Silsesquioxanes: Novel compatibilizing agents for tuning the microstructure and properties of PLA/PCL immiscible blends

Interfacial distribution and compatibilization of imidazolium functionalized CNTs in poly(lactic acid)/polycaprolactone composites with excellent EMI shielding and mechanical properties

Imidazolium-functionalized polyurethane (IPU) functionalized multi-walled carbon nanotubes (CNTs) was used to control interfacial distribution and compatibilization of CNTs, and enhance electromagnetic interference (EMI) shielding and mechanical properties of poly(lactic acid)/polycaprolactone (PLA/PCL) based composites. IPU facilitated the uniformly dispersion of CNTs and induced the selectively location of CNTs at the interface and PCL phase, which is beneficial to build more effective three-dimensional network structure at the co-continuous interphase. The EMI shielding properties for the PLA/PCL/8CNT/0.8IPU composites have been evidently increased to 35.6 dB. Meanwhile, the elongation at break and the notched impact strength of the PLA/PCL/8CNT/0.8IPU composite reached 307.8 % and 51.3 kJ/m², respectively, which are increased by 27 and 53 % of PLA/PCL/8CNT because of the compatibilization effect of IPU and the distribution of CNTs. This work presented a promising prospect of polymer-based composites with satisfactory EMI shielding and mechanical properties.

Nanocomposite Materials Based on TMDCs WS2 Modified Poly(l-Lactic Acid)/Poly(Vinylidene Fluoride) Polymer Blends

Novel multifunctional biopolymer blend nanocomposites composed of poly(vinylidene fluoride)(PVDF) and tungsten disulfide nanotubes (INT-WS₂) that are layered transition metal dichalcogenides (TMDCs) were easily prepared by applying an economical, scalable, and versatile melt processing route. Furthermore, their synergistic effect to enhance the properties of poly(L-lactic acid) (PLLA) matrix was investigated. From morphological analysis, it was shown that the incorporation of 1D (INT)-WS₂ into the immiscible PLLA/PVDF mixtures (weight ratios: 80/20, 60/40, 40/60, and 20/80) led to an improvement in the dispersibility of the PVDF phase, a reduction in its average domain size, and consequently a larger interfacial area. In addition, the nanoparticles INT-WS₂ can act as effective nucleating agents and reinforcing fillers in PLLA/PVDF blends, and as such, greatly improve their thermal and dynamic-mechanical properties. The improvements are more pronounced in the ternary blend nanocomposites with the lowest PVDF content, likely due to a synergistic effect of both highly crystalline PVDF and 1D-TMDCs nano-additives on the matrix performance. Considering the promising properties of the developed materials, the inexpensive synthetic process, and the extraordinary properties of environmentally friendly and biocompatibe 1D-TMDCs WS₂, this work may open up opportunities to produce new PLLA/PVDF hybrid nanocomposites that show great potential for biomedical applications.

Preparation of hetero-armed POSS-cored star-shaped PCL-PLA/PLA composites and effect of different diisocyanates as compatibilizer

Eight-armed A₄B₄-type hetero-arm star-shaped PCL-PLA polymers ((PCL)₄-POSS-(PLA)₄, SPLA30) with POSS core were successfully prepared via combination of the "arm-first" approach utilizing ring-opening polymerization (ROP) and click chemistry techniques. Firstly, alkyne-functional PLA and PCL polymers having arms with 30 repeating units were synthesized via ROP with utilizing propargyl alcohol as initiator and stannous octoate (Sn(Oct)₂) as catalyst. Then, the obtained hetero-armed star-shaped polymers were prepared by Cu(I)-catalyzed alkyne-azide cycloaddition (CuAAC) click reaction between alkyne functional polymers (1:1 PCL:PLA) and azido functional polyhedral oligomeric silsesquoxane (POSS-(N₃)₈) molecules. Finally, these obtained star-shaped SPLA30 was blended with neat PLA at different PLA/SPLA30 ratios (95/5 and 90/10 wt%) via melt blending by utilizing micro-compounder (a lab-scale) to enhance thermal, morphological, and mechanical properties of neat PLA. Also, different diisocyanates (1,4-phenylene diisocyanate (PDI), isophorone diisocyanate (IPDI), methylene diphenyl diisocyanate (MDI), and toluene 2,4-diisocyanate (TDI)) at constant ratio (1 wt%) were used as a chain extender bonding terminal group of polymers. It was found that addition of SPLA30 and SPLA30+ diisocyanates provided improvements in mechanical properties (especially in elongation at break and impact strength) of neat PLA. When the thermal properties were examined, it was seen that the decomposition temperatures of the blends decreased significantly compared to neat PLA and that there was a significant increment in the T_g and T_m values. In addition, it has been found that especially the diisocyanates added to provide good interfacial adhesion with polymer blends and show a homogeneous distribution on the surface.

Effects of Organic Montmorillonite (OMMT) and Pre-Orientation on Property of Poly(l-lactic acid) (PLLA)/Ethylene Propylene Diene Monomer (EPDM) Blends

Poly(l-lactic acid)/ethylene propylene diene monomer/organic montmorillonite (PLLA/EPDM/OMMT) samples were melt-compounded and then processed into sheets via two routes, namely, compression-molding and calendering. Tensile performance, morphology, and thermal property of the samples were investigated. Tensile test showed that the incorporation of OMMT resulted in significant enhancement in the tensile ductility of the PLLA/EPDM samples. SEM observation revealed that EPDM domain size decreased largely with increasing OMMT loading, indicating the compatibility of OMMT with PLLA/EPDM blends. Moreover, the elongation at break, tensile yield strength, and modulus of the calendered samples were found to be much higher than those of the compression-molded samples. It can be attributed to the pre-oriented rigid amorphous fraction of PLLA matrix and pre-stretched EPDM phases in the calendered samples produced by the stretching/shearing effect of calendering. Compared to the spherical/ellipsoidal EPDM particles in the compression-molded samples, these stretched EPDM phases with higher aspect ratio in the calendered samples can be more effective to initiate craze, and terminate the craze growing to a crack along transversal direction. Therefore, the calendered samples show a better tensile ductility than the compression-molded ones. Moreover, annealing was carried out to increase the crystallinity of the samples. Tensile performance, morphology, and thermal property of the annealed samples were also systematically investigated.

Lipase mediated synthesis of polycaprolactone and its silica nanohybrid

In this study, rice husk ash (RHA) silanized with 3-glycidyloxypropyl trimethoxysilane was used as support material to immobilize Candida antarctica lipase B. The developed biocatalyst was then utilized in the ring opening polymerization (ROP) of ε-caprolactone and in situ development of PCL/Silica nanohybrid. The silanization degree of RHA was determined as 4 % (w) by thermal gravimetric analysis (TGA). Structural investigations and calculation of molecular weights of nanohybrids were realized by proton nuclear magnetic resonance (1H NMR). Crystallinity was determined by differential scanning calorimetry (DSC) and X-ray diffraction (XRD). Scanning Electron Microscopy (SEM) was used for morphological observations. Accordingly, the PCL composition in the nanohybrid was determined as 4 %, approximately. Short chained amorphous PCL was synthesized with a number average molecular weight of 4400 g/mol and crystallinity degree of 23 %. In regards to these properties, synthesized PCL/RHA composite can find use biomedical applications.

Poly (lactic acid) blends: Processing, properties and applications

Poly (lactic acid) or polylactide (PLA) is a commercial biobased, biodegradable, biocompatible, compostable and non-toxic polymer that has competitive material and processing costs and desirable mechanical properties. Thereby, it can be considered favorably for biomedical applications and as the most promising substitute for petroleum-based polymers in a wide range of commodity and engineering applications. However, PLA has some significant shortcomings such as low melt strength, slow crystallization rate, poor processability, high brittleness, low toughness, and low service temperature, which limit its applications. To overcome these limitations, blending PLA with other polymers is an inexpensive approach that could also tailor the final properties of PLA-based products. During the last two decades, researchers investigated the synthesis, processing, properties, and development of various PLA-based blend systems including miscible blends of poly l-lactide (PLLA) and poly d-lactide (PDLA), which generate stereocomplex crystals, binary immiscible/miscible blends of PLA with other thermoplastics, multifunctional ternary blends using a third polymer or fillers such as nanoparticles, as well as PLA-based blend foam systems. This article reviews all these investigations and compares the syntheses/processing-morphology-properties interrelationships in PLA-based blends developed so far for various applications.

Synthesis of well-defined star, star-block, and miktoarm star biodegradable polymers based on PLLA and PCL by one-pot azide-alkyne click reaction

Based on the "arm-first" strategy, ring-opening polymerization (ROP) and one-pot azide-alkyne click reaction, well-defined star-shaped polymers with different architectures have been successfully synthesized, including the star homopolymers four-arm star-shaped polycaprolactone (4sPCL) and four-arm star-shaped poly(l-lactic acid) (4sPLLA), star-block copolymer 4sPCL-b-PLLA and miktoarm star-shaped copolymer PCL2PLLA2. The star homopolymers 4sPCL and 4sPLLA were synthesized by a click reaction of an azide small molecule initiator and HC[triple bond, length as m-dash]C-PCL or HC[triple bond, length as m-dash]C-PLLA. The star-block copolymer 4sPCL-b-PLLA was synthesized by a click reaction of an azide small molecule initiator and the block copolymer HC[triple bond, length as m-dash]C-PCL-b-PLLA. The miktoarm star polymer PCL2PLLA2 was synthesized by a one-pot azide-alkyne click reaction of simultaneous addition of equal proportions of HC[triple bond, length as m-dash]C-PCL and HC[triple bond, length as m-dash]C-PLLA. The structures of these star-shaped polymers have been confirmed by NMR, FT-IR and GPC. Furthermore, the melting and crystallization behaviors investigated using DSC and WXRD also confirm the formation of star-shaped polymers with different architectures.

Graphite nanoplatelets-modified PLA/PCL: Effect of blend ratio and nanofiller localization on structure and properties

Structure and properties of poly(lactic acid) (PLA)/poly (ɛ-caprolactone) (PCL) influenced by graphite nanoplatelets (GNP) were studied in dependence on blend composition. Electron microscopy indicates predominant localization of GNP in PCL. GNP-induced changes in viscosity hinder refinement of PCL inclusions, support PCL continuity in the co-continuous system, and lead to reduction of PLA inclusions size without GNP being present at the interface in the PCL-matrix blend. Negligible differences in crystallinity of both phases indicate that mechanical behaviour is mainly influenced by reinforcement and GNP-induced changes in morphology. Addition of 5 parts of GNP leads to ~40% and ~25% increase of stiffness in the PCL- and PLA-matrix systems, respectively, whereas the reinforcing effect is practically eliminated in the co-continuous systems due to GNP-induced lower continuity of PLA which enhances toughness. Impact resistance of the 80/20 blend shows increase with 5 parts content due to synergistic effect of PCL/GNP stacks, whereas minor increase in the blend of the ductile PCL matrix with brittle PLA inclusions is caused by GNP-modification of the component parameters. Results indicate high potential of GNP in preparing biocompatible systems with wide range of structure and properties.

Hydrophobicity and polymer compatibility of POSS-modified Wyoming Na-montmorillonite for developing polymer-clay nanocomposites

The aim of the present work was to investigate the hydrophobicity and polymer compatibility of aminopropylisooctyl polyhedral oligomeric silsequioxane (POSS) - modified Na-montmorillonite (Na-MMT) towards developing polymer-clay nanocomposites. The effect of different concentrations of POSS on properties of Na-MMT was studied. The intercalation ability of the POSS molecules into the Na-MMT interlayer was analyzed by X-ray diffraction. It was found that the d₀₀₁ value was increased with increasing the POSS concentration, indicating the successful intercalation of the POSS molecules into the Na-MMT interlayer. The d₀₀₁ value was 4.12nm at 0.4 cation exchange capacity (CEC) loading of POSS, increased at a slight rate upon further increase of CEC loading, and finally reached 4.25nm at 1.0 CEC loading of POSS. The results of the thermogravimetric (TGA) analysis confirmed the high thermal stability of the POSS-MMT. The thermal stability was defined as a 5% mass loss (T₅) at 0.2 CEC loading of POSS was observed at 352°C and slightly decreased with further increase in the POSS concentration. The porous properties, such as specific surface area (SSA), pore volume, and pore size were estimated by the adsorption of N₂ molecules on the Na-MMT surface. The SSA and pore volume were reduced with increasing the concentration of the POSS molecules due to the adsorption of the POSS molecules on the Na-MMT, while the pore size was increased upon the formation of macroporous structure. The interfacial interaction energy between water and POSS-MMT (ΔG_{Clay/Water/Clay}^IF) was used to evaluate the surface hydrophobicity, and a similar approach was also applied to assess the polymer compatibility of the developed composite. The obtained results confirm that the polymer compatibility of POSS-MMT prepared in this study is better than that of commonly used HDTMA-MMT.

A Novel Electrostimulated Drug Delivery System Based on PLLA Composites Exploiting the Multiple Functions of Graphite Nanoplatelets

A novel drug delivery system based on poly(l-lactide) (PLLA), graphite, and porphyrin was developed. In particular, 5,10,15,20-tetrakis(4-hydroxyphenyl)porphyrin (THPP) was chosen because, besides its potential as codispersing agent of graphite, it is a pharmacologically active molecule. Graphite nanoplatelets, homogeneously dispersed in both the neat PLLA and the PLLA/porphyrin films, which were prepared by solution casting, turned out to improve the crystallinity of the polymer. Moreover, IR measurements demonstrated that unlike PLLA/porphyrin film, where the porphyrin was prone to aggregate causing variable concentration throughout the sample, the system containing also GNP was characterized by a homogeneous dispersion of the above molecule. The effect of graphite nanoplatelets on the thermal stabilization, electrical conductivity, and improvement of mechanical properties of the polymer resulted to be increased by the addition of the porphyrin to the system, thus demonstrating the role of the molecule in ameliorating the filler dispersion in PLLA. The porphyrin release from the composite film, occurring both naturally and with the application of an electrical field, was measured using an UV-vis spectrophotometer. Indeed, voltage application turned out to improve significantly the kinetic of drug release. The biocompatibility of the polymer matrix as well as the mechanical and thermal properties of the composite together with its electrical response makes the developed material extremely promising in biological applications, particularly in the drug delivery field.

Synergistic effects in mechanical properties of PLA/PCL blends with optimized composition, processing, and morphology

Blending of poly(lactic acid) with poly(ε-caprolactone) can increase the impact strength above the values of the individual components.

Compatibilization strategies in poly(lactic acid)-based blends

Recent compatibilization strategies in poly(lactic acid)-based blends have been reviewed in this paper.