Effect of re-crystallization on tensile, optical and water vapour barrier properties of corn starch films containing fatty acids

Tailoring hydroxypropyl starch films with curdlan for enhanced properties for edible packaging

Hydroxypropyl starch-based composite system has high potential for many applications such as food packaging and biomedical fields. Here, how the incorporation of curdlan, a thermo-irreversible heating-set gel, tailors the processability, structure, and film performance of hydroxypropyl starch, a cooling-set gel, has been systematically investigated, aiming to achieve enhanced material properties favorable for edible packaging applications. Curdlan incorporation increased the shear-thinning behavior and viscosity of hydroxypropyl starch solution, which was also strongly affected by temperature. The miscibility and comparability between the two polymers with distinct gelation behaviors is a practical and interesting scientific topic. Scanning electron microscopy, dynamic mechanical analysis, and thermogravimetric analysis all indicated good compatibility between hydroxypropyl starch and curdlan. There was no observable phase boundary between the two materials, and all composite films showed only a single relaxation peak and only one polymer thermal decomposition peak. This resulted in improved structural density and overall performance. Compared with pure HPS film, the 7:3 HPS/CD film showed increases in tensile strength by 66.12 % and thermal decomposition temperature by 3 °C, and a reduction in water solubility by 11.72 %. This knowledge gained here may facilitate the development of edible films based on hydroxypropyl starch with satisfying film performance and processability.

Structure and properties of starch - BaSO4 composite obtained using mechanical activation techniques

The aim of this study is to obtain and characterize starch films structurally modified by in situ precipitation of BaSO4 combined with mechanical activation of casting dispersion in a rotor-stator device. By the rheological method, it was found that the modification causes a decrease in the ability of casting dispersions to structure over time. Composite films with a filler content of 0 %-15 % (w/w) were characterized using optical and SEM microscopy, FT-IR spectroscopy, and tensile and moisture resistance testing data. The maximum increase in strength (by 70 %) and elongation at break (by 870 %) is achieved with a filler content of 5 % and 15 %, respectively. An increase in the filler content to 5 % causes an increase in starch recrystallization rate, but at concentrations above 5 % of BaSO4, it inhibits retrogradation. The films obtained by mechanical activation with optimized parameters were uniformly translucent, had lower water vapor permeability than films made from starch alone, had high flexibility, and did not warp or shrink. The developed high-performance, environmentally friendly method can be recommended for the large-scale production of starch-based composite materials.

Preparation and characterization of a novel high barrier mulching film with tunicate cellulose nanocrystals/sodium alginate/alkali lignin

In this study, the base film (CSL) was prepared by blending tunicate cellulose nanocrystals (TCNCs) extracted from tunicate shells, with sodium alginate (SA) and alkali lignin (AL). Then, the mulching film (CSL-WK) was prepared using water-borne polyurethane (WPU) as binder to install low-energy Kaolin on the surface of CSL film. The influences of composition with different concentrations on mechanical properties were studied. The tensile strength and elongation at break of CSL-WK film could reach 86.58 MPa and 50.49 %, respectively. The mulching films were characterized by degradability test, SEM, FTIR, and TGA. TCNCs had good compatibility with SA and AL, and a rough structure was formed on the surface of the film to improve the hydrophobicity. The barrier properties, including ultraviolet resistance, water contact angle, water vapor permeability, water retention, and flame retardancy, were tested. The results showed that CSL-WK films could block 97 % of ultraviolet light, reduce about 25 % of soil water loss, and self-extinguish within 7 s of open flame ignition. Note that the secondary spraying method significantly improved the barrier property of films. This study lays a foundation for the preparation of ecologically friendly, biodegradable, and high barrier mulching film, and expands the application of marine resources.

Development, characterization and application of starch-based film containing polyphenols of piper betle L. waste in chicken meat storage

The current study aimed to develop a sustainable solution to extend the shelf life of chicken meat by developing starch-based functional film embedded with polyphenolic extract of waste petioles of betel leaf (BLP). The results showed that loading of the extract significantly (p < 0.05) improved flexibility, thickness, water solubility, DPPH radical scavenging activity, and UV light protection ability by enhancing intermolecular interactions among potato starch, guar gum, and the extract. The developed film showed optimum mechanical and water barrier properties at a 4% BLP extract concentration computed through TOPSIS method (A multi-criteria decision-making approach). During the shelf life study, the extract embedded film maintained the quality of chicken meat for up to 12 days at refrigerated temperature. Biodegradation time of the extract-blended films was considerably decreased to 14 days from 28 days for the native film, indicating suitable alternative to non-biodegradable film for storing the raw meat.

Cassava Starch Films Containing Quinoa Starch Nanocrystals: Physical and Surface Properties

Quinoa starch nanocrystals (QSNCs), obtained by acid hydrolysis, were used as a reinforcing filler in cassava starch films. The influence of QSNC concentrations (0, 2.5, 5.0, 7.5 and 10%, w/w) on the film's physical and surface properties was investigated. QSNCs exhibited conical and parallelepiped shapes. An increase of the QSNC concentration, from 0 to 5%, improved the film's tensile strength from 6.5 to 16.5 MPa, but at 7.5%, it decreased to 11.85 MPa. Adequate exfoliation of QSNCs in the starch matrix also decreased the water vapor permeability (~17%) up to a 5% concentration. At 5.0% and 7.5% concentrations, the films increased in roughness, water contact angle, and opacity, whereas the brightness decreased. Furthermore, at these concentrations, the film's hydrophilic nature changed (water contact angle values of >65°). The SNC addition increased the film opacity without causing major changes in color. Other film properties, such as thickness, moisture content and solubility, were not affected by the QSNC concentration. The DSC (differential scanning calorimetry) results indicated that greater QSNC concentrations increased the second glass transition temperature (related to the biopolymer-rich phase) and the melting enthalpy. However, the film's thermal stability was not altered by the QSNC addition. These findings contribute to overcoming the starch-based films' limitations through the development of nanocomposite materials for future food packaging applications.

Self-healing properties of retrograded starch films with enzyme-treated waxy maize starch as healing agent

Waxy maize starch (WMS) was modified using sequential α-amylase and transglucosidase to create enzyme-treated waxy maize starch (EWMS) with higher branching degree and lower viscosity as an ideal healing agent. Self-healing properties of retrograded starch films with microcapsules containing WMS (WMC) and EWMS (EWMC) were investigated. The results indicated that EWMS-16 had the maximum branching degree of 21.88 % after transglucosidase treatment time of 16 h, and A chain of 12.89 %, B1 chain of 60.76 %, B2 chain of 18.82 % and B3 chain of 7.52 %. The particle sizes of EWMC ranged from 2.754 to 5.754 μm. The embedding rate of EWMC was 50.08 %. Compared to retrograded starch films with WMC, water vapor transmission coefficients of retrograded starch films with EWMC were lower, while tensile strength and elongation at break values of retrograded starch films were almost similar. Retrograded starch films with EWMC had higher healing efficiency of 58.33 % as compared to that Retrograded starch films retrograded starch films with WMC was 44.65 %.

Fabrication of nanocellulose fibril-based composite film from bamboo parenchyma cell for antimicrobial food packaging

The development of nanocellulose fibril (NCF)-based films for use in food packaging has aroused tremendous attention because of their good biodegradability. In this work, NCFs isolated from bamboo parenchyma cell were used to fabricate the composite film with embedded silver nanoparticles (AgNPs). Results demonstrate that the low content of AgNPs, especially at content of 0.1 wt% in the composite film could slightly improve the tensile strength and Young's modulus of the composite film by about 11.0%, owing to the reduced thickness of cellulose crystallites and decreased amount of adsorbed water, as well as the increment in crystallinity and the hydrogen-bond intensity confirmed by X-ray diffraction measurement and Fourier transform infrared spectra. On the other hand, high content of AgNPs could enhance antimicrobial activity and thermal stability while showed negligible negative effect on tensile properties. Specifically, the maximum inhibition zone of the composite film (with AgNPs content of 0.1 wt%) was 13.5 ± 0.8 mm against Salmonella typhi (S. typhi) and 7.5 ± 0.3 mm against Escherichia coli (E. coli). The strong antimicrobial activity of NCF-based films highlights their potential as a biodegradable food packaging material.

An Overview of the Alternative Use of Seaweeds to Produce Safe and Sustainable Bio-Packaging

In modern times, seaweeds have become widely involved in several biotechnological applications due to the variety of their constituent bioactive compounds. The consumption of seaweeds dates to ancient times; however, only from the last few decades of research can we explain the mechanisms of action and the potential of seaweed-derived bioactive compounds, which has led to their involvement in food, cosmetic, pharmaceutical, and nutraceutical industries. Macroalgae-derived bioactive compounds are of great importance as their properties enable them to be ideal candidates for the production of sustainable “green” packaging. Diverse studies demonstrate that seaweed polysaccharides (e.g., alginates and carrageenans) not only provide health benefits, but also contribute to the production of biopolymeric film and biodegradable packaging. The dispersion of plastics and microplastics in the oceans provoke serious environmental issues that influence ecosystems and aquatic organisms. Thus, the sustainable use of seaweed-derived biopolymers is now crucial to replace plasticizers with biodegradable materials, and thus preserve the environment. The present review aims to provide an overview on the potential of seaweeds in the production of bioplastics which might be involved in food or pharmaceutical packaging.

Current Research and Applications of Starch-Based Biodegradable Films for Food Packaging

The use of biodegradable packaging material as an alternative to conventional petrochemical-based polymers is based on the environmental issues associated with conventional materials. This review aims to update the existing knowledge regarding the application of starch-based biodegradable films for food packaging. From the review, it was evident that starch stands out among biopolymers due to its abundance and cost effectiveness. This review is the first of its kind, having reviewed over 100 articles/publications on starch-based biodegradable films, consolidating their current state of research and their applications for food packaging; therefore, this review provides an insight into the utilization of nanomaterials to improve the shelf life of packaging of food.

Advancements in Biodegradable Active Films for Food Packaging: Effects of Nano/Microcapsule Incorporation

Food packaging plays a fundamental role in the modern food industry as a main process to preserve the quality of food products from manufacture to consumption. New food packaging technologies are being developed that are formulated with natural compounds by substituting synthetic/chemical antimicrobial and antioxidant agents to fulfill consumers' expectations for healthy food. The strategy of incorporating natural antimicrobial compounds into food packaging structures is a recent and promising technology to reach this goal. Concepts such as "biodegradable packaging", "active packaging", and "bioactive packaging" currently guide the research and development of food packaging. However, the use of natural compounds faces some challenges, including weak stability and sensitivity to processing and storage conditions. The nano/microencapsulation of these bioactive compounds enhances their stability and controls their release. In addition, biodegradable packaging materials are gaining great attention in the face of ever-growing environmental concerns about plastic pollution. They are a sustainable, environmentally friendly, and cost-effective alternative to conventional plastic packaging materials. Ultimately, a combined formulation of nano/microencapsulated antimicrobial and antioxidant natural molecules, incorporated into a biodegradable food packaging system, offers many benefits by preventing food spoilage, extending the shelf life of food, reducing plastic and food waste, and preserving the freshness and quality of food. The main objective of this review is to illustrate the latest advances in the principal biodegradable materials used in the development of active antimicrobial and antioxidant packaging systems, as well as the most common nano/microencapsulated active natural agents incorporated into these food-packaging materials.

Egg Yolk Oil as a Plasticizer for Polylactic Acid Films

Polylactic acid (PLA) is known to be one of the most extensively used biodegradable thermoplastic polyesters, with the potential to replace conventional petroleum-based packaging materials; however, the low flexibility of films prepared using PLA has limited the applications of this biopolymer. In this study, in order to improve the mechanical properties of PLA films and to provide them with antioxidant properties, egg yolk oil was used as a biobased plasticizer. For this purpose, PLA films with increasing concentrations of egg yolk oil were prepared and the effects of this oil on the light transmission, transparency, colour, water vapour permeability, solubility, antioxidant activity and mechanical properties of the films were characterized. In addition, electron microscopy of the structure of the transverse section of the films was also performed. Results showed that the formulations with higher concentrations of egg yolk oil increased the films’ elasticity, and their light barrier and antioxidant properties. Finally, in order to test the films as a packaging material for food applications, extra virgin olive oil and resveratrol, both photosensitive compounds, were packed and exposed to ambient light. Overall, the results show the potential of egg yolk oil as an environmentally friendly plasticizer that can improve the flexibility of PLA films and provide them with additional photoprotective properties.

Enhancing the dispersibility of multiwalled carbon nanotubes within starch-based films by the use of ionic surfactants

The incorporation of carbon-based nanomaterials into biopolymer matrix, to provide mechanical reinforcement and to obtain electrically conductive bionanocomposites, requires the homogeneous dispersion of the fillers. Herein, it is investigated the influence of surfactant structures on the dispersibility of multiwalled carbon nanotubes (MWNT) within starch matrix. Three different ionic surfactants, sodium dodecyl sulphate (SDS), cetyltrimethylammonium bromide (CTAB) and sodium cholate (SC), are employed to disperse the MWNT. Films with MWNT-SC show better dispersibility and an increase of about 75% of tensile strength and 60% of Young's modulus compared with films using MWNT-SDS and MWNT-CTAB. Nevertheless, MWNT functionalized with CTAB impart the highest values of antioxidant activity (scavenging activity around 30% in 1.5 h) and electrical conductivity (σ =14.75 S/m) to starch matrix. The properties of starch-based films can be tailored according to the physical adsorption of each surfactant on MWNT surface and/or the interfacial interaction of the surfactant with starch chains.

Comparative study on physicochemical properties of starch films prepared from five sweet potato (Ipomoea batatas) cultivars

Five different sweet potato (Ipomoea batatas) cultivars (Daeyumi, Gogeonmi, Sincheonmi [SCM], Singeonmi, and Sinyulmi [SYM]) were used to extract sweet potato starch (SPS) for developing starch-based films. After the chemical composition and amylose contents of all SPSs were evaluated, the morphological, moisture, mechanical, and barrier properties of the SPS-based films were investigated. As one of the film characteristics, the X-ray diffractograms revealed that the SCM-based film with the highest amylose content (26.34%) had the highest relative crystallinity (24.31%). The SCM-based film also showed higher tensile strength (3.05-fold) and elastic modulus (2.38-fold) than the SYM-based film with the lowest amylose content (21.84%). The water vapor and oxygen permeabilities of the SPS-based films were negatively correlated with the amylose content. Thus, the SCM-based film was less permeable for water vapor (3.16-fold) and oxygen (1.81-fold) than the SYM-based film. These results demonstrated that the sweet potato cultivar, especially the amylose content, plays a significant role in determining the physicochemical properties of the SPS-based films.

Development of Ginkgo (Ginkgo biloba) Nut Starch Films Containing Cinnamon (Cinnamomum zeylanicum) Leaf Essential Oil

There have been many studies on the development biodegradable films using starch isolated from various food sources as a substitute for synthetic plastic packaging films. In this study, starch was extracted from ginkgo (Ginkgo biloba) nuts, which were mainly discarded and considered an environment hazard. The prepared starch (GBS) was then used for the preparation of antioxidant films by incorporating various amounts of cinnamon (Cinnamomum zeylanicum) essential oil (CZEO), which provides antioxidant activity. The prepared GBS films with CZEO were characterized by measuring physical, optical, and thermal properties, along with antioxidant activity (ABTS, DPPH, and FRAP) measurements. With the increasing amount of CZEO, the flexibility and antioxidant activities of the GBS films increased proportionally, whereas the tensile strength of the films decreased. The added CZEO also increased the water vapor permeability of the GBS films, and the microstructure of the GBS films was homogeneous overall. Therefore, the obtained results indicate that the developed GBS films containing CZEO are applicable as antioxidant food packaging.

Functionality and Applicability of Starch-Based Films: An Eco-Friendly Approach

The accumulation of high amounts of petro-based plastics is a growing environmental devastation issue, leading to the urgent need to innovate eco-safe packaging materials at an equivalent cost to save the environment. Among different substitutes, starch-based types and their blends with biopolymers are considered an innovative and smart material alternative for petrol-based polymers because of their abundance, low cost, biodegradability, high biocompatibility, and better-quality film-forming and improved mechanical characteristics. Furthermore, starch is a valuable, sustainable food packaging material. The rising and growing importance of designing starch-based films from various sources for sustainable food packaging purposes is ongoing research. Research on "starch food packaging" is still at the beginning, based on the few studies published in the last decade in Web of Science. Additionally, the functionality of starch-based biodegradable substances is technically a challenge. It can be improved by starch modification, blending starch with other biopolymers or additives, and using novel preparation techniques. Starch-based films have been applied to packaging various foods, such as fruits and vegetables, bakery goods, and meat, indicating good prospects for commercial utilization. The current review will give a critical snapshot of starch-based films' properties and potential applicability in the sustainable smart (active and intelligent) new packaging concepts and discuss new challenges and opportunities for starch bio composites.

Design of Chitosan and Alginate Emulsion-Based Formulations for the Production of Monolayer Crosslinked Edible Films and Coatings

This study aimed to develop edible monolayer emulsion-based barriers with polysaccharides as film-forming components (chitosan and sodium alginate), soy lecithin as a surfactant and olive oil as a hydrophobic barrier. Monolayer barriers in the form of films were prepared by casting filmogenic emulsions composed of 2% w/v chitosan (dissolved in lactic acid 1% v/v) or 1% w/v sodium alginate, with different lipid contents (25, 50 and 100% w/w biopolymer basis) and different surfactant concentrations (5, 10 and 25% w/w, lipid basis). Glycerol was used as a plasticizer (25 % w/w, biopolymer basis). After the emulsion drying process, the obtained stand-alone films were sprayed with a crosslinking solution, achieving an optimized crosslinker content of 3.2 mgCa²⁺/cm² alginate film and 4 mg tripolyphosphate/cm² chitosan film. The effect of oil and lecithin contents, as well the presence of crosslinking agents, on the film’s water vapour permeability (WVP), water vapour sorption capacity, mechanical properties and colour parameters, was evaluated. The results have shown that the lowest WVP values were obtained with formulations containing 25% lipid and 25% surfactant for chitosan films, and 100% lipid and 25% surfactant for alginate films. The application of the crosslinking agents decreased even further the WVP, especially for chitosan films (by 30%). Crosslinking also increased films’ resistance to deformation under tensile tests. Overall, the films developed present a good potential as polysaccharide-based barriers with increased resistance to water, which envisages the use of the designed formulations to produce either edible/biodegradable films or edible coatings.

Effect of lipids with different physical state on the physicochemical properties of starch/gelatin edible films prepared by extrusion blowing

The effects of various physical state lipids (rapeseed oil (RO), shortening (ST), beeswax (BW)), on the physicochemical properties of starch (S) (hydroxypropyl distarch phosphate (HP), oxidized hydroxypropyl starch (OS))/gelatin (G) blown films were studied. S/G-lipid blends showed decreased storage modulus and complex viscosity. The formation of hydrogen bonds was inhibited by the ST and BW, but facilitated by the RO. Compared with BW and ST, RO was more effective to promote the melted and fractured of starch. Lipids addition promoted the compatibility of starch and gelatin. The presence of the lipids significantly improved the surface hydrophobicity, mechanical, water vapor barrier and water resistance properties of S/G films. S/G-RO films exhibited the strongest surface hydrophobicity and tensile strength, while HP/G-BW film showed the strongest water resistance and water vapor barrier properties. These results revealed that the appropriate lipids could be used to produce S/G-lipid films with desirable physicochemical properties.

Effect of cellulose and starch fatty acid esters addition on microstructure and physical properties of arabinoxylan films

Arabinoxylan (AX) and cellulose were extracted from wheat straw, whereas starch was extracted from potato peel. Thereafter, cellulose and starch were esterified with lauric, myristic, palmitic and stearic acids to prepare corresponding cellulose (CFAs) and starch fatty acid esters (SFAs) with DS 2.1-2.8. XRD study revealed remarkable loss of crystallinity in cellulose and starch due to fatty acid esterification. The addition of palmitate and stearate esters of cellulose and starch to AX formed laminar film microstructures which limited water vapor permeability whereas films prepared by blending AX with laurate and myristate esters of starch and cellulose were less effective as water vapor barrier due to their non-layer microstructures. The laminar structures also resulted significant reduction in mechanical strength of the composite films. Furthermore, all AX-CFAs and AX-SFAs films were thermally more stable than native composite films. These films might be used to produce industrially useful coating material for food products.

Insights into the miscibility characteristics of plastic-mimetic polypeptide with hydroxypropylmethylcellulose: Investigation of thermal degradability and intermolecular interactions

In this investigation, we integrated the parent recurring sequence of the plastic-derived polypeptide, poly[0.8(AVGVP),0.2(AEGVP)] (A, V, G, P, and E represents Alanine, Valine, Glycine, Proline, and Glutamic acid respectively) followed by characterization with inverse transition temperature, ¹³C, and ¹H-NMR spectroscopy. The miscibility attributes of poly[0.8(AVGVP),0.2(AEGVP)] with Hydroxypropylmethylcellulose was examined both in aqueous and solid-phase. The Huggins' co-efficient [K_H], the intrinsic viscosity [η], the interaction parameters ΔB and μ suggested by Chee, ΔK and β recommended by Jiang and Han, α by Sun, Δ[η]_m by Garcia showed that the polypeptide was miscible with HPMC in all proportions. DSC studies revealed single T_g values, and TGA manifested the enhanced thermal stability for all the proportions compared with their individuals. Further, verified the results by SEM and XRD. The FTIR evidenced existence of intermolecular hydrogen bonding between the two constituent polymers that caused the miscible blend system.

Comparison of physicochemical and mechanical properties of edible films made from navy bean and corn starches

BACKGROUND

Recently, there has been a great interest in developing new applications of edible dry beans (Phaseolus vulgaris L.). The utilization of starch, comprising the major component of dry bean seeds, for the preparation of edible films has just emerged.

RESULTS

In the present study, we chose navy bean as a model dry bean source, isolated its starch component, prepared edible films with different formulations (35 and 40 g L^-1 ), and compared these with the films made using isolated and commercial corn starches. Sunflower oil at 10 g L^-1 was dispersed into film-forming solution to design composite films. The water vapor barrier property, mechanical properties and microstructure of starch films from navy bean and corn were studied to evaluate their potential for use in food packaging. All of the films had smooth and uniform surface and were transparent.

CONCLUSION

Navy bean starch film showed physicochemical and mechanical properties comparable to corn starch films, and the addition of sunflower oil could further improve the water vapor barrier and mechanical properties of films. The findings obtained in the present study demonstrate the potential of using navy bean starch to prepare edible films. © 2020 Society of Chemical Industry.

Essential Oil-Containing Polysaccharide-Based Edible Films and Coatings for Food Security Applications

The wastage of food products is a major challenge for the food industry. In this regard, the use of edible films and coatings have gained much attention due to their ability to prevent the spoilage of the food products during handling, transport, and storage. This has effectively helped in extending the shelf-life of the food products. Among the various polymers, polysaccharides have been explored to develop edible films and coatings in the last decade. Such polymeric systems have shown great promise in microbial food safety applications. The inclusion of essential oils (EOs) within the polysaccharide matrices has further improved the functional properties of the edible films and coatings. The current review will discuss the different types of polysaccharides, EOs, methods of preparing edible films and coatings, and the characterization methods for the EO-loaded polysaccharide films. The mechanism of the antimicrobial activity of the EOs has also been discussed in brief.

Preparation of formyl cellulose and its enhancement effect on the mechanical and barrier properties of polylactic acid films

Cellulose was modified by formic acid to prepare formyl cellulose (FC). The amount of formyl groups in FC was adjusted by controlling the reaction time, reaction temperature, and formic acid concentration. Then, FC was used to reinforce polylactic acid (PLA) films prepared by solution casting. Scanning electron microscopy (SEM) shows that long rod-like cellulose particles were broken into short rods after formylation and the introduction of FC made PLA surface rougher. The mechanical properties of PLA/FC films were improved by the inclusion of FC. Compared to pure PLA film, the PLA/FC composite film with 1 wt% FC (containing 15.79% formyl groups) showed a 48.59% increase in tensile strength and a 346% increase in Young's modulus. The addition of FC also resulted in better water barrier properties. The moisture absorption capacity and water vapor permeability were 40.56% and 51.43% lower than those of the pure-PLA film. The enhancement in properties for PLA/FC composites could be ascribed to the improved compatibility between PLA and cellulose with the introduction of hydrophobic formate groups. The PLA/FC composite films developed in this work could be highly potential for food packaging.

Antimicrobial Activity and GC-MS Profile of Copaiba Oil for Incorporation into Xanthosoma mafaffa Schott Starch-Based Films

The present study evaluated the effect of the incorporation of copaiba oil, in direct and in microencapsulated form, into films based on Xanthosoma mafaffa Schott starch. Initially, the characterization of copaiba oil by gas chromatograph coupled with mass spectrometry (GC-MS) and its antimicrobial activity against gram-positive and gram-negative bacteria was performed. The films were produced by the casting technique and characterized in relation to physical, chemical, structural, and antimicrobial activity. Sesquiterpenes, mainly β-caryophyllene, were the predominant compounds in copaiba oil, showing antimicrobial activity against B. subtilis and S. aureus. The films showed forming capacity, however, was observed a decrease in solubility and revealed an increase in hydrophobic characteristics. However, the oil reduced the tensile strength and elongation, while the microcapsules did not influence the mechanical properties in comparison to the control film. From microstructure analysis, changes in the films roughness and surface were observed after the addition of oil both directly and in microencapsulated form. Films incorporated with microparticles were able to inhibit the gram-positive bacteria tested, forming inhibition zones, indicating that the encapsulation of copaiba oil was more efficient for protecting bioactive compounds from the oil, suggesting the possible application of mangarito starch-based films incorporated with copaiba oil as biodegradable packaging.

A Comprehensive Review on Corn Starch-Based Nanomaterials: Properties, Simulations, and Applications

Corn (Zea mays L.) is one of the major food crops, and it is considered to be a very distinctive plant, since it is able to produce a large amount of the natural polymer of starch through its capacity to utilize large amounts of sunlight. Corn starch is used in a wide range of products and applications. In recent years, the use of nanotechnology for applications in the food industry has become more apparent; it has been used for protecting against biological and chemical deterioration, increasing bioavailability, and enhancing physical properties, among other functions. However, the high cost of nanotechnology can make it difficult for its application on a commercial scale. As a biodegradable natural polymer, corn starch is a great alternative for the production of nanomaterials. Therefore, the search for alternative materials to be used in nanotechnology has been studied. This review has discussed in detail the properties, simulations, and wide range of applications of corn starch-based nanomaterials.

Chitin Pickering Emulsion for Oil Inclusion in Composite Films

A film containing a stable and well-dispersed hydrophobic phase in a surfactant-free bio-based hydrophilic matrix is proposed. In this study, an aqueous suspension of rod-like chitin nanocrystals (ChiNCs), mixed with paraffin oil, form an oil-in-water Pickering emulsion with a droplet diameter of 3 μm. These emulsions mixed with a 5 wt% starch solution formed homogeneous composite films by solvent casting. Various amounts of emulsion were incorporated, leading to self-supported films with a volume of oil as high as 45 vol%, with less than 1% of ChiNCs. This model inclusion system leads to droplets homogeneously dispersed throughout the composite films, as revealed by microscopy (SEM and CLSM) with mechanical properties controlled by the matrix. Finally, the droplets were easily released from the matrix by enzymatic hydrolysis. This easy-to-implement transparent film proved to be a good candidate when it is desirable to disperse a poor water-soluble component in a hydrophilic edible matrix.

Tailoring the surface properties and flexibility of starch-based films using oil and waxes recovered from potato chips byproducts

Agrofood byproducts may be exploited as a source of biomolecules suitable for developing bioplastic materials. In this work, the feasibility of using starch, oil, and waxes recovered from potato chips byproducts for films production was studied. The recovered potato starch-rich fraction (RPS) contained an amylopectin/amylose ratio of 2.3, gelatinization temperatures varying from 59 to 71 °C, and a gelatinization enthalpy of 12.5 J/g, similarly to a commercial potato starch (CPS). Despite of its spherical and oval granules identical to CPS, RPS had a more amorphous structure and gave rise to low viscous suspensions, contradicting the typical B-type polymorph crystal structure and sluggish dispersions of CPS, respectively. When used for films production, RPS originated transparent films with lower roughness and wettability than CPS-based films, but with higher stretchability. In turn, when combined with RPS and CPS, oil or waxes recovered from frying residues and potato peels, respectively, allowed to develop transparent yellowish RPS- and CPS-based films with increased surface hydrophobicity, mechanical traction resistance, elasticity, and/or plasticity. Therefore, potato chips industry byproducts revealed to have thermoplastic and hydrophobic biomolecules that can be used to efficiently develop biobased plastics with improved surface properties and flexibility, opening an opportunity for their valorization.

Dextrin Nanocomposites as Matrices for Solid Dosage Forms

Safe application of water-insoluble acaricides requires fast release from solid dosage systems into aquatic environments. Dextrin is a water-soluble form of partially hydrolyzed starch, which may be used as matrix material for these systems if retrogradation can be inhibited by the inclusion of nanofillers. Several glycerol-plasticized thermoplastic dextrin-based nanocomposites were prepared with a twin-screw extrusion-compounding process. The nanofillers included a layered double hydroxide (LDH), cellulose nanofibers (CNF), and stearic acid. The time-dependent retrogradation of the compounds was monitored by X-ray diffraction (XRD) and dynamic mechanical thermal analysis (DMA). XRD showed that composite samples that included stearic acid in the formulation led to the formation of an amylose-lipid complex and a stable crystallinity during aging. The most promising nanocomposite included both stearic acid and CNF. It was selected as the carrier material for the water-insoluble acaricide Amitraz. Fast release rates were observed for composites containing 5, 10, and 20% (w/w) of the pesticide. A significant reduction in the particle size of the released Amitraz powder was observed, which is ascribed to the high-temperature compounding procedure.

Use of Aloe Vera Gel-Based Edible Coating with Natural Anti-Browning and Anti-Oxidant Additives to Improve Post-Harvest Quality of Fresh-Cut ‘Fuji’ Apple

Recently, there is increasing use of edible and biodegradable films and packaging that are both environmentally friendly and functional for storage and market distribution. Fresh-cut ‘Fuji’ apples, harvested in an organic farm, were treated, using a spraying technique, with three new edible coatings based on Aloe vera gel (AVG—40% v/w) and in combination with natural additives: lemon essential oil (LEO—1% v/w) and hydroxypropyl methylcellulose (HPMC—0.1% v/w) and compared with untreated sample (CTR), the physicochemical and sensory characteristics and the proximate compounds were evaluated. During cold storage, weight loss, soluble solids content, and color of uncoated slices were reduced, while softening, ripening, browning, and acidity were accelerated. In contrast, the AVG/HPMC treatment significantly delayed the above parameters related to post-harvest quality loss, while the AVG/LEO treatment delayed the browning processes, maintaining an excellent color during cold storage. Concerning proximate compounds, the treatments did not alter their concentration in the fruit tissues. Sensory analyses revealed no detrimental effect on taste, aroma, or flavor. Our data evidenced the positive effect of Aloe vera gel in combination with LEO and HPMC on fresh-cut apple quality as an innovative and sustainable technique to maintain fresh-cut apple quality.

Edible films based on aqueous emulsions of low-methoxyl pectin with recovered and purified sunflower waxes

BACKGROUND

Edible films were obtained from aqueous emulsions prepared with low-methoxyl pectin at different concentrations (10, 20 and 30 g kg^-1 ) and two sunflower wax samples recovered from two waste samples of filter cakes produced in the winterization process of sunflower oil. The two sunflower waxes samples recovered (from the normal hybrid, NSFW, and from the high-oleic hybrid, HOSFW) were added in three proportions (0.1, 0.2 and 0.3 g g^-1 of pectin). Films were evaluated according to their structure, water resistance, water vapor permeability, mechanical properties and thermal behavior.

RESULTS

In general, good dispersion of the lipid material was observed in the cross-sections of the film. Increase in the water resistance (lower swelling index and water adsorption) was associated with a greater pectin content crosslinked with Ca²⁺ and the hydrophobic nature of waxes. The reduction in water vapor transfer rates was influenced by the effect of the wax addition, their fatty acid composition and their good distribution on the film. More resistant, rigid and less flexible films were obtained with lower pectin content, finding an inverse relationship between tensile strength and elongation percentage values.

CONCLUSION

These results evidence a promising alternative in the development of innovative strategies to valorize sunflower waxes derived from waste material. © 2020 Society of Chemical Industry.

Synthesis, characterization, and antimicrobial efficacy of composite films from guar gum/sago starch/whey protein isolate loaded with carvacrol, citral and carvacrol-citral mixture

The aim of this research was to formulate antimicrobial, composite films of guar gum, sago starch, and whey protein isolate for the prophylaxis of the bacterial gastroenteritis. The model antibacterial agents incorporated were essential oils, namely, carvacrol, citral and their combination. The films became darker and brownish in color due to the entrapment of the oils. The surface of the oil-entrapped films was more rough and coarse compared to the control film. Confocal micrographs affirmed the uniform distribution of the oil droplets within the biopolymeric network. The highest crystallite size and lowest lattice strain were estimated in the citral-containing film. FTIR analysis demonstrated that the incorporation of citral increased the proportion of the β-sheet structures of the whey protein isolate within the film matrix. However, the film formulation containing combination of carvacrol and citral demonstrated the lowest water vapor transmission rate (WVTR), highest tensile strength, Young's modulus and work to failure. All the oil-containing films demonstrated good antibacterial potency against the model bacterial gastroenteritis causing bacteria, namely, Bacillus cereus and Escherichia coli. In gist, it can be concluded that the prepared antimicrobial films could be used for the prophylaxis of the bacterial gastroenteritis.