Epoxy and amide crosslinked polarity enhanced polysaccharides binder for silicon anode in lithium-ion batteries

Achievements, challenges, and perspectives in the design of polymer binders for advanced lithium-ion batteries

Energy storage devices with high power and energy density are in demand owing to the rapidly growing population, and lithium-ion batteries (LIBs) are promising rechargeable energy storage devices. However, there are many issues associated with the development of electrode materials with a high theoretical capacity, which need to be addressed before their commercialization. Extensive research has focused on the modification and structural design of electrode materials, which are usually expensive and sophisticated. Besides, polymer binders are pivotal components for maintaining the structural integrity and stability of electrodes in LIBs. Polyvinylidene difluoride (PVDF) is a commercial binder with superior electrochemical stability, but its poor adhesion, insufficient mechanical properties, and low electronic and ionic conductivity hinder its wide application as a high-capacity electrode material. In this review, we highlight the recent progress in developing different polymeric materials (based on natural polymers and synthetic non-conductive and electronically conductive polymers) as binders for the anodes and cathodes in LIBs. The influence of the mechanical, adhesion, and self-healing properties as well as electronic and ionic conductivity of polymers on the capacity, capacity retention, rate performance and cycling life of batteries is discussed. Firstly, we analyze the failure mechanisms of binders based on the operation principle of lithium-ion batteries, introducing two models of "interface failure" and "degradation failure". More importantly, we propose several binder parameters applicable to most lithium-ion batteries and systematically consider and summarize the relationships between the chemical structure and properties of the binder at the molecular level. Subsequently, we select silicon and sulfur active electrode materials as examples to discuss the design principles of the binder from a molecular structure point of view. Finally, we present our perspectives on the development directions of binders for next-generation high-energy-density lithium-ion batteries. We hope that this review will guide researchers in the further design of novel efficient binders for lithium-ion batteries at the molecular level, especially for high energy density electrode materials.

Regulating Grafting Density to Realize High-Areal-Capacity Silicon Submicroparticle Anodes Under Ultralow Binder Content

Grafted biopolymer binders are demonstrated to improve the processability and cycling stability of the silicon (Si) nanoparticle anodes. However, there is little systematical exploration regarding the relationship between grafting density and performance of grafted binder for Si anodes, especially when Si particles exceed the critical breaking size. Herein, a series of guar gum grafted polyacrylamide (GP) binders with different grafting densities are designed and prepared to determine the optimal grafting density for maximizing the electrochemical performance of Si submicroparticle (SiSMP) anodes. Among various GP binders, GP5 with recommended grafting density demonstrates the strongest adhesion strength, best mechanical properties, and highest intrinsic ionic conductivity. These characteristics enable the SiSMP electrodes to sustain the electrode integrity and accelerate lithium-ion transport kinetics during cycling, resulting in high capacity and stable cyclability. The superior role of GP5 binder in enabling robust structure and stable interface of SiSMP electrodes is revealed through the PeakForce atomic force microscopy and in situ differential electrochemical mass spectrometry. Furthermore, the stable cyclabilities of high-loading SiSMP@GP5 electrode with ultralow GP5 content (1 wt%) at high areal capacity as well as the good cyclability of Ah-level LiNi0.8Co0.1Mn0.1O2/SiSMP@GP5 pouch cell strongly confirms the practical viability of the GP5 binder.

Highly Stable Silicon Anode Enabled by a Water-Soluble Tannic Acid Functionalized Dual-Network Binder

Silicon (Si), a high-capacity electrode material, is crucial for achieving high-energy-density lithium-ion batteries. However, Si suffers from poor cycling stability due to its significant volume changes during operation. In this work, a tannic acid functionalized aqueous dual-network binder with an intramolecular tannic acid functionalized network has been synthesized, which is composed of covalent-cross-linked polyamide and ionic-cross-linked alginate (Alg(Ni)-PAM-TA), and employed as an advanced binder for stabilizing Si anodes. The resultant Alg(Ni)-PAM-TA binder, incorporating diverse functional groups including amide, carboxylic acid, and dynamic hydrogen bonds, can easily interact with both Si nanoparticles and the Cu foil, thereby facilitating the formation of a highly resilient network characterized by exceptional adhesion strength. Moreover, molecular dynamics (MD) simulations indicate that the Alg(Ni)-PAM-TA network shows an increased intramolecular hydrogen bond number with increasing concentration of TA and a decreased intramolecular hydrogen bond between PAM and Alg as a result of the aggregation behavior of tannic acids themselves. Consequently, the binder significantly enhances the Si electrode's integrity throughout repeated charge/discharge cycles. At a current density of 0.84 A g-1, the Si electrode retains a capacity of 1863.4 mAh g-1 after 200 cycles. This aqueous binder functionalized with the intramolecular network via the incorporation of TA molecules holds great promise for the development of high-energy-density lithium-ion batteries.

Novel Flurbiprofen Derivatives as Antioxidant and Anti-Inflammatory Agents: Synthesis, In Silico, and In Vitro Biological Evaluation

In this study, we present the synthesis of five novel compounds by combining flurbiprofen with various substituted 2-phenethylamines. The synthesized derivatives underwent comprehensive characterization using techniques such as 1H- and 13C-NMR spectroscopy, UV-Vis spectroscopy, and high-resolution mass spectrometry (HRMS). Detailed HRMS analysis was performed for each of these newly created molecules. The biological activities of these compounds were assessed through in vitro experiments to evaluate their potential as anti-inflammatory and antioxidant agents. Furthermore, the lipophilicity of these derivatives was determined, both theoretically using the cLogP method and experimentally through partition coefficient (RM) measurements. To gain insights into their binding affinity, we conducted an in silico analysis of the compounds' interactions with human serum albumin (HSA) using molecular docking studies. Our findings reveal that all of the newly synthesized compounds exhibit significant anti-inflammatory and antioxidant activities, with results statistically comparable to the reference compounds. Molecular docking studies further explain the observed in vitro results, shedding light on the molecular mechanisms behind their biological activities. Using in silico method, toxicity was calculated, resulting in LD50 values. Depending on the administration route, the novel flurbiprofen derivatives show lower toxicity compared to the standard flurbiprofen.

Advanced inorganic lithium metasilicate binder for high-performance silicon anode

Silicon (Si) is considered a high-capacity anode material with potential for next-generation lithium-ion batteries. However, the commercial application of Si anode is seriously hindered by huge volume variation (>300%) and limited Li+ diffusion ability. Herein, lithium metasilicate (LS), a novel inorganic binder, was innovatively developed to accommodate these challenges. Favorable compatibility is observed between the LS binder and Si nanoparticles (SiNPs) due to the existence of Si element within the LS skeleton. The interaction of the LS binder and SiNPs leads to a strong adhesion effect, enhancing the cycling stability of Si anode. The Si electrode with the LS binder presented an average discharge capacity of 2123 mAh/g at 0.84 A/g after 100 cycles. Furthermore, the presence of the Li+ transport channel within the LS binder enhances Li+ diffusion ability within Si anode. As a result, the average discharge capacity reaches 663 mAh/g at 8.4 A/g. This work thus explored new inorganic binder design approaches for Si anode, contributing to the advancement of high-performance Si anode.

High-ICE and High-Capacity Retention Silicon-Based Anode for Lithium-Ion Battery

Silicon-based anodes are promising to replace graphite-based anodes for high-capacity lithium-ion batteries (LIB). However, the charge–discharge cycling suffers from internal stresses created by large volume changes of silicon, which form silicon-lithium compounds, and excessive consumption of lithium by irreversible formation of lithium-containing compounds. Consumption of lithium by the initial conditioning of the anode, as indicated by low initial coulombic efficiency (ICE), and subsequently continuous formation of solid-electrolyte-phase (SEI) on the freshly exposed silicon surface, are among the main issues. A high-performance, silicon-based, high-capacity anode exhibiting 88.8% ICE and the retention of 2 mAh/cm² areal capacity after 200 discharge–charge cycles at the rate of 1 A/g is reported. The anode is made on a copper foil using a mixture of 70%:10%:20% by weight ratio of silicon flakes of 100 × 800 × 800 nm in size, Super P conductivity enhancement additive, and an equal-weight mixture of CMC and SBR binders. Pyrolysis of fabricated anodes at 700 °C in argon environment for 1 h was applied to convert the binders into a porous graphitic carbon structure that encapsulates individual silicon flakes. The porous anode has a mechanically strong and electrically conductive graphitic carbon structure formed by the pyrolyzed binders, which protect individual silicon flakes from excessive reactions with the electrolyte and help keep small pieces of broken silicon flakes together within the carbon structure. The selection and amount of conductivity enhancement additives are shown to be critical to the achievement of both high-ICE and high-capacity retention after long cycling. The Super P conductivity enhancement additive exhibits a smaller effective surface area where SEI forms compared to KB, and thus leads to the best combination of both high-ICE and high-capacity retention. A silicon-based anode exhibiting high capacity, high ICE, and a long cycling life has been achieved by the facile and promising one-step fabrication process.

Epoxy Cross-Linking Enhanced the Toughness of Polysaccharides as a Silicon Anode Binder for Lithium-Ion Batteries

The large volume expansion of a silicon anode induces serious mechanical failure and limits its applications. Owing to the intrinsic weak van der Waals force and poor toughness, it is unable to solve this issue with the current commercial poly(vinylidene difluoride) (PVDF) binder. The development of a binder with strong binding strength with silicon (Si) is urgent. Herein, a hydroxyl-rich three-dimensional (3D) network binder is synthesized by chemical cross-linking reactions between epichlorohydrin (ECH) and sodium hyaluronate (SH), which exhibits dramatically enhanced toughness and cohesive properties. The Si anode with the novel SH-ECH as the binder delivers excellent electrochemical performance, especially cycling stability. The discharge capacity could maintain 800.4 mAh g^-1 after 1000 cycles at a current of 0.2 C with the average capacity decay rate per cycle of 0.015%. Our results pave a new way for the tailoring of the chemical structures of natural polymers to realize lithium-ion batteries (LIBs) with superior electrochemical performance.