Improved electrochemical detection of metals in biological samples using 3D-printed electrode: Chemical/electrochemical treatment exposes carbon-black conductive sites

Optimizing the Construction and Activation of 3D-Printed Electrochemical Sensors: An Experimental Design Approach for Simultaneous Electroanalysis of Paracetamol and Caffeine

This work presents an optimization of the construction, treatment, and activation of 3D-printed electrochemical sensors (E-3D). For this, was used a 23-full factorial design examining three key variables at two levels: electrode height, electrode diameter, and printing speed. Moreover, it evaluates various physical, chemical, and electrochemical methods to treat and activate the E-3D surface. The techniques of electrochemical impedance spectroscopy and cyclic voltammetry (CV) shows that the sequential physical, chemical, and electrochemical treatments lead to the highest treatment efficiency and activation. Raman spectroscopy and atomic force microscopy characterize untreated and treated E-3D sensor surfaces. The optimal treatment and activation methodology was applied to the electroanalysis of paracetamol (PAR) and caffeine (CAF) simultaneously using CV and differential pulse anodic stripping voltammetry (DPASV). DPASV measurements reveal limits of detection of 0.44 and 0.58 μmol L-1 in a 0.5 mol L-1 H2SO4 medium for PAR and CAF, respectively, with the treated and activated E-3D sensor. The principal achievement of this work was emphasizing the critical role of surface treatment and activation in enhancing the performance of the developed electrodes, thereby advancing technological applications of 3D-printed electrochemical sensors.

Portable Atmospheric Air Plasma Jet Pen for the Surface Treatment of Three-Dimensionally (3D)-Printed Electrodes

Three-dimensional (3D) printing is an emerging technology to develop devices on a large scale with potential application for electroanalysis. However, 3D-printed electrodes, in their native form, provide poor electrochemical response due to the presence of a high percentage of thermoplastic polymer in the conductive filaments. Therefore, surface treatments are usually required to remove the nonconductive material from the 3D-printed electrode surfaces, providing a dramatic improvement in the electroanalytical performance. However, these procedures are time-consuming, require bulky equipment, or even involve non-eco-friendly protocols. Herein, we demonstrated that portable and low-cost atmospheric air plasma jet pens can be used to activate electrodes additively manufactured using a commercial poly(lactic acid) filament containing carbon black as conductive filler, improving the electrochemical activity. Remarkable electrochemical results were obtained (voltammetric profile) using [Fe(CN)6]3-/4-, dopamine and [Ru(NH3)6]2+/3+ as redox probes. Microscopic, spectroscopic, and electrochemical techniques revealed that the air-plasma jet pen removes the excess PLA on the 3D-printed electrode surface, exposing the conductive carbon black particles and increasing the surface area. The performance of the treated electrode was evaluated by the quantification of capsaicin in pepper sauce samples, with a limit of detection of 3 nM, suitable for analysis of food samples. Recovery values from 94% to 101% were obtained for the analysis of spiked samples. The new treatment generated by a plasma jet pen is an alternative approach to improve the electrochemical activity of 3D-printed electrodes that present sluggish kinetics with great advantages over previous protocols, including low-cost, short time of treatment (2 min), environmentally friendly protocol (reagentless), and portability (hand-held pen).

A miniaturized additive-manufactured carbon black/PLA electrochemical sensor for pharmaceuticals detection

Additive manufacturing is a technique that allows the construction of prototypes and has evolved a lot in the last 20 years, innovating industrial fabrication processes in several areas. In chemistry, additive manufacturing has been used in several functionalities, such as microfluidic analytical devices, energy storage devices, and electrochemical sensors. Theophylline and paracetamol are important pharmaceutical drugs where overdosing can cause adverse effects, such as tachycardia, seizures, and even renal failure. Therefore, this paper aims at the development of miniaturized electrochemical sensors using 3D printing and polylactic acid-based conductive carbon black commercial filament for theophylline and paracetamol detection. Electrochemical characterizations of the proposed sensor were performed to prove the functionality of the device. Morphological characterizations were carried out, in which chemical treatment could change the surface structure, causing the improvement of the analytical signal. Thus, the detection of theophylline at a linear range of 5.00-150 μmol L-1 with a limit of detection of 1.2 μmol L-1 was attained, and the detection of paracetamol at a linear range of 1.00-200 μmol L-1 with a limit of detection of 0.370 μmol L-1 was obtained, demonstrating the proposed sensor effectively detected pharmaceutical drugs.

Spark-Discharge-Activated 3D-Printed Electrochemical Sensors

3D printing technology is a tremendously powerful technology to fabricate electrochemical sensing devices. However, current conductive filaments are not aimed at electrochemical applications and therefore require intense activation protocols to unleash a suitable electrochemical performance. Current activation methods based on (electro)chemical activation (using strong alkaline solutions and organic solvents and/or electrochemical treatments) or combined approaches are time-consuming and require hazardous chemicals and dedicated operator intervention. Here, pioneering spark-discharge-activated 3D-printed electrodes were developed and characterized, and it was demonstrated that their electrochemical performance was greatly improved by the effective removal of the thermoplastic support polylactic acid (PLA) as well as the formation of sponge-like and low-dimensional carbon nanostructures. This reagent-free approach consists of a direct, fast, and automatized spark discharge between the 3D-electrode and the respective graphite pencil electrode tip using a high-voltage power supply. Activated electrodes were challenged toward the simultaneous voltammetric determination of dopamine (DP) and serotonin (5-HT) in cell culture media. Spark discharge has been demonstrated as a promising approach for conductive filament activation as it is a fast, green (0.94 GREEnness Metric Approach), and automatized procedure that can be integrated into the 3D printing pipeline.

Microwave-Induced Processing of Free-Standing 3D Printouts: An Effortless Route to High-Redox Kinetics in Electroanalysis

3D-printable composites have become an attractive option used for the design and manufacture of electrochemical sensors. However, to ensure proper charge-transfer kinetics at the electrode/electrolyte interface, activation is often required, with this step consisting of polymer removal to reveal the conductive nanofiller. In this work, we present a novel effective method for the activation of composites consisting of poly(lactic acid) filled with carbon black (CB-PLA) using microwave radiation. A microwave synthesizer used in chemical laboratories (CEM, Matthews, NC, USA) was used for this purpose, establishing that the appropriate activation time for CB-PLA electrodes is 15 min at 70 °C with a microwave power of 100 W. However, the usefulness of an 80 W kitchen microwave oven is also presented for the first time and discussed as a more sustainable approach to CB-PLA electrode activation. It has been established that 10 min in a kitchen microwave oven is adequate to activate the electrode. The electrochemical properties of the microwave-activated electrodes were determined by electrochemical techniques, and their topography was characterized using scanning electron microscopy (SEM), Raman spectroscopy, and contact-angle measurements. This study confirms that during microwave activation, PLAs decompose to uncover the conductive carbon-black filler. We deliver a proof-of-concept of the utility of kitchen microwave-oven activation of a 3D-printed, free-standing electrochemical cell (FSEC) in paracetamol electroanalysis in aqueous electrolyte solution. We established satisfactory limits of linearity for paracetamol detection using voltammetry, ranging from 1.9 μM to 1 mM, with a detection limit (LOD) of 1.31 μM.

Optimised graphite/carbon black loading of recycled PLA for the production of low-cost conductive filament and its application to the detection of β-estradiol in environmental samples

The production, optimisation, physicochemical, and electroanalytical characterisation of a low-cost electrically conductive additive manufacturing filament made with recycled poly(lactic acid) (rPLA), castor oil, carbon black, and graphite (CB-G/PLA) is reported. Through optimising the carbon black and graphite loading, the best ratio for conductivity, low material cost, and printability was found to be 60% carbon black to 40% graphite. The maximum composition within the rPLA with 10 wt% castor oil was found to be an overall nanocarbon loading of 35 wt% which produced a price of less than £0.01 per electrode whilst still offering excellent low-temperature flexibility and reproducible printing. The additive manufactured electrodes produced from this filament offered excellent electrochemical performance, with a heterogeneous electron (charge) transfer rate constant, k0 calculated to be (2.6 ± 0.1) × 10-3 cm s-1 compared to (0.46 ± 0.03) × 10-3 cm s-1 for the commercial PLA benchmark. The additive manufactured electrodes were applied to the determination of β-estradiol, achieving a sensitivity of 400 nA µM-1, a limit of quantification of 70 nM, and a limit of detection of 21 nM, which compared excellently to other reports in the literature. The system was then applied to the detection of ß-estradiol within four real water samples, including tap, bottled, river, and lake water, where recoveries between 95 and 109% were obtained. Due to the ability to create high-performance filament at a low material cost (£0.06 per gram) and through the use of more sustainable materials such as recycled polymers, bio-based plasticisers, and naturally occurring graphite, additive manufacturing will have a permanent place within the electroanalysis arsenal in the future.

A review on the surface modification of materials for 3D-printed diagnostic devices

Three-dimensional (3D) printing in tissue engineering and biosensing of analytes by using biocompatible materials or modifying surface structures is an upcoming area of study. This review discusses three common surface modification techniques, viz. alkaline hydrolysis, UV light photografting, and plasma treatment. Alkaline hydrolysis involves the reaction of an alkaline solution with the surface of a material, causing the surface to develop carboxyl and hydroxyl groups. This technique can enhance the biocompatibility, surface wettability, adhesion, printability, and dyeability of materials, such as acrylonitrile butadiene styrene (ABS), polycarbonate, and polylactic acid (PLA). This review also mentions details about some of the surface-modified 3D-printed diagnostic devices. Although most of the devices are modified using chemical processes, there are always multiple techniques involved while designing a diagnostic device. We have, therefore, mentioned some of the devices based on the materials used instead of categorising them as per modification techniques. 3D printing helps in the design of sophisticated shapes and structures using multiple materials. They can, therefore be used even in the design of microfluidic devices that are very useful for biosensing. We have also mentioned a few materials for printing microfluidic devices.

Solvent-activated 3D-printed electrodes and their electroanalytical potential

This work is a comprehensive study describing the optimization of the solvent-activated carbon-based 3D printed electrodes. Three different conductive filaments were used for the preparation of 3D-printed electrodes. Electrodes treatment with organic solvents, electrochemical characterization, and finally electroanalytical application was performed in a dedicated polyamide-based cell also created using 3D printing. We have investigated the effect of the used solvent (acetone, dichloromethane, dichloroethane, acetonitrile, and tetrahydrofuran), time of activation (from immersion up to 3600 s), and the type of commercially available filament (three different options were studied, each being a formulation of a polylactic acid and conductive carbon material). We have obtained and analysed a significant amount of collected data which cover the solvent-activated carbon-based electrodes surface wettability, microscopic insights into the surface topography analysed with scanning electron microscopy and atomic force microscopy, and finally voltammetric evaluation of the obtained carbon electrodes electrochemical response. All data are tabulated, discussed, and compared to finally provide the superior activation procedure. The electroanalytical performance of the chosen electrode is discussed based on the voltammetric detection of ferrocenemethanol.

Conductive Additive Manufactured Acrylonitrile Butadiene Styrene Filaments: Statistical Approach to Mechanical and Electrical Behaviors

Additive manufacturing is a process in which digital three-dimensional (3D) design data are used to build a component in layers by accumulating materials. There are many materials used in additive manufacturing technology. The most basic features that distinguish these materials are their strength and electrical behavior. They can be strong or flexible, resistant to abrasion, depending on the application used. Recently, 3D printing filament and polymeric composite materials combined with carbon nanostructures with electrical conductivity have been used. In this study, acrylonitrile butadiene styrene (ABS), a carbon black-filled conductive material with high strength and hardness, was preferred. The aim in this study is to focus on the mechanical and electrical behavior of the material processed in filament form. Fabrication of samples was done using a fused deposition modeling-based printer that controls filament orientation. Different experimental studies were conducted: (1) mechanical tests to determine the maximum tensile strength values of the samples; and (2) electrical tests to analyze the electrical resistances of the samples. In the design of the first experiment, infill volume, layer height, infill type, and printing direction were determined as factors affecting strength. In the design of the second experiment, the length, nozzle temperature, and measurement temperature were determined as the factors affecting the electrical resistance. Statistical analysis of the measured data was performed to evaluate the overall result of the experiments. Finally, a prediction model of real-time tensile strength and resistance values was created using machine learning algorithms. These algorithms are Gaussian Process Regression and Support Vector Machine. The results confirmed the known linear dependence of electrical resistance on the length of the 3D-printed conductive ABS samples and showed how changing the fabrication settings affected the strength values.

Spectroelectrochemical sensing of reaction intermediates and products in an affordable fully 3D printed device

Recent advances in fused deposition modelling 3D printing (FDM 3DP) and synthesis of printable electrically conductive materials enabled the manufacture of customized electrodes and electrochemical devices by this technique. The past couple of years have seen a boom in applying approaches of FDM 3DP in the realm of spectroelectrochemistry (SEC). Despite significant progress, reported designs of SEC devices still rely on conventionally manufactured optical components such as quartz windows and cuvettes. To bridge this technological gap, in this work we apply bi-material FDM 3DP combining electrically conductive and optically translucent filaments to manufacture working electrodes and cells, constituting a fully integrated microfluidic platform for transmission absorption UV-Vis SEC measurements. The cell design enables de-aeration of samples and their convenient handling and analysis. Employing cyclic voltammetric measurements with ruthenium(III) acetylacetonate, ethylviologen dibromide and ferrocenemethanol redox-active probes as model analytes, we demonstrate that the presented platform allows SEC sensing of reactants, intermediates and products of charge transfer reactions, including the inspection of their long-term stability. Approaches developed and presented in this work pave the way for manufacturing customized SEC devices with dramatically reduced costs compared to currently available commercial platforms.

Electrochemical Determination of the Drug Colchicine in Pharmaceutical and Βiological Samples Using a 3D-Printed Device

In this work, a simple, fast, and sensitive voltammetric method for the trace determination of the alkaloid drug colchicine (Colc) using a 3D-printed device is described. The electrochemical method was based on the adsorptive accumulation of the drug at a carbon-black polylactic acid (CB/PLA) working electrode, followed by voltammetric determination of the accumulated species. The plastic sensor was printed in a single step by a low-cost dual extruder 3D-printer and featured three CB/PLA electrodes (serving as working, reference, and counter electrodes) and a holder, printed from a non-conductive PLA filament. The electrochemical parameters that affected the response of the device towards Colc determination, such as accumulation time and potential, solution pH, and other variables, were optimized. Under the selected conditions, the oxidation current of Colc was proportional to the concentration of Colc, and its quantification was conducted in the concentration range of 0.6-2.2 μmol L^-1 with a limit of detection of 0.11 μmol L^-1 in phosphate buffer (pH 7.0). Both within-device and between-device reproducibility were lower than 9%, revealing satisfactory operational and fabrication reproducibility. Furthermore, the 3D-printed device was employed for the voltammetric determination of Colc in pharmaceutical tablets and in human urine with satisfactory results, justifying its suitability for low-cost routine analysis of Colc.

Selective determination of cadmium and lead ions in different food samples by poly (riboflavin)/carbon black-modified glassy carbon electrode

In this research, a poly (riboflavin)/carbon black-modified glassy carbon electrode (PRF/CB/GCE) is introduced as a novel electrochemical sensor toward Cd²⁺ and Pb²⁺ simultaneous measurement in presence of bismuth ions, applying differential pulse anodic stripping voltammetry (DPASV). Regarding the optimized conditions, the linear ranges were achieved from 0.5 to 600 nM for Cd²⁺ and Pb²⁺. The detection limit (LOD) was found to be 0.16 nM for Cd²⁺ and 0.13 nM for Pb²⁺. In order to perform the technique in real application, the proposed electrode was used to simultaneously detect ions in rice, honey, and vegetable samples with satisfactory recoveries - indicating that the sensor possesses good practicability to determine Cd²⁺ and Pb²⁺. Moreover, an atomic absorption spectrometry (AAS) was used in order to detect the concentration of ions as a reference technique in rice, honey, and vegetable samples.

Graphene-based 3D-Printed nanocomposite bioelectronics for monitoring breast cancer cell adhesion

This work examines the suitability of graphene-based 3D-printed nanocomposite bioelectronics as innovative systems to in situ monitor and evaluate both breast cancer cell adhesion and the chemosensitivity of anti-cancer drugs. With this aim, 3D-printed nanocomposite graphene electrodes (3D-nGEs) -made of a commercially available graphene/polylactic acid filament- have been covalently biofunctionalized with an extracellular matrix protein (i.e., fibronectin) by exploiting the carbon reactivity of 3D-nGEs. The specificity and selectivity of the developed electrochemical system to monitor breast cancer cell adhesion has been tested via electrochemical impedance spectroscopy (EIS). Importantly, the resulting 3D-printed bioelectronic system displayed excellent accuracy for the rapid screening of anti-cancer drugs, which exactly corresponded with the results achieved by the standard optical method, while having the advantage of employing a label-free approach. In light of the current state-of-the-art in the field, this proof-of-concept connects electronics to biological systems within 3D printing technology, providing the bases for the sustainable and cost-effective manufacturing of graphene-based 3D-printed nanocomposite bioelectronics to simulate in vivo microenvironments using in situ and real time electronic output signals.

3D printing for customized carbon electrodes

Traditional carbon electrodes are made of glassy carbon or carbon fibers and have limited shapes. 3D printing offers many advantages for manufacturing carbon electrodes, such as complete customization of the shape and the ability to fabricate devices and electrodes simultaneously. Additive manufacturing is the most common 3D printing method, where carbon materials are added to the material to make it conductive, and treatments applied to enhance electrochemical activity. A newer form of 3D printing is 2-photon lithography, where electrodes are printed in photoresist via laser lithography and then annealed to carbon by pyrolysis. Applications of 3D printed carbon electrodes include nanoelectrode measurements of neurotransmitters, arrays of biosensors, and integrated electrodes in microfluidic devices.

3D printed electronics with nanomaterials

A large variety of printing, deposition and writing techniques have been incorporated to fabricate electronic devices in the last decades. This approach, printed electronics, has gained great interest in research and practical applications and is successfully fuelling the growth in materials science and technology. On the other hand, a new player is emerging, additive manufacturing, called 3D printing, introducing a new capability to create geometrically complex constructs with low cost and minimal material waste. Having such tremendous technology in our hands, it was just a matter of time to combine advances of printed electronics technology for the fabrication of unique 3D structural electronics. Nanomaterial patterning with additive manufacturing techniques can enable harnessing their nanoscale properties and the fabrication of active structures with unique electrical, mechanical, optical, thermal, magnetic and biological properties. In this paper, we will briefly review the properties of selected nanomaterials suitable for electronic applications and look closer at the current achievements in the synergistic integration of nanomaterials with additive manufacturing technologies to fabricate 3D printed structural electronics. The focus is fixed strictly on techniques allowing as much as possible fabrication of spatial 3D objects, or at least conformal ones on 3D printed substrates, while only selected techniques are adaptable for 3D printing of electronics. Advances in the fabrication of conductive paths and circuits, passive components, antennas, active and photonic components, energy devices, microelectromechanical systems and sensors are presented. Finally, perspectives for development with new nanomaterials, multimaterial and hybrid techniques, bioelectronics, integration with discrete components and 4D-printing are briefly discussed.

Three-Dimensional-Printed Electrochemical Multiwell Plates for Monitoring Food Intolerance from Intestinal Organoids

Common symptoms of food intolerance are caused by chemical components within food that have a pharmacological activity to alter the motility of the gastrointestinal tract. Food intolerance is difficult to diagnose as it requires a long-term process of eliminating foods that are responsible for gastrointestinal symptoms. Enterochromaffin (EC) cells are key intestinal epithelium cells that respond to luminal chemical stimulants by releasing 5-HT. Changes in 5-HT levels have been shown to directly alter the motility of the intestinal tract. Therefore, a rapid approach for monitoring the impact of chemicals in food components on 5-HT levels can provide a personalized insight into food intolerance and help stratify diets. Within this study, we developed a three-dimensional (3D)-printed electrochemical multiwell plate to determine changes in 5-HT levels from intestinal organoids that were exposed to varying chemical components found in food. The carbon black/poly-lactic acid (CB/PLA) electrodes had a linear range in physiological concentrations of 5-HT (0.1-2 μM) with a limit of detection of 0.07 μM. The electrodes were stable for monitoring 5-HT overflow from intestinal organoids. Using the electrochemical multiwell plate containing intestinal organoids, increases in 5-HT were observed in the presence of 0.1 mM cinnamaldehyde and 10 mM quercetin but reduction in 5-HT levels was observed in 1 mM sorbitol when compared to control. These changes in the presence of chemicals commonly found in food were verified with ex vivo ileum tissue measurements using chromatography and amperometry with boron-doped diamond electrodes. Overall, our 3D electrochemical multiwell plate measurements with intestinal organoids highlight an approach that can be a high-throughput platform technology for rapid screening of food intolerance to provide personalized nutritional diet.

Carbon Black Integrated Polylactic Acid Electrodes Obtained by Fused Deposition Modeling: A Powerful Tool for Sensing of Sulfanilamide Residues in Honey Samples

Sulfanilamide (SFL) is used to prevent infections in honeybees. However, many regulatory agencies prohibit or establish maximum levels of SFL residues in honey samples. Hence, we developed a low-cost and portable electrochemical method for SFL detection using a disposable device produced through 3D printing technology. In the proposed approach, the working electrode was printed using a conductive filament based on carbon black and polylactic acid and it was associated with square wave voltammetry (SWV). Under optimized SWV parameters, linear concentration ranges (1-10 μmol L^-1 and 12.5-35.0 μmol L^-1), a detection limit of 0.26 μmol L^-1 (0.05 mg L^-1), and suitable RSD values (2.4% for inter-electrode; n = 3) were achieved. The developed method was selective in relation to other antibiotics applied in honey samples, requiring only dilution in the electrolyte. The recovery values (85-120%) obtained by SWV were statistically similar (95% confidence level) to those obtained by HPLC, attesting to the accuracy of the analysis and the absence of matrix interference.

Multiple Reprocessing of Conductive PLA 3D-Printing Filament: Rheology, Morphology, Thermal and Electrochemical Properties Assessment

Additive manufacturing technologies are gaining more and more attention, resulting in the development or modification of 3D printing techniques and dedicated materials. On the other hand, economic and ecological aspects force the industry to develop material recycling strategies. In this work, the multiple reprocessing of a commercially available PLA conductive composite with carbon black filler, dedicated to 3D printing, was investigated. The effects of extrusion temperature (190 °C and 200 °C) and reprocessing steps (1-5 steps) on the rheology, morphology, thermal and electrochemical properties of the conductive PLA 3D-printing filament were evaluated. The results showed deterioration of the thermal stability and material strength, as well as the influence of reprocessing on the melting point, which increases after initial melting. The electronic conduction mechanism of the composite depends on the percolation paths and it is also affected by the multiple processing. The reversibility of the [Fe(CN)₆]^3-/4- redox process diminishes with a higher degradation level of the conductive PLA. Importantly, the material fluidity was too high after the multiple reprocessing, which should be considered and suitably corrected during CB-PLA application as a 3D-printed electrode material.

3D-printed sensor decorated with nanomaterials by CO2 laser ablation and electrochemical treatment for non-enzymatic tyrosine detection

The combination of CO₂ laser ablation and electrochemical surface treatments is demonstrated to improve the electrochemical performance of carbon black/polylactic acid (CB/PLA) 3D-printed electrodes through the growth of flower-like Na₂O nanostructures on their surface. Scanning electron microscopy images revealed that the combination of treatments ablated the electrode's polymeric layer, exposing a porous surface where Na₂O flower-like nanostructures were formed. The electrochemical performance of the fabricated electrodes was measured by the reversibility of the ferri/ferrocyanide redox couple presenting a significantly improved performance compared with electrodes treated by only one of the steps. Electrodes treated by the combined method also showed a better electrochemical response for tyrosine oxidation. These electrodes were used as a non-enzymatic tyrosine sensor for quantification in human urine samples. Two fortified urine samples were analyzed, and the recovery values were 106 and 109%. The LOD and LOQ for tyrosine determination were 0.25 and 0.83 μmol L^-1, respectively, demonstrating that the proposed devices are suitable sensors for analyses of biological samples, even at low analyte concentrations.

3D Printed Platform for Impedimetric Sensing of Liquids and Microfluidic Channels

Fused deposition modeling 3D printing (FDM-3DP) employing electrically conductive filaments has recently been recognized as an exceptionally attractive tool for the manufacture of sensing devices. However, capabilities of 3DP electrodes to measure electric properties of materials have not yet been explored. To bridge this gap, we employ bimaterial FDM-3DP combining electrically conductive and insulating filaments to build an integrated platform for sensing conductivity and permittivity of liquids by impedance measurements. The functionality of the device is demonstrated by measuring conductivity of aqueous potassium chloride solution and bottled water samples and permittivity of water, ethanol, and their mixtures. We further implement an original idea of applying impedance measurements to investigate dimensions of 3DP channels as base structures of microfluidic devices, complemented by their optical microscopic analysis. We demonstrate that FDM-3DP allows the manufacture of microchannels of width down to 80 μm.

Exploring the coating of 3D-printed insulating substrates with conductive composites: a simple, cheap and versatile strategy to prepare customized high-performance electrochemical sensors

The development of 3D-printed electrochemical sensors by fused deposition modeling (FDM) has been increasing exponentially in the last five years. In this context, commercial conductive filaments composed of a blend of carbon particles (e.g., graphene or carbon black (CB)) and insulating thermoplastic polymers (e.g., polylactic acid (PLA) or acrylonitrile butadiene styrene (ABS)) have been widely used for electrode fabrication. However, such materials may be expensive and the electrodes when used "as-printed" exhibit poor electrochemical performance as a function of the low content of conductive particles in the composition (∼10 to 20 wt%), which requires one or more post-treatment steps (e.g. polishing, chemical, electrochemical, and photochemical) to reach good electrochemical performance. In this technical note a less used approach to produce "ready-to-use" electrochemical platforms based on 3D printing is explored, which consists of the coating of 3D-printed insulating substrates with homemade conductive composites. To demonstrate the potentiality of this alternative protocol, 3D-printed ABS insulating substrates at two geometries were coated in a highly loaded graphite (55 wt%) homemade composite (G-ABS) and evaluated for the detection of the ferri/ferrocyanide redox probe and model analytes in stationary and hydrodynamic 3D-printed systems (nitrite in micro-flow injection analysis/μFIA and paracetamol in batch injection analysis/BIA, respectively). The analytical parameters acquired with the coated electrodes were comparable to those obtained using conventional electrodes (glassy carbon, boron-doped diamond and carbon screen-printed) and 3D-printed sensors fabricated with commercial filaments. Moreover, the inclusion of carbon black in the fluid conductive composite was demonstrated as a perspective to obtain modified coated 3D-printed surfaces easily for the first time. This alternative "do it yourself" strategy is promising for the large-scale production of very cheap (US$ 0.08) and high-performance electrodes based on FDM 3D printing. Moreover, this approach dispenses the acquisition of commercial conductive filaments and the laborious development of homemade filaments.

Electrically Conductive Fused Deposition Modeling Filaments: Current Status and Medical Applications

Fused Deposition Modeling (FDM) is one of the most popular three dimensional (3D) printing techniques especially among researchers. Recently, FDM has been widely developed and improved in many areas. One of these improvements is the introduction of electrically conductive filaments. In general, conductive filaments are usually made of conductive polymer composites. These composites consist of a thermoplastic material blended with carbon-based materials. The quantity of commercially available conductive filaments has grown significantly in recent years. This paper presents a sample of currently available conductive filaments (eight filaments were chosen). These samples were compared by measuring resistance value and highlighting resulted defects of each sample. Additionally, this paper searched and reviewed articles that used conductive FDM filaments in medical applications. These articles were collected and summarized in terms of name of filaments were used, the specific function of the printed conductive object, and name of the printer used to print the conductive object. In conclusion, the main purpose of this project is to facilitate the work of future medical researchers who would like to use commercially available conductive FDM filaments.

Additively manufactured electrodes for the electrochemical detection of hydroxychloroquine

Although studies have demonstrated the inactivity of hydroxychloroquine (HCQ) towards SARS-CoV-2, this compound was one of the most prescribed by medical organizations for the treatment of hospitalized patients during the coronavirus pandemic. As a result of it, HCQ has been considered as a potential emerging contaminant in aquatic environments. In this context, we propose a complete electrochemical device comprising cell and working electrode fabricated by the additive manufacture (3D-printing) technology for HCQ monitoring. For this, a 3D-printed working electrode made of a conductive PLA containing carbon black assembled in a 3D-printed cell was associated with square wave voltammetry (SWV) for the fast and sensitive determination of HCQ. After a simple surface activation procedure, the proposed 3D-printed sensor showed a linear response towards HCQ detection (0.4-7.5 μmol L^-1) with a limit of detection of 0.04 μmol L^-1 and precision of 2.4% (n = 10). The applicability of this device was shown to the analysis of pharmaceutical and water samples. Recovery values between 99 and 112% were achieved for tap water samples and, in addition, the obtained concentration values for pharmaceutical tablets agreed with the values obtained by spectrophotometry (UV region) at a 95% confidence level. The proposed device combined with portable instrumentation is promising for on-site HCQ detection.

Multi-electrode platform for selective electrochemical sensing: 3D-printed insulating plastic is turned into a five-electrodes chip

We report a method to turn a 3D-printed plastic piece into a five-electrodes chip for multiple analytes detection. A chip containing Pd, Ni, and Ru working electrodes is used to sense hydroquinone, acetaminophen, salicylic acid, and hydroxychloroquine at once. The analysis is sequentially achieved simply by changing the proper electrode connection, without changing mobile parts, neither adding reactants, nor electrolytes. This strategy is an alternative for low-cost selective electrochemical detection.

3D-printed electrochemical platform with multi-purpose carbon black sensing electrodes

The 3D printing is described of a complete and portable system comprising a batch injection analysis (BIA) cell and an electrochemical platform with eight sensing electrodes. Both BIA and electrochemical cells were printed within 3.4 h using a multimaterial printer equipped with insulating, flexible, and conductive filaments at cost of ca. ~ U$ 1.2 per unit, and their integration was based on a threadable assembling without commercial component requirements. Printed electrodes were exposed to electrochemical/Fenton pre-treatments to improve the sensitivity. Scanning electron microscopy and electrochemical impedance spectroscopy measurements upon printed materials revealed high-fidelity 3D features (90 to 98%) and fast heterogeneous rate constants ((1.5 ± 0.1) × 10⁻³ cm s⁻¹). Operational parameters of BIA cell were optimized using a redox probe composed of [Fe(CN)₆]^4−/3− under stirring and the best analytical performance was achieved using a dispensing rate of 9.0 µL s⁻¹ and an injection volume of 2.0 µL. The proof of concept of the printed device for bioanalytical applications was evaluated using adrenaline (ADR) as target analyte and its redox activities were carefully evaluated through different voltammetric techniques upon multiple 3D-printed electrodes. The coupling of BIA system with amperometric detection ensured fast responses with well-defined peak width related to the oxidation of ADR applying a potential of 0.4 V vs Ag. The fully 3D-printed system provided suitable analytical performance in terms of repeatability and reproducibility (RSD ≤ 6%), linear concentration range (5 to 40 µmol L⁻¹; R² = 0.99), limit of detection (0.61 µmol L⁻¹), and high analytical frequency (494 ± 13 h⁻¹). Lastly, artificial urine samples were spiked with ADR solutions at three different concentration levels and the obtained recovery values ranged from 87 to 118%, thus demonstrating potentiality for biological fluid analysis. Based on the analytical performance, the complete device fully printed through additive manufacturing technology emerges as powerful, inexpensive, and portable tool for electroanalytical applications involving biologically relevant compounds.

Innovation in potentiometry: 3D-printed polylactic acid-based ion-selective bulk electrode membranes

Although ion-selective membrane-based potentiometric sensors have already proved their analytical performance in several fields of life, their applicability is still limited in practice. Biodegradable, ionic additive-free, polylactic acid-based bulk electrode membrane matrix containing various environmentally friendly polyethylene glycol derivatives as plasticizer was developed for the first time to replace the conventional PVC-based ones. Moreover, the first introduction of 3D printing in potentiometric chemosensing was also reported. It was demonstrated that a thoroughly optimized and generalizable procedure for filament extrusion combined with 3D printing technology provides a unique tool for series production of the redesigned ion-selective bulk electrochemical membranes. Finally, the potentiometric detection of Hg2+ in water was carried out as a proof-of-concept study on sensing. Results showed an unexpected improvement in electrochemical characteristics of the novel membranes compared to their conventional analogues. The present work expanded the practical applicability of conventional potentiometric cation-selective electrode membranes enabling their green, decentralized, and automated state-of-the-art manufacturing using a novel matrix composition.

Graphical abstract

Electrochemical (Bio)Sensors Enabled by Fused Deposition Modeling-Based 3D Printing: A Guide to Selecting Designs, Printing Parameters, and Post-Treatment Protocols

The 3D printing (or additive manufacturing, AM) technology is capable to provide a quick and easy production of objects with freedom of design, reducing waste generation. Among the AM techniques, fused deposition modeling (FDM) has been highlighted due to its affordability, scalability, and possibility of processing an extensive range of materials (thermoplastics, composites, biobased materials, etc.). The possibility of obtaining electrochemical cells, arrays, pieces, and more recently, electrodes, exactly according to the demand, in varied shapes and sizes, and employing the desired materials has made from 3D printing technology an indispensable tool in electroanalysis. In this regard, the obtention of an FDM 3D printer has great advantages for electroanalytical laboratories, and its use is relatively simple. Some care has to be taken to aid the user to take advantage of the great potential of this technology, avoiding problems such as solution leakages, very common in 3D printed cells, providing well-sealed objects, with high quality. In this sense, herein, we present a complete protocol regarding the use of FDM 3D printers for the fabrication of complete electrochemical systems, including (bio)sensors, and how to improve the quality of the obtained systems. A guide from the initial printing stages, regarding the design and structure obtention, to the final application, including the improvement of obtained 3D printed electrodes for different purposes, is provided here. Thus, this protocol can provide great perspectives and alternatives for 3D printing in electroanalysis and aid the user to understand and solve several problems with the use of this technology in this field.

Influence of filament aging and conductive additive in 3D printed sensors

3D printing technology combined with electrochemical techniques have allowed the development of versatile and low-cost devices. However, some aspects need to be considered for the good quality and useful life of the sensors. In this work, we have demonstrated herein that the filament aging, the conductive material, and the activation processes (post-treatments) can influence the surface characteristics and the electrochemical performance of the 3D printed sensors. Commercial filaments and 3D printed sensors were morphologically, thermally, and electrochemically analyzed. The activated graphene-based (Black Magic®) sensor showed the best electrochemical response, compared to the carbon black-filament (Proto-Pasta®). In addition, we have proven that filament aging harms the performance of the sensors since the electrodes produced with three years old filament had a considerably lower intra-days reproducibility. Finally, the activated graphene-based sensor has shown the best performance for the electrochemical detection of bisphenol A, demonstrating the importance of evaluating and control the characteristics and quality of filaments to improve the mechanical, conductive, and electrochemical performance of 3D printed sensors.

Electrochemical determination of several biofuel antioxidants in biodiesel and biokerosene using polylactic acid loaded with carbon black within 3D-printed devices

Low oxidation stability is the main drawback of biodiesels and biokerosenes that is overcome by using antioxidants, which can be combined due to synergistic effects. This paper demonstrates that 3D-printed electrochemical devices can be applied to biofuel electroanalysis, including the monitoring of oxidation stability by quantifying the antioxidant content in biofuels. Fabrication requires 3D-printed acrylic templates at which a polylactic acid (PLA) filament with conducting carbon-black filling sensors is extruded by a 3D pen. The antioxidants butyl hydroxyanisole (BHA) and tert-butylhydroquinone (TBHQ) are the most employed additives in biodiesel production, and thus, their electrochemical behavior was investigated; 2,6-ditertbutylphenol (2,6-DTBP) was included in this investigation because it is commonly added to biokerosenes. The electrochemical surface treatment of the 3D-printed electrodes improved the current responses of all antioxidants; however, the electrochemical oxidation of TBHQ was clearly more affected by an electrocatalytic action shifting its oxidation towards less positive potentials (~200 mV), which resulted in a better separation of TBHQ and BHA oxidation peaks (+0.4 and +0.6 V vs Ag|AgCl, respectively). The oxidation of 2,6-DTBP occurred at more positive potentials (+1.2 V vs Ag|AgCl). The simultaneous determination of TBHQ and BHA by differential-pulse voltammetry resulted in linear responses in the range 0.5 and 175 μmol L^-1 with limits of detection and quantification of 0.15 μmol L^-1 and 0.5 μmol L^-1, respectively. The presence of Fe³⁺, Cu²⁺, Pb²⁺, Mn²⁺, Cd²⁺, and Zn²⁺, even in high concentrations, did not interfere in the determination of TBHQ and BHA. The determination of 2,6-DTBP in biokerosene was achieved by cyclic voltammetry. All relative standard deviations (RSD) were lower than 6.0 %, indicating adequate precision of the methods. Spiked biofuel samples were analyzed (after dilution in electrolyte) and recovery values between 85 and 120% were obtained, which indicates absence of sample matrix effects.

Non-invasive electrochemistry-driven metals tracing in human biofluids

Wearable analytical devices represent the future for fast, de-centralized, and human-centered health monitoring. Electrochemistry-based platforms have been highlighted as the role model for future developments amid diverse strategies and transduction technologies. Among the various relevant analytes to be real-time and non-invasively monitored in bodily fluids, we review the latest wearable achievements towards determining essential and toxic metals. On-skin measurements represent an excellent possibility for humankind: real-time monitoring, digital/fast communication with specialists, quick interventions, removing barriers in developing countries. In this review, we discuss the achievements over the last 5 years in non-invasive electrochemical platforms, providing a comprehensive table for quick visualizing the diverse sensing/technological advances. In the final section, challenges and future perspectives about wearables are deeply discussed.

Additively manufactured carbon/black-integrated polylactic acid 3Dprintedsensor for simultaneous quantification of uric acid and zinc in sweat

For the first time the development of an electrochemical method for simultaneous quantification of Zn²⁺ and uric acid (UA) in sweat is described using an electrochemically treated 3D-printed working electrode. Sweat analysis can provide important information about metabolites that are valuable indicators of biological processes. Improved performance of the 3D-printed electrode was achieved after electrochemical treatment of its surface in an alkaline medium. This treatment promotes the PLA removal (insulating layer) and exposes carbon black (CB) conductive sites. The pH and the square-wave anodic stripping voltammetry technique were carefully adjusted to optimize the method. The peaks for Zn²⁺ and UA were well-defined at around - 1.1 V and + 0.45 V (vs. CB/PLA pseudo-reference), respectively, using the treated surface under optimized conditions. The calibration curve showed a linear range of 1 to 70 µg L^-1 and 1 to 70 µmol L^-1 for Zn²⁺ and UA, respectively. Relative standard deviation values were estimated as 4.8% (n = 10, 30 µg L^-1) and 6.1% (n = 10, 30 µmol L^-1) for Zn²⁺ and UA, respectively. The detection limits for Zn²⁺ and UA were 0.10 µg L^-1 and 0.28 µmol L^-1, respectively. Both species were determined simultaneously in real sweat samples, and the achieved recovery percentages were between 95 and 106% for Zn²⁺ and 82 and 108% for UA.

3D Printed Electrochemical Sensors

Three-dimensional (3D) printing has recently emerged as a novel approach in the development of electrochemical sensors. This approach to fabrication has provided a tremendous opportunity to make complex geometries of electrodes at high precision. The most widely used approach for fabrication is fused deposition modeling; however, other approaches facilitate making smaller geometries or expanding the range of materials that can be printed. The generation of complete analytical devices, such as electrochemical flow cells, provides an example of the array of analytical tools that can be developed. This review highlights the fabrication, design, preparation, and applications of 3D printed electrochemical sensors. Such developments have begun to highlight the vast potential that 3D printed electrochemical sensors can have compared to other strategies in sensor development.

Development of highly sensitive electrochemical sensor using new graphite/acrylonitrile butadiene styrene conductive composite and 3D printing-based alternative fabrication protocol

Here, a novel electrically conductive thermoplastic material composed of graphite/acrylonitrile butadiene styrene (G/ABS) is reported for the first time. This material was explored on the production of 3D printing-based electrochemical sensors with enhanced sensitivity using a novel fabrication approach. The developed G/ABS electrodes showed lower charge transfer resistance (157 vs. 3279 Ω), higher electroactive area (0.61 vs. 0.19 cm²) and peak currents ca. 69% higher when compared with electrodes fabricated using carbon black/polylactic acid (CB/PLA) commercial filament, which has been widely explored in recent literature. Moreover, the G/ABS sensor provided satisfactory repeatability, reproducibility and stability (relative standard deviations (RSDs) were 1.14%, 6.81% and 10.62%, respectively). This improved performance can be attributed to the fabrication protocol developed here, which allows the incorporation of greater amounts of conductive material in the polymeric matrix. The G/ABS electrode also required a simpler and quicker protocol for activation when compared to CB/PLA. As proof of concept, the G/ABS sensor was employed for electroanalytical quantification of paracetamol (PAR) in pharmaceutical products. The linear concentration range was observed from 0.20 to 30 μmol L^-1 and the limit of detection achieved was 54 nmol L^-1, much lower than several recent studies dealing with the same analyte. The sensitivity of the G/ABS electrode regarding PAR was also far better when compared to CB/PLA sensor (0.50 μA/μmol L^-1 vs. 0.12 μA/μmol L^-1). Analyses in commercial pill samples showed good accuracy (recoveries ca. 108%) and precision (RSDs < 5%), suggesting great potential for use of this novel conductive thermoplastic in electroanalytical applications based on 3D printing.

Multi sensor compatible 3D-printed electrochemical cell for voltammetric drug screening

3D printing is a hot topic in electroanalytical chemistry, allowing the construction of custom cells and sensors at affordable prices. In this work, we describe a novel small and practical 3D-printed electrochemical cell. The cell's body, manufactured in ABS on a 3D printer, is composed by three parts easily screwed: solution vessel, stick and cover with two embedded 3D-pen-printed carbon black-polylactic acid (CB-PLA) electrodes (counter and pseudo-reference). The cell is compatible with any planar working electrode, in which boron-doped diamond, graphite sheet (GS) and 3D-printed CB-PLA were shown as examples. A new alternative protocol to quickly produce 3D-printed sensors using a 3D pen and other low-cost apparatus is also proposed. The voltammetric performance of each evaluated sensor was carried out in the presence of redox probe ferricyanide and paracetamol as model analyte, and the surfaces were characterized by electrochemical impedance spectroscopy and scanning electrochemical microscopy. To present an analytical application of the 3D-printed cell, low-cost flexible sensors (GS and CB-PLA) were used as integrated platforms for sampling and detection of solid drugs. As a proof-of-concept, traces of drugs with a historic of counterfeit or adulteration (sildenafil citrate, tadalafil, losartan and 17α-ethinylestradiol) were abrasively sampled over the sensor and assembled on 3D-printed cell to perform a fast voltammetric scan in the presence of only 500 μL of electrolyte. This protocol is attractive for pharmaceutical and forensic sciences as a simple preliminary screening method which could identify the presence or absence of the suspicious drug as well as impurities or adulterants. The 3D-printed cell was also used for the determination of 17α-ethinylestradiol in a contraceptive pill to demonstrate a quantitative analysis. The cell is quickly printed (90 min), cheap (US$ 0.30) and requires low electrolyte volumes (0.5-3.0 mL), being suitable to be used in several other electroanalyses, especially for on-site applications.

Recent progress of conductive 3D-printed electrodes based upon polymers/carbon nanomaterials using a fused deposition modelling (FDM) method as emerging electrochemical sensing devices

3D-printing or additive manufacturing is presently an emerging technology in the fourth industrial revolution that promises to reshape traditional manufacturing processes. The electrochemistry field can undoubtedly take advantage of this technology to fabricate electrodes to create a new generation of electrode sensor devices that could replace conventionally manufactured electrodes; glassy carbon, screen-printed carbon and carbon composite electrodes. In the electrochemistry research area, studies to date show that there is a demand for electrically 3D printable conductive polymer/carbon nanomaterial filaments where these materials can be printed out through an extrusion process based upon the fused deposition modelling (FDM) method. FDM could be used to manufacture novel electrochemical 3D printed electrode sensing devices for electrochemical sensor and biosensor applications. This is due to the FDM method being the most affordable 3D printing technique since conductive and non-conductive thermoplastic filaments are commercially available. Therefore, in this minireview, we focus on only the most outstanding studies that have been published since 2018. We believe this to be a highly-valuable research area to the scientific community, both in academia and industry, to enable novel ideas, materials, designs and methods relating to electroanalytical sensing devices to be generated. This approach has the potential to create a new generation of electrochemical sensing devices based upon additive manufacturing. This minireview also provides insight into how the research community could improve the electrochemical performance of 3D-printed electrodes to significantly increase the sensitivity of the 3D-printed electrodes as electrode sensing devices.

3D-printing for forensic chemistry: voltammetric determination of cocaine on additively manufactured graphene-polylactic acid electrodes

Cocaine is probably one of the most trafficked illicit drugs in the world. For this reason, police forces require fast, selective, and sensitive methods for cocaine detection at crime scenes. Taking benefit of additive manufacturing, we demonstrate that 3D-printed graphene-polylactic acid (G-PLA) electrodes using the affordable fused deposition modelling technique can identify and quantify cocaine in seized drugs. The detection of cocaine based on its electrochemical oxidation on such electrodes was dramatically improved after an electrochemical surface treatment that generates reduced graphene oxide (anodic followed by a cathodic treatment). Square-wave voltammetric determination of cocaine was achieved in the concentration range between 20 and 100 μmol L-1, with a detection limit of 6 μmol L-1, and free from the interference of paracetamol, caffeine, phenacetin, lidocaine, benzocaine and levamisole, which are common adulterants found in seized drugs. The analytical characteristics obtained using 3D-printed G-PLA electrodes were comparable with those of previously reported electrochemical sensors, but presented the inherent advantages of the 3D-printing technology that enables low-cost, reproducible, and large-scale production of such electrodes in remote areas combined with the use of an environmentally-friendly biopolymer.