An insight into the green synthesis of SiO2 nanostructures as a novel adsorbent for removal of toxic water pollutants

Wettability behavior of DTMS modified SiO2: Experimental and molecular dynamics study

In this research, the wetting behavior of SiO2 modified with dodecyltrimethoxysilane (DTMS) was explored using both experimental and molecular dynamics (MD) simulation approaches. The experimental results reveal that DTMS can chemically bond to the SiO2 surface, and the contact angle (CA) reaches the maximum value of 157.7° when the mass of DTMS is twice that of SiO2. The different wetting behaviors caused by DTMS grafting were analyzed by CA fitting, ionic pairs, concentration distribution, molecule orientation, and interfacial interaction energy. The results demonstrate that a 25 % DTMS grafting rate resulted in a maximum CA of 158.2°, which is ascribed to the disruption of interfacial hydrogen bonding and changes in the hydration structure caused by DTMS grafting. Moreover, the above hydrophobic SiO2 model shows a slight decrease in CA as the water temperature increases, which is consistent with the experimental findings. In contrast, an opposite change was observed for the pristine SiO2 model. Although the higher water temperature enhances the diffusion capacity of water molecules in both models, the difference in interfacial interactions is responsible for the change in CA. We hope this finding will contribute to a deeper understanding of the wetting adjustment of SiO2.

Polyethylene Glycol/Rice Husk Ash Shape-Stabilized Phase Change Materials: Recovery of Thermal Energy Storage Efficacy via Engineering Porous Support Structure

This study focuses on modifying the porous structure of acid-treated rice husk ash (ARHA) to enhance the thermal energy storage capacity of poly(ethylene glycol) (PEG) confined within shape-stabilized phase change materials. The modification process involved a cost-effective sol-gel method in which ARHA was initially dissolved in an alkaline solution and subsequently precipitated in an acidic environment. ARHA, being a mesoporous SiO2-based material with a high surface area but low pore volume, had limited capacity to adsorb PEG (50%). Furthermore, it hindered the crystallinity of impregnated PEG by fostering abundant interfacial hydrogen bonds (H-bonds), resulting in a diminished thermal energy storage efficiency. Following modification of the porous structure, the resulting material, termed mARHA, featured a three-dimensional macroporous network, providing ample space to stabilize a significant amount of PEG (70%) without any leakage. Notably, mARHA, with a reduced surface area, effectively mitigated interfacial H-bonds, consequently enhancing the crystallinity of impregnated PEG. This modification led to the recovery of thermal energy storage efficacy from 0 J/g for PEG/ARHA to 109.3 J/g for PEG/mARHA. Additionally, the PEG/mARHA composite displayed improved thermal conductivity, reliable thermal performance, and effective thermal management when used as construction materials. This work introduces a straightforward and economical strategy for revitalizing thermal energy storage in PEG composites confined within RHA-based porous supports, offering promising prospects for large-scale applications in building energy conservation.

Silica/Annona muricata nano-hybrid: Synthesis and anticancer activity against breast cancer

Biogenically derived silica nanoparticles may serve as a well-defined target vehicle for drug delivery and have a wide range of applications in biomedicine. Silica nanoparticles are an excellent candidate as drug carriers due to their mesoporous structure, high drug loading capacity, low toxicity, environmental friendliness and low economic synthesis procedures. In this study, nano structured silica was extracted from sugarcane bagasse through an alkali leaching extraction and conjugated with A. muricata extract overcoming its poor solubility and improving its bioavailability within the host system. The Silica Nanoparticles (SNP) and Annona muricata conjugated Silica Nanoparticles (AM/SNP) were characterized using SEM, FTIR, TGA, EDAX, XRD and zeta potential. The AM/SNP was subjected to kinetic release studies and exhibited a sustained release of 64 % over the course of 12 h in contrast to extract, indicating the slow release of the drug under synthetic conditions. A. muricata pose a high affinity against tumor cells as an anti-cancer agent, and the potential of binding was testified using in-silico virtual screening against breast cancer receptors with lead acetogenins with Annomuricin (-7.4 kcal/mol) and Gigantecin (-7.4 kcal/mol) exhibiting a high binding affinity against ER and HER2+ receptors respectively. The AM/SNP conjugate exhibited high cytotoxicity against the MCF-7 breast cancer cell line with an IC50 value of 33.43 μg, indicating high potency of the conjugate at low concentrations, facilitating low systemic toxicity on administration.

Comparative Study of Different Pretreatment and Combustion Methods on the Grindability of Rice-Husk-Based SiO2

The rice husk (RH) combustion pretreatment method plays a crucial role in the extraction of nanoscale SiO2 from RH as a silicon source. This study examined the effects of diverse pretreatment methods and combustion temperatures on the particle size distribution of nanoscale high-purity amorphous SiO2 extracted from rice husk ash (RHA) post RH combustion. The experiment was structured using the Taguchi method, employing an L9 (21 × 33) orthogonal mixing table. The median diameter (D50) served as the output response parameter, with the drying method (A), combustion temperature (B), torrefaction temperature (C), and pretreatment method (D) as the input parameters. The results showed the torrefaction temperature (C) as being the predominant factor affecting the D50, which decreased with an increasing torrefaction temperature (C). The optimal parameter combination was identified as A2B2C3D2. The verification test revealed that roasting could improve the abrasiveness of Rh-based silica and reduce the average particle size. Torrefaction at medium temperatures might narrow the size distribution range of RHA-SiO2. We discovered that the purity of silica increased with an increasing roasting temperature by evaluating the concentration of silica in the sample. The production of RHA with silica concentrations up to 92.3% was investigated. X-ray diffraction analysis affirmed that SiO2's crystal structure remained unaltered across different treatment methods, consistently presenting as amorphous. These results provide a reference for extracting high-value products through RH combustion.

Silica nanoparticles mediated insect pest management

Silicon is known for mitigating the biotic and abiotic stresses of crop plants. Many studies have proved beneficial effects of bulk silicon against biotic stresses in general and insect pests in particular. However, the beneficial effects of silica nanoparticles in crop plants against insect pests were barely studied and reported. By virtue of its physical and chemical nature, silica nanoparticles offer various advantages over bulk silicon sources for its applications in the field of insect pest management. Silica nanoparticles can act as insecticide for killing target insect pest or it can act as a carrier of insecticide molecule for its sustained release. Silica nanoparticles can improve plant resistance to insect pests and also aid in attracting natural enemies via enhanced volatile compounds emission. Silica nanoparticles are safe to use and eco-friendly in nature in comparison to synthetic pesticides. This review provides insights into the applications of silica nanoparticles in insect pest management along with discussion on its synthesis, side effects and future course of action.

Silicon nanoparticles: Comprehensive review on biogenic synthesis and applications in agriculture

Recent advancements in nanotechnology have opened new advances in agriculture. Among other nanoparticles, silicon nanoparticles (SiNPs), due to their unique physiological characteristics and structural properties, offer a significant advantage as nanofertilizers, nanopesticides, nanozeolite and targeted delivery systems in agriculture. Silicon nanoparticles are well known to improve plant growth under normal and stressful environments. Nanosilicon has been reported to enhance plant stress tolerance against various environmental stress and is considered a non-toxic and proficient alternative to control plant diseases. However, a few studies depicted the phytotoxic effects of SiNPs on specific plants. Therefore, there is a need for comprehensive research, mainly on the interaction mechanism between NPs and host plants to unravel the hidden facts about silicon nanoparticles in agriculture. The present review illustrates the potential role of silicon nanoparticles in improving plant resistance to combat different environmental (abiotic and biotic) stresses and the underlying mechanisms involved. Furthermore, our review focuses on providing the overview of various methods exploited in the biogenic synthesis of silicon nanoparticles. However, certain limitations exist in synthesizing the well-characterized SiNPs on a laboratory scale. To bridge this gap, in the last section of the review, we discussed the possible use of the machine learning approach in future as an effective, less labour-intensive and time-consuming method for silicon nanoparticle synthesis. The existing research gaps from our perspective and future research directions for utilizing SiNPs in sustainable agriculture development have also been highlighted.

Bioremediation of multifarious pollutants using laccase immobilized on magnetized and carbonyldiimidazole-functionalized cellulose nanofibers

An easily recyclable biocatalyst (Lac@CDI-MCNFs) was synthesized by immobilizing laccase on rice straw-derived carbonyldiimidazole mediated magnetized cellulose nanofibers (MCNFs). Lac@CDI-MCNFs were utilized for bioremediation of cefixime antibiotic (CT), carbofuran pesticide (CF) and safranin O dye (SO) via oxidation-reduction reactions in wastewater. MCNFs provided enhanced pH, temperature and storage stability to laccase and allowed reusability for up to 25 cycles with mere 20 % decline in efficacy. The Lac@CDI-MCNFs effectively degraded 98.2 % CT and 96.8 % CF into benign metabolites within 20 h and completely degraded SO in just 7 h. Response surface modelling (RSM) was employed based on the Box Behnken Design to evaluate the effect of various parameters i.e. pH, catalyst dosage and the pollutants concentration which was further validated with experimental studies. The degradation products were identified using LCMS, which allowed the degradation pathway of the pollutants to be determined. The degradation of all pollutants followed first- order kinetics with rate constants of 0.1775, 0.0832 and 0.958 h^-1 and half-life of 3.9, 5.0 and 0.723 h for CT, CF and SO, respectively. Lac@CDI-MCNFs was demonstrated to be an effective catalyst for the degradation of multifarious pollutants.

Highly efficient visible light active doped metal oxide photocatalyst and SERS substrate for water treatment

The development of efficient nanomaterials with promising optical and surface properties for multifunctional applications has always been a subject of novel research. In this work, the study of highly efficient TiO₂ nanorods (NRs) and Ta-doped TiO₂ NRs (Ta-TiO₂ NRs) synthesized by alkaline hydrothermal treatment followed by soaking treatment has been reported. NRs were investigated for their potential applications as recyclable/reproducible visible light active photocatalysts and surface-enhanced Raman scattering (SERS) substrates in wastewater treatment. NRs were characterized by various microscopic (scanning and transmission electron microscopy), spectroscopic (X-ray diffraction, X-ray photoelectron, UV-visible, photoluminescence, and Raman spectroscopy), and surface (Brunauer-Emmett-Teller) techniques. The NRs exhibited promising optical properties with a band gap of 2.95 eV (TiO₂ NRs) and 2.58 eV (Ta-TiO₂ NRs) showing excellent photo-degradation activities for methylene blue (MB) dye molecules under natural sunlight. Particularly, Ta-TiO₂ NRs showed enhanced response as visible light active photocatalysts in normal sunlight and also as SERS substrate attributed to the additional defects introduced by Ta doping. It could be explained by the combined effect of doping-induced enhanced visible light absorption and charge transfer (CT) properties of Ta-TiO₂ NRs. Furthermore, Ta-TiO₂ NRs were investigated for their long-term stability, reproducibility of the data, and recyclability in view of their potential applications in water treatment.

Rose bengal-decorated rice husk-derived silica nanoparticles enhanced singlet oxygen generation for antimicrobial photodynamic inactivation

Rice husks are well known for their high silica content, and the RH-derived silica nanoparticles (RH NPs) are amorphous and biocompatible; therefore, they are suitable raw materials for biomedical applications. In this study, rose bengal-impregnated rice husk nanoparticles (RB-RH NPs) were prepared for their potential photosensitization and ¹O₂ generation as antimicrobial photodynamic inactivation. RB is a halogen-xanthene type's photosensitizer showing high singlet oxygen efficiency, and the superior photophysical properties are desirable for RB in the antimicrobial photodynamic inactivation of bacteria. To enhance the binding of anionic RB to RH NPs, we conducted cationization for the RH NPs using polyethyleneimine (PEI). The control of the RB adsorption state on cationic PEI-modified RH NPs was essential for RB RH-NP photosensitizers to obtain efficient ¹O₂ generation. Minimizing RB aggregation allowed highly efficient ¹O₂ production from RB-RH NPs at the molar ratio of RB with the PEI, X_RB/PEI. = 0.1. The RB-RH NPs have significant antimicrobial activity against Streptococcus mutans compared to free RB after white light irradiation. The RB-RH NP-based antimicrobial photodynamic inactivation can be employed effectively in treating Streptococcus mutans for dental applications.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s10853-023-08194-z.

A Novel P@SiO2 Nano-Composite as Effective Adsorbent to Remove Methylene Blue Dye from Aqueous Media

This work aims to prepare a novel phosphate-embedded silica nanoparticles (P@SiO₂) nanocomposite as an effective adsorbent through a hydrothermal route. Firstly, a mixed solution of sodium silicate and sodium phosphate was passed through a strong acidic resin to convert it into hydrogen form. After that, the resultant solution was hydrothermally treated to yield P@SiO₂ nanocomposite. Using kinetic studies, methylene blue (MB) dye was selected to study the removal behavior of the P@SiO₂ nanocomposite. The obtained composite was characterized using several advanced techniques. The experimental results showed rapid kinetic adsorption where the equilibrium was reached within 100 s, and the pseudo-second-order fitted well with experimental data. Moreover, according to Langmuir, one gram of P@SiO₂ nanocomposite can remove 76.92 mg of the methylene blue dye. The thermodynamic studies showed that the adsorption process was spontaneous, exothermic, and ordered at the solid/solution interface. Finally, the results indicated that the presence of NaCl did not impact the adsorption behavior of MB dye. Due to the significant efficiency and promising properties of the prepared P@SiO₂ nanocomposite, it could be used as an effective adsorbent material to remove various cationic forms of pollutants from aqueous solutions in future works.

Recent advances in carbon-based nanomaterials for the treatment of toxic inorganic pollutants in wastewater

Wastewater contains inorganic pollutants, generated by industrial and domestic sources, such as heavy metals, antibiotics, and chemical pesticides, and these pollutants cause many environmental problems.

Surface functionalization of bamboo leave mediated synthesized SiO2 nanoparticles: Study of adsorption mechanism, isotherms and enhanced adsorption capacity for removal of Cr (VI) from aqueous solution

Green synthesis of nanoparticles (NPs) provides economic and environmental benefits as an alternative to chemical or physical methods. Furthermore, the surface properties of such NPs can be modulated by means of the functionalization with different groups making them suitable for various advanced functional applications including water pollutants removal using adsorption technique. In the present work, an eco-friendly synthesis route for nano-adsorbent SiO₂ NPs and subsequent surface modifications for enhanced adsorption capacity in removal of Cr(VI) ions from aqueous solution are reported. The green synthesis of SiO₂ NPs was carried out using simple bamboo leaves followed by surface modification with amine (A-SiO₂) and carboxylic (C-SiO₂) functional groups with aim to study the effect of functionalization on adsorption capacity. These nano-adsorbents were characterized by FTIR, SEM, XPS, BET, and zeta potential. and adsorption of Cr(VI) was studied at varying parameters i.e. NPs mass, contact time, and solution pH. The investigation shows interesting results revealing the importance of interactions between the surface functional groups on SiO₂ NPs and Cr(VI) species as well as experimental conditions for the choice of surface modifier to achieve a maximum adsorption capacity. The adsorption mechanism has been studied using Langmuir, Freundlich and Temkin adsorption isotherms. The maximum adsorption capacity has been achieved in the case of A-SiO₂ NPs which was found to 174 mg/g and much higher than that of SiO₂ and C-SiO₂ NPs attributed to the selective adsorption and pH conditions. Additionally, A-SiO₂ NPs exhibit excellent recyclability indicating their suitability for promising and long term potential applications. This study provides a novel, simple and cost-effective synthesis/surface engineering technology for producing high performance recyclable nano-adsorbents for adsorptive removal of Cr(VI).

TiO2 nanoflower photocatalysts: Synthesis, modifications and applications in wastewater treatment for removal of emerging organic pollutants

Titanium dioxide (TiO₂) has been considered as one of the most promising photocatalysts nanomaterials and is being used in a variety of fields of energy and environment under sunlight irradiation via photocatalysis. Highly efficient photocatalytic materials require the design of the proper structure with excellent morphology, interfacial structures, optical and surface properties, etc. Which are the key points to realize effective light-harvesting for photocatalytic applications. Hierarchical TiO₂ based nanoflower structures (i.e., 3D nanostructures) possess such characteristics and have attracted much attention in recent years. The uniqueness of TiO₂ nanoflowers (NFs) with a coarse texture and arranged structures demonstrates higher photocatalytic activity. This review deals with the hydrothermal synthesis of 3D TiO₂ NFs and effect of shape/size as well as various key synthesis parameters to improve their optoelectronic and photocatalytic properties. Furthermore, to improve their photocatalytic properties, various strategies such as doping engineering and heterojunction/nanocomposite formation with other functional nanomaterials have been discussed followed by their potential applications in photocatalytic degradation of various emerging pollutants discharged into the wastewater from various sources. Importance of such 3D nanoarchitecutres and future research in other fields of current interest in environments are discussed.