Simultaneous removal of rhodamine B and Cr(VI) from water using cellulose carbon nanofiber incorporated with bismuth oxybromide: The effect of cellulose pyrolysis temperature on photocatalytic performance

Zinc Oxide-Loaded Cellulose-Based Carbon Gas Sensor for Selective Detection of Ammonia

Cellulose-based carbon (CBC) is widely known for its porous structure and high specific surface area and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, a ZnO/CBC heterojunction was formed by means of simple co-precipitation and high-temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia that the previous pure ZnO ammonia sensor cannot at room temperature. It has a great gas sensing response, stability, and selectivity to an ammonia concentration of 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

Synergetic effect of photocatalytic oxidation plus catalytic oxidation on the performance of coconut shell fiber biochar decorated α-MnO2 under visible light towards BPA degradation

Photocatalytic technology is regarded as a promising approach for fast degradation of refractory organic pollutant in water. However, the performance of the photocatalyst can be restricted by the variation of water matrix conditions. Herein, coconut shell fiber was pyrolyzed to biochar (CSB800) and incorporated with α-MnO2 to degrade bisphenol A (BPA) in water under visible light irradiation. The prepared α-MnO2/CSB800 composites demonstrated high efficacy in degrading BPA. Specifically, 0.01 mM of BPA could be completely degraded by 0.1 g/L of MnO2/CSB800 within 45 min. It was found that the incident light could effectively trigger the separation of electron and hole in α-MnO2. The electron and hole were afterwards converted to hydroxyl radical (●OH), superoxide radical (●O2-) and non-radical singlet oxygen (1O2), which subsequently initiated the photocatalytic degradation of BPA. Additionally, α-MnO2/CSB800 could simultaneously participate the oxidative degradation pathway of BPA with its high oxidation-reduction potential. The introduction of CSB800 led to higher BPA degradation efficiency since CSB800 could accelerate the charge carrier transferring rate during BPA degradation process via either pathway. The co-existence of both photocatalytic and oxidative degradation synergy enables α-MnO2/CSB800/visible light system with high catalytic performance stability towards various water matrices. This study proposes an effective strategy to prepare easy-available photocatalysts with high and stable performance towards for addressing organic pollution issues in water.

Wood induced preparation of Fe3C decorated biochar for peroxymonosulfate activation towards bisphenol a degradation with low ion leaching

Heterogeneous iron/persulfate system suffers from the problems of high ion leaching, severe catalyst surface corrosion and low performance stability. Herein, a series of iron compound incorporated N doped biochar composite catalysts were prepared from pyrolyzing wood powder and ferric ferrocyanide mixture, which were used for bisphenol A (BPA) degradation in water through peroxymonosulfate (PMS) activation. It was found that the reducing gases released from wood powder at different pyrolysis temperature significantly affected the crystalline phase of the iron compound in the catalyst, in which pure phase iron carbide (Fe₃C) decorated N doped biochar was obtained at pyrolysis temperature of 600 °C or higher. Wood powder was introduced as both Fe₃C formation inductive agent and biochar precursor. Fe₃C/biochar exhibited optimal BPA degradation performance, in which 0.5 g/L of catalyst could completely degrade 0.05 mM BPA within 30 min. Radical, high valent iron-oxo, and non-radical species were all generated in the reaction system by both Fe₃C and N doped biochar, respectively. Moreover, the multi-valence nature of Fe in Fe₃C enabled the reaction system with remarkably reduced Fe ion leaching and negligible iron sludge production since Fe₃C could activate PMS through a heterogeneous mechanism. Having multiple active species generated for BPA degradation, the prepared catalyst also showed promising adaptability and recyclability. This study can provide a new solution for the design of iron based catalyst/PMS system for organic pollutant degradations with low ion release.

Arsenic removal and stabilization behavior of schwertmannite@BC (Sch@BC) in contaminated dual media (water/soil): Via sulfate exchange and chemical complexation

Arsenic (As) is extremely harmful to the ecological environment and human health owing to its high toxicity. The composite that biochar (BC) modified by Schwertmannite (Sch), marked as Sch@BC, were prepared to remediate As-contaminated water and soil with a high efficiency. The characterization results showed that the Sch particles were successfully loaded on the BC, providing more active sites for As(V) adsorption. Compared with the pristine BC, the adsorption capacity of Sch@BC-1 was significantly improved (50.00 mg/g), of which the adsorption capacity kept stable over a wide pH range (pH = 2-8). The adsorption process conformed to pseudo-second-order kinetics and Langmuir isotherm model, which indicated that chemical adsorption was the dominant mechanism and the adsorption rate was controlled by intraparticle diffusion. Sch@BC could adsorb As(V) through electrostatic interaction and ion exchange, forming a FeAsO₄ complex and removing As(V). The 5-week soil incubation experiment showed that 3% Sch@BC showed the optimal stabilization effect, while the proportion of stable crystalline Fe/Mn-bound fractionation (F4) increased. Moreover, the results of microbial community diversity showed that Sch@BC interacted with As-resistant dominant microorganisms such as Proteobacteria in soil, promoted their growth and reproduction, and improved the stability of As in soil. In summary, Sch@BC is an excellent agent with broad application prospects for remediating As-contaminated water and soil.

Preparation and modification of nanocellulose and its application to heavy metal adsorption: A review

Heavy metals are a notable pollutant in aquatic ecosystems that results in many deadly diseases of the human body after enrichment through the food chain. As an environmentally friendly renewable resource, nanocellulose can be competitive with other materials at removing heavy metal ions due to its large specific surface area, high mechanical strength, biocompatibility and low cost. In this review, the research status of modified nanocellulose for heavy metal adsorbents is primarily reviewed. Two primary forms of nanocellulose are cellulose nanocrystals (CNCs) and cellulose nanofibers (CNFs). The preparation process of nanocellulose was derived from natural plants, and the preparation process included noncellulosic constituent removal and extraction of nanocellulose. Focusing on heavy metal adsorption, the modification of nanocellulose was explored in depth, including direct modification methods, surface grafting modification methods based on free radical polymerization and physical activation. The adsorption principles of nanocellulose-based adsorbents when removing heavy metals are analyzed in detail. This review may further facilitate the application of the modified nanocellulose in the field of heavy metal removal.

Recent advances in cellulose supported photocatalysis for pollutant mitigation: A review

In recent times, green chemistry or "green world" is a new and effective approach for sustainable environmental remediation. Among all biomaterials, cellulose is a vital material in research and green chemistry. Cellulose is the most commonly used natural biopolymer because of its distinctive and exceptional properties such as reproducibility, cost-effectiveness, biocompatibility, biodegradability, and universality. Generally, coupling cellulose with other nanocomposite materials enhances the properties like porosity and specific surface area. The polymer is environment-friendly, bioresorbable, and sustainable which not only justifies the requirements of a good photocatalyst but boosts the adsorption ability and degradation efficiency of the nanocomposite. Hence, knowing the role of cellulose to enhance photocatalytic activity, the present review is focused on the properties of cellulose and its application in antibiotics, textile dyes, phenol and Cr(VI) reduction, and degradation. The work also highlighted the degradation mechanism of cellulose-based photocatalysts, confirming cellulose's role as a support material to act as a sink and electron mediator, suppressing the charge carrier's recombination rate and enhancing the charge migration ability. The review also covers the latest progressions, leanings, and challenges of cellulose biomaterials-based nanocomposites in the photocatalysis field.

Recent Progress on Tailoring the Biomass-Derived Cellulose Hybrid Composite Photocatalysts

Biomass-derived cellulose hybrid composite materials are promising for application in the field of photocatalysis due to their excellent properties. The excellent properties between biomass-derived cellulose and photocatalyst materials was induced by biocompatibility and high hydrophilicity of the cellulose components. Biomass-derived cellulose exhibited huge amount of electron-rich hydroxyl group which could promote superior interaction with the photocatalyst. Hence, the original sources and types of cellulose, synthesizing methods, and fabrication cellulose composites together with applications are reviewed in this paper. Different types of biomasses such as biochar, activated carbon (AC), cellulose, chitosan, and chitin were discussed. Cellulose is categorized as plant cellulose, bacterial cellulose, algae cellulose, and tunicate cellulose. The extraction and purification steps of cellulose were explained in detail. Next, the common photocatalyst nanomaterials including titanium dioxide (TiO2), zinc oxide (ZnO), graphitic carbon nitride (g-C3N4), and graphene, were introduced based on their distinct structures, advantages, and limitations in water treatment applications. The synthesizing method of TiO2-based photocatalyst includes hydrothermal synthesis, sol-gel synthesis, and chemical vapor deposition synthesis. Different synthesizing methods contribute toward different TiO2 forms in terms of structural phases and surface morphology. The fabrication and performance of cellulose composite catalysts give readers a better understanding of the incorporation of cellulose in the development of sustainable and robust photocatalysts. The modifications including metal doping, non-metal doping, and metal-organic frameworks (MOFs) showed improvements on the degradation performance of cellulose composite catalysts. The information and evidence on the fabrication techniques of biomass-derived cellulose hybrid photocatalyst and its recent application in the field of water treatment were reviewed thoroughly in this review paper.

Electrospun composite nanofibers as novel high-performance and visible-light photocatalysts for removal of environmental pollutants: A review

Environmental pollution caused by industries and human manipulations is coming a serious global challenge. On the other hand, the world is facing an energy crisis caused by population growth. Designing solar-driven photocatalysts which are inspired by the photosynthesis of plant leaves is a fantastic solution to use solar energy as green, available, and unlimited energy containing ∼50% visible light for the removal of environmental pollutants. The polymeric and non-polymeric-based electrospun composite nanofibers (NFs) are as innovative photocatalytic candidates which increase photocatalytic activity and transition from UV light to visible light and overcome the aggregation, photocorrosion, toxicity, and hard recycling and separation of the nanosized powder form of photocatalysts. The composite NFs are fabricated easily by either embedding the photocatalytic agents into the NFs during electrospinning or via their decorating on the surface of NFs post-electrospinning. Polyacrylonitrile-based, tungsten trioxide-based, zinc oxide-based, and titanium dioxide-based composite NFs were revealed as the most reported composite NFs. All the lately investigated electrospun composite NFs indicated long-term stability, high photocatalytic efficiency (∼> 80%) within a short time of light radiation (10-430 min), and high stability after several cycles of use. They were applied in various applications including degradation of dyes/antibiotics, water splitting, wastewater treatment, antibacterial usage, etc. The photogenerated species especially holes, O₂^∙-, and ^.OH were mostly responsible for the photocatalytic mechanism and pathway. The electrospun composite NFs have the potential to use in large-scale productions in condition that their thickness and recycling conditions are optimized, and their toxicity and detaching are resolved.

A review on bismuth-based materials for the removal of organic and inorganic pollutants

Modernized lifestyle and increased industrialization threaten living organisms because of the pollutants released from industries and household wastes. The presence of even small amounts of pollutants (organic pollutants (OPs) and inorganic pollutants-heavy metals (HMs)) shows significant effects. Thus wastewater treatment is urgently needed before being subjected to use. Many methods and materials have been developed and reported for the removal of pollutants from wastewater. This review focused on the removal of both OPs and HMs using bismuth-based (Bi-based) materials because of their low toxicity and excellent properties compared to other metals. Bi-based materials as a photocatalyst for photodegradation of OPs are discussed in detail with synthesis methods. Further, since few reviews are available on the Bi-based material for the removal and sensing of HMs, this topic was intentionally summarized. About 200 published articles and reviews have been reviewed here. Additionally, the key point that needs to be focused on the development of Bi-based photocatalysts for the removal of OPs and for upgrading the Bi-based materials as adsorbents for HMs are conferred in the outlook. This will help many researchers in their upcoming work.

Photocatalytic Reduction of Hexavalent Chromium Using Cu3.21Bi4.79S9/g-C3N4 Nanocomposite

The photocatalytic reduction of hexavalent chromium, Cr(VI), to the trivalent species, Cr(III), has continued to inspire the synthesis of novel photocatalysts that are capable of achieving the task of converting Cr(VI) to the less toxic and more useful species. In this study, a novel functionalized graphitic carbon nitride (Cu3.21Bi4.79S9/gC3N4) was synthesized and characterized by using X-ray diffraction (XRD), thermogravimetry analysis (TGA), energy-dispersive X-ray spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), transmission electron microscope (TEM), and scanning electron microscope (SEM). The composite was used for the photocatalytic reduction of hexavalent chromium, Cr(VI), under visible light irradiation. A 92.77% efficiency of the reduction was achieved at pH 2, using about 10 mg of the photocatalyst and 10 mg/L of the Cr(VI) solution. A pseudo-first-order kinetic study indicated 0.0076 min−1, 0.0286 min−1, and 0.0393 min−1 rate constants for the nanoparticles, pristine gC3N4, and the nanocomposite, respectively. This indicated an enhancement in the rate of reduction by the functionalized gC3N4 by 1.37- and 5.17-fold compared to the pristine gC3N4 and Cu3.21Bi4.79S9, respectively. A study of how the presence of other contaminants including dye (bisphenol A) and heavy-metal ions (Ag(I) and Pb(II)) in the system affects the photocatalytic process showed a reduction in the rate from 0.0393 min−1 to 0.0019 min−1 and 0.0039 min−1, respectively. Finally, the radical scavenging experiments showed that the main active species for the photocatalytic reduction of Cr(VI) are electrons (e−), hydroxyl radicals (·OH−), and superoxide (·O2−). This study shows the potential of functionalized gC3N4 as sustainable materials in the removal of hexavalent Cr from an aqueous solution.

Efficient photocatalytic degradation of emerging ciprofloxacin under visible light irradiation using BiOBr/carbon quantum dot/saponite composite

The use of visible-driven photocatalysts has fascinated attention as a capable and sustainable approach for wastewater remediation. In this work, BiOBr/carbon quantum dot (CQDs)/saponite composites (CQDs/Clay@BiOBr) were fabricated via hydrothermally using two different CQDs/Clay precursors (in-situ synthesis (IS) and physical mixing (PM)). The obtained products were characterized, and the photocatalytic performances of the prepared samples were evaluated in the photocatalytic decomposition of emerging ciprofloxacin (CIP) pharmaceutical waste. The highest CIP mineralization performance was achieved when a combination of BiOBr and CQDs/Clay (IS) with the appropriate proportion because the strong adhesion between CQDs and clay generate a great heterojunction in the composite. The stronger interaction of CQDs and better distribution of CQDs on the surface of clay in the CQDs/Clay (IS) enhanced the interaction of BiOBr and CQDs, and avoided the re-agglomeration of excess of CQDs on surface of BiOBr which reduce the active surface to receive the light and react with CIP. The ultrafast degradation rate of the optimized CQDs/Clay@BiOBr composite was better compared to others. The significant improvement in the CIP degradation efficiency of the CQDs/Clay@BiOBr composite was attributed to the excellent separation and transportation of photogenerated electrons and holes, as confirmed by photoluminescence, photocurrent density, and electrochemical impedance spectroscopy results. Moreover, the photocatalytic degradation mechanism of CIP in the CQDs/Clay@BiOBr composite was proposed based on the electronic states of each material in the composite and on a scavenger test. Thus, the proposed CQDs/Clay@BiOBr composite can be employed as a potential visible-light-driven photocatalyst for the decomposition of organic contaminants in wastewater.

Improving photocatalytic activity under visible light over a novel food wastes biochar-based BiOBr nanocomposite

Biochar (C) applied in synthesizing photocatalysts to eliminate water pollution has been intensively investigated. Herein we report the first use of biochar pyrolyzed from food wastes at 400 ^°C (400C) and 700 ^°C to construct C/BiOBr composites via a facile hydrolysis approach. Photocatalytic performances could be significantly improved by choosing the appropriate carbonization temperature and adjusting the content of C in C/BiOBr composites. The prepared 1%400C/BiOBr exhibited the best photodegradation capacity towards methylene orange (20 mg/L) and tetracycline (50 mg/L). A series of characterization results illustrated that smooth structure and surface properties (oxygen functional groups and persistent free radicals) of 400C played an important role in enhancing the photocatalytic activities. Mechanism exploration suggested that h⁺ and ˙O₂^- were the main active species thus contributing to photodegradation. This study provided a new insight into utilization of biochar derived from food wastes in photocatalysis and environmental remediation.

Cellulose Structures as a Support or Template for Inorganic Nanostructures and Their Assemblies

Cellulose is the most abundant natural polymer and deserves the special attention of the scientific community because it represents a sustainable source of carbon and plays an important role as a sustainable energent for replacing crude oil, coal, and natural gas in the future. Intense research and studies over the past few decades on cellulose structures have mainly focused on cellulose as a biomass for exploitation as an alternative energent or as a reinforcing material in polymer matrices. However, studies on cellulose structures have revealed more diverse potential applications by exploiting the functionalities of cellulose such as biomedical materials, biomimetic optical materials, bio-inspired mechanically adaptive materials, selective nanostructured membranes, and as a growth template for inorganic nanostructures. This article comprehensively reviews the potential of cellulose structures as a support, biotemplate, and growing vector in the formation of various complex hybrid hierarchical inorganic nanostructures with a wide scope of applications. We focus on the preparation of inorganic nanostructures by exploiting the unique properties and performances of cellulose structures. The advantages, physicochemical properties, and chemical modifications of the cellulose structures are comparatively discussed from the aspect of materials development and processing. Finally, the perspective and potential applications of cellulose-based bioinspired hierarchical functional nanomaterials in the future are outlined.

Nanocellulose for Sustainable Water Purification

Nanocelluloses (NC) are nature-based sustainable biomaterials, which not only possess cellulosic properties but also have the important hallmarks of nanomaterials, such as large surface area, versatile reactive sites or functionalities, and scaffolding stability to host inorganic nanoparticles. This class of nanomaterials offers new opportunities for a broad spectrum of applications for clean water production that were once thought impractical. This Review covers substantial discussions based on evaluative judgments of the recent literature and technical advancements in the fields of coagulation/flocculation, adsorption, photocatalysis, and membrane filtration for water decontamination through proper understanding of fundamental knowledge of NC, such as purity, crystallinity, surface chemistry and charge, suspension rheology, morphology, mechanical properties, and film stability. To supplement these, discussions on low-cost and scalable NC extraction, new characterizations including solution small-angle X-ray scattering evaluation, and structure-property relationships of NC are also reviewed. Identifying knowledge gaps and drawing perspectives could generate guidance to overcome uncertainties associated with the adaptation of NC-enabled water purification technologies. Furthermore, the topics of simultaneous removal of multipollutants disposal and proper handling of post/spent NC are discussed. We believe NC-enabled remediation nanomaterials can be integrated into a broad range of water treatments, greatly improving the cost-effectiveness and sustainability of water purification.

Waste preserved wood derived biochar catalyst for promoted peroxymonosulfate activation towards bisphenol A degradation with low metal ion release: The insight into the mechanisms

The rational disposal of waste preserved wood is of great significance since its embedded metals (Cu, As, and Cr) pose potential threat to environment and human health. In this study, a biochar catalyst derived from waste preserved wood (PWB) was prepared for the degradation of bisphenol A (BPA) via peroxymonosulfate (PMS) activation. The PWB exhibited prominent catalytic degradation capability towards BPA compared with common wood derived biochar (CWB). Further tests and analysis elucidated that both radical species (OH) and non-radical species (¹O₂) were generated by the PWB/PMS system, whereas only ¹O₂ was detected in CWB/PMS system. Specifically, the metal compounds, especially metallic Cu in the PWB activated PMS via radical pathway, and the CO groups in the biochar generated the non-radical pathway, the coexistence of which resulted in higher BPA degradation rate in PWB/PMS system. It was also demonstrated that the heavy metal ion leaching (As and Cr) in PWB/PMS system was negligible. Furthermore, the biochar could effectively inhibit the leakage of oxidized Cu ions. This study provides a novel approach to prepare high-efficient carbocatalysts for organic pollutant degradation in water, which also enables the waste preserved wood with an environmental nondestructive mode of dispatch.

Recent advances on nanocellulose biomaterials for environmental health photoremediation: An overview

As one of the potential bionanomaterials, nanocellulose has appeared as a favorable candidate for photoremediation of the environment because of its abundance in nature, inexpensive, eco-friendly, decomposable, high surface area, and outstanding mechanical properties. The current review carefully summarized the diverse type of nanocellulose, their preparation approaches, and several previous works on the use of nanocellulose for photoremediation. These include the role of nanocellulose for the increased surface active site of the hybrid photocatalysts by providing a large surface area for enhanced adsorption of photons and pollutant molecules, as a dispersing agent to increase distribution of metal/non-metal dopants photocatalysts, as well as for controlled size and morphology of the dopants photocatalysts. Furthermore, the recommendations for upcoming research provided in this review are anticipated to ignite an idea for the development of other nanocellulose-based photocatalysts. Other than delivering beneficial information on the present growth of the nanocellulose biomaterials photocatalysts, this review is expected will attract more interest to the utilization of nanocellulose photocatalyst and distribute additional knowledge in this exciting area of environmental photoremediation. This could be attained by considering that a review on nanocellulose biomaterials for environmental health photoremediation has not been described elsewhere, notwithstanding intensive research works have been dedicated to this topic.

Enhanced degradation of bisphenol A by mixed ZIF derived CoZn oxide encapsulated N-doped carbon via peroxymonosulfate activation: The importance of N doping amount

In this study, mixed metal cobalt zinc oxide embedded nitrogen enriched porous carbon composites (CoZnO-PC) were prepared via pyrolyzing polyvinylpyrrolidone (PVP) encapsulated Co, Zn-bimetal centered zeolitic imidazolate frameworks (ZIF). The prepared composites were then used to activate peroxymonosulfate (PMS) for bisphenol A (BPA) removal in water. When mole ratio of Co/Zn was 2/1, the resulted Co₂Zn₁O-PC possessed spinel structure with prominent degradation capability, in which the introduction of Zn accelerated the PMS activation performance of Co through establishing bimetal synergistic interactions. Both radical and non-radical activation pathways were existed in the Co₂Zn₁O-PC/PMS system, in which Co₂Zn₁O dominated the radical pathway whereas PC dominated the non-radical way. Since PVP contained abundant nitrogen atoms and could form strong coordination interactions with the ZIF precursor, the introduction of PVP in the ZIF precursor prevented pore collapsing during pyrolysis process, as well as enhancing the nitrogen content in the pyrolzed composites, which significantly promoted the generation of singlet oxygen. With combined pathways, the Co₂Zn₁O-PC/PMS system showed a wide pH application range with promising mineralization rate. Meanwhile, the spinel-structured Co₂Zn₁O-PC was magnetically separable with desirable recyclability. This study presents a novel composite with remarkable performance for the removal of refractory organic pollutants in municipal wastewater.

Construction of ZIF@electrospun cellulose nanofiber derived N doped metallic cobalt embedded carbon nanofiber composite as binder-free supercapacitance electrode

In this study, binder-free hybrid supercapacitance electrode based on N, Co co-doped porous carbon polyhedral encapsulated carbon nanofibers composites (N-Co/CNF) was prepared through pyrolyzing cobalt based zeolitic imidazolate frameworks (ZIF-67(Co)) incorporated electrospun cellulose nanofibers. With rational combination of the conductivity provided by cellulose derived CNF, promising porosity provided by CNF and ZIF-67(Co) derived porous carbon and uniformly dispersed metallic cobalt nanoparticles, the N-Co/CNF displayed excellent electrochemical properties. Specifically, the N-Co/CNF pyrolyzed at 800 °C possessed superior electrochemical performance in 1 M H₂SO₄ electrolyte, including a specific capacitance of ~433 F/g and 84% of the capacitance retention after 3000 consecutive charge-discharge cycles. This significantly exceeded the performance of cellulose derived CNF based pure carbonaceous electrode. Therefore, the present study provides a new view on the construction of high performance hybrid supercapacitance electrode which introduces renewable biomass resources like cellulose as both carbonaceous material precursors and conductive binders.

Polysaccharide-based (nano)materials for Cr(VI) removal

Chromium is a potentially poisonous and carcinogenic species, which originates from human activities and various industries such as leather, steel, iron, and electroplating industries. Chromium is present in various oxidation states, among which hexavalent chromium (Cr(VI)) is highly toxic as a natural contaminant. Therefore, chromium, particularly Cr(VI), must be eliminated from the environment, soil, and water to overcome significant problems due to its accumulation in the environment. There are different approaches such as adsorption, ion exchange, photocatalytic reduction, etc. for removing Cr(VI) from the environment. By converting Cr(VI) to Cr(III), its toxicity is reduced. Cr(III) is essential for the human diet, even in small amounts. Today, biopolymers such as alginate, cellulose, gum, pectin, starch, chitin, and chitosan have received much attention for the removal of environmental pollutants. Biopolymers, particularly polysaccharides, are very useful compounds due to their OH and NH₂ functional groups and some advantages such as biodegradability, biocompatibility, and accessibility. Therefore, they can be widely applied in catalytic applications and as efficient adsorbents for the removal of toxic compounds from the environment. This review briefly investigates the application of polysaccharide-based (nano)materials for efficient Cr(VI) removal from the environment using adsorption/reduction, photocatalytic, and chemical reduction mechanisms.

Enhanced Adsorption of Rhodamine B on Modified Oil-Based Drill Cutting Ash: Characterization, Adsorption Kinetics, and Adsorption Isotherm

In this paper, phosphoric acid (H₃PO₄), hydrochloric acid (HCl), and hydrogen peroxide (H₂O₂) were employed for the modification of oil-based drill cutting ash (OBDCA) for the first time. The adsorption of rhodamine B (RhB) on modified oil-based drill cutting ash (MOBDCA) in an aqueous medium was investigated. H₂O₂-modified OBDCA had the optimal adsorption efficiency for RhB. The physical and chemical properties of MOBDCA were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), ζ-potential, N₂ adsorption-desorption isotherm, and pore size distribution. The effect of the pH value (3-11), reaction time (10-720 min), and initial RhB concentration (10-200 mg/L) on RhB adsorption was discussed. The adsorption kinetics highly fitted with the pseudo-second-order model (R ² > 0.99), which indicated that the adsorption process was dominated by chemisorption. The adsorption isotherm fitted well with the Langmuir and Freundlich models (R ² > 0.97), which indicated the monolayer adsorption process and the heterogeneous adsorption process, respectively. The theoretic adsorption capacity (50 mg/g) for RhB was achieved by H₂O₂-modified OBDCA. This paper provides a promising method of resource utilization of OBDCA to treat organic pollutants.

Disassembly of lignocellulose into cellulose, hemicellulose, and lignin for preparation of porous carbon materials with enhanced performances

Lignocellulose is the primary component of many biomasses, including corn straw. Herein, lignocellulose in corn straw was disassembled into the individual polymers, cellulose, hemicellulose, and lignin via a mild and facile method. Subsequently, three porous carbon materials were prepared by carbonization and chemical activation of cellulose (PCCC), hemicellulose (PCHC), and lignin (PCLC). The three materials showed higher specific surface areas (2565.7, 2996.1, and 2590.3 m² g^-1) and higher porosities (1.4261, 1.5876, and 1.2406 cm³ g^-1) than that of PCCS, a porous carbon material derived from raw corn straw (1993 m² g^-1 and 1.19 cm³ g^-1). Of note, PCCC and PCHC exhibited higher adsorption (1025.5 and 950.1 mg g^-1) of brilliant green (BG), than PCCS (876.7 mg g^-1). Besides, the BG adsorption capacities of the designed materials were higher than that of most adsorbents, and 2-2.5 times higher than that of graphite oxide (416.7 mg g^-1). These study results indicate that the disassembly of lignocellulosic biomass into cellulose, hemicellulose, and lignin is an effective strategy for preparing various porous carbon materials with enhanced performances.

Electrospun Carbon Nanofibers from Biomass and Biomass Blends-Current Trends

In recent years, ecological issues have led to the search for new green materials from biomass as precursors for producing carbon materials (CNFs). Such green materials are more attractive than traditional petroleum-based materials, which are environmentally harmful and non-biodegradable. Biomass could be ideal precursors for nanofibers since they stem from renewable sources and are low-cost. Recently, many authors have focused intensively on nanofibers' production from biomass using microwave-assisted pyrolysis, hydrothermal treatment, ultrasonication method, but only a few on electrospinning methods. Moreover, still few studies deal with the production of electrospun carbon nanofibers from biomass. This review focuses on the new developments and trends of electrospun carbon nanofibers from biomass and aims to fill this research gap. The review is focusing on recollecting the most recent investigations about the preparation of carbon nanofiber from biomass and biopolymers as precursors using electrospinning as the manufacturing method, and the most important applications, such as energy storage that include fuel cells, electrochemical batteries and supercapacitors, as well as wastewater treatment, CO2 capture, and medicine.

Chronicle of Nanocelluloses (NCs) for Catalytic Applications: Key Advances

Nanocellulose (NC) is a biomaterial with growing interest in the field of nanocomposites and sustainable materials. NC has various applications including biodegradable materials, reinforcing agents, packaging films, transpiring membranes and medical devices. Among the many applications, the use of NC functionalized with organic and inorganic groups has found wide use as a catalyst in chemical transformations. The goal of this review is to collect the current knowledge on its catalytic applications for chemical groups conversion. We have chosen to organize the manuscript according to subdivision of NC into Bacterial Nanocellulose (BNC), Cellulose Nanocrystals (CNCs), and Cellulose Nanofibers (CNFs) and their role as inorganic- and organic-functionalized NC-catalysts in organic synthesis. However, in consideration of the fact that the literature on this field is very extensive, we have decided to focus our attention on the scientific productions of the last five years.

Coupling the fluorescence and adsorptive properties of biomass-based cellulose–CdS nanocomposite for the alleviation of water contaminants

Integration of CdS nanoparticles with CNF nanofibers for selective fluorescence detection of pharmaceutical waste and adsorptive elimination of textile and pesticide waste.

Green microwave synthesis of functionalized chitosan with robust adsorption capacities for Cr(VI) and/or RHB in complex aqueous solutions

Dinitrosalicylic acid-functionalized chitosan, CHN-DNSA, was developed and improved the adsorption property against chromium Cr(VI) and/or Rhodamine B (RHB). Here, the disposal of wastewater bearing Cr(VI) and RHB from a complex system was ascribed to significant differences in physicochemical properties. The constructed CHN-DNSA surface charge is responsible for different interactions enabling simultaneous capture of pollutants. The excellent adsorption potency of Cr(VI) at pH 3.0 was 98.4% within a remarkable 1 h and the adsorption performance was 91.1% for RHB. The ionic strength was affected, reducing the removal % of Cr(VI) to 36.7% whereas 0.1 M NaCl meliorated the removal efficiency from 91.6 to 96.2% for RHB and from 82.3 to 89.1% for a binary system. Also, the exploited elimination process of Cr(VI) and/or RHB obeyed the 2nd model of kinetics and the Freundlich system. Good recovery, superior capacity, and synthetic approach make this protocol promising for wastewater treatment.