Influence of some physicochemical parameters on the passive sampling of copper (II) from aqueous medium using a polymer inclusion membrane device

Appraisal on the role of passive sampling for more integrative frameworks on the environmental risk assessment of contaminants

Over time multiple lines of research have been integrated as important components of evidence for assessing the ecological quality status of water bodies within the framework of Environmental Risk Assessment (ERA) approaches. One of the most used integrative approaches is the triad which combines, based on the weight-of-evidence, three lines of research, the chemical (to identify what is causing the effect), the ecological (to identify the effects at the ecosystem level) and the ecotoxicological (to ascertain the causes of ecological damage), with the agreement between the different lines of risk evidence increasing the confidence in the management decisions. Although the triad approach has proven greatly strategic in ERA processes, new assessment (and monitoring) integrative and effective tools are most welcome. In this regard, the present study is an appraisal on the boost that passive sampling, by allowing to increase information reliability, can give within each of the triad lines of evidence, for more integrative ERA frameworks. In parallel to this appraisal, examples of works that used passive samplers within the triad are presented providing support for the use of these devices in a complementary form to generate holistic information for ERA and ease the process of decision-making.

Sensing Cd(II) Using a Disposable Optical Sensor Based on a Schiff Base Immobilisation on a Polymer-Inclusion Membrane. Applications in Water and Art Paint Samples

A disposable colour-changeable optical sensor based on an interesting polymer inclusion-membrane (PIM) was designed to determine Cd(II) ions in aqueous medium. The Schiff base 2-acetylpyridine benzoylhydrazone (2-APBH) immobilised on the polymer membrane was used as a sensing molecule. The amounts of the PIM components were optimised by a 3² fractional factorial design with two central points and two blocks. The best optical sensor composition consisted of 2.5 g of poly(vinylchloride) (PVC) as a base polymer, 3 mL of tributyl phosphate (TBP) as a plasticiser, and 0.02 g of 2-APBH as a reagent. The sensor showed a good linear response in the range from 0.02 mg L⁻¹ (limit of detection) to 1 mg L⁻¹ of Cd(II) under the following experimental conditions: pH 9.5 (adjusted using ammonium chloride buffer solution at 0.337 mol L⁻¹), 60 min of exposure time plus 2 min of sonication (pulses at 2 s intervals), and 10 min of short-term stability. The relative standard deviation of the method was determined to be 4.04% for 0.4 mg L⁻¹ of Cd(II). The optical sensor was successfully applied to the determination of Cd(II) in natural-water and art-paint samples.

Technical design and optimisation of polymer inclusion membranes (PIMs) for sample pre-treatment and passive sampling - A review

This review reports on the increasing interest in technical designs, calibration, and application of PIM-based devices in sample pre-treatment and passive sampling in environmental water monitoring from 2010 to 2021. With regards to passive sampling, devices are calibrated in a laboratory setup using either a dip-in or flow-through approach before environmental application. In sample preparation, the device set-ups can be offline, online or in a continuous flow separation device connected to a flow injection analysis system. The PIMs have also demonstrated potential in both these offline and online separations; however, there is still a draw-back of low diffusion coefficients obtained in these PIM set-ups. Electro-driven membrane (EME) extraction has demonstrated better performance as well as improved analyte flux. Critical in electro-driven membrane extraction is applying correct voltage that may not compromise the PIM performance due to leaching of components to the aqueous solutions. Further, besides different PIM configurations and designs being developed, PIM based extractions are central to PIM components (base polymer, carrier and plasticizer). As such, recent studies have also focused on improving PIM stability by investigating use of various PIM components, incorporating nano additives into the PIM composition, and investigating novel green PIM synthetic routes. All these aspects are covered in this review. Further, some recent studies that have demonstrated the ability to eliminate effects of flow patterns and membrane biofouling in PIM based applications are also included.