Isolation and characterization of nanocrystalline cellulose from roselle-derived microcrystalline cellulose

Preparation and characterization of microcrystalline cellulose from rice bran

BACKGROUND

Rice bran, a by-product of rice processing, has not been fully utilized except for the small amount used for raising animals. The raw material source requirements of microcrystalline cellulose are becoming increasingly extensive. However, the characteristics of preparing microcrystalline cellulose from rice bran have not been reported, which limits the application of rice bran.

RESULTS

Microcrystalline cellulose was obtained from rice bran by alkali treatment, delignification, bleaching and acid hydrolysis. The morphology, particle size distribution, degree of polymerization, crystallinity, and thermal stability of rice bran microcrystalline cellulose were analyzed. The chemical compositions, scanning electron microscopy and Fourier-transform infrared analysis for rice bran microcrystalline cellulose showed that the lignin and hemicellulose were successfully removed from the rice bran fiber matrix. The morphology of rice bran microcrystalline cellulose was shown to be of a short rod-shaped porous structure with an average diameter of 65.3 μm. The polymerization degree of rice bran microcrystalline cellulose was 150. The X-ray diffraction pattern of rice bran microcrystalline cellulose showed the characteristic peak of natural cellulose (type I), and its crystallization index was 71%. The rice bran microcrystalline cellulose may be used in biological composites with temperatures between 150 °C and 250 °C.

CONCLUSION

These results suggest the feasibility of using rice bran as a low-price source of microcrystalline cellulose. © 2024 Society of Chemical Industry.

Eco-Friendly Lithium Separators: A Frontier Exploration of Cellulose-Based Materials

Lithium-ion batteries, as an excellent energy storage solution, require continuous innovation in component design to enhance safety and performance. In this review, we delve into the field of eco-friendly lithium-ion battery separators, focusing on the potential of cellulose-based materials as sustainable alternatives to traditional polyolefin separators. Our analysis shows that cellulose materials, with their inherent degradability and renewability, can provide exceptional thermal stability, electrolyte absorption capability, and economic feasibility. We systematically classify and analyze the latest advancements in cellulose-based battery separators, highlighting the critical role of their superior hydrophilicity and mechanical strength in improving ion transport efficiency and reducing internal short circuits. The novelty of this review lies in the comprehensive evaluation of synthesis methods and cost-effectiveness of cellulose-based separators, addressing significant knowledge gaps in the existing literature. We explore production processes and their scalability in detail, and propose innovative modification strategies such as chemical functionalization and nanocomposite integration to significantly enhance separator performance metrics. Our forward-looking discussion predicts the development trajectory of cellulose-based separators, identifying key areas for future research to overcome current challenges and accelerate the commercialization of these green technologies. Looking ahead, cellulose-based separators not only have the potential to meet but also to exceed the benchmarks set by traditional materials, providing compelling solutions for the next generation of lithium-ion batteries.

Unveiling structure and performance of tea-derived cellulose nanocrystals

In this study, cellulose was extracted from black tea residues to produce black tea cellulose nanocrystals (BT-CNCs) using an optimized acid hydrolysis method. The structure and performance of BT-CNCs were evaluated. The results showed that the optimal conditions for acidolysis of BT-CNCs included a sulfuric acid concentration of 64 %, a solid-liquid ratio of 1:18 (w/v), a hydrolysis temperature of 45 °C, and a hydrolysis time of 50 min. The optimization process resulted in a 44.8 % increase in the yield of BT-CNCs, which exhibited a crystallinity of 68.57 % and were characterized by the typical cellulose I structure. The diameters of the particles range from 5 to 45 nm, and they exhibit aggregation behavior. Notably, BT-CNCs demonstrated excellent storage stability, and the Tyndall effect occurred when exposed to a single beam of light. Although the thermal stability of BT-CNCs decreased, their primary thermal degradation temperature remained above 200 °C. The colloidal nature of BT-CNCs was identified as a non-Newtonian fluid with "shear thinning" behavior. This study introduces a novel method to convert tea waste into BT-CNCs, increasing the yield of BT-CNCs and enhancing waste utilization. BT-CNCs hold promise for application in reinforced composites, offering substantial industrial value.

New Excipient For Oral Drug Delivery: CNC Derived From Sugarcane Bagasse-Derived Microcrystalline Cellulose

Nanocrystalline cellulose (CNC) has emerged as a subject of researcher's interest because of its diverse attributes encompassing biocompatibility, sustainability, a high aspect ratio, and an abundance of -OH groups suitable for modifications. Sugarcane bagasse microcrystalline cellulose (SCBMCC) was used as the raw material for the preparation of CNC due to its pure cellulose content, which is mildly compromised by the pectin, hemicellulose, lignin, and other lignocellulosic components. In the present work, CNC was extracted from SCBMCC and used as a disintegrant. The classic hydrolysis technique was used for the preparation of CNC. Hydrolytic conditions were optimized using the response surface methodology (RSM). The optimized batch of CNC was characterized using techniques such as field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy. Notably, CNC prepared under a hydrolysis time of 90 min exhibited the highest crystallinity of 69.9%. The average particle size and zeta potential were found to be 145 nm and -34.4 mV, respectively. Thermal analysis suggested that an intermediate hydrolysis time resulted in CNC with enhanced thermal stability, showcasing its potential for pharmaceutical applications. Diclofenac potassium was used as the model drug to evaluate the disintegrant properties of CNC as an excipient. Tablets were prepared using the direct compression method. SCBMCC and CNC were used as disintegrants and were compared with the commercial product. The disintegration times (DTs) attained for the tablets prepared using CNC and SCBMCC are 219 and 339.83 s, respectively. The dissolution study of CNC showed a dissolution efficacy (DE%) of 66 and a mean dissolution time (MDT) of 12. The research findings showed that tablets prepared using CNC as disintegrants exhibited the fastest disintegration compared to other formulations.

Cellulose nanocrystals from celery stalk as quercetin scaffolds: A novel perspective of human holo-transferrin adsorption and digestion behaviours

In this study, cellulose nanocrystals (CNCs) were synthesized from celery stalks to be used as the platform for quercetin delivery. Additionally, CNCs and CNCs-quercetin were characterized using the results of scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and zeta potential, while their interactions with human holo-transferrin (HTF) were also investigated. We examined their interaction under physiological conditions through the exertion of fluorescence, resonance light scattering, synchronized fluorescence spectroscopy, circular dichroism, three-dimensional fluorescence spectroscopy, and fluorescence resonance energy transfer techniques. The data from SEM and TEM exhibited the spherical shape of CNCs and CNCs-quercetin and also, a decrease was detected in the size of quercetin-loaded CNCs from 676 to 473 nm that indicated the intensified water solubility of quercetin. The success of cellulose acid hydrolysis was confirmed based on the XRD results. Apparently, the crystalline index of CNCs-quercetin was reduced by the interaction of CNCs with quercetin, which also resulted in the appearance of functional groups, as shown by FTIR. The interaction of CNCs-quercetin with HTF was also demonstrated by the induced quenching in the intensity of HTF fluorescence emission and Stern-Volmer data represent the occurrence of static quenching. Overall, the effectiveness of CNCs as quercetin vehicles suggests its potential suitability for dietary supplements and pharmaceutical products.

Preparation of cellulose nanocrystal (CNCs) reinforced polylactic acid (PLA) bionanocomposites filaments using biobased additives for 3D printing applications

This work presents the experimental steps taken towards the preparation of 3D printable bionanocomposites using polylactic acid (PLA) biopolymer containing 0.1, 0.5 and 1 wt% CNCs. Optimized amounts of bio-based additives were added to improve the processability and flexibility of the bionanocomposites. The 3D printable bionanocomposite filaments were drawn using a single screw extruder. The bionanocomposites filament was used to 3D print prototypes and test specimens for dynamic mechanical analysis (DMA). Characterization of the CNCs and bionanocomposites was performed using Fourier Transform Infrared Spectroscopy (FTIR) analysis, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The nucleating effect of CNCs enhanced the crystallization behaviour of bionanocomposites by 5%, 15% and 11%, for the different CNCs loadings. The TGA analysis revealed a ∼20 °C improvement in the thermal stability of the bionanocomposites. Meanwhile, the tensile analysis showed a ≥48% increase in the tensile strength of the bionanocomposites filaments which was attributed to the reinforcing effects of CNC. The addition of CNCs significantly increased the melt viscosity, storage and loss modulus of PLA. In summary, the bionanocomposite filaments produced in this study exhibited excellent processibility and superior mechanical and thermal properties.

Synthesis of cellulosic and nano-cellulosic aerogel from lignocellulosic materials for diverse sustainable applications: a review

Cellulosic aerogels are sustainable, biodegradable, and ultra-light porous materials with three-dimensional networks having high specific surface area. Depending on the source of precursor materials, they are categorized into plant-based aerogel, bacterial cellulosic aerogel. Different types of aerogels are also produced from microcrystalline cellulose (MCC), nanocrystalline cellulose (NCC), cellulose microfibril (CMF) and cellulose nanofibril (CNF). Furthermore, inorganic and organic substances are embedded to produce hybrid aerogel or composite aerogel for the enhancement of its performance in various fields. Mixing, gelation, solvent exchange, and drying (e.g., super critical carbon dioxide or freeze drying) are the basic steps involved in cellulosic aerogel synthesis. Based on the composition of precursors during aerogel synthesis, cellulosic aerogels have broad applications in various fields such as adsorbents, electrodes, sensors, captive deionization materials, catalysts, drug delivery, thermal and sound insulating materials. This review provided consolidated information on: (i) classification of cellulosic aerogels based on the sources of raw materials, (ii) processes involved to produce the cellulosic aerogel, (iii) cellulosic aerogel synthesized from MCC, NCC, CMF and CNF, (iv) nano particle doped cellulosic aerogel, and (v) its application in various field with future perspectives.

Self-assembly of porous cellulose fibers and the incorporation of graphene carbon quantum dots for stable luminescence

Porous fibers as excellent carriers can be used to prepare photoluminescence materials. Herein, cellulose nanocrystals (CNCs) were derived from microcrystalline cellulose (MCC) by sulfuric acid hydrolysis. After CNCs were squeezed into a coagulating bath containing silicon precursors obtained by the hydrolysis of tetraethyl orthosilicate, porous cellulose fibers were constructed through self-assembly and then incorporated with graphene carbon quantum dots (GQDs) to prepare porous photoluminescence cellulose fibers. The silicon precursor amount, self-assembly time, and corrosion time were optimized. In addition, the morphology, structure and optical properties of the products were investigated. These results showed that as-prepared porous cellulose fibers with mesopores presented loose and porous mesh. Interestingly, the porous photoluminescence cellulose fibers exhibited blue fluorescence, and the maximum emission peak appeared at 430 nm under the excitation wavelength of 350 nm. Furthermore, the relative fluorescence intensity of the porous photoluminescence cellulose fibers was significantly enhanced compared with nonporous photoluminescence cellulose fibers. This work provided a new method to prepare environmentally and stably photoluminescence fibers, which had potential applications in anti-counterfeit packaging and smart packaging.

Reinforcement of Acrylamide Hydrogels with Cellulose Nanocrystals Using Gamma Radiation for Antibiotic Drug Delivery

In this paper, we report the synthesis of acrylamide hydrogels (net-AAm) reinforced with cellulose nanocrystals (CNCs) using gamma radiation, a powerful tool to obtain crosslinked polymers without the use of chemical initiators and crosslinking agents. Some slight changes in the chemical structure and crystallinity of CNCs took place during gamma irradiation without affecting the nanofiller function. In fact, cellulose nanocrystals had a notable influence over the swelling and mechanical properties on the reinforced hydrogels (net-AAm/CNC), obtaining more rigid material since the Young compression modulus increased from 11 kPa for unreinforced net-AAm to 30 kPa for net-AAm/CNC (4% w/w). Moreover, the studies of retention and release of ciprofloxacin (Cx), a quinolone antibiotic drug, showed that reinforced hydrogels were able to load large amounts of ciprofloxacin (1.2-2.8 mg g-1) but they distributed 100% of the drug very quickly (<100 min). Despite this, they exhibited better mechanical properties than the control sample, allowing their handling, and could be used as wound dressings of first response because they can absorb the exudate and at the same time deliver an antibiotic drug directly over the injury.

Coffee Silverskin Cellulose-Based Composite Film with Natural Pigments for Food Packaging: Physicochemical and Sensory Abilities

To promote a circular economy, the use of agricultural by-products as food packaging material has steadily increased. However, designing food packaging films that meet consumers' preferences and requirements is still a challenge. In this work, cellulose extracted from coffee silverskin (a by-product of coffee roasting) and chitosan were combined with different natural pigments (curcumin, phycocyanin, and lycopene) to generate a variety of composite films with different colors for food packaging. The physicochemical and sensory properties of the films were evaluated. The cellulose/chitosan film showed favorable mechanical properties and water sensitivity. Addition of natural pigments resulted in different film colors, and significantly affected the optical properties and improved the UV-barrier, swelling degree, and water vapor permeability (WVP), but there were also slight decreases in the mechanical properties. The various colored films can influence the perceived features and evoke different emotions from consumers, resulting in films receiving different attraction and liking scores. This work provides a comprehensive evaluation strategy for coffee silverskin cellulose-based composite films with incorporated pigments, and a new perspective on the consideration of the hedonic ratings of consumers regarding bio-based films when designing food packaging.

Effect of Acetylation of Two Cellulose Nanocrystal Polymorphs on Processibility and Physical Properties of Polylactide/Cellulose Nanocrystal Composite Film

Polylactide (PLA) has become a popular alternative for petroleum-based plastics to reduce environmental pollution. The broader application of PLA is hampered by its brittle nature and incompatibility with the reinforcement phase. The aim of our work was to improve the ductility and compatibility of PLA composite film and investigate the mechanism by which nanocellulose enhances PLA polymer. Here, we present a robust PLA/nanocellulose hybrid film. Two different allomorphic cellulose nanocrystals (CNC-I and CNC-III) and their acetylated products (ACNC-I and ACNC-III) were used to realize better compatibility and mechanical performance in a hydrophobic PLA matrix. The tensile stress of the composite films with 3% ACNC-I and ACNC-III increased by 41.55% and 27.22% compared to pure PLA film, respectively. Compared to the CNC-I or CNC-III enhanced PLA composite films, the tensile stress of the films increased by 45.05% with 1% ACNC-I and 56.15% with 1% ACNC-III. In addition, PLA composite films with ACNCs showed better ductility and compatibility because the composite fracture gradually transitioned to a ductile fracture during the stretching process. As a result, ACNC-I and ACNC-III were found to be excellent reinforcing agents for the enhancement of the properties of polylactide composite film, and the replacement some petrochemical plastics with PLA composites would be very promising in actual life.

Complexation between rice starch and cellulose nanocrystal from black tea residues: Gelatinization properties and digestibility in vitro

In this work, cellulose nanocrystal (CNC) was extracted from black tea waste and its effects on the physicochemical properties of rice starch were explored. It was revealed that CNC improved the viscosity of starch during pasting and inhibited its short-term retrogradation. The addition of CNC changed the gelatinization enthalpy and improved the shear resistance, viscoelasticity, and short-range ordering of starch paste, which meant that CNC made the starch paste system more stable. The interaction of CNC with starch was analyzed using quantum chemistry methods, and it was demonstrated that the hydrogen bonds were formed between starch molecules and the hydroxyl groups of CNC. In addition, the digestibility of starch gels containing CNC was significantly decreased because CNC could dissociate and act as an inhibitor of amylase. This study further expanded the understanding of the interactions between CNC and starch during processing, which could provide a reference for the application of CNC in starch-based foods and the development of functional foods with a low glycemic index.

Impact of interactions between peanut protein isolate and cellulose nanocrystals on the properties of Pickering emulsions: Rheological properties and physical stabilities

The interactions between cellulose nanocrystals and proteins can regulate the interfacial properties of Pickering emulsions, which plays a leading role in the stabilities of Pickering emulsions. In this work, oil-in-water (O/W) Pickering emulsions with different oil-water ratios were prepared using peanut protein isolate modified by cellulose nanocrystals (PPI/CL-CNCs). The distributions of PPI/CL-CNCs at the oil-water interfaces and the microstructures of Pickering emulsions were observed by CLSM and cryo-SEM. The results showed that stable complexes PPI/CL-CNCs formed thick and dense interface layers on the surface of oil droplets. The results of rheological tests clarified that the Pickering emulsions showed an elastic and gel texture, and their gel strength could be enhanced by regulating the oil-water ratios from 3:7 to 7:3. In addition, after one month of storage, the EI of all emulsions remained above 92 % with no obvious phase separation or demulsification. These results suggested that the PPI/CL-CNCs-stabilized Pickering emulsions showed good physical stabilities. The study on the rheological properties and physical stabilities of PPI/CL-CNCs-based Pickering emulsions provided novel insights on developing highly stable Pickering emulsions.

Fabrication and Characterization of Functional Biobased Membranes from Postconsumer Cotton Fabrics and Palm Waste for the Removal of Dyes

Textile industries currently face vast challenges for the active removal of colored wastewater. Indeed, sustainable, recyclable, and green approaches are still lacking to achieve this aim. Thus, the present study explored the utilization of highly functional, green, recyclable, fully bio-based, and cost-effective composite membranes from post-consumer cotton fabrics and palm waste for wastewater treatment purposes. Highly functional cellulose nanofibers (CNF) were produced from waste cotton fabrics and filter paper using an acid hydrolysis technique. The yield of nanofibers extracted from waste cotton fabrics and filter paper was 76.74 and 54.50%, respectively. The physical, chemical, and structural properties of nanofibers were studied using various advanced analytical techniques. The properties of isolated nanofibers were almost similar and comparable to those of commercial nanofibers. The surface charge densities were -94.0, -80.7, and -90.6 mV for the nanofibers of palm waste, cotton fibers, and filter paper, respectively. After membrane fabrication using vacuum and hot-pressing techniques, the characteristics of the membrane were analyzed. The results showed that the average pore size of the palm-waste membrane was 1.185 nm, while it was 1.875 nm for membrane from waste cotton fibers and filter paper. Congo red and methylene blue dyes were used as model solutions to understand the behavior of available functional groups and the surface ζ-potential of the membrane frameworks' interaction. The membrane made from palm waste had the highest dye removal efficiency, and it was 23% for Congo red and 44% for methylene blue. This study provides insights into the challenges associated with the use of postconsumer textile and agricultural waste, which can be potentially used in high-performance liquid filtration devices for a more sustainable society.

Banana Peel Waste: An Emerging Cellulosic Material to Extract Nanocrystalline Cellulose

Nanocrystalline cellulose (NCC) has gained attention due to its versatile properties such as biocompatibility, sustainability, high aspect ratio, and abundance of -OH groups that favor modifications of NCC. The objective of this paper is to develop NCC by extracting and characterizing NCC prepared from banana peel powder (BPP). BPP was subjected to alkali and bleaching treatment to remove lignin and hemicellulose and then subjected to acid hydrolysis to prepare NCC. Under optimal conditions (200 mL of sulfuric acid 55% v/v at 50 °C for 60 min), the NCC yield was found to be 29.9%. The particle size and zeta potential of the NCC were found to be 209 nm and -43 mV, respectively. Attenuated total reflectance Fourier transform infrared spectroscopy showed successful removal of lignin and hemicellulose from BPP after the alkali treatment, bleaching, and acid hydrolysis. Field emission scanning electron microscopy showed needle-shaped crystals and transmission electron microscopy showed particles in the nano range. X-ray diffraction analysis showed that the crystallinity index of NCC was 64.12% while keeping the cellulose I crystal structure intact. Thermogravimetric analysis showed good stability which paves way for NCC to be explored for various applications. All the parameters evaluated indicated that NCC was successfully prepared from BPP using alkali treatment, bleaching, and acid hydrolysis.

Nanocellulose-Based Nanocomposites for Sustainable Applications: A Review

Nanocellulose has emerged in recent years as one of the most notable green materials available due to its numerous appealing factors, including its non-toxic nature, biodegradability, high aspect ratio, superior mechanical capabilities, remarkable optical properties, anisotropic shape, high mechanical strength, excellent biocompatibility and tailorable surface chemistry. It is proving to be a promising material in a range of applications pertinent to the material engineering to biomedical applications. In this review, recent advances in the preparation, modification, and emerging application of nanocellulose, especially cellulose nanocrystals (CNCs), are described and discussed based on the analysis of the latest investigations. This review presents an overview of general concepts in nanocellulose-based nanocomposites for sustainable applications. Beginning with a brief introduction of cellulose, nanocellulose sources, structural characteristics and the extraction process for those new to the area, we go on to more in-depth content. Following that, the research on techniques used to modify the surface properties of nanocellulose by functionalizing surface hydroxyl groups to impart desirable hydrophilic-hydrophobic balance, as well as their characteristics and functionalization strategies, were explained. The usage of nanocellulose in nanocomposites in versatile fields, as well as novel and foreseen markets of nanocellulose products, are also discussed. Finally, the difficulties, challenges and prospects of materials based on nanocellulose are then discussed in the last section for readers searching for future high-end eco-friendly functional materials.

Plant-Actuated Micro-Nanorobotics Platforms: Structural Designs, Functional Prospects, and Biomedical Applications

Plants are anatomically and physiologically different from humans and animals; however, there are several possibilities to utilize the unique structures and physiological systems of plants and adapt them to new emerging technologies through a strategic biomimetic approach. Moreover, plants provide safe and sustainable results that can potentially solve the problem of mass-producing practical materials with hazardous and toxic side effects, particularly in the biomedical field, which requires high biocompatibility. In this review, it is investigated how micro-nanostructures available in plants (e.g., nanoparticles, nanofibers and their composites, nanoporous materials, and natural micromotors) are adapted and utilized in the design of suitable materials for a micro-nanorobot platform. How plants' work on micro- and nanoscale systems (e.g., surface roughness, osmotically induced movements such as nastic and tropic, and energy conversion and harvesting) that are unique to plants, can provide functionality on the platform and become further prospective resources are examined. Furthermore, implementation across organisms and fields, which is promising for future practical applications of the plant-actuated micro-nanorobot platform, especially on biomedical applications, is discussed. Finally, the challenges following its implementation in the micro-nanorobot platform are also presented to provide advanced adaptation in the future.

Effective extraction of fluoroquinolones from water using facile modified plant fibers

In this study, ecofriendly and economic carboxy-terminated plant fibers (PFs) were used as adsorbents for the effective in-syringe solid phase extraction (IS-SPE) of fluoroquinolone (FQ) residues from water. Based on the thermal esterification and etherification reaction of cellulose hydroxy with citric acid (CA) and sodium chloroacetate in aqueous solutions, carboxy groups grafted onto cotton, cattail, and corncob fibers were fabricated. Compared with carboxy-terminated corncob and cotton, CA-modified cattail with more carboxy groups showed excellent adsorption capacity for FQs. The modified cattail fibers were reproducible and reusable with relative standard deviations of 3.2%–4.2% within 10 cycles of adsorption-desorption. A good extraction efficiency of 71.3%–80.9% was achieved after optimizing the extraction condition. Based on carboxylated cattail, IS-SPE coupled with ultra-performance liquid chromatography with a photodiode array detector was conducted to analyze FQs in environmental water samples. High sensitivity with limit of detections of 0.08–0.25 μg/L and good accuracy with recoveries of 83.8%–111.7% were obtained. Overall, the simple and environment-friendly modified waste PFs have potential applications in the effective extraction and detection of FQs in natural waters.

•

Plant fibers were functionalized by green methods.

•

The bio-adsorbents were applied for the extraction of fluoroquinolones.

•

The higher carboxy content in fibers improved extraction performance.

•

Carboxylated cattail was efficient in the adsorption of fluoroquinolones in environmental waters.

An Innovative Preparation, Characterization, and Optimization of Nanocellulose Fibers (NCF) Using Ultrasonic Waves

Recently, environmental and ecological concerns have become a major issue owing to the shortage of resources, high cost, and so forth. In my research, I present an innovative, environmentally friendly, and economical way to prepare nanocellulose from grass wastes with a sodium hypochlorite (NaClO) solution of different concentrations (1−6% mol) at different times 10−80 min, washed with distilled water, and treated with ultrasonic waves. The optimum yield of the isolated cellulose was 95%, 90%, and 87% NaClO at 25 °C for 20 min and with NaOH and H2SO4 at 25 °C with 5% M, respectively. The obtained samples were characterized by dynamic light scattering (DLS), Fourier-transform infrared (FT-IR) spectroscopy, and X-ray diffraction (XRD). The effect of test temperature and reaction times on the crystallinity index (IC) of GNFC with different treated mediums was carried out and investigated. The IC was analyzed using the diffraction pattern and computed according to the Segal empirical method (method A), and the sum of the area under the crystalline adjusted peaks (method B) and their values proved that the effect of temperature is prominent. In both methods, GNFC/H2SO4 had the highest value followed by GNFC/NaOH, GNFC/NaClO and real sample nano fiber cellulose (RSNFC). The infrared spectral features showed no distinct changes of the four cellulose specimens at different conditions. The particle size distribution data proved that low acid concentration hydrolysis was not sufficient to obtain nano-sized cellulose particles. The Zeta potential was higher in accordance with (GNFC/H2SO4 > GNFC/NaOH > GNFC/NaClO), indicating the acid higher effect.

Development of biodegradable films using sunflower protein isolates and bacterial nanocellulose as innovative food packaging materials for fresh fruit preservation

This study presents the valorization of side streams from the sunflower-based biodiesel industry for the production of bio-based and biodegradable food packaging following circular economy principles. Bacterial cellulose (BC) was produced via fermentation in 6 L static tray bioreactors using nutrient-rich supplements derived from the enzymatic hydrolysis of sunflower meal (SFM) combined with crude glycerol as carbon source. Novel biofilms were produced using either matrices of protein isolates extracted from sunflower meal (SFMPI) alone or SFMPI matrices reinforced with nanocellulose biofillers of commercial or bacterial origin. Acid hydrolysis was employed for ex-situ modification of BC to nanostructures (56 nm). The biofilms reinforced with bacterial nanocellulose structures (SFMPI-BNC) showed 64.5% higher tensile strength, 75.5% higher Young’s modulus, 131.5% higher elongation at break, 32.5% lower water solubility and 14.1% lower water vapor permeability than the biofilms produced only with SFMPI. The biofilms were evaluated on fresh strawberries packaging showing that the SFMPI-BNC-based films lead to effective preservation at 10 °C considering microbial growth and physicochemical profile (weight loss, chemical characterization, color, firmness and respiration activity). The SFMPI-BNC-based films could be applied in fresh fruit packaging applications.

Dietary fiber in bakery products: Source, processing, and function

Bakery products are prevalently consumed foods in the world, and they have been regarded as convenient dietary vehicles for delivering nutritive ingredients into people's diet, of which, dietary fiber (DF) is one of the most popular items. The food industry attempts to produce fiber-enriched bakery products with both increasing nutritional value and appealing palatability. As many new sources of DFs become available, and consumers are moving towards healthier diets, studies of using these DFs as functional ingredients in baked goods are becoming vast. Besides, the nutrition value of DF is commonly accepted, and many investigations have also revealed the health benefits of fiber-enriched bakery products. Thus, this chapter presents an overview of (1) trends in supplementation of DF from various sources, (2) impact of DF on dough processing, quality and physiological functionality of bakery products, and (3) technologies used to improve the compatibility of DF in bakery products.

Thermo-chemical potential of solid waste seed biomass obtained from plant Phoenix dactylifera and Aegle marmelos L. Fruit core cell

The present study explores thermo-chemical potential of two biomasses namely; Phoenix dactylifera seed (PDS) and Aegle marmelos L core (AMP). These biomasses contain high amount of cellulose and exhibit heating value of 3-18 MJ/kg. The thermal kinetic of both the biomasses have been extensively studied using thermogravimetric analysis (TGA) at four different heating rates 5, 10, 15, and 20 °C/min. Kinetic analysis was carried out using three model-free techniques including Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS) and Starink. The average activation energy has been found to be 173.75, 172.94 and 170.71 kJ/mol, for PDS whereas 170.26, 167.24 and 164.80 kJ/mol, for AMP analyzed through KAS, FWO and Starink methods, respectively. Further, among all these models, the Starink model exhibits better result for the biofuels potential point of view.

Almalki A, F Alkhanani M, Pal DB. Waste seeds of Mangifera indica, Artocarpus heterophyllus, and Schizizium commune as biochar for heavy metal removal from simulated wastewater

The threat of arsenic contamination in water is a challenging issue worldwide. Millions of people utilize untreated groundwater having high levels of arsenic in developing countries. Design Expert 6.0.8 has been used to design experiments and carried out statistical analysis for optimization of different parameters. It is of prime importance to develop cheap environment friendly bio-sorbent for protecting health of the poor from ill effects of arsenic. In the present investigation, we prepared bio-sorbent from the solid waste seed biomass of Mangifera indica (M), Artocarpus heterophyllus (JF), and Schizizium commune (JP). The characterization of bio-sorbents has been done by using different techniques namely FTIR and XRD. Arsenic concentration was estimated using ICP and adsorption parameters optimized for pH, adsorbent dose, and initial arsenic concentration. At pH 8.4, kinetics study of arsenic removal was M (94%), JF (93%), and JP (92%) for initial concentration of 2.5 ppm. The adsorption kinetics was well explained by Freundlich model and pseudo-second reaction order.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s13399-021-02078-5.

Natural Fiber-Reinforced Polylactic Acid, Polylactic Acid Blends and Their Composites for Advanced Applications

Polylactic acid (PLA) is a thermoplastic polymer produced from lactic acid that has been chiefly utilized in biodegradable material and as a composite matrix material. PLA is a prominent biomaterial that is widely used to replace traditional petrochemical-based polymers in various applications owing environmental concerns. Green composites have gained greater attention as ecological consciousness has grown since they have the potential to be more appealing than conventional petroleum-based composites, which are toxic and nonbiodegradable. PLA-based composites with natural fiber have been extensively utilized in a variety of applications, from packaging to medicine, due to their biodegradable, recyclable, high mechanical strength, low toxicity, good barrier properties, friendly processing, and excellent characteristics. A summary of natural fibers, green composites, and PLA, along with their respective properties, classification, functionality, and different processing methods, are discussed to discover the natural fiber-reinforced PLA composite material development for a wide range of applications. This work also emphasizes the research and properties of PLA-based green composites, PLA blend composites, and PLA hybrid composites over the past few years. PLA's potential as a strong material in engineering applications areas is addressed. This review also covers issues, challenges, opportunities, and perspectives in developing and characterizing PLA-based green composites.

Cationized high amylose maize starch films reinforced with borax cross-linked nanocellulose

In this study, a novel strategy for modifying nanocellulose (NC) by borax cross-linking was developed, and the obtained borax modified nanocellulose (BNC) was incorporated into cationized high amylose maize starch (CS) films to evaluate the applicability. Cellulose molecules were successfully cross-linked by boron ester bonds, and the original crystal type and basic chemical structure were not changed. Compared with NC, the relative crystallinity of BNC was slightly increased, and the thermal stability was obviously enhanced. Addition of NC and BNC to CS films significantly improved their tensile strength and water resistance. The dispersion of nanocellulose in CS films was effectively improved by borax cross-linking modification. CS/BNC films showed higher mechanical and water resistance properties compared with CS/NC films. Compared with pure CS film, tensile strength of the composite film with 6 wt% BNC increased about 4.0 times, and its water-vapor permeability decreased about 37%. The novel strategy for preparing BNC by using boron ester bonds will provide a potential approach for the development of starch films with desirable properties.

A critical review on the techniques used for the synthesis and applications of crystalline cellulose derived from agricultural wastes and forest residues

In order to meet the growing energy crisis of the 21st century, the utilization of bio-based materials has become a field of high research endeavour. In view of that, the present review paper is focused on different techniques that are frequently explored for the synthesis of value-added crystalline derivatives of cellulose like MCC and NCC from agricultural wastes and forest residues. Moreover, a comparative analysis between thermochemical and biochemical methods is carried out for such valorization of biomass considering the mechanism involved with various reactions. Further, a critical analysis is performed on various individual techniques specifically used for the applications of MCC and NCC in different fields including environmental, polymer industry, pharmaceutical and other emerging sectors. This article will assist the readers not only to explore new biomass sources but also provides an in-depth insight on various green and cost-effective methods for sustainable production of crystalline cellulose.

Alkaline pretreatment and response surface methodology based recombinant enzymatic saccharification and fermentation of sugarcane tops

In present study, the water-soluble extractives removal prior to alkali pretreatment of sugarcane tops (SCT) was carried out. The solid alkali pretreated SCT (apSCT) recovered on Field-emission scanning electron microscopy (FE-SEM) analysis showed exposure of cellulosic fibres as compared with raw SCT. The analyses of apSCT by Fourier Transform Infrared (FT-IR) Spectroscopy, X-ray diffraction (XRD) and High performance liquid chromatography (HPLC) analysis also confirmed the enhanced cellulose content in apSCT. Optimum conditions for response surface methodology based saccharification of apSCT at 40 °C, 150 rpm were 2.14% (w/v) apSCT loading in citrate-phosphate buffer (50 mM, pH 6.0), recombinant hydrolytic enzymes (from Clostridium/Hungateiclostridium thermocellum) loading for endo-1,4-β-glucanase (CtCel8A) = 213.2 U/g, cellobiohydrolase (CtCBH5A) = 272.5 U/g and β-glucosidase (HtBg1) = 299.8 U/g for 49.2 h. Under optimized saccharification conditions, the total reducing sugar yield was 265 mg/g (glucose 214 mg/g) of apSCT. Fermentation of produced glucose by S. cerevisiae gave 0.19 g/g glucose of bioethanol.

Nanocrystalline Cellulose from Microcrystalline Cellulose of Date Palm Fibers as a Promising Candidate for Bio-Nanocomposites: Isolation and Characterization

Date palm fiber (Phoenix dactylifera L.) is a natural biopolymer rich in lignocellulosic components. Its high cellulose content lends them to the extraction of tiny particles like microcrystalline cellulose (MCC) and nanocrystalline cellulose (NCC). These cellulose-derived small size particles can be used as an alternative biomaterial in wide fields of application due to their renewability and sustainability. In the present work, NCC (A) and NCC (B) were isolated from date palm MCC at 60 min and 90 min hydrolysis times, respectively. The isolated NCC product was subjected to characterization to study their properties differences. With the hydrolysis treatment, the yields of produced NCC could be attained at between 22% and 25%. The infrared-ray functional analysis also revealed the isolated NCC possessed a highly exposed cellulose compartment with minimized lignoresidues of lignin and hemicellulose. From morphology evaluation, the nanoparticles’ size was decreased gradually from NCC (A) (7.51 nm width, 139.91 nm length) to NCC (B) (4.34 nm width, 111.51 nm length) as a result of fragmentation into cellulose fibrils. The crystallinity index was found increasing from NCC (A) to NCC (B). With 90 min hydrolysis time, NCC (B) showed the highest crystallinity index of 71% due to its great cellulose rigidity. For thermal analysis, NCC (B) also exhibited stable heat resistance, in associating with its highly crystalline cellulose structure. In conclusion, the NCC isolated from date palm MCC would be a promising biomaterial for various applications such as biomedical and food packaging applications.

Java plum and amaltash seed biomass based bio-adsorbents for synthetic wastewater treatment

Biomass of Java plum (JP) and amaltash (AT) seeds were employed to remove arsenic from synthetic wastewater, cost effectively. The prepared biomasses were characterized by FE-SEM, EDX, FTIR, XRD, and ICP techniques. Experimentation the optimization study has been carried out by using Design-software 6.0.8. Response surface methodology has been applied to design the experiments where we have used three factors and three levels Box-Behnken design (BBD). Arsenic removal ability of bio-sorbents was evaluated and optimized by varying pH, adsorbent dose concentration of arsenic in synthetic wastewater. For 2.5 mg/L arsenic concentration and 80 mg adsorbent dose at pH 8.8 Java plum seeds (JP) based bio-adsorbent removed ∼93% and amaltash seeds (AT) based bio-adsorbent removed ∼91% arsenic from synthetic wastewater. The adsorption behaviour better explained following Freundlich model (R² = 0.99) compared to Temkin model (R² = 0.986) for As (III) ions. The adsorption capacity was 1.45 mg g^-1 and 1.42 mg g^-1 for JP and AT, respectively after 80 min under optimal set of condition. The adsorption kinetics was explained by either pseudo-first order model or Elovich model.

A review of nanocellulose as a new material towards environmental sustainability

Synthetic polymers, commonly referred to as plastics, are anthropogenic contaminants that adversely affect the natural ecosystems. The continuous disposal of long lifespan plastics has resulted in the accumulation of plastic waste, leading to significant pollution of both marine and terrestrial habitats. Scientific pursuit to seek environment-friendly materials from renewable resources has focused on cellulose, the primary reinforcement component of the cell wall of plants, as it is the most abundantly available biopolymer on earth. This paper provides an overview on the current state of science on nanocellulose research; highlighting its extraction procedures from lignocellulosic biomass. Literature shows that the process used to obtain nanocellulose from lignocellulosic biomass greatly influences its morphology, properties and surface chemistry. The efficacy of chemical methods that use alkali, acid, bleaching agents, ionic liquids, deep eutectic solvent for pre-treatment of biomass is discussed. There has been a continuous endeavour to optimize the pre-treatment protocol as it is specific to lignocellulosic biomass and also depends on factors such as nature of the biomass, process and environmental parameters and economic viability. Nanofibers are primarily isolated through mechanical fibrillation while nanocrystals are predominantly extracted using acid hydrolysis. A concise overview on the ways to improve the yield of nanocellulose from cellulosic biomass is also presented in this review. This work also reviews the techniques used to modify the surface properties of nanocellulose by functionalizing surface hydroxyl groups to impart desirable hydrophilic-hydrophobic balance. An assessment on the emerging application of nanocellulose with an emphasis on development of nanocomposite materials for designing environmentally sustainable products is incorporated. Finally, the status of the industrial production of nanocellulose presented, which indicates that there is a continuously increased demand for cellulose nanomaterials. The demand for cellulose is expected to increase further due to its increasing and broadening applications.

Effect of cellulose and starch fatty acid esters addition on microstructure and physical properties of arabinoxylan films

Arabinoxylan (AX) and cellulose were extracted from wheat straw, whereas starch was extracted from potato peel. Thereafter, cellulose and starch were esterified with lauric, myristic, palmitic and stearic acids to prepare corresponding cellulose (CFAs) and starch fatty acid esters (SFAs) with DS 2.1-2.8. XRD study revealed remarkable loss of crystallinity in cellulose and starch due to fatty acid esterification. The addition of palmitate and stearate esters of cellulose and starch to AX formed laminar film microstructures which limited water vapor permeability whereas films prepared by blending AX with laurate and myristate esters of starch and cellulose were less effective as water vapor barrier due to their non-layer microstructures. The laminar structures also resulted significant reduction in mechanical strength of the composite films. Furthermore, all AX-CFAs and AX-SFAs films were thermally more stable than native composite films. These films might be used to produce industrially useful coating material for food products.

Synthesis and properties of organoboron functionalized nanocellulose for crosslinking low polymer fracturing fluid system

The traditional organoboron crosslinker used in the guar gum fracturing fluid has the disadvantages of a larger amount of guar gum and crosslinker and higher susceptibility to pH. Nanoparticles have special properties such as large specific surface area and many active groups, so the organic boron crosslinker and nanoparticles are combined to obtain nano crosslinkers. In this paper, rod-shaped nano-cellulose particles were prepared by acid hydrolysis, and a nanocellulose crosslinker was synthesized by combining with organic boron and KH550. Nanocellulose cross-linker has good temperature and salt resistance. It can meet the requirements of cross-linking guar gum fracturing fluid with a mass fraction of 0.3 wt% under neutral conditions. The residual viscosity is higher than 50 mPa s under shear at 170 s-1 and 110 °C for 60 minutes when the pH increases from 7 to 13, and NBC crosslinking can withstand a temperature of 160 °C under pH = 10. The crosslinking mechanism of the widely accepted nano-crosslinker is that the organoboron on the surface of the nanoparticle combines with the homeopathic ortho hydroxyl of the guar gum molecule to form a hydrogen bond and thereby form a complex network structure. This research shows that the hydrogen bonding between the nano-cellulose crosslinker and HPG molecules, and the resulting gel has a more complex network structure because of the formation of inter-chain cross-links.

Immobilization of β-galactosidase by halloysite-adsorption and entrapment in a cellulose nanocrystals matrix

BACKGROUND

Immobilization allows easy recovery and reuse of enzymes in industrial processes. In addition, it may enhance enzyme stability, allowing prolonged use. A simple and novel method of immobilizing β-galactosidase is reported. Effects of immobilization on the enzyme characteristics are explained. β-Galactosidase is well established in dairy processing and has emerging applications in novel syntheses.

METHODS

β-Galactosidase was immobilized by physical adsorption on halloysite, an aluminosilicate nanomaterial. Optimal conditions for adsorption were identified. The optimally prepared halloysite-adsorbed enzyme was then entrapped in a porous matrix of nanocrystals of sulfated bacterial cellulose, to further enhance stability.

RESULTS

Under optimal conditions, 89.5% of the available protein was adsorbed per mg of halloysite. The most active and stable final immobilized biocatalyst had 1 part by mass of the enzyme-supporting halloysite particles mixed with 2 parts of cellulose nanocrystals. Immobilization raised the optimal pH of the catalyst to 7.5 (from 6.0 for the native enzyme) and temperature to 55 °C (40 °C for the native enzyme). During storage at 25 °C, the immobilized enzyme retained 75.8% of initial activity after 60 days compared to 29.2% retained by the free enzyme.

CONCLUSION

The immobilization method developed in this work enhanced enzyme stability during catalysis and storage. Up to 12 cycles of repeated use of the catalyst became feasible.

GENERAL SIGNIFICANCE

The simple and rapid immobilization strategy of this work is broadly applicable to enzymes used in diverse bioconversions.

Fabrication and Characterization of Novel Poly(D-lactic acid) Nanocomposite Membrane for Water Filtration Purpose

The development of membrane technology from biopolymer for water filtration has received a great deal of attention from researchers and scientists, owing to the growing awareness of environmental protection. The present investigation is aimed at producing poly(D-lactic acid) (PDLA) membranes, incorporated with nanocrystalline cellulose (NCC) and cellulose nanowhisker (CNW) at different loadings of 1 wt.% (PDNC-I, PDNW-I) and 2 wt.% (PDNC-II PDNW-II). From morphological characterization, it was evident that the nanocellulose particles induced pore formation within structure of the membrane. Furthermore, the greater surface reactivity of CNW particles facilitates in enhancing the surface wettability of membranes due to increased hydrophilicity. In addition, both thermal and mechanical properties for all nanocellulose filled membranes under investigation demonstrated significant improvement, particularly for PDNW-I-based membranes, which showed improvement in both aspects. The membrane of PDNW-I presented water permeability of 41.92 L/m²h, when applied under a pressure range of 0.1-0.5 MPa. The investigation clearly demonstrates that CNWs-filled PDLA membranes fabricated for this investigation have a very high potential to be utilized for water filtration purpose in the future.

Preparation and characterization of cellulose nanocrystal extracted from ramie fibers by sulfuric acid hydrolysis

Cellulose nanocrystals (CNCs) were isolated from ramie fibers through chemical pretreatments accompanied by sulfuric acid hydrolysis. The influences of both temperature and hydrolysis time on the properties of CNCs were discussed in the present study. The characterization of CNCs was conducted using FT-IR, XRD, TEM, and TGA. The results showed the characteristics of obtained CNCs were influenced significantly by both temperature and time of hydrolysis. The crystallinity, dimensions, and thermal stability of CNCs were found to reduce by increasing both temperature and reaction time of hydrolysis. The optimal hydrolysis parameters were achieved at 45 °C for 30 min with 58% sulfuric acid to produce CNCs, rod-like particles with a high crystallinity (90.77%), diameter (6.67 nm), length (145.61 nm), and best thermal stability among all CNCs. The obtained CNCs had a higher potential for application of alternative reinforcing fillers in the nanocomposites.

A correlation on ultrasonication with nanocrystalline cellulose characteristics

Catalytic ionic liquid hydrolysis of cellulosic material have been considered as a green and highly efficient dissolution process. However, application of a pre-treatment process, i.e; ultrasonication enhances the hydrolysis of cellulose in ionic liquid by providing mechanical force. In this paper, we describe the impact of both chemical and mechanical approaches to produce nanocrytalline cellulose (NCC) with anticipated particle size, and crystallinity with improved yields. The ultrasonication treatment was evaluated in terms of treatment time and vibration amplitude. It was found that the lowest ultrasonication time (5 min) produced the NCC of highest crystallinity (73 %), but the lowest yield (84 %). In contrary, the highest ultrasonication vibration amplitude at 90 % produced NCC with highest crystallinity value (67 %) as well as yields (90 %). It concludes that ultrasonic pre-treatment improves the hydrolysis process of cellulose in ionic liquid with increasing yield and crystallinity of NCC.

Structural, Morphological and Thermal Properties of Cellulose Nanofibers from Napier fiber (Pennisetum purpureum)

The purpose of the study is to investigate the utilisation of Napier fiber (Pennisetum purpureum) as a source for the fabrication of cellulose nanofibers (CNF). In this study, cellulose nanofibers (CNF) from Napier fiber were isolated via ball-milling assisted by acid hydrolysis. Acid hydrolysis with different molarities (1.0, 3.8 and 5.6 M) was performed efficiently facilitate cellulose fiber size reduction. The resulting CNFs were characterised through Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), particle size analyser (PSA), field-emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), and transmission electron microscopy (TEM). The FTIR results demonstrated that there were no obvious changes observed between the spectra of the CNFs with different molarities of acid hydrolysis. With 5.6 M acid hydrolysis, the XRD analysis displayed the highest degree of CNF crystallinity at 70.67%. In a thermal analysis by TGA and DTG, cellulose nanofiber with 5.6 M acid hydrolysis tended to produce cellulose nanofibers with higher thermal stability. As evidenced by the structural morphologies, a fibrous network nanostructure was obtained under TEM and AFM analysis, while a compact structure was observed under FESEM analysis. In conclusion, the isolated CNFs from Napier-derived cellulose are expected to yield potential to be used as a suitable source for nanocomposite production in various applications, including pharmaceutical, food packaging and biomedical fields.

Fabrication and characterization of cellulose nanoparticles from maize stalk pith via ultrasonic-mediated cationic etherification

In this study, parenchyma cellulose, which was extracted from maize stalk pith as an abundant source of agricultural residues, was applied for preparing cellulose nanoparticles (CNPs) via an ultrasound-assisted etherification and a subsequent sonication process. The ultrasonic-assisted treatment greatly improved the modification of the pith cellulose with glycidyltrimethylammonium chloride, leading to a partial increase in the dissolubility of the as-obtained product and thus disintegration of sheet-like cellulose into nanoparticles. While the formation of CNPs by ultrasonication was largely dependent on the cellulose consistency in the cationic-modified system. Under the condition of 25% cellulose consistency, the longer sono-treated duration yielded a more stable and dispersible suspension of CNP due to its higher zeta potential. Degree of substitution and FT-IR analyses indicated that quaternary ammonium salts were grafted onto hydroxyl groups of cellulose chain. SEM and TEM images exhibited the CNP to have spherical morphology with an average dimeter from 15 to 55 nm. XRD investigation revealed that CNPs consisted mainly of a crystalline cellulose Ι structure, and they had a lower crystallinity than the starting cellulose. Moreover, thermogravimetric results illustrated the thermal resistance of the CNPs was lower than the pith cellulose. The optimal CNP with highly cationic charges, good stability and acceptable thermostability might be considered as one of the alternatively renewable reinforcement additives for nanocomposite production.