Chitosan‑g‑maleic acid for effective removal of copper and nickel ions from their solutions

Study on Adsorption of Cd in Solution and Soil by Modified Biochar-Calcium Alginate Hydrogel

Contamination with cadmium (Cd) is a prominent issue in agricultural non-point source pollution in China. With the deposition and activation of numerous Cd metal elements in farmland, the problem of excessive pollution of agricultural produce can no longer be disregarded. Considering the issue of Cd pollution in farmland, this study proposes the utilization of cross-linked modified biochar (prepared from pine wood) and calcium alginate hydrogels to fabricate a composite material which is called MB-CA for short. The aim is to investigate the adsorption and passivation mechanism of soil Cd by this innovative composite. The MB-CA exhibits a higher heavy metal adsorption capacity compared to traditional biochar and hydrogel due to its increased oxygen-containing functional groups and heavy metal adsorption sites. In the Cd solution adsorption experiment, the highest Cd2+ removal rate reached 85.48%. In addition, it was found that the material also has an excellent pH improvement effect. Through the adsorption kinetics experiment and the soil culture experiments, it was determined that MB-CA adheres to the quasi-second-order kinetic model and is capable of adsorbing 35.94% of Cd2+ in soil. This study validates the efficacy of MB-CA in the adsorption and passivation of Cd in soil, offering a novel approach for managing Cd-contaminated cultivated land.

Enhancing Wastewater Depollution: Sustainable Biosorption Using Chemically Modified Chitosan Derivatives for Efficient Removal of Heavy Metals and Dyes

Driven by concerns over polluted industrial wastewater, particularly heavy metals and dyes, this study explores biosorption using chemically cross-link chitosan derivatives as a sustainable and cost-effective depollution method. Chitosan cross-linking employs either water-soluble polymers and agents like glutaraldehyde or copolymerization of hydrophilic monomers with a cross-linker. Chemical cross-linking of polymers has emerged as a promising approach to enhance the wet-strength properties of materials. The chitosan thus extracted, as powder or gel, was used to adsorb heavy metals (lead (Pb2+) and copper (Cu2+)) and dyes (methylene blue (MB) and crystal violet (CV)). Extensive analysis of the physicochemical properties of both the powder and hydrogel adsorbents was conducted using a range of analytical techniques, including Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), and scanning electron microscopy (SEM), as well as 1H and 13C nuclear magnetic resonance (NMR). To gain a comprehensive understanding of the sorption process, the effect of contact time, pH, concentration, and temperature was investigated. The adsorption capacity of chitosan powder for Cu(II), Pb(II), methylene blue (MB), and crystal violet (CV) was subsequently determined as follows: 99, 75, 98, and 80%, respectively. In addition, the adsorption capacity of chitosan hydrogel for Cu(II), Pb(II), MB, and CV was as follows: 85, 95, 85, and 98%, respectively. The experimental data obtained were analyzed using the Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models. The isotherm study revealed that the adsorption equilibrium is well fitted to the Freundlich isotherm (R2 = 0.998), and the sorption capacity of both chitosan powder and hydrogel was found to be exceptionally high (approximately 98%) with the adsorbent favoring multilayer adsorption. Besides, Dubinin has given an indication that the sorption process was dominated by Van der Waals physical forces at all studied temperatures.

Fabrication and characterization of a new eco-friendly sulfonamide-chitosan derivative with enhanced antimicrobial and selective cytotoxicity properties

Chitosan (CH) exhibits low antimicrobial activity. This study addresses this issue by modifying the chitosan with a sulfonamide derivative, 3-(4-(N,N-dimethylsulfonyl)phenyl)acrylic acid. The structure of the sulfonamide-chitosan derivative (DMS-CH) was confirmed using Fourier transform infrared spectroscopy and Nuclear magnetic resonance. The results of scanning electron microscopy, thermal gravimetric analysis, and X-ray diffraction indicated that the morphology changed to a porous nature, the thermal stability decreased, and the crystallinity increased in the DMS-CH derivative compared to chitosan, respectively. The degree of substitution was calculated from the elemental analysis data and was found to be moderate (42%). The modified chitosan exhibited enhanced antimicrobial properties at low concentrations, with a minimum inhibitory concentration (MIC) of 50 µg/mL observed for B. subtilis and P. aeruginosa, and a value of 25 µg/mL for S. aureus, E. coli, and C. albicans. In the case of native chitosan, the MIC values doubled or more, with 50 µg/mL recorded for E. coli and C. albicans and 100 μg/mL recorded for B. subtilis, S. aureus, and P. aeruginosa. Furthermore, toxicological examinations conducted on MCF-7 (breast adenocarcinoma) cell lines demonstrated that DMS-CH exhibited greater toxicity (IC50 = 225.47 μg/mL) than pure CH, while still maintaining significant safety limits against normal lung fibroblasts (WI-38). Collectively, these results suggest the potential use of the newly modified chitosan in biomedical applications.

Targeted elimination of molybdenum ions from a leaching solution with the ability of radiated grafting GMA-PAN nanofibers

In this study, electrospun polyacrylonitrile nanofibers were effectively functionalized for enhanced molybdenum ion adsorption through a multi-step approach. Initially, glycidyl methacrylate was grafted onto the nanofibers via irradiation-induced grafting polymerization, followed by chemical modification with various amino groups, with triethylamine identified as the optimal modifier. The impacts of key synthesis parameters and reaction conditions on grafting level and adsorption capacity were thoroughly investigated, with a focus on achieving maximum efficiency. The resulting nanofibers were characterized using FTIR, SEM, and BET techniques, confirming the successful modification and structural features conducive to adsorption. Furthermore, a comprehensive experimental design, incorporating a central composite design, yielded optimal conditions for molybdenum adsorption, with key parameters including monomer concentration, irradiation dose, adsorbent mass, initial concentration, time, pH, temperature, and amine concentration. The adsorption kinetics were effectively described by the pseudo-second-order model, while the Langmuir isotherm model provided valuable insight into the adsorption behavior. Impressively, the adsorbent exhibited exceptional adsorption efficiency, surpassing 98% even after six adsorption-desorption cycles using 0.5 M HCl. Thermodynamic analysis revealed the exothermic nature of the adsorption process, along with decreased entropy and overall spontaneity, underlining the favorable conditions for molybdenum adsorption. Notably, the synthesized adsorbent demonstrated notable selectivity for molybdenum and achieved an impressive adsorption capacity of 109.79 mg/g, highlighting its potential for practical applications in molybdenum removal from aqueous solutions.

Polydopamine-functionalized electrospun poly(vinyl alcohol)/chitosan nanofibers for the removal and determination of Cu(II)

Environmentally friendly and recycled polydopamine-functionalized electrospun poly(vinyl alcohol)/chitosan nanofibers (PVA/CS/PDA) were prepared through a low-energy-consumption procedure. The PDA coating endows PVA/CS/PDA nanofibers with good water stability. The PVA/CS/PDA nanofibers have a fibrillar and porous structure that is favorable for Cu(II) to access the active sites of the nanofibers. The adsorption isotherm and kinetics data preferably conform to the Liu isotherm and pseudo-second-order kinetic models, respectively. The maximum adsorption capacity of Cu(II) ions by PVA/CS/PDA nanofibers from the Liu isotherm model is 326.5 mg g-1. The PVA/CS/PDA nanofibers exhibit higher adsorption capacity than some other reported adsorbents. The adsorption mechanism study demonstrates that the Cu(II) adsorption is mainly ascribed to the complexation of Cu(II) with the imino, amino, and hydroxy moieties in PVA/CS/PDA nanofibers. The nanofibers can be employed for 5 cycles without significantly deteriorating performance. More interestingly, a fluorometry method based on the oxidation mimic enzyme activity of Cu(II) was developed to detect low concentrations of Cu(II) using the nanofibers as an adsorbent to preconcentrate Cu(II). The limit of detection is 0.42 mg L-1. The successful removal and detection of Cu(II) in Pearl River and mineral water samples demonstrates the great potential of PVA/CS/PDA nanofibers to remediate Cu(II)-polluted water.

Removal of Pb (II) and Zn (II) in the mineral beneficiation wastewater by using cross-linked carboxymethyl starch-g-methacrylic acid as an effective flocculant

The cross-linked carboxymethyl starch-g-methacrylic acid (CCMS-g-MAA) was prepared by using grafting and micro-cross-linking in the one-pot preparation process. CCMS-g-MAA presented high removal capacity of Pb (II) of 57.13 mg/g at pH = 4 and high removal capacity of Zn (II) of 51.41 mg/g at pH = 5 by using a sample dosage of 0.68 g/L. Characterization results of FTIR, TG, and XRD illustrate that methacrylic acid and sodium tri-metaphosphate were successfully introduced into the structure of carboxymethyl starch. SEM characterization presented that the sample particles were amorphous aggregates with surface voids, which was favorable for the adsorption of heavy metal ions from wastewater. Adsorption isotherm results indicated that Freundlich equation could be better used to describe the adsorption process of metal ions on CCMS-g-MAA. The adsorption kinetic results indicated that the pseudo-second-order model is more suitable to describe this removal process. XPS results indicated that metal ions interacted with functional groups on the surface of flocculant, especially carboxyl groups. The removal process may be purposed that metal ions were adsorbed by porous material, and then combined with surface functional groups of the flocculant via electrostatic interaction, chelation or ion exchange. Subsequently, metal ions were separated from the wastewater with flocs precipitated in the bottom of solution via bridging and patching. The obtained results illustrated that CCMS-g-MAA was an effective material for the treatment of wastewater containing polymetallic ions besides mineral beneficiation wastewater supported by its excellent regeneration.

Cellulose phosphonate/polyethyleneimine nano-porous composite remove toxic Pb(II) and Cu(II) from water in a short time

Current cellulose-based adsorbents suffer from the drawbacks of low adsorption capacity or slow adsorption rate for heavy metal ions. It is imperative to prepare new cellulose-based materials to improve the adsorption ability. In this work, we aim to introduce phosphonate groups to improve the adsorption ability of cellulose and select polyethyleneimine (PEI) for synergistic adsorption. A novel cellulose phosphonate/polyethyleneimine composite (MCCP-PEI) is prepared via the Mannich reaction. The structure and composition of MCCP-PEI are characterized by various advanced microscopy and spectroscopy techniques, and the results show that MCCP-PEI possesses abundant nano-porous structure, strong chelating sites, and excellent hydrophilicity. Besides, the adsorption behavior of MCCP-PEI for heavy metals has been systematically investigated. The results show that the adsorbent can quickly remove toxic Cu(II) and Pb(II) from water within 15 min and 20 min, respectively. The saturated adsorption capacity for Cu(II) and Pb(II) is 250.0 and 534.7 mg·g-1, respectively. X-ray photoelectron spectroscopy analysis combined with Density Functional Theory calculations reveal that the adsorption mechanism is chemical complexation and electrostatic attraction, and the phosphonate group plays a key role in the adsorption process.

Sustainable grafted chitosan-dialdehyde cellulose with high adsorption capacity of heavy metal

A novel adsorbent was prepared using a backbone comprising chemically hybridized dialdehyde cellulose (DAC) with chitosan via Schiff base reaction, followed by graft copolymerization of acrylic acid. Fourier transform infrared spectroscopy (FTIR) confirmed the hybridization while scanning electron microscopy (SEM) revealed intensive covering of chitosan onto the surface of DAC. At the same time, energy dispersive X-ray (EDX) proved the emergence of nitrogen derived from chitosan. The X-ray diffraction (XRD) indicated that the crystallinity of the backbone and graft copolymer structures was neither affected post the hybridization nor the grafting polymerization. The adsorbent showed high swelling capacity (872%) and highly efficient removal and selectivity of Ni2+ in the presence of other disturbing ions such as Pb2+ or Cu2+. The kinetic study found that the second-order kinetic model could better describe the adsorption process of (Cu2+, Ni2+) on the graft copolymer. In contrast, the first-order kinetic model prevails for the binary mixture (Pb2+, Ni2+). Moreover, the correlation coefficient values for the adsorption process of these binary elements using Langmuir and Freundlich isotherms confirmed that the developed grafted DAC/chitosan exhibits a good fit with both isotherm models, which indicates its broadened and complicated structure. Furthermore, the grafted DAC/chitosan exhibited high efficient regeneration and high adsorption capacity for Pb2+, Cu2+ and Ni2+.

Development of a chitosan derivative bearing the thiadiazole moiety and evaluation of its antifungal and larvicidal efficacy

A new chitosan derivative bearing a new thiadiazole compound was developed, and its antifungal and larvicidal activities were investigated. The chitosan derivative (coded here as PTDz-Cs) was synthesized by the reaction between the carboxylic derivative of the thiadiazole moiety and chitosan. Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance (1H/13C-NMR), gas chromatography–mass spectrometry (GC–MS), elemental analysis, X-Ray diffraction (XRD), thermogravimetric analysis (TGA), and X-ray photoelectron spectroscopy (XPS) were used to characterize the developed derivatives. Compared to chitosan, the PTDz-Cs derivative has a less crystalline structure and less thermal stability. The antifungal results revealed that PTDz-Cs exhibited potential activity against Rhizopus microspores, Mucor racemosus, Lichtheimia corymbifera, and Syncephalastrum racemosum where inhibition zones were 17.76, 20.1, 38.2, and 18.3 mm, respectively. The larvicidal efficacy of the PTDz-Cs derivative against A. stephensi larvae was tested, and the results exposed that the LC50 and LC90 values (first instar) were 5.432 and 10.398 ppm, respectively, indicating the high susceptibility of early instar mosquito larvae to PTDz-Cs. These results emphasize that this study provided a new chitosan derivative that could be potentially used in the biomedical fields.

Adsorption of Pb (II) and Cu (II) by magnetic beads loaded with xanthan gum

Green and environmentally friendly and efficient separation adsorbents have attracted much attention in the treatment of heavy metal ions wastewater. In this study, xanthan gum (XG) was supported by fly ash magnetic beads (FAMB) to prepare adsorbent XG@FAMB. The effects of XG@FAMB dosage, pH value of the solution, adsorption time, and initial Pb (II) and Cu (II) concentration on its adsorption performance for Pb (II) and Cu (II) were investigated. The results show that under the conditions of pH 6, dosage of XG@FAMB 4.0 g/L, adsorption time 120 min, and initial concentration 60 mg/L, the maximum adsorption capacity of XG@FAMB for Pb (II) and Cu (II) was 14.93 mg/g and 14.88 mg/g, respectively. The adsorption process of Pb (II) and Cu (II) by XG@FAMB could be better described by the quasi-second-order kinetic model and Langmuir isothermal adsorption model, that is, the adsorption process is monolayer adsorption controlled by chemical action. The adsorption mechanism is that Pb (II) and Cu (II) coordinate with oxygen-containing functional groups hydroxyl and carboxyl on XG@FAMB surface, accompanied by electrostatic adsorption. XG@FAMB has the advantages of environmental protection of XG and easy solid-liquid separation of FAMB, and has a good removal effect on Pb (II) and Cu (II).

Effect of ternary polymer composites of macroporous adsorbents on adsorption properties for heavy metal removal from aqueous solution

This research is focused on the preparation of macroporous poly(vinyl alcohol) (PVA)/chitosan (CS)/Al₂O₃ adsorbents for removal of residual metal ions from wastewater. The PVA/CS/Al₂O₃ adsorbents were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), and energy dispersive X-ray (EDX) techniques to confirm that all compositions were incorporated into the PVA/CS/Al₂O₃ adsorbents without chemical modification. Furthermore, a comparison of the properties of the PVA/CS/Al₂O₃ adsorbents suggested that PVA/CS/0.50Al₂O₃ was the most suitable sample for adsorption study. The adsorption properties of PVA/CS/0.50Al₂O₃ for the removal of metal ions such as Pb²⁺, Cu²⁺, Zn²⁺, and Ni²⁺ in aqueous solution adsorbents in both single and quaternary systems were investigated. The results show that the adsorption selectivity of the PVA/CS/0.50Al₂O₃ adsorbent for these metal ions was provided in the following order: Pb²⁺  > Cu²⁺  > Zn²⁺  > Ni²⁺. The adsorption isotherm was studied by equilibrium data obtained from batch experiments. It was found that the Freundlich isotherm model was suitable for explaining the adsorption process. Adsorption kinetics were studied, which indicated that the adsorption of Pb²⁺, Cu²⁺, and Zn²⁺ followed a pseudo-second-order kinetic model, while the adsorption of Ni²⁺ followed a pseudo-first-order kinetic model. In addition, adsorption-desorption cycles were studied to prove the reusability of PVA/CS/0.50Al₂O₃ adsorbents. The PVA/CS/0.50Al₂O₃ adsorbents were able to be regenerated and reused. In a continuous adsorption process, a column experiment was simulated in laboratory. The results showed that Cu²⁺ was the most selective for a fixed-bed column. Thus, PVA/CS/0.50Al₂O₃ adsorbents could be potential used for toxic metal ion removal from wastewater, in both batch and fixed-bed continuous-flow columns.

Amidoxime functionalized chitosan for uranium sequestration in vivo

Amidoxime functionalized chitosan (AC) was recommended as a chelator for uranium sequestration in vivo in this study, and the structure-activity relationship was also explored. Compared with ZnNa₃-DTPA, which was a commercial uranium mobilization drug, AC exhibited excellent biocompatibility and uranium removal efficiency, whether by injection or orally, which could reduce the amounts of uranium deposited in kidneys and femurs by up to 43.6% and 32.3%. In particular, ACs still possessed the ability to mobilize uranium in vivo even if administration was delayed for 72 h.

A review of flocculants as an efficient method for increasing the efficiency of municipal sludge dewatering: Mechanisms, performances, influencing factors and perspectives

Mechanical sludge dewatering is one of the stages of the municipal wastewater treatment process, which allows the amount of generated sludge and the cost of its transport and management to be reduced. Achieving a high degree of dewatering is possible thanks to the use of flocculation technology. The article presents issues related to the theory of flocculation, sewage sludge, and its dewatering. The main mechanisms of flocculation, the kinetics of the process, the division of flocculants, and flocculation in dual systems are discussed. The influence of particular parameters on the efficiency of flocculation and the dewatering of sewage sludge was analyed. The assessed parameters are: pH, the presence of salt, the mixing process, the structure and ionicity of chains, and the dose. The results of experimental studies on the dewatering of various types of sludge were compared. The literature review included in the paper helps to better understand the process of flocculation and sludge dewatering, and presents the progress to date and the possible directions for further development in this field.

Facile synthesis and adsorption characteristics of a hybrid composite based on ethyl acetoacetate modified chitosan/calcium alginate/TiO2 for efficient recovery of Ni(II) from aqueous solution

In this study, chemical modification of chitosan has been carried out using epichlorohydrin as crosslinking agent and ethyl acetoacetate as a modifier to graft acetoacetyl moiety. The said organo-functionalization on chitosan and sodium alginate not only offered a novel support for TiO2 immobilization but also enhanced sorption performance for Ni(II) recovery from aqueous medium. So, a composite consisting of acetoacetyl moiety grafted chitosan, sodium alginate and titanium oxide (EAA-MCS/TiO2) was prepared and characterized by fourier transform-infra red (FT-IR) spectroscopy and scanning electron microscopy (SEM). The hybrid composite (3EAA-MCS/TiO2) which had TiO2 to EAA-MCS mass ratio of 20.0% by weight showed maximum sorption efficiency. The formulated sorbent was conditioned in the form of hydrogel beads for operation. Isothermal sorption and kinetics studies were performed at pH = 6.0 to configure the nature of sorption. Pseudo-2nd order rate expression better explained the sorption kinetics and chemisorption is the predominant mode of uptake. Langmuir adsorption model better explained the sorption process (R 2 ∼ 0.99) and maximum monolayer sorption capacity (q m ) at sorption/desorption dynamic equilibrium was computed as 403 mg/g at optimized pH.

Xanthate-Modified Magnetic Fe3O4@SiO2-Based Polyvinyl Alcohol/Chitosan Composite Material for Efficient Removal of Heavy Metal Ions from Water

Chitosan has several shortcomings that limit its practical application for the adsorption of heavy metals: mechanical instability, a challenging separation and recovery process, and low equilibrium capacity. This study describes the synthesis of a magnetic xanthate-modified polyvinyl alcohol and chitosan composite (XMPC) for the efficient removal and recovery of heavy metal ions from aqueous solutions. The XMPC was synthesized from polyvinyl alcohol, chitosan, and magnetic Fe₃O₄@SiO₂ nanoparticles. The XMPC was characterized, and its adsorption performance in removing heavy metal ions was studied under different experimental conditions. The adsorption kinetics fit a pseudo-second-order kinetic model well. This showed that the adsorption of heavy metal ions by the XMPC is a chemical adsorption and is affected by intra-particle diffusion. The equilibrium adsorption isotherm was well described by the Langmuir and Freundlich equations. The XMPC reached adsorption equilibrium at 303 K after approximately 120 min, and the removal rate of Cd(II) ions was 307 mg/g. The composite material can be reused many times and is easily magnetically separated from the solution. This makes the XMPC a promising candidate for widespread application in sewage treatment systems for the removal of heavy metals.

Waste tea residue adsorption coupled with electrocoagulation for improvement of copper and nickel ions removal from simulated wastewater

The present research involves removing copper and nickel ions from synthesized wastewater by using a simple, cheap, cost-effective, and sustainable activated green waste tea residue (AGWTR) adsorption coupled with electrocoagulation (ADS/EC) process in the presence of iron electrodes. By considering previous studies, their adsorbents used for treating their wastewaters firstly activate them by applying either chemicals or activating agents. However, our adsorbent was prepared without applying neither chemicals nor any activating agents. The operating parameters such as pH, hydraulic retention time, adsorbent dose, initial concentration, current density, and operating cost for both metals were optimized. In ADS/EC, the removal efficiency was obtained as 100% for copper and 99.99% for nickel ions. After the ADS/EC process, Fourier transform infrared (FT-IR) spectroscopy, Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDS) analysis were used to characterize the adsorbent green waste tea residue. The adsorption isotherm and kinetic model results showed that the Langmuir and the pseudo-second-order were well-fitted to the experimental adsorption data better than the Freundlich and pseudo-first-order models for both Cu²⁺ and Ni²⁺ with their maximum adsorption capacity of 15.6 and 15.9 mg g⁻¹, respectively. The above results give an option to recycle the metal-based industrial effluents, tea industry-based wastes, enabling a waste-to-green technique for adsorbing and removing the heavy metals and other pollutants in water.

Chitosan@Carboxymethylcellulose/CuO-Co2O3 Nanoadsorbent as a Super Catalyst for the Removal of Water Pollutants

In this work, an efficient nanocatalyst was developed based on nanoadsorbent beads. Herein, carboxymethyl cellulose–copper oxide-cobalt oxide nanocomposite beads (CMC/CuO-Co2O3) crosslinked by using AlCl3 were successfully prepared. The beads were then coated with chitosan (Cs), Cs@CMC/CuO-Co2O3. The prepared beads, CMC/CuO-Co2O3 and Cs@CMC/CuO-Co2O3, were utilized as adsorbents for heavy metal ions (Ni, Fe, Ag and Zn). By using CMC/CuO-Co2O3 and Cs@CMC/CuO-Co2O3, the distribution coefficients (Kd) for Ni, Fe, Ag and Zn were (41.166 and 6173.6 mLg−1), (136.3 and 1500 mLg−1), (20,739.1 and 1941.1 mLg−1) and (86.9 and 2333.3 mLg−1), respectively. Thus, Ni was highly adsorbed by Cs@CMC/CuO-Co2O3 beads. The metal ion adsorbed on the beads were converted into nanoparticles by treating with reducing agent (NaBH4) and named Ni/Cs@CMC/CuO-Co2O3. Further, the prepared nanoparticles-decorated beads (Ni/Cs@CMC/CuO-Co2O3) were utilized as nanocatalysts for the reduction of organic and inorganic pollutants (4-nitophenol, MO, EY dyes and potassium ferricyanide K3[Fe(CN)6]) in the presence of NaBH4. Among all catalysts, Ni/Cs@CMC/CuO-Co2O3 had the highest catalytic activity toward MO, EY and K3[Fe(CN)6], removing up to 98% in 2.0 min, 90 % in 6.0 min and 91% in 6.0 min, respectively. The reduction rate constants of MO, EY, 4-NP and K3[Fe(CN)6] were 1.06 × 10−1, 4.58 × 10−3, 4.26 × 10−3 and 5.1 × 10−3 s−1, respectively. Additionally, the catalytic activity of the Ni/Cs@CMC/CuO-Co2O3 beads was effectively optimized. The stability and recyclability of the beads were tested up to five times for the catalytic reduction of MO, EY and K3[Fe(CN)6]. It was confirmed that the designed nanocomposite beads are ecofriendly and efficient with high strength and stability as catalysts for the reduction of organic and inorganic pollutants.

Anodic Electrodeposition of Chitosan-AgNP Composites Using In Situ Coordination with Copper Ions

Chitosan is an attractive material for biomedical applications. A novel approach for the anodic electrodeposition of chitosan–AgNP composites using in situ coordination with copper ions is proposed in this work. The surface and cross-section morphology of the obtained coating with varying concentrations of AgNPs were evaluated by SEM, and surface functional groups were analyzed with FT-IR spectroscopy. The mechanism of the formation of the coating based on the chelation of Cu(II) ions with chitosan was discussed. The antibacterial activity of the coatings towards Staphylococcus epidermidis ATCC 35984/RP62A bacteria was analyzed using the live–dead approach. The presented results indicate that the obtained chitosan–AgNP-based films possess some limited anti-biofilm-forming properties and exhibit moderate antibacterial efficiency at high AgNP loads.

Synthesis and characterization of a novel benzothiazole functionalized chitosan and its use for effective adsorption of Cu(II)

Contamination of water with the copper(II) ions leads to serious diseases such as liver damage and cancer. This deadly effect prompted us to target the synthesis of a novel functionalized chitosan (Cs-BT) to be used as an adsorbent for removing the copper(II) ions from the aqueous solution. The functionalization was done by introducing benzothiazole moiety into the chitosan (Cs) chain and confirmed by the full disappearance of the NH₂ band in the FT-IR spectrum of the adsorbent. The TGA-DTG analysis revealed that the functionalization reduced the thermal stability of the adsorbent (Cs-BT) as compared with pure chitosan. The adsorption was evidenced by SEM and EDX analysis. The adsorption study demonstrated that the optimal adsorption conditions were 120 min contact time, pH = 6, and initial Cu(II) concentration 200 mg/L. At these conditions, the Cs-BT achieved a maximum copper adsorption capacity of 1439.7 mg/g. Consequently, Cs-BT could be a promising and efficient Cu adsorbent in water treatment. Study the adsorption kinetics and isotherms manifested that the pseudo-first-order was better than pseudo-second-order and Temkin isotherm was better than Langmuir, Freundlich, and Dubinin-Radushkevich for explaining the adsorption process. The calculated thermodynamic parameters implied the spontaneity and the endothermic nature of the adsorption process.

Influence of Selective Conditions on Various Composite Sorbents for Enhanced Removal of Copper (II) Ions from Aqueous Environments

Numerous pollutants, including dyes, heavy metals, pesticides, and microorganisms, are found in wastewater and have great consequences when discharged onto natural freshwater sources. Heavy metals are predominantly reported in wastewater. Heavy metals are persistent, non-biodegradable and toxic, transforming from a less toxic form to more toxic forms in environmental media under favourable conditions. Among heavy metals, copper is dominantly found in wastewater effluent. In this review, the effects of high concentration of copper in plants and living tissues of both aquatic animals and humans are identified. The performance of different polymer adsorbents and the established optimum conditions to assess the resultant remediation effect as well as the amount of copper removed are presented. This procedure allows the establishment of a valid conclusion of reduced time and improved Cu (II) ion removal in association with recent nano-polymer adsorbents. Nano-polymer composites are therefore seen as good candidates for remediation of Cu ions while pH range 5-6 and room temperature were mostly reported for optimum performance. The optimum conditions reported can be applied for other metal remediation and development of potent novel adsorbents and process conditions.

Column and batch sorption investigations of nickel(II) on extractant-impregnated resin

Macroporous resin-supported reagents have been identified as potential adsorbents for removal of toxic pollutants. This article presents an experimental designed to evaluate the sorption and desorption of nickel(II) with the help of column and batch procedure using simple extractant-impregnated resin (EIR). Isonitroso-4-methyl-2-pentanone (IMP) as an extractant was impregnated on a solid support like Amberlite XAD-4 to prepare the EIR sorbent. Column experimental conditions such as pH, sample flow rate and volume, eluting solution, and interfering ions were studied to optimize the nickel(II) sorption and recovery from aqueous media. The column results suggest that the quantitative nickel(II) sorption was observed at pH 5-6, and the quantitative recovery (≥ 95%) was achieved by using 1.0 M HNO₃. The high concentrations of cations and anions (except EDTA) present in the spiked binary and multi-element mixture solution show no interferences in both quantitative sorption and recovery of nickel(II), whereas the batch experiments were performed to evaluate nickel(II) sorption behavior using the linearized and non-linearized kinetic and isotherm models. By error function analysis, the Freundlich isotherm and the pseudo-first-order kinetic model were found to describe best the experimental data obtained over the studied concentration range and sorption time, respectively. The maximum sorption capacity of nickel(II) onto the EIR sorbent was found to be ~ 81 mg/g. The mean free energy (E = 10.1 kJ/mol) determined using Dubinin-Radushkevich isotherm suggests chemical nature of nickel(II) sorption on EIR. The novelty of the EIR adsorbent lies in its potential for separation and recovery of nickel(II) at trace level in water samples of different origin.

Removal of the heavy metal ion nickel (II) via an adsorption method using flower globular magnesium hydroxide

To remove toxic Ni(II) ions from wastewater, a novel flower globular magnesium hydroxide (FGMH) was prepared by a gentle method using trisodium citrate as a crystal modifier. This material exhibited a high specific surface area. The synthesized products and adsorption mechanism for Ni(II) ions were examined by diverse characterization technologies and methods. FGMH was employed to remove Ni(II) ions by the adsorption method. The effects of various parameters, viz., the amount of adsorbent, contact time, temperature and pH, on the removal rate by the adsorbent were investigated in detail. The kinetic data fitted well with a pseudo-second-order model and experimental equilibrium adsorption data conformed to a Langmuir isotherm under optimized conditions. The optimal process parameters included 30 mg of FGMH, a 50 min contact time, pH values between 6.07 and 7.71 for the Ni(II) solution, and adsorption at room temperature for 50 mL of 80 mg/L Ni(II) solution. The percentage of removal efficiency was found to be above 92.64%, and the maximum adsorption capacity of MH was 287.11 mg/g under optimum adsorption conditions. The analyses indicated that the Ni(II) ions were chemisorbed on the FGMH surface.