precursor. In addition, the hybrid supercapacitor (HSC) assembled with FeNi(OH/P) (cathode) and polypyrrole (PPy/C, anode) achieved an ultra-high energy density of 45 W h kg−1 at a power density of 581 W kg−1 and an excellent cycle stability (118.5%, 2000 cycles), indicating its great potential as an HSC with a high electrochemical performance.

Metal-Organic Framework-Derived Hollow CoSx Nanoarray Coupled with NiFe Layered Double Hydroxides as Efficient Bifunctional Electrocatalyst for Overall Water Splitting

For effective hydrogen production by water splitting, it is essential to develop earth-abundant, highly efficient, and durable electrocatalysts. Herein, the authors report a bifunctional electrocatalyst composed of hollow CoS_x and Ni-Fe based layered double hydroxide (NiFe LDH) nanosheets for efficient overall water splitting (OWS). The optimized heterostructure is obtained by the electrodeposition of NiFe LDH nanosheets on metal-organic framework-derived hollow CoS_x nanoarrays, which are supported on nickel foam (H-CoS_x @NiFe LDH/NF). The unique structure of the hybrid material not only provides ample active sites, but also facilitates electrolyte penetration and gas release during the reactions. Additionally, the strong coupling and synergy between the hydrogen evolution reaction (HER) active CoS_x and the oxygen evolution reaction (OER) active NiFe LDH gives rise to the excellent bifunctional properties. Consequently, H-CoS_x @NiFe LDH/NF exhibits remarkable HER and OER activities with overpotentials of 95 and 250 mV, respectively at 10 mA cm^-2 in 1.0 M KOH. Even at 1.0 A cm^-2 , the electrode requires small overpotentials of 375 mV (for HER) and 418 mV (for OER), respectively. An electrolyzer based on H-CoS_x @NiFe LDH/NF demonstrates a low cell voltage of 1.98 V at a current density of 300 mA cm^-2 and good durability for 100 h in OWS application.

3D-printed NiFe-layered double hydroxide pyramid electrodes for enhanced electrocatalytic oxygen evolution reaction

Electrochemical water splitting has been considered one of the most promising methods of hydrogen production, which does not cause environmental pollution or greenhouse gas emissions. Oxygen evolution reaction (OER) is a significant step for highly efficient water splitting because OER involves the four electron transfer, overcoming the associated energy barrier that demands a potential greater than that required by hydrogen evolution reaction. Therefore, an OER electrocatalyst with large surface area and high conductivity is needed to increase the OER activity. In this work, we demonstrated an effective strategy to produce a highly active three-dimensional (3D)-printed NiFe-layered double hydroxide (LDH) pyramid electrode for OER using a three-step method, which involves direct-ink-writing of a graphene pyramid array and electrodeposition of a copper conducive layer and NiFe-LDH electrocatalyst layer on printed pyramids. The 3D pyramid structures with NiFe-LDH electrocatalyst layers increased the surface area and the active sites of the electrode and improved the OER activity. The overpotential (η) and exchange current density (i₀) of the NiFe-LDH pyramid electrode were further improved compared to that of the NiFe-LDH deposited Cu (NiFe-LDH/Cu) foil electrode with the same base area. The 3D-printed NiFe-LDH electrode also exhibited excellent durability without potential decay for 60 h. Our 3D printing strategy provides an effective approach for the fabrication of highly active, stable, and low-cost OER electrocatalyst electrodes.

Sandwich-like NiCo-LDH/rGO with Rich Mesopores and High Charge Transfer Capability for Flexible Supercapacitors

Layered double metal hydroxides (LDHs) have been widely used in the energy storage field due to adjustable composition and interlayer spacing. However, easy to agglomerate, poor electrical conductivity, and large...

Synthesis of CNTs/CoNiFe-LDH Nanocomposite with High Specific Surface Area for Asymmetric Supercapacitor

Ternary layered double hydroxide (LDH) materials have shown promising application in hybrid supercapacitors. However, the low electrical conductivity of LDHs is still a restriction to their performance. Herein, carbon nanotubes/cobalt-nickel-iron LDH (CNTs/CoNiFe-LDH) hybrid material was prepared by a one-step hydrothermal approach for the first time. The presence of CNTs improved the conductivity and surface area of the electrode, leading to an enhanced electrochemical performance. The CNTs/CoNiFe-LDH hybrid electrode exhibited high specific capacity 170.6 mAh g-1 at a current density of 1 A g-1, with a capacity retention of 75% at 10 A g-1. CNTs/CoNiFe-LDH//AC asymmetric supercapacitor (ASC) was also assembled, which had high specific capacitance (96.1 F g-1 at the current density of 1 A g-1), good cycling stability (85.0% after 3000 cycles at 15 A g-1) and high energy density (29.9 W h kg-1 at the power density of 750.5 W kg-1). Therefore, the CNTs/CoNiFe-LDH material could be used for hybrid supercapacitor electrodes.

Slight Zinc Doping by an Ultrafast Electrodeposition Process Boosts the Cycling Performance of Layered Double Hydroxides for Ultralong-Life-Span Supercapacitors

Layered double hydroxides (LDHs) have attracted much attention in supercapacitors because of the high specific surface area and theoretical capacitance. However, the bad cycling stability has always been their Achilles' heel that restrains their further application. In this paper, a small amount of unactive and single-valence element zinc, which has no contribution to the capacitance of electrodes, was first doped into NiCo-LDHs through two consecutive electrodeposition processes only within 30 min. With a polyaniline (PANI) nanolayer as the interlayer, an ultrathin NiCoZn-LDH nanoplate network was well-anchored on the carbon cloth surface. The slight Zn²⁺ doping dramatically enhanced the cycling performance of LDHs with little capacitance decay. Zn²⁺ doping enhanced the cyclic structural stability of NiCoZn-LDHs, while the PANI layer strengthened the interface interaction between LDHs and the current collector. By controlling the doping content of Zn²⁺ at 2.9%, the composite electrode achieved the best performance with a high specific capacitance of 1749 F g^-1 and an ultralong life span with 89% capacitance retention after 40,000 charge-discharge cycles. This work offers a novel strategy to fast build LDH-based supercapacitors with both high specific capacitance and cycling performance.

One-step facile synthesis of nickel-chromium layered double hydroxide nanoflakes for high-performance supercapacitors

Rational design and synthesis of efficient electrodes with pronounced energy storage properties are crucial for supercapacitors. Herein, we report thin NiCr-layered double hydroxide nanoflakes (NiCr-LDNs) for a high-performance supercapacitor. These fabricated NiCr-LDNs, with various Ni2+/Cr3+ ratios, are one-step controllably synthesized through ultrasonication coupled with mechanical agitation, without hydrothermal treatment or extra exfoliation using organic solvents. Through comparison of different Ni2+/Cr3+ ratios, the Ni2Cr1-LDNs with a 4.7 nm thickness exhibited a superb capacitance performance of 1525 F g-1 at 2 A g-1, which is competitive with most previously reported layered double hydroxide (LDH)-based electrodes. These thin nanoflake structures have the potential to reduce the energy barrier and enhance the capture ability of electrolyte ions. Besides, an asymmetric supercapacitor (ASC) assembled using Ni2Cr1-LDNs achieved a remarkable energy density of 55.22 W h kg-1 at a power density of 400 W kg-1 and maintained high specific capacitance (over 81%), even after 5000 cycles. This work offers an efficient and facile route to fabricating LDH nanoflakes for boosting energy storage capabilities.

Recent Progress in Two-Dimensional Layered Double Hydroxides and Their Derivatives for Supercapacitors

High-performance supercapacitors have attracted great attention due to their high power, fast charging/discharging, long lifetime, and high safety. However, the generally low energy density and overall device performance of supercapacitors limit their applications. In recent years, the design of rational electrode materials has proven to be an effective pathway to improve the capacitive performances of supercapacitors. Layered double hydroxides (LDHs), have shown great potential in new-generation supercapacitors, due to their unique two-dimensional layered structures with a high surface area and tunable composition of the host layers and intercalation species. Herein, recent progress in LDH-based, LDH-derived, and composite-type electrode materials targeted for applications in supercapacitors, by tuning the chemical/metal composition, growth morphology, architectures, and device integration, is reviewed. The complicated relationships between the composition, morphology, structure, and capacitive performance are presented. A brief projection is given for the challenges and perspectives of LDHs for energy research.

Growth of NiMn layered double hydroxides on nanopyramidal BiVO4 photoanode for enhanced photoelectrochemical performance

Photoelectrochemical water oxidation for hydrogen generation via utilizing sunlight is considered a very promising pathway for generating sustainable energy in an environmental manner. Here, a composite photoanode, consisting of nanopyramidal BiVO₄ arrays and one layered double hydroxide (NiMn-LDH) was designed and fabricated via a facile route. The obtained BiVO₄/NiMn-LDH composite photoelectrode presented a significant enhancement in the photoelectrochemical (PEC) current density, conversion efficiency and stability for solar water oxidation. With 2D NiMn-LDH decoration, an obvious cathodic shift of ∼480 mV in the onset potential can be observed, and more than two times enhancement in photocurrent performance is achieved. The improvement in photoelectrochemical activity for BiVO₄/NiMn-LDH composite photoanode can be attributed to the enhanced water-oxidation kinetics leading to the efficient separation, transfer and collection of charge carriers at the photoanode/electrolyte interface. The result demonstrates NiMn-LDH represents one of the active oxygen evolution catalysts (OECs) to improve the PEC activity of metal oxide photoanode.

Value-Added Formate Production from Selective Methanol Oxidation as Anodic Reaction to Enhance Electrochemical Hydrogen Cogeneration

Electrolytic overall water splitting is a promising approach to produce H₂ , but its efficiency is severely limited by the sluggish kinetics of the oxygen evolution reaction (OER) and the low activity of current electrocatalysts. To solve these problems, in addition to the development of efficient precious-metal catalysts, an effective strategy is proposed to replace the OER by the selective methanol oxidation reaction. Ni-Co hydroxide [Ni_x Co_1-x (OH)₂ ] nanoarrays were obtained through a facile hydrothermal treatment as the bifunctional electrocatalysts for the co-electrolysis of methanol/water to produce H₂ and value-added formate simultaneously. The electrocatalyst could catalyze selective methanol oxidation (≈1.32 V) with a significantly lower energy consumption (≈0.2 V less) than OER. Importantly, methanol was transformed exclusively to value-added formate with a high Faradaic efficiency (selectivity) close to 100 %. Specifically, a cell voltage of only approximately 1.5 V was required to generate a current density of 10 mA cm^-2 . Furthermore, the Ni_0.33 Co_0.67 (OH)₂ /Ni foam nanoneedle arrays presented an outstanding stability for overall co-electrolysis.

Electro-deposition of nickel–iron nanoparticles on flower-like MnCo2O4 nanowires as an efficient bifunctional electrocatalyst for overall water splitting

The obtained NiFe–MnCo₂O₄/NFF electrode exhibited superior electrocatalytic performance and extraordinary durability for the OER, HER, and overall water splitting.

Nanoneedle-decorated NiCo-layered double hydroxide microspheres tuned as high-efficiency electrodes for pseudocapacitors

Nanoneedle-decorated flower-like NiCo-LDH microspheres are tuned by varying the amounts of NH₄F, providing tunable electrochemical performance for their use as electrodes for pseudocapacitors.