Cold-water solubility, oil-adsorption and enzymolysis properties of amorphous granular starches

Effect of different screw speeds on the structure and properties of starch straws

To illustrate the action mechanism of screw speed on the performance of starch-based straws during the extrusion process, starch-based straws at different screw speeds were prepared using a twin-screw extruder and the structures and characteristics were compared. The results indicated that as screw speeds improved from 3 Hz to 13 Hz, the A chain of amylopectin increased from 25.47 % to 28.87 %, and the B3 chain decreased from 6.34 % to 3.47 %. The absorption peak of hydroxyl group shifted from 3296 cm-1 to 3280 cm-1. The relative crystallinity reduced from 13.49 % to 9.89 % and the gelatinization enthalpy decreased from 3.5 J/g to 0.2 J/g. The performance of starch straws did not increase linearly with increasing screw speeds. The starch straw produced at screw speed of 7 Hz had the largest amylose content, the highest gelatinization temperature, the minimum bending strength, and the lowest water absorption rate in hot water (80 °C). Screw speed had a remarkable impact on the mechanical strength, toughness and hydrophobicity of starch-based straws. This study revealed the mechanism of screw speed on the mechanical strength and water resistance of starch straws in the thermoplastic extrusion process and created the theoretical basis for the industrial production of starch-based straws.

Effects of explosion puffing on the native structural organization and oil adsorption properties of starch

The effects of explosion puffing (EP) on the native structural organization (i.e., thermal properties, crystalline structure, short-range order, granule morphology and powder properties) and oil adsorption properties of puffed starch (PS) were investigated. The results showed that EP treatment could decrease the melting enthalpy of starch double helices and increase the V-type crystallinity. The highest V-type crystallinity (24.7 %) was obtained when the puffing pressure was 0.4 MPa and the starch:ethanol:water ratio was 1:2:1 (w/w). By controlling the puffing conditions, EP treatment can alter the morphology, and increase the particle size, flowability and specific surface area of PS. The high amorphous proportion and porous sheet structure of PS resulted in the highest oil adsorption capacity when the starch:ethanol:water ratio was 1:1:1 (w/w). Pearson correlation analysis showed that oil adsorption capacity was significantly and positively correlated with the 1022/995 cm-1 value and V-type crystallinity, but negatively correlated with bulk density and angle of repose. Furthermore, oil retention capacity was strongly dependent on V-type crystallinity. These findings demonstrated that EP is an innovative technology with the potential to enhance the V-type crystallinity and adsorption performance of starch.

Oil structuring from porous starch to powdered oil: Role of multi-scale structure in the oil adsorption and distribution

Oil structuring from porous starch is a potential alternative for the industrial production of powdered oil, but their relationship between starch multi-scale structure and oil adsorption characteristics was not clear. This study compared the role of multi-scale structure of porous starch (PS) prepared by normal and waxy maize starch in the oil adsorption. Waxy maize porous starch exhibited higher oil adsorption capacity (32.43 %-98.71 %) and more oil distributed on the surface of granules than normal maize porous starch, resulting from the more pores, larger specific surface area (1.01-1.53 m2/g), and pore size (8.45-9.32 nm). The enzymolysis time of native starch dominated oil distribution, leading to different granule adhesion and aggregation state. Pearson correlation analysis further showed oil adsorption capacity was negatively correlated with particle size, but positively correlated with enzymolysis rate and specific surface area of PS. The formation of powdered oil was mainly through the physical adsorption, including surface adsorption and pore adsorption. These findings could provide a promising route for the preparation of powdered oil with controlled multi-scale structure of PS.

Effect of electron beam irradiation on granular cold-water swelling chestnut starch: Improvement of cold-water solubility, multiscale structure, and rheological properties

In this study, granular cold-water swelling (GCWS) starch was prepared from chestnut starch by ethanol-alkali method, after which it was further modified by electron beam irradiation (EBI) technique to investigate the effect of EBI on GCWS chestnut starch. It was shown that the alcohol-alkali treatment disrupted the starch double helix structure and the starch crystalline form had been changed from "C" to "V" type. On this basis, EBI continued to act on the disrupted starch chains and further cleaved the long chains into short chains, which significantly improved the solubility of starch to 90.08 % in cold water at a 24 kGy irradiation dose. Therefore, this study can broaden the application scope of starch and provide new ideas for GCWS starch applications in food and water-soluble pharmaceutical industries.

Pulsed Electric Field-Assisted Enzymatic and Alcoholic-Alkaline Production of Porous Granular Cold-Water-Soluble Starch: A Carrier with Efficient Zeaxanthin-Loading Capacity

In this study, porous starch was modified using pulsed electric field (PEF) pretreatment and alcoholic-alkaline treatment to prepare porous granular cold-water-soluble starch (P-GCWSS). The soluble porous starch has high adsorption capability and high cold water solubility, allowing effective encapsulation of zeaxanthin and improving zeaxanthin's water solubility, stability, and bioavailability. The physical and chemical properties of GCWSS and complex were investigated using scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction. The results showed that the cold water solubility of the pulsed electric field-treated porous granular cold-water-soluble starch (PEF-P-GCWSS) increased by 12.81% compared to granular cold-water-soluble starch (GCWSS). The pulsed electric field treatment also increased the oil absorption of PEF-P-GCWSS was improved by 15.32% compared to porous granular cold-water-soluble starch (P-GCWSS). PEF-P-GCWSS was effective in encapsulating zeaxanthin, which provided a good protection for zeaxanthin. The zeaxanthin-saturated solubility in water of PPG-Z was increased by 56.72% compared with free zeaxanthin. The zeaxanthin embedded in PEF-P-GCWSS was able to be released slowly during gastric digestion and released rapidly during intestinal digestion.

Biochar and Nitrogen Fertilizer Change the Quality of Waxy and Non-Waxy Broomcorn Millet (Panicum miliaceum L.) Starch

The overuse of nitrogen fertilizers has led to environmental pollution, which has prompted the widespread adoption of biochar as a soil conditioner in agricultural production. To date, there has been a lack of research on the effects of biochar and its combination with nitrogen fertilizer on the quality of broomcorn millet (Panicum miliaceum L.) starch. Thus, this study examined the physicochemical characteristics of starch in two types of broomcorn millet (waxy and non-waxy) under four different conditions, including a control group (N0), nitrogen fertilizer treatment alone (N150), biochar treatment alone (N0+B), and a combination of biochar and nitrogen fertilizer treatments (N150+B). The results showed that, in comparison to the control, all the treatments, particularly N150+B, decreased the content of amylose and gelatinization temperature and enhanced the starch transparency gel consistency and swelling power. In addition, biochar can improve the water solubility of starch and the gelatinization enthalpy. Importantly, the combination of biochar and nitrogen fertilizer increased the proportion of A-granules, final viscosity, starch content, and the average degree of amylopectin in polymerization. Thus, this research indicates that the combinations of biochar and nitrogen fertilizer result in the most significant improvement in the quality of starch produced from broomcorn millet.

Unveiling the retrogradation mechanism of a novel high amylose content starch-Pouteria campechiana seed

The research of starch retrogradation have been attracting interest. Thereby, the long-term retrogradation mechanism (0-21 days) of Pouteria campechiana seed starch (PCSS) was investigated. The results showed that crystal type was changed from A- to B + V-type during retrogradation. The retrogradation PCSS (RPCSS) exhibited faster retrogradation rate and more compact internal ultra-structure compared to rice, wheat and maize starch. Pearson correlation indicated that, as retrogradation days increased, values of α-1,4-glycosidic bond, A chains, double helix, V-type polymorphism, Mw, relative crystallinity (Rc) and short-range order gradually significantly increased, and B1 chains, B3 + chains values gradually significantly dropped (p < 0.05). These inferred an increasing peak temperature and compactness of morphology with increasing retrogradation days. Compared to native starch, RPCSS α-1.4-glycosidic bond was increased, which indicated that its quick molecules degradation including decreased Mw, B3 + chains, Rc, semicrystalline order, and ΔH. These might provide a theoretical direction for preparation of starch-basis food.

Effects of different rapid cooling temperatures and annealing on functional properties of starch straws after thermoplastic extrusion

To improve the performance of starch straws in rapidly cooling and annealing procedure of thermoplastic extrusion, control straw was prepared through slowly cooling at 25 °C, and starch straw was prepared through regulating different rapid cooling temperatures including 20 °C, 5 °C, -10 °C and -20 °C. The results indicated that control straw exhibited a homogeneous state, while starch straws treated by rapid cooling displayed like a wash-board structure. Compared to control straw, the ratio of the absorption peak intensity of 1047 and 1022 cm^-1 increased from 1.050 to 1.455 as cooling temperatures decreased from 25 °C to -20 °C, indicating short-range order of the double helix structure significantly enhanced. The relative crystallinities of starch straws increased from 12.01 % to 16.58 %. The maximum bending force value (60.92 N) of starch straws cooled at -20 °C was significantly higher than that (46.14 N) of control straw. Conversely, the modulus of elasticity in bending values (4.21-16.43 N/cm) of rapid cooling-treated straws were significantly lower than that (48.42 N/cm) of control straw. Water absorption of rapid cooling-treated straws were lower than that of control straw, indicating the hydrophobicity property of starch straws significantly improved.

Colorimetric porous microspheres of natural sodium alginate for chilled pork visual monitoring

Chilled meat is subject to deterioration by various factors during storage and distribution. Therefore, it is very important to monitor the quality of meat in real time. This study aims at preparing a natural, low-cost indicating microsphere to visualize the freshness of meat by the combination of sodium alginate (SA) and chitosan with 0-10 wt% anthocyanins derived from chokeberry as a colorant using ionic gelation method. Size-controlled porous SA microspheres with were further constructed by freeze-drying and their physicochemical properties were characterized by SEM, FTIR, DSC, and XRD. Results showed that microspheres with 1 wt% anthocyanin showed good responsiveness to different concentrations of ammonia and were able to effectively identify the freshness of chilled meat by color change. Principal component analysis showed that the color difference of the porous microspheres was highly significantly correlated with pH, TVB-N, total plate count and thiobarbituric acid active substance (p < 0.01), suggesting a visible satisfactory capability of the microspheres to identify the spoilage in pork. Principal component analysis showed that the color difference of the porous microspheres was highly significantly correlated with pH, TVB-N, total plate count and thiobarbituric acid active substance (P < 0.01), suggesting a visible satisfactory capability of the microspheres to identify the spoilage in pork.

pH-shifting alters textural, thermal, and microstructural properties of mung bean starch-flaxseed protein composite gels

The objective of this study was to investigate the effect of pH-shifting on the textural and microstructural properties of mung bean starch (MBS)-flaxseed protein (FP) composite gels. Results showed that different pH-shifting treatments caused changes in hydrogen bond interactions and secondary structures in composite gels, leading to the formation of loose or compact gel networks. The pH 2-shifting modified protein and starch molecules with shorter chains tended to form smaller intermolecular aggregates, resulting in the formation of a looser gel network. For pH 12-shifting treatment, conformational change of FP caused the unfolding of protein and the exposure of more hydrophobic groups, which enhanced the hydrogen bond and hydrophobic interactions between polymers, contributing to the formation of a compact gel network. Furthermore, pH 12-shifting improved the water-holding capacity (WHC), storage modulus, and strength of gels, while pH 2-treated gels exhibited lower WHC, hardness, and gumminess due to the degradation of MBS and denaturation of FP caused by extreme acid condition. These findings suggest that pH-shifting can alter the gel properties of bi-polymeric starch-protein composite systems by affecting the secondary structures of proteins and the hydrogen bonding between the polymers, and provide a promising way for a wide application of FP in soft gel-type food production.

Textural characterization of calcium salts-induced mung bean starch-flaxseed protein composite gels as dysphagia food

Effects of calcium gluconate (CG), calcium lactate (CL) and calcium dihydrogen phosphate (CDP) on the structural and functional properties of mung bean starch (MBS)-flaxseed protein (FP) composite gels were investigated to explore the feasibility of developing dysphagia food. The water-immobilizing, rheological and structural properties of MBS-FP composite gels adding different calcium salts (10, 30, and 50 mmol/L) were analyzed by low-field nuclear magnetic resonance measurement, rheological and textural analyses, fourier transform infrared spectroscopy, scanning electron microscopy and confocal laser scanning microscopy. Results showed that calcium salts imparted various soft gel properties to the composite gels by influencing the interactions between MBS and FP. Calcium salts could affect the conformation of amylose chains, accelerate the aggregation of FP molecules, and increase the cross-linking between starch and protein aggregates, resulting in the formation of large aggregates and a weak gel network. Consequently, calcium salts-induced composite gels showed lower viscoelastic moduli and gel strength than the control gel. In particular, different calcium salts had various impacts on the gel properties due to their diverse ability forming hydrogen bonds. Compared with CL and CDP, the gels containing CG presented the higher viscoelastic moduli and hardness, and possessed an irregular cellular network with the increased pore number and the decreased wall thickness. The gel containing 50 mmol/L CL had the highest water-holding capacity, in all the gels tested, by retaining more immobilized and mobile water in the compact gel network with larger cavities. The gels adding CDP presented lower hardness and gumminess due to the obvious lamellar structure within the network. International dysphagia diet standardization initiative (IDDSI) tests indicated that the gels adding CG and CL could be categorized into level 6 (soft and bite-sized) dysphagia diet, while the samples adding CDP could be classified into level 5 (minced and moist). These findings provide insights for the development of the novel soft gel-type dysphagia food.

Study on structural characteristics, physicochemical properties, and in vitro digestibility of Kudzu-resistant starch prepared by different methods

Three different methods, including autoclaving, autoclaving-debranching, and purification, were used to prepare Kudzu-resistant starch (KRS) from Kudzu starch (KS). The physicochemical properties, such as thermodynamic properties, pasting properties, solubility, swelling, and coagulability, as well as the in vitro digestive characteristics of the three kinds of KRS were studied. The results showed that the morphology of starch granules of KRS prepared by autoclave, autoclave enzymatic hydrolysis, and purification methods was changed and the relative crystallinity was significantly decreased compared with the original starch. X-ray diffraction (XRD) showed that KRS exists in the form of C and C+V crystalline form. There was a significant increase in the pasting temperature and a remarkable decrease in the peak viscosity and the expansion degree of the KRS prepared by all three methods. The solubility of the resistant starch (RS) obtained by autoclaving-debranching and that by purification were both increased compared to that of native KS, while the solubility of the RS obtained by autoclaving was decreased. Meanwhile, the retrogradation of the three RS was also improved to varying degrees. The contents of RS in the samples were: P-KRS (71%) > DA-KRS (43%) > A-KRS (42%) > KS (9%). Simulated human in vitro digestion experiments showed that RS has stronger antidigestibility properties than native starch. Among them, the RS prepared by the purification method has stronger antidigestive properties, and it is predicted that it may have a better potential value in regulating blood glucose. These results indicated that the processing properties of KRS, especially the digestibility, are significantly improved and can be used as a new functional food ingredient, which deserves thorough study.

Dual Modification of Sago Starch via Heat Moisture Treatment and Octenyl Succinylation to Improve Starch Hydrophobicity

To elucidate the pretreatment of a heat moisture treatment that could increase the DS and hydrophobicity of OSA starch, the effect of the moisture level of the HMT process on the physicochemical properties was investigated. The higher moisture content (MC) in the HMT process led to a decreasing degree of crystallinity and gelatinization enthalpy and also produced surface damage and cracking of the granules. HMT pretreatment with the right moisture content resulted in OSA starch with the maximum DS value and reaction efficiency. Pre-treatment HMT at 25% MC (HMT-25) followed by OSA esterification exhibited the highest DS value (0.0086) and reaction efficiency (35.86%). H25-OSA starch has been shown to have good water resistance (OAC 1.03%, WVP 4.92 × 10⁻⁵ g/s m Pa, water contact angle 88.43°), and conversely, has a high cold water solubility (8.44%). Based on FTIR, there were two new peaks at 1729 and 1568 cm⁻¹ of the HMT-OSA starch, which proved that the hydroxyl group of the HMT starch molecule had been substituted with the carbonyl and carboxyl ester groups of OSA.