Enhancement of physicochemical properties of whey protein-stabilized nanoemulsions by interfacial cross-linking using cinnamaldehyde

Physical and biological properties of alginate-based cinnamon essential oil nanoemulsions: Study of two different production strategies

Nanoemulsions are a promising alternative for essential oil incorporation into active coatings. The influence of the preparation steps order on nanoemulsions' physical properties is still little explored. This study aimed to analyze the effect of the sequence of preparation steps and of the oil and polymer concentration on the stability, physical properties, and antifungal activity of alginate-based cinnamon essential oil nanoemulsions. The nanoemulsions were produced by two strategies: (I) preparation directly into an alginate solution (Ultra-Turrax at 10,000 rpm for 5 min + Ultrasound 150 W for 3 min); and (II) preparation in water (Ultra-Turrax at 10,000 rpm for 5 min + Ultrasound 150 W for 3 min) followed by homogenization with a sodium alginate solution (Ultra-Turrax at 10,000 rpm for 1, 3 or 5 min). The nanoemulsion prepared by the second strategy showed better stability, physical properties, and antifungal activity. In general, the presence of alginate hindered the cavitation effects of ultrasound, leading to the increase of droplets size and consequently affecting emulsions stability, turbidity, and antifungal properties.

Effect of cinnamaldehyde-nanoemulsion and nanostructured lipid carriers on physicochemical attributes of reduced-nitrite sausages

This study aimed to produce cinnamaldehyde (CA)-loaded nanostructured lipid carriers (NLC) and nanoemulsion (NE) to replace nitrite in sausage. The NLC and NE droplet sizes were 132 and 116 nm with encapsulation efficiency of 98 and 96 %, respectively. In in vitro antimicrobial assessment, the free CA and NE showed higher microbial activity against S. aureus and E. coli than NLC. Meanwhile, NE showed a faster release profile for CA than NLC. Among the samples, NE and NE + nitrite indicated the lowest peroxide value (3.7 ± 0.1), TVBN amount (8.6 ± 0.2), acidity (0.3 ± 0.02), microbial quality (against E. coli, C. perfringens, lactic acid bacteria, psychrophilic bacteria, total mold and yeast, and total viable counts), and sensory attribute, while the NE + nitrite sample exhibited better color properties and higher oxymyoglobin content (5-10 % higher). Therefore, NE + nitrite can be the best choice due to supporting the different quality parameters of sausage.

Bacteriostatic Pickering emulsions stabilized by whey protein isolate-vanillin nanoparticles: Fabrication, characterization and stability in vitro

The purpose of this work was to prepare Pickering emulsion stabilized by bacteriostatic whey protein isolate-vanillin (WPI-Van) nanoparticles as a carrier for encapsulating vitamin E. The particle size, ζ potential, PDI were used to study the optimal preparation conditions of nanoparticles. The results showed that the optimal preparation condition was achieved at WPI/Van mass ratio of 3:1. FTIR spectra demonstrated the complexation of WPI and Van. SEM image showed spherical and slightly rough surface of nanoparticles. Inhibitory effects of nanoparticles on E. coli and S. aureus were also observed. After storage of 21 days at 4 °C, the retention rate of vitamin E in the emulsions remained 43% higher than that of unencapsulated vitamin E. Moreover, the release rate of vitamin E encapsulated in emulsions in the small intestine was 81%, indicating excellent bioaccessibility. The research can provide a new insight for production and application of antibacterial Pickering emulsions.

Ultrasonic and homogenization: An overview of the preparation of an edible protein-polysaccharide complex emulsion

Emulsion systems are extensively utilized in the food industry, including dairy products, such as ice cream and salad dressing, as well as meat products, beverages, sauces, and mayonnaise. Meanwhile, diverse advanced technologies have been developed for emulsion preparation. Compared with other techniques, high-intensity ultrasound (HIUS) and high-pressure homogenization (HPH) are two emerging emulsification methods that are cost-effective, green, and environmentally friendly and have gained significant attention. HIUS-induced acoustic cavitation helps in efficiently disrupting the oil droplets, which effectively produces a stable emulsion. HPH-induced shear stress, turbulence, and cavitation lead to droplet disruption, altering protein structure and functional aspects of food. The key distinctions among emulsification devices are covered in this review, as are the mechanisms of the HIUS and HPH emulsification processes. Furthermore, the preparation of emulsions including natural polymers (e.g., proteins-polysaccharides, and their complexes), has also been discussed in this review. Moreover, the review put forward to the future HIUS and HPH emulsification trends and challenges. HIUS and HPH can prepare much emulsifier-stable food emulsions, (e.g., proteins, polysaccharides, and protein-polysaccharide complexes). Appropriate HIUS and HPH treatment can improve emulsions' rheological and emulsifying properties and reduce the emulsions droplets' size. HIUS and HPH are suitable methods for developing protein-polysaccharide forming stable emulsions. Despite the numerous studies conducted on ultrasonic and homogenization-induced emulsifying properties available in recent literature, this review specifically focuses on summarizing the significant progress made in utilizing biopolymer-based protein-polysaccharide complex particles, which can provide valuable insights for designing new, sustainable, clean-label, and improved eco-friendly colloidal systems for food emulsion. PRACTICAL APPLICATION: Utilizing complex particle-stabilized emulsions is a promising approach towards developing safer, healthier, and more sustainable food products that meet legal requirements and industrial standards. Moreover, the is an increasing need of concentrated emulsions stabilized by biopolymer complex particles, which have been increasingly recognized for their potential health benefits in protecting against lifestyle-related diseases by the scientific community, industries, and consumers.

Thoroughly review the recent progresses in improving O/W interfacial properties of proteins through various strategies

Along with the future food market developing world widely, the personalized nutrition and rational function food design are found to be urgently attracted. Oil in a water (O/W) emulsion system has an excellent ability to maintain nutraceuticals and thus plays a promising role in producing future functional foods. Understanding the interfacial related mechanisms involved are essential for improving the quality of food products. Protein can effectively reduce interfacial tension and stable immiscible phases. The interfacial properties of proteins directly affect the emulsion qualities, which have gradually become a prospective topic. This review will first briefly discuss the interfacial-related fundamental factors of proteins. Next, the paper thoroughly overviewed current physical and chemical strategies tailored to improving the interfacial and emulsion properties of proteins. To be summarized, a higher flexibility could allow protein to be more easily unfolded and adsorbed onto the interface but could also possibly form a softer interfacial film. Several physical strategies, such as thermal, ultrasound and especially high-pressure homogenization are well applied to improve the interfacial properties. The interfacial behavior is also altered by various green chemical strategies, such as pH adjustment, covalent modification, and low molecular weight (LMW) surfactant addition. These strategies upgraded emulsion properties by increasing adsorption load, accelerating diffusion and adsorption rate, associated with lowering interfacial tension, and promoting interfacial protein interactions. Future researches targeted at elucidating interfacial-bulk protein interactions, unraveling interfacial behavior through in silico tools, exploring connection between interfacial-industrial processing properties, and clarifying the interfacial-sensory-digestive relationships of O/W emulsions is needed to develop emulsion applications.

Eugenol nanoemulsion inactivates Listeria monocytogenes, Salmonella Enteritidis, and Escherichia coli O157:H7 on cantaloupes without affecting rind color

Listeria monocytogenes, Salmonella Enteritidis, and Escherichia coli O157:H7 are the major foodborne pathogens that have been implicated in outbreaks related to consumption of contaminated cantaloupes. Current chlorine-based decontamination strategies are not completely effective for inactivating the aforementioned pathogens on cantaloupes, especially in the presence of organic matter. This study investigated the efficacy of eugenol nanoemulsion (EGNE) wash treatments in inactivating L. monocytogenes, Salmonella spp., and E. coli O157:H7 on the surface of cantaloupes. In addition, the efficacy of EGNE in inhibiting the growth of the three pathogens on cantaloupes during refrigerated and room temperature storage of 5 days was investigated. Moreover, the effect of EGNE wash treatment on cantaloupe color was assessed using a Miniscan® XE Plus. The EGNE was prepared with either Tween 80 (TW) or a combination of Gum arabic and Lecithin (GA) as emulsifiers. The cantaloupe rind was washed with EGNE (0.3, 0.6, and 1.25%), in presence or absence of 5% organic load, for 1, 5, or 10 min at 25°C. Enumeration of surviving pathogens on cantaloupe was performed by serial dilution and plating on Oxford, XLD or SMA agar followed by incubation at 37°C for 24–48 h. EGNE-GA and EGNE-TW wash significantly reduced all three pathogens by at least 3.5 log CFU/cm2 as early as 5 min after treatment. EGNE-GA at 1.25% inactivated L. monocytogenes, E. coli O157:H7 and S. Enteritidis on cantaloupes to below the detectable limit within 5 and 10 min of treatment, respectively (~4 log CFU/cm2, P < 0.05). EGNE treatments significantly reduced the survival of L. monocytogenes, S. Enteritidis, and E. coli O157:H7 on cantaloupe by at least 6 log CFU/cm2 at day 5 of storage at 25 and 4°C (P < 0.05). Presence of organic matter did not modulate the antimicrobial efficacy of nanoemulsion treatments (P > 0.05). EGNE treatments did not affect the rind color of cantaloupes (P > 0.05). In conclusion, eugenol nanoemulsions could potentially be used as a natural sanitizer to inactivate foodborne pathogens on cantaloupes. Further investigations in an industry setting are warranted.

A review of recent progress in improving the bioavailability of nutraceutical-loaded emulsions after oral intake

Increasing awareness of the health benefits of specific constituents in fruits, vegetables, cereals, and other whole foods has sparked a broader interest in the potential health benefits of nutraceuticals. Many nutraceuticals are hydrophobic substances, which means they must be encapsulated in colloidal delivery systems. Oil-in-water emulsions are one of the most widely used delivery systems for improving the bioavailability and bioactivity of these nutraceuticals. The composition and structure of emulsions can be designed to improve the water dispersibility, physicochemical stability, and bioavailability of the encapsulated nutraceuticals. The nature of the emulsion used influences the interfacial area and properties of the nutraceutical-loaded oil droplets in the gastrointestinal tract, which influences their digestion, as well as the bioaccessibility, metabolism, and absorption of the nutraceuticals. In this article, we review recent in vitro and in vivo studies on the utilization of emulsions to improve the bioavailability of nutraceuticals. The findings from this review should facilitate the design of more efficacious nutraceutical-loaded emulsions with increased bioactivity.

Effects of tocopherols on the stability of flaxseed oil-in-water emulsions stabilized by different emulsifiers: Interfacial partitioning and interaction

The potential effects of tocopherols (100 μM in emulsions) on the physicochemical stability of whey protein isolate (WPI), soy lecithin (SL), or Tween 20 (TW) stabilized flaxseed oil (FO)-in-water emulsions were investigated. During the storage (18 days at 55 ℃), the particle size, microstructure, and multiple light scattering results showed WPI-stabilized emulsions exhibited better physical stability when tocopherols were added hydroperoxides and TBARS concentration in TW-stabilized emulsions were higher than those of SL or WPI, which were suppressed differently by tocopherols. Among homologues, δ-tocopherol was more effective in inhibiting lipid oxidation than α-tocopherol, which was related to the higher interface partitioning. Moreover, the increased interfacial tension indicated tocopherols, especially δ-tocopherol, were adsorbed on the interface and interacted with WPI or SL via hydrophobic or electrostatic interactions determined by isothermal titration calorimetry. Our results suggest tocopherols are more applicable in WPI emulsion systems to achieve steady-state delivery of ALA.

Study on the emulsification and oxidative stability of ovalbumin-pectin-pumpkin seed oil emulsions using ovalbumin solution prepared by ultrasound

Pumpkin seed oil (PSO), which is a valuable compound with high nutritional value used for the prevention of various chronic diseases, is prone to oxidation. In this work, small and uniform (su) ovalbumin (OVA) and pectin (PEC) were used to stabilize PSO in the form of an emulsion. The results showed that suOVA-PEC-PSO emulsion with a droplet size of 9.82 ± 0.05 μm was successfully self-assembled from PSO, PEC, and suOVA solution (with a droplet size of 230.13 ± 14.10 nm) treated with 300 W ultrasound, owing to the formation of a more stable interfacial film on the surface of droplets. The interfacial, rheological, emulsifying, and antioxidant properties of the suOVA-PES-PSO emulsions were excellent, owing to the synergistic effects between PEC and suOVA solution. Moreover, the physical stability of the suOVA-PEC-PSO emulsions to salt stress, a freeze-thaw cycle, and heat treatment was also increased and the oxidation of linolenic acid was notably delayed. These results have extended the food-related applications of OVA and PSO, and provide a promising foundation for further exploration of the self-assembly of composite emulsions by small and uniform proteins.

Development of Salt- and Gastric-Resistant Whey Protein Isolate Stabilized Emulsions in the Presence of Cinnamaldehyde and Application in Salad Dressing

Protein-stabilized emulsions tend to be susceptible to droplet aggregation in the presence of high ionic strengths or when exposed to acidic gastric conditions due to a reduction of the electrostatic repulsion between the protein-coated droplets. Previously, we found that incorporating cinnamaldehyde into the oil phase improved the resistance of whey protein isolate (WPI)-stabilized emulsions against aggregation induced by NaCl, KCl and CaCl2. In the current study, we aimed to establish the impact of cinnamaldehyde on the tolerance of WPI-stabilized emulsions to high salt levels during food processing and to gastric conditions. In the absence of cinnamaldehyde, the addition of high levels of monovalent ions (NaCl and KCl) to WPI-emulsions cause appreciable droplet aggregation, with the particle sizes increasing from 150 nm to 413 nm and 906 nm in the presence of NaCl and KCl, respectively. In contrast, in the presence of 30% cinnamaldehyde in the oil phase, the WPI-emulsions remained stable to aggregation and the particle size of emulsions kept within 200 nm over a wide range of salt concentrations (0-2000 mM). Divalent counter-ions promoted droplet aggregation at lower concentrations (≤20 mM) than monovalent ones, which was attributed to ion-binding and ion-bridging effects, but the salt stability of the WPI emulsions was still improved after cinnamaldehyde addition. The incorporation of cinnamaldehyde into the oil phase also improved the resistance of the WPI-coated oil droplets to aggregation in simulated gastric fluids (pH 3.1-3.3). This study provides a novel way of improving the resistance of whey-protein-stabilized emulsions to aggregation at high ionic strengths or under gastric conditions.

Cinnamon Essential Oil Nanocellulose-Based Pickering Emulsions: Processing Parameters Effect on Their Formation, Stabilization, and Antimicrobial Activity

This work aimed to prepare nanocellulose-based Pickering emulsions using cinnamon essential oil. Different formulations were investigated by varying the preparation time, homogenization speed, oil and nanocellulose concentration, and morphology. The emulsions were first characterized by droplet size, morphologies, and storage stability. The Design of Experiments (DoE) was used to evaluate the parameter’s effects on the emulsions’ stability, and the emulsions with optimum particle size and stability were evaluated by antimicrobial activity. The more stable emulsions required higher energy in the system to obtain efficient emulsification. The cellulose nanocrystal (CNC) emulsions showed a 30% oil volume as a constant to obtain a low creaming index (34.4% and 42.8%) and zeta potential values around −29 mV, indicating an electrostatic stabilization. The cellulose nanofiber (CNF) emulsions showed 100% stability after a month using a 20% oil volume as a constant and Zeta potential values around −15 mV, indicating a steric stabilization. CNF-emulsions’ inhibition halos for Bacilus subtilis were 30.1 ± 3.7% smaller than those found in CNC-emulsions (65 ± 2.9 mm), while Pseudomonasaeruginosas almost do not present differences in the inhibition halos. These results suggest that the nanocellulose morphology may promote a regulation on the EO migration to the medium, as well that this migration ratio does not affect the bacteria.

Structural modification of whey protein isolate by cinnamaldehyde and stabilization effect on β-carotene-loaded emulsions and emulsion gels

The effect of cinnamaldehyde (CA) on the structure and properties of whey protein isolate (WPI) was investigated. The resultant WPI/CA complex was used as stabilizer to form emulsions and emulsion gels, which were used for the delivery and protection of β-carotene. The particle size and hydrophobicity of WPI solution increased and then decreased with the addition of CA. Circular dichroism showed that CA mainly changed the secondary structure of WPI, with increasing β-fold content from 47.2% to 72.9%. The fluorescence spectra showed that both tryptophan and tyrosine in WPI were involved in the interaction with CA. WPI/CA complex as the stabilizer could form the stable emulsions and emulsion gels, which showed better protection effect on β-carotene, and helped enhance its bioaccessibility. The knowledge provides insights into the development of new multifunctional food ingredients and the enhancement of protein modification in food system.

Fabrication of Oil-in-Water Emulsions with Whey Protein Isolate-Puerarin Composites: Environmental Stability and Interfacial Behavior

Protein–polyphenol interactions influence emulsifying properties in both directions. Puerarin (PUE) is an isoflavone that can promote the formation of heat-set gels with whey protein isolate (WPI) through hydrogen bonding. We examined whether PUE improves the emulsifying properties of WPI and the stabilities of the emulsions. We found that forming composites with PUE improves the emulsifying properties of WPI in a concentration-dependent manner. The optimal concentration is 0.5%, which is the highest PUE concentration that can be solubilized in water. The PUE not only decreased the droplet size of the emulsions, but also increased the surface charge by forming composites with the WPI. A 21 day storage test also showed that the maximum PUE concentration improved the emulsion stability the most. A PUE concentration of 0.5% improved the stability of the WPI emulsions against environmental stress, especially thermal treatment. Surface protein loads indicated more protein was adsorbed to the oil droplets, resulting in less interfacial WPI concentration due to an increase in specific surface areas. The use of PUE also decreased the interfacial tension of WPI at the oil–water interface. To conclude, PUE improves the emulsifying activity, storage, and environmental stability of WPI emulsions. This result might be related to the decreased interfacial tension of WPI–PUE composites.

Enhancing the oxidative stability of algal oil emulsions by adding sweet orange oil: Effect of essential oil concentration

The effects of sweet orange essential oil (SOEO) concentration (0-12.5% of oil phase) on the physical stability, oxidative stability, and interfacial composition of algal oil-in-water emulsions containing sodium caseinate-coated oil droplets was examined. SOEO addition had no influence on the microstructure and physical stability of the algal oil emulsions. The addition of SOEO enhanced the oxidation stability of algal oil emulsion. As an example, the values of algal oil emulsions with 0 and 10% SOEO were 198 and 100 mmol/kg algal oil after 16 days of accelerated oxidation, respectively. The absorbed protein level was higher in the algal oil emulsion containing 10% SOEO (70%) than in 0% SOEO (57%). This result suggested that the presence of SOEO enhanced the interfacial thickness, possibly by interacting with the casein molecules. A thicker protein layer may have helped to retard the oxidation of the omega-3 oils inside lipid droplets.

Effect of sesamol on the physical and chemical stability of plant-based flaxseed oil-in-water emulsions stabilized by proteins or phospholipids

Plant-based polyphenols are increasingly being explored as functional ingredients in emulsified food systems. In this study, the effects of sesamol on the physical and chemical stability of flaxseed oil-in-water emulsions stabilized by either phospholipids (sunflower) or proteins (whey or pea) were investigated. In the absence of sesamol, the protein-based emulsions displayed better physical stability than the phospholipid-based ones, which was related to their smaller particle diameter and higher particle charge. For the phospholipid-based emulsions, sesamol addition did not improve their physical stability, but it did inhibit lipid oxidation. In particular, it decreased the formation of secondary oxidation products, with a 65% reduction in TBAR formation compared to the control after 8 days of storage. For the protein-based emulsions, sesamol addition reduced particle aggregation and inhibited lipid oxidation, reducing the secondary oxidation products by around 85% after 19 days of storage. The inhibitory efficiency of sesamol in the pea protein-based emulsions was comparable to that in the whey protein-based ones. The effects of sesamol on the physical and chemical stability of the emulsions were related to its partitioning between the oil, water, and interfacial layers. This study suggests that adding sesamol to plant-based emulsions may improve their physical and chemical stability, thereby extending their shelf life.

Transglutaminase crosslinking promotes physical and oxidative stability of filled hydrogel particles based on biopolymer phase separation

In the present study, the effect of transglutaminase (TGase) concentration on the physical and oxidative stabilities of filled hydrogel particles created by biopolymer phase separation was investigated. The results showed that filled hydrogels had relatively smaller particle sizes, higher absolute zeta-potentials, higher interfacial layer thicknesses and lightness values with the increasing of TGase concentration (P < 0.05), as evidenced by the apparent viscosity and viscoelasticity behavior. However, the relatively higher TGase concentration promoted the protein aggregation, which weakens the protection of the surface protein layer, having the negatively impacted the physical stability of filled hydrogels. Microstructural images which obtained via cryo-scanning electron microscopy also verified the above results. In particular, it is noted that filled hydrogels displayed the lowest degrees of lipid and protein oxidation during 10 days of storage (P < 0.05) at TGase concentration of 10 U/g. Prevention against oxidation was attributed mainly to TGase crosslinking of protein molecules on the surface of droplets, which likely provided a denser interface around lipid droplets. Our results indicated that TGase was a favourable agent to crosslink protein on the surface of lipid and improve the physical and oxidative stability of filled hydrogel particles.

One-Step Dynamic Imine Chemistry for Preparation of Chitosan-Stabilized Emulsions Using a Natural Aldehyde: Acid Trigger Mechanism and Regulation and Gastric Delivery

Chitosan is a polysaccharide widely used as a structuring agent in foods and other materials because of its positive charge (amino groups). At present, however, it is difficult to form and stabilize emulsions using chitosan due to its high hydrophilicity. In this study, oil-in-water emulsions were prepared using a one-pot green-chemistry method. The chitosan and aldehyde molecules were in situ interfacially conjugated during homogenization, which promoted the adsorption of chitosan onto the oil droplet surfaces where they created a protective coating. The universality of this method was verified by using chitosan with different molecular weights and four kinds of natural aldehydes [cinnamaldehyde (CA), citral (CT), citronella (CN), and vanillin (VL)]. Chitosan with higher molecular weight facilitated the formation of emulsions. By harnessing the dynamic covalent nature of imine bonds, chitosan emulsions with an imine link display dynamic behavior with acid-catalyzed hydrolysis. The aldehyde structure could control the pH point of trigger for breakdown of emulsions, which was 1.0, 3.0, 4.0, and 4.0 for CA emulsion, CT emulsion, CN emulsion, and VL emulsion, respectively. At pH 6.5, aldehyde helped to decrease the interfacial tension of chitosan to about 10 mN/m, while this value would increase if the pH decreased by adding acid during the measurement. Chemical kinetics studies indicated that the hydrophobicity and conjugation effect of the aldehyde together determined the trigger points and properties of the emulsion. Finally, we used the optimized emulsions to encapsulate and control the release of curcumin. The gastric release behavior of the curcumin depended on aldehyde structure: VL > CN > CT ≈ CA. Hence, a tailor-made trigger release emulsion system can be achieved by rational selection and design of aldehyde structure to control hydrophobicity and conjugation effect of aldehydes.

Food-Grade Nanoemulsions: Preparation, Stability and Application in Encapsulation of Bioactive Compounds

Nanoemulsions have attracted significant attention in food fields and can increase the functionality of the bioactive compounds contained within them. In this paper, the preparation methods, including low-energy and high-energy methods, were first reviewed. Second, the physical and chemical destabilization mechanisms of nanoemulsions, such as gravitational separation (creaming or sedimentation), flocculation, coalescence, Ostwald ripening, lipid oxidation and so on, were reviewed. Then, the impact of different stabilizers, including emulsifiers, weighting agents, texture modifiers (thickening agents and gelling agents), ripening inhibitors, antioxidants and chelating agents, on the physicochemical stability of nanoemulsions were discussed. Finally, the applications of nanoemulsions for the delivery of functional ingredients, including bioactive lipids, essential oil, flavor compounds, vitamins, phenolic compounds and carotenoids, were summarized. This review can provide some reference for the selection of preparation methods and stabilizers that will improve performance in nanoemulsion-based products and expand their usage.

Oral behaviour of emulsions stabilized by mixed monolayer

Controlled flavour release is highly important for the formulation of food emulsions. However, manipulating oral behavior and maintaining the stability of the flavoured emulsion is quite challenging. Hence, this study aims to investigate the effect of emulsion stability and oral behaviour using mixed emulsifier monolayers of different nature for their controlled flavour release. Orange oil flavoured (0.1% orange oil +10% sunflower oil) oil-in-water emulsions were prepared by microfluidization through modified starch (MS) and whey protein isolate (WPI) with different mass ratios (0.5:0.5, 0.5:1, 1:0.5, 1:1, 1:0 and 0:1) of emulsifiers. The fabricated emulsions were <0.13 μm in size (d₃₂) with stable oil droplets having strong negative charges. The 0.5:0.5 and 0:1 emulsion were depicted an increase in size d₃₂ (1.17 and 0.93 μm) and unstable during storage at 28 ± 1 °C than the emulsions stored at 4 ± 0.1 °C. All the emulsions were exhibited Newtonian flow; however once mixed with artificial saliva, the 1:0 emulsion showed shear thinning behaviour. During oral processing, in-vitro and in-vivo exhibited flocculation and coalescence; subsequently, structural deformation was observed with an increase in size (d₃₂) and weak negative charge in 1:0.5 and 1:0 emulsions. Backscattering profile revealed more destabilization for 1:0 and less for 1:0.5 emulsions. Contrarily, other emulsions did not show any changes. Therefore, oral processing of emulsions results suggested that 1:0 had quick destabilization and 1:0.5 changed gradually. Thus, mixed emulsifier monolayer contributed significantly to the behavior of emulsions when interacting with saliva and it can be useful for controlled flavour release.

Development and Characterization of Whey Protein-Based Nano-Delivery Systems: A Review

Various bioactive compounds (BCs) often possess poor stability and bioavailability, which makes it difficult for them to exert their potential health benefits. These limitations can be countered by the use of nano-delivery systems (NDSs), such as nanoparticles and nanoemulsions. NDSs can protect BCs against harsh environments during food processing and digestion, and thereby, could enhance the bioavailability of BCs. Although various NDSs have been successfully produced with both synthetic and natural materials, it is necessary to fulfill safety criteria in the delivery materials for food applications. Food-grade materials for the production of NDSs, such as milk proteins and carbohydrates, have received much attention due to their low toxicity, biodegradability, and biocompatibility. Among these, whey proteins-from whey, a byproduct of cheese manufacturing-have been considered as excellent delivery material because of their high nutritional value and various functional properties, such as binding capability to various compounds, gelation, emulsifying properties, and barrier effects. Since the functional and physicochemical properties of whey protein-based NDSs, including size and surface charge, can be key factors affecting the applications of NDSs in food, the objectives of this review are to discuss how manufacturing variables can modulate the functional and physicochemical properties of NDSs and bioavailability of encapsulated BCs to produce efficient NDSs for various BCs.

Physicochemical and Microstructural Properties of Polymerized Whey Protein Encapsulated 3,3'-Diindolylmethane Nanoparticles

The fat-soluble antioxidant 3,3′-diindolylmethane (DIM), is a natural phytochemical found in Brassica vegetables, such as cabbage, broccoli, and Brussels sprouts. The stability of this compound is a major challenge for its applications. Polymerized whey protein (PWP)-based DIM nanoparticles were prepared at different mass ratios of protein and DIM by mixing PWP and DIM followed by ultrasound treatment for 4 min. All the nanoparticles were studied for particle size, zeta potential, rheological and microstructural properties, and storage stability. The mean particle size of the PWP-based nanoparticles was significantly increased (p < 0.05) by the addition of DIM at different mass ratios, ranging from 241.33 ± 14.82 to 270.57 ± 15.28 nm. Zeta potential values of all nanoparticles were highly negative (greater than ±30 mV), suggesting a stable solution due its electrostatic repulsive forces. All samples exhibited shear thinning behavior (n < 1), fitted with Sisko model (R² > 0.997). Fourier Transform Infrared (FTIR)spectra revealed that the secondary structure was changed and the absorption intensity for hydrogen bonding got stronger by further incorporating DIM into PWP. Transmission electronic microscopy (TEM) images showed spherical and smooth surface shape of the PWP-based nanoparticles. DIM encapsulated by PWP showed enhanced stability at 4, 37 and 55 °C for 15 days evidenced by changes in mean particle size and color (a*-value and b*-value) compared with control (DIM only). In conclusion, the polymerized whey protein based 3,3′-diindolylmethane nanoparticles are stable and the encapsulation may protect the core material from oxidation.

Physicochemical Properties and Storage Stability of Food Protein-Stabilized Nanoemulsions

This study investigated the preparation and properties of corn oil nanoemulsions stabilized by peanut protein isolate (PPI), rice bran protein isolate (RBPI), soybean protein isolate (SPI), and whey protein isolate (WPI). The mean droplet diameter of four protein-stabilized nanoemulsions prepared via ultrasound method was less than 245 nm. PPI-stabilized nanoemulsions showed better stability for 4 weeks, while the mean droplet diameter of RBPI-stabilized nanoemulsions had exceeded 1000 nm during the third week of storage. Fourier transform infrared and interfacial tension (IT) analysis showed that the higher level of disordered structure and lower IT of proteins made the stability of nanoemulsions better. Moreover, bivariate correlation analysis discovered that α-helix (p < 0.01) and β-turn (p < 0.05) of proteins were related to the mean droplet diameter of nanoemulsions, the random coil (p < 0.05) was related to the zeta potential of nanoemulsions. This study provided new idea for the relationship between the structure of protein and properties of protein-stabilized nanoemulsions.