Single stage batch adsorber design for efficient Eosin yellow removal by polyaniline coated ligno-cellulose

organo acid-activated clays for water treatment as removal agent of Eosin-Y: Properties, regeneration, and single batch design absorber

Organoclays have been proposed as efficient removal agents for colored wastewater treatment. In this study, organo-acid-activated clays were investigated for their ability to remove eosin Y dye molecules. Firstly, the clay was acid activated using sulfuric solution at 90 °C for overnight. Secondly, the resulting materials were treated by hexadecyltetramethylammonium bromide solutions to obtain organo-acid-activated clays. Several techniques were used, such as X-ray diffraction, carbon hydrogen nitrogen analysis, silicon-29 and carbon-13 solid-state nuclear magnetic resonance, and nitrogen adsorption isotherms. The cation exchange capacity values were reduced and the specific surface area values increased from 80.1 m2/g to 183.2 m2/g during the acid activation process. The resulting organo-acid-activated clays had a similar expansion of interlayer spacing of 3.90 nm with less intercalated hexadecyltetramethylammonium surfactants, ranging from 0.80 mmol/g to 1.22 mmol/g; 13C solid NMR indicated that the intercalated surfactants exhibited different degree of conformation. Many factors, including the solid dose, solution pH, amount of intercalated surfactants, and starting eosin-Y concentrations, were studied in relation to the removal capabilities of organo acid-activated clays. Based on the Langmuir model, the removal capacity of the organo acid-activated clays ranged from a minimum of 43.5 mg/g to a maximum of 79.3 mg/g, dependent on the surfactant quantities and acid activation degree. , and the pH. The removal percentage of eosin-Y was increased from 50.5 % to 80.8 % by treating the organo acid-activated clay with HCl solution before the removal procedure. Regeneration and reuse of two selected organo acid-activated clays were carried out for seven successive cycles, and a reduction in the initial efficiency was in the range of 26.4 %-30.1 %. However, for organoclay (without acid activation), approximately 52.1 % efficiency was maintained. Using the Langmuir model and mass balance equations, a single-stage adsorber design was suggested for different dye volumes at a constant starting concentration.

Mechanistic insights into carbo-catalyzed persulfate treatment for simultaneous degradation of cationic and anionic dye in multicomponent mixture using plastic waste-derived carbon

Upcycling waste into value-added products for utilization in wastewater abatements has been explored in a number of treatment technologies. One such waste, single-use plastic, which poses significant adverse environmental and economic impact, has been chosen and converted into graphitic carbon to reduce the waste burden sustainably and economically. The sorptive and catalytic performance of synthesized plastic waste-derived carbon (PWC) was evaluated using brilliant green (BG) and eosin yellow (EY) as target pollutants. The adsorption capacity of PWC was very low for BG (7.41 mg/g) and EY (4.93 mg/g). The coupling of PWC with peroxymonosulfate (PMS) promoted dye degradation. Complete degradation of the dye, with ~61% reduction in TOC and ~95% reduction in toxicity, was achieved by oxidative treatment (initial concentration: 10 mg/L). The functionalities of PWC facilitated better electron transfer to PMS for its effective activation, which led to the production of SO₄^•- and OH^•. The quenching study confirmed that the degradation of dyes was primarily due to SO₄^•-. Additionally, the pathways of dye degradation were proposed based on the intermediates identified. Thus, this study established the high potential of PWC as a metal-free catalyst in PMS activation for the abatement of organic pollutants.

Removal of Chromium (VI) by a Magnetic Nanoscale Zerovalent Iron-Assisted Chicken Manure-Derived Biochar: Adsorption Behavior and Synergetic Mechanism

Using chicken manure as raw material to prepare activated carbon as a dispersant, a novel biochar-loaded nano-zerovalent iron composite (nZVI@CMBC) was developed and applied to remove hexavalent chromium, i.e., Cr(VI), in wastewater. The dispersion of nano-zerovalent iron (nZVI) particles on the surface of chicken manure–derived biochar (CMBC) successfully inhibited the aggregation of magnetic iron particles and effectively reduced the size of nZVI particles. The results demonstrated that under acidic conditions, the removal efficiency of Cr(VI) by the nZVI@CMBC composite could reach 124.12 mg g⁻¹. The pseudosecond-order kinetic model had a good agreement with the adsorption kinetics of the nZVI@CMBC composite, implying that the adsorption of Cr(VI) is based on the multi-layer chemical adsorption. Therefore, this study provides a new clue and strategy for removing Cr(VI) in wastewater.

Highly efficient adsorption and mechanism of alkylphenols on magnetic reduced graphene oxide

The influence of alkylphenols to environment cannot be ignored, as they are common product from chemical industries and potential threat to human health. Some alkylphenols are listed as persistent toxic substances (PTS) by the United Nations Environment Programme (UNEP). In this study, the optimized magnetic reduced graphene oxide (MrGO) was synthesized by a facile solvothermal method, and investigated for adsorption of three typical alkylphenols. In neutral condition, MrGO showed extremely high adsorption capacity of three typical alkylphenols, 4-heptylphenol (4-HP), 4-tert-octylphenol (4-OP), and 4-nonylphenol (4-NP), which could reach 938.9 mg g^-1 (40 °C), 987.8 mg g^-1 (40 °C), and 989.7 mg g^-1 (20 °C), respectively. This study revealed that the adsorption process was a heterogeneous multi-layer physical adsorption, and the adsorption rates were related to the number of unoccupied vacancies on the adsorbent surface. From batch experiments and density functional theory (DFT) calculations, the main adsorption interactions between MrGO and alkylphenols were deduced to be π-π, hydrogen-bond, and hydrophobic interactions. What's more, the different affinities of MrGO towards different targets were further distinguished and explained in detail. The wonderful stability and recyclability of MrGO made it a promising cost-effective remediation candidate.

Biochar-supported polyaniline hybrid for aqueous chromium and nitrate adsorption

Biochar adsorbents can remove environmental pollutants and the remediation of Cr(VI) and nitrate are considered. Cr(VI) is a proven carcinogen causing serious health issues in humans and nitrate induced eutrophication causes negative effect on aquatic systems around the world. Douglas fir biochar (DFBC), synthesized by fast pyrolysis during syn gas production, was treated with aniline. Then, a polyaniline biochar (PANIBC) composite containing 47 wt% PANI was prepared by precipitating PANI on DFBC surfaces by oxidative chemical polymerization of aniline in 2M HCl. PANIBC exhibited a point of zero charge (PZC) of 3.0 and 8.2 m²/g BET (N₂) surface area. This modified biochar was characterized by thermogravimetric analysis (TGA), scanning electron microscopy (SEM) morphology and surface elements, and oxidation states by X-ray photoelectron spectroscopy (XPS). PANIBC exhibited positive surface charge below pH 3, making it an outstanding adsorbent, for Cr(VI) removal. Cr(VI) and nitrate removal mechanisms are presented based on XPS analysis. DFBC and PANIBC Cr(VI) and nitrate adsorption data were fitted to Langmuir and Freundlich isotherm models with maximum Langmuir adsorption capacities of 150 mg/g and 72 mg/g, respectively. Cr(VI) and nitrate removal at pH 2 and 6 were evaluated by reducing the amount of PANI (9 wt%) dispersed on to DFBC. Adsorption capacities verses temperature studies revealed that both Cr(VI) and nitrate adsorption are endothermic and thermodynamically favored. Regeneration studies were conducted on both DFBC and PANIBC using 0.1M NaOH and PANIBC exhibited excellent sorption capacities for Cr(VI) and nitrate in lake water samples and in the presence of competitive ions.

Monodisperse amino-modified nanosized zero-valent iron for selective and recyclable removal of TNT: Synthesis, characterization, and removal mechanism

Nitroaromatic explosives are major pollutants produced during wars that cause serious environmental and health problems. The removal of a typical nitroaromatic explosive, 2,4,6-trinitrotoluene (TNT), from aqueous solution, was conducted using a new recyclable magnetic nano-adsorbent (Fe@SiO₂NH₂). This adsorbent was prepared by grafting amino groups onto Fe@SiO₂ particles with a well-defined core-shell structure and demonstrated monodispersity in solution. The removal performance of the nano-adsorbent towards TNT was found to be 2.57 and 4.92 times higher than that towards two analogous explosives, 2,4-dinitrotoluene (2,4-DNT) and 2-nitrotoluene (2-NT), respectively, under neutral conditions. The difference in the removal performance among the three compounds was further compared in terms of the effects of different conditions (pH value, ionic strength, humic acid concentration, adsorbent modification degree and dosage, etc.) and the electrostatic potential distributions of the three compounds. The most significant elevation is owing to modification of amino on Fe@SiO₂ which made a 20.7% increase in adsorption efficiency of TNT. The experimental data were well fit by the pseudo-second-order kinetic model and the Freundlich adsorption isotherm model, indicating multilayer adsorption on a heterogeneous surface. The experimental results and theoretical considerations show that the interactions between Fe@SiO₂NH₂ NPs and TNT correspond to dipole-dipole and hydrophobic interactions. These interactions should be considered in the design of an adsorbent. Furthermore, the adaptability to aqueous environment and excellent regeneration capacity of Fe@SiO₂NH₂ NPs makes these remediation materials promising for applications.

Enhanced electrical and thermal properties of semi-conductive PANI-CNCs with surface modified CNCs

Cellulose nanocrystals (CNCs) are the most commonly used natural polymers for biomaterial synthesis. However, their low dispersibility, conductivity, and poor compatibility with the hydrophobic matrix hinder their potential applications. Therefore, we grafted sulfate half-ester and carboxylic functional groups onto CNC surfaces (S-CNC and C-CNC) to overcome these shortcomings. The effect of the dopants, surfactant ratios, and properties of CNCs on the thermal stability, conductivity, and surface morphology of polyaniline (PANI)-doped CNC nanocomposites were investigated through emulsion and in situ polymerization. The higher electrical conductivity and well-dispersed morphology of SCNC-PANI₃₀ (1.1 × 10^-2 S cm^-1) but lower thermal stability than that of CCNC-PANI₃₀ (T ₀: 189 °C) nanocomposites are highly related to dispersibility of S-CNCs. However, after 4-dodecylbenzenesulfonic acid (DBSA) was added, the conductivity and thermal stability of SCNC/PANI increased up to 2.5 × 10^-1 S cm^-1 and 192 °C with almost no particle aggregation because of the increase in charge dispersion. The proposed biodegradable, renewable, and surface-modified S-CNC and C-CNC can be used in high-thermal-stability applications such as food packaging, optical films, reinforcement fillers, flexible semiconductors, and electromagnetic materials.

Investigation of nanoscale zerovalent iron-based magnetic and thermal dual-responsive composite materials for the removal and detection of phenols

In this study, well-defined magnetic and thermal dual-responsive nanomaterials were synthesized, which contained ultrafine core-shell Fe@SiO₂ nanoparticles as magnetic core and poly(N-isopropylacrylamide) (PNIPAM) as thermosensitive outer shell. The fabricated nanoparticles were characterized and investigated for the adsorption of four phenolic compounds, including bisphenol A (BPA), tetrabromobisphenol A (TBBPA), 4-tert-octylphenol (4-OP) and 4-n-nonylphenol (4-NP). The experimental results demonstrated that the excellent adsorption rates were attributed to hydrophobic effect, hydrogen-bonding interaction, and electrostatic attraction. The adsorption process followed pseudo-second-order kinetics model and nonlinear isotherms, indicating heterogeneous adsorption process. The adsorption efficiency of 4-NP using Fe@SiO₂@PNIPAM was more than 90% under optimized condition within 2 h. The determined maximum adsorption amounts of BPA, TBBPA, 4-OP and 4-NP were 2.43, 6.83, 24.75, and 49.34 mg g^-1, respectively. Meanwhile, a magnetic solid phase extraction (MSPE) method with Fe@SiO₂@PNIPAM was established to determine these four compounds simultaneously. Under the optimal conditions, the linearity ranges were in the range of 2-200, 2-300, 2-100 and 2-100 μg L^-1 for BPA, 4-OP, TBBPA, and 4-NP, respectively, and the detection limits were in the range of 0.58-0.76 μg L^-1, respectively. The applicability of the proposed method was evaluated by analyzing three fresh water samples, and satisfactory spiked recoveries in the range 70.9-119.9% were achieved. It was proved that these adsorbents could be easily collected and recycled owing to the appropriate magnetism. The results also demonstrated that the as-prepared adsorbents had promising potential in the enrichment and analysis of detrimental organic pollutants from water.

Iron-based magnetic molecular imprinted polymers and their application in removal and determination of di-n-pentyl phthalate in aqueous media

Iron-based magnetic molecular imprinted polymers (Fe@SiO₂@MIP) were synthesized for highly selective removal and recognition of di-n-pentyl phthalate (DnPP) from water. Well-defined core-shell Fe@SiO₂ nanoparticles (less than 70 nm) were decorated on MIPs reticular layers to endow DnPP-MIPs with magnetic property for the first time. Five other phthalic acid esters including dimethyl phthalate, diethyl phthalate, dipropyl phthalate, di-n-butyl phthalate and di-iso-octyl phthalate were used to investigate the adsorptive selectivity to DnPP. The designed experiments were carried out to explore the adsorption kinetics, isotherms and thermodynamics and the results demonstrated that the adsorption was a spontaneous, exothermal and physical adsorption process. The materials were proved to be excellent adsorbents in removal of DnPP with an adsorption capacity as high as 194.15 mg g^-1 in optimal condition. Furthermore, a magnetic solid phase extraction with Fe@SiO₂@MIP coupled to high-performance liquid chromatography method was successfully developed for the determination of DnPP, and the proposed method achieved a good linear range of 0.5-250 µg l^-1 with a correlation coefficient (R²) of 0.999 and low limit of detection (LOD) of 0.31 µg l^-1. These materials exhibited excellent capacity in removal and highly sensitive identification of DnPP from aqueous environment samples, and opened a valuable direction for developing new adsorbents for the removal and enrichment of important pollutants.

Recyclable nanoscale zero-valent iron-based magnetic polydopamine coated nanomaterials for the adsorption and removal of phenanthrene and anthracene

In this study, nanoscale zero-valent iron nanoparticles (NZVIs) were coated with silica and polydopamine using a two-step process. The coated nanoparticles were applied as adsorbents for removal of two common polycyclic aromatic hydrocarbons pollutants, phenanthrene (PHE) and anthracene (ANT) from aqueous system. Adsorption kinetics followed a pseudo-second-order model. Isotherms and thermodynamics were investigated and the results indicated that the adsorption process fit best to the Freundlich model and exhibited the characteristics of an exothermal physical adsorption process. Owing to their superparamagnetic characteristics and stability, these adsorbents could be easily collected and recycled for reuse.