Effect of immobilization on the activity of catalase carried by poly(HEMA-GMA) cryogels

β-Lactoglobulin-based aerogels: Facile preparation and sustainable removal of organic contaminants from water

Economically and efficiently removing organic pollutants from water is still a challenge in wastewater treatment. Utilizing environmentally friendly and readily available protein-based natural polymers to develop aerogels with effective removal performance and sustainable regeneration capability is a promising strategy for adsorbent design. Here, a robust and cost-effective method using inexpensive β-lactoglobulin (BLG) as raw material was proposed to fabricate BLG-based aerogels. Firstly, photocurable BLG-based polymers were synthesized by grafting glycidyl methacrylate. Then, a cross-linking reaction, including photo-crosslinking and salting-out treatment, was applied to prepared BLG-based hydrogels. Finally, the BLG-based aerogels with high porosity and ultralight weight were obtained after freeze-drying. The outcomes revealed that the biocompatible BLG-based aerogels exhibited effective removal performance for a variety of organic pollutants under perfectly quiescent conditions, and could be regenerated and reused many times via a simple and rapid process of acid washing and centrifugation. Overall, this work not only demonstrates that BLG-based aerogels are promising adsorbents for water purification but also provides a potential way for the sustainable utilization of BLG.

Co-Immobilization of a Multi-Enzyme Cascade: (S)-Selective Amine Transaminases, l-Amino Acid Oxidase and Catalase

An enzyme cascade was established previously consisting of a recycling system with an l-amino acid oxidase (hcLAAO4) and a catalase (hCAT) for different α-keto acid co-substrates of (S)-selective amine transaminases (ATAs) in kinetic resolutions of racemic amines. Only 1 mol % of the co-substrate was required and l-amino acids instead of α-keto acids could be applied. However, soluble enzymes cannot be reused easily. Immobilization of hcLAAO4, hCAT and the (S)-selective ATA from Vibrio fluvialis (ATA-Vfl) was addressed here. Immobilization of the enzymes together rather than on separate beads showed higher reaction rates most likely due to fast co-substrate channeling between ATA-Vfl and hcLAAO4 due to their close proximity. Co-immobilization allowed further reduction of the co-substrate amount to 0.1 mol % most likely due to a more efficient H2 O2 -removal caused by the stabilized hCAT and its proximity to hcLAAO4. Finally, the co-immobilized enzyme cascade was reused in 3 cycles of preparative kinetic resolutions to produce (R)-1-PEA with high enantiomeric purity (97.3 %ee). Further recycling was inefficient due to the instability of ATA-Vfl, while hcLAAO4 and hCAT revealed high stability. An engineered ATA-Vfl-8M was used in the co-immobilized enzyme cascade to produce (R)-1-(3-ethoxy-4-methoxyphenyl)-2-(methylsulfonyl)ethanamine, an apremilast-intermediate, with a 1,000 fold lower input of the co-substrate.

Glutaraldehyde-pea protein grafted polysaccharide matrices for functioning as covalent immobilizers

Three polysaccharide matrices (κ-Carrageenan (Carr), gellan gum, and agar) were grafted via glutaraldehyde (GA) and pea protein (PP). The grafted matrices covalently immobilized β-D-galactosidase (β-GL). Nonetheless, grafted Carr acquired the topmost amount of immobilized β-GL (iβ-GL). Thus, its grafting process was honed via Box-Behnken design and was further characterized via FTIR, EDX, and SEM. The optimal GA-PP-Carr grafting comprised processing Carr beads with 10% PP dispersion of pH 1 and 25% GA solution. The optimal GA-PP-Carr beads acquired 11.44 Ug^-1 iβ-GL with 45.49% immobilization efficiency. Both free and GA-PP-Carr iβ-GLs manifested their topmost activity at the selfsame temperature and pH. Nonetheless, the β-GL K_m and V_max values were reduced following immobilization. The GA-PP-Carr iβ-GL manifested good operational stability. Moreover, its storage stability was incremented where 91.74% activity was offered after 35 storage days. The GA-PP-Carr iβ-GL was utilized to degrade lactose in whey permeate with 81.90% lactose degradation efficiency.

Room-Temperature Self-Healable Blends of Waterborne Polyurethanes with 2-Hydroxyethyl Methacrylate-Based Polymers

The design of self-healing agents is a topic of important scientific interest for the development of high-performance materials for coating applications. Herein, two series of copolymers of 2-hydroxyethyl methacrylate (HEMA) with either the hydrophilic N,N-dimethylacrylamide (DMAM) or the epoxy group-bearing hydrophobic glycidyl methacrylate were synthesized and studied as potential self-healing agents of waterborne polyurethanes (WPU). The molar percentage of DMAM or GMA units in the P(HEMA-co-DMAMy) and P(HEMA-co-GMAy) copolymers varies from 0% up to 80%. WPU/polymer composites with a 10% w/w or 20% w/w copolymer content were prepared with the facile method of solution mixing. Thanks to the presence of P(HEMA-co-DMAMy) copolymers, WPU/P(HEMA-co-DMAMy) composite films exhibited surface hydrophilicity (water contact angle studies), and tendency for water uptake (water sorption kinetics studies). In contrast, the surfaces of the WPU/P(HEMA-co-GMAy) composites were less hydrophilic compared with the WPU/P(HEMA-co-DMAMy) ones. The room-temperature, water-mediated self-healing ability of these composites was investigated through addition of water drops on the damaged area. Both copolymer series exhibited healing abilities, with the hydrophilic P(HEMA-co-DMAMy) copolymers being more promising. This green healing procedure, in combination with the simple film fabrication process and simple healing triggering, makes these materials attractive for practical applications.

Biodegradation of environmental pollutants using catalase-based biocatalytic systems

The synergistic combination of biocatalysts and nanomaterials provides a new interface of a robust biocatalytic system that can effectively remediate environmental pollutants. Enzymes, such as catalase-based constructs, impart the desired candidature for catalytic transformation processes and are potential alternatives to replace conventional remediation strategies that have become laborious and somewhat inefficient. Furthermore, the controlled or uncontrolled discharge of various emerging pollutants (EPs) into water bodies is equally proportional to the fast-growing population and extensive urbanization. EPs affect the entire living being and continuously deteriorate the environmental system, directly or indirectly. The occurrence of EPs (even released after partial treatments, but still in bioactive forms) disturbs ecological integrity. Due to the ineffectiveness of in-practice traditional remediation processes, new and robust treatment measures as effective and sustainable remediation have become a meaningful goal. In this context, special attention has been shifted to engineering an enzyme (catalase)-based biodegradation system with immense prospects in environmental cleanup. The unique synergistic combination of nanomaterials (having multifunctional attributes) with enzymes of interest makes them a state-of-the-art interface that can further ameliorate bio-catalysis and biodegradation performance. This review covers current research and scientific advancement in developing and deploying catalase-based biocatalytic systems to mitigate several EPs from the environment matrices. The biocatalytic features of catalase, along with the mechanistic insight into H₂O₂ neutralization, several nano-based materials loaded with catalase, including nanoparticles (NPs), carbon nanotubes (CNTs), metal-organic frameworks (MOFs), polymeric-based composites, oxime-functionalized cryo-gel disks, electro-spun nanofibrous membranes, and other hybrid materials have also been discussed with suitable examples.

Synthesis and Characterization of a New Cryogel Matrix for Covalent Immobilization of Catalase

The advantages of cryogels for enzyme immobilization applications include their mechanical and chemical robustness, ease of production, superior porosity, and low cost. Currently, many researchers are exploring porous material-based systems for enzyme immobilization that are more efficient and economically viable. Here, poly(2-Hydroxyethyl methacrylate-co-allyl glycidyl ether) (p(HEMA-co-AGE)) cryogel matrices were synthesized via the free radical cryopolymerization method to be employed as the support material. For the immobilization of the catalase enzyme onto the p(HEMA-co-AGE) cryogel matrix (catalase@p(HEMA-co-AGE), the best possible reaction conditions were determined by altering parameters such as pH, catalase initial concentration, and flow rate. The maximum catalase immobilization amount onto the p(HEMA-co-AGE) cryogel was found to be 48 mg/g cryogel. To determine the advantages of the cryogel matrix, e.g., the stability and reusability of the cryogel matrix, the adsorption–desorption cycles for the catalase enzyme were repeated five times using the same cryogel matrix. At the end of the reusability tests, it was found that the cryogel was very stable and maintained its adsorption capacity with the recovery ratio of 93.8 ± 1.2%. Therefore, the p(HEMA-co-AGE) cryogel matrix affords repeated useability, e.g., up to five times, without decreasing its catalase binding capacities significantly and has promising potential for many industrial applications. Cryogels offer clear distinctive advantages over common materials, e.g., micro/nano particles, hydrogels, films, and composites for these applications. At present, many researchers are working on the design of more effective and economically feasible, porous material-based systems for enzyme immobilization

Invertase adsorption with polymers functionalized by aspartic acid

Today, the separation and purification processes are highly preferred over the affinity interactions in the scientific world. Among the materials used for this purpose, magnetic particles and cryogels are very popular. Both polymeric structures have their advantages and disadvantages. In this study, poly(2-Hydroxyethyl methacrylate-N-methacryloyl-L-aspartic acid), poly(HEMA-MAsp), magnetic microparticles, and cryogels were synthesized, and adsorption performances of both polymeric structures were investigated by using invertase from aqueous systems. Invertase (β-fructofuranoside fructohydrolase, EC 3.2.1.26) is a commercially important enzyme used in the food industry to obtain the product called invert sugar, which consists of a mixture of equivalent amounts of glucose and fructose. Therefore, it was preferred as a model enzyme in adsorption studies of polymeric structures. According to the results, 104.1 mg g−1 and 135.5 mg g−1 of adsorption capacity values were obtained for cryogel and magnetic microparticle forms, respectively. Increasing temperature slightly reduced the adsorption capacity of both polymeric structures. In the adsorption/desorption cycle studies performed five times with poly(HEMA-MAsp) polymers, both forms were found to have high reusable properties. It was determined that the activity of invertase immobilized on polymeric structures was preserved at a rate of 83.6% for the particle form and 89.2% for the cryogel form.

Catalase-integrated metal-organic framework with synergetic catalytic activity for colorimetric sensing

As a platform for enzyme immobilization, metal-organic frameworks (MOFs) can protect enzyme activity from the interference of external adverse environment. Although these strategies have been proven to produce good results, little consideration has been given to the functional similarity of MOFs to the encapsulated enzyme. Here, catalase (CAT) was encapsulated in Fe-BTC with peroxidase-like activity to obtain a stable composite (CAT@Fe-BTC) with synergistic catalytic activity. Depending on the superior selectivity and high catalytic activity of CAT@Fe-BTC, colorimetric sensing for the detection of hydrogen peroxide and phenol was developed. This work demonstrates that the integration of functional MOFs with natural enzyme can be well applied to the construction of efficient catalysts.

Laccase bound to cryogel functionalized with phenylalanine for the decolorization of textile dyes

In this study, amino acid functionalized poly(2-hydroxyethyl methacrylate-N-methacrylolyl-l-phenylalanine) [PHEMAPA] cryogel discs were prepared. In this respect, phenylalanine containing N-methacryloyl-(L)-phenylalanine methyl ester (MAPA) was polymerized with 2-hydroxyethyl methacrylate (HEMA) without requirement of any activation step. Laccase bound poly(2-hydroxyethyl methacrylate-N-methacryloyl-l-phenylalanine) [Lac-PHEMAPA] cryogel discs were applied for decolorization of Reactive Blue-247 (RB-247). The ability of Lac-PHEMAPA cryogel discs on dye decolorization was found to be as 90% in 2 h and even more within 4h. The decolorization activities of 86% and 73% were observed at relatively low (4°C) and high (60°C) temperatures, respectively. The effect of dye concentration on dye decolorization and 100% decolorization activity was achieved in dye concentration between 50-300 ppm. Lac-PHEMAPA cryogel discs maintained 80% of its decolorization activity after six cycles. Consequently, the PHEMAPA cryogel discs are promising materials for immobilizing laccase. The Lac-PHEMAPA has a rapid dye decolorization in a broad range of temperature. The preparation is furthermore very stable and activity is preserved during storage.

Grafted carrageenan: alginate gel beads for catalase enzyme covalent immobilization

A new matrix formulation was devised for catalase immobilization. Carrageenan-alginate beads different ratios were developed and soaked into different ratios of CaCl₂-KCl as a hardening solution. The best formulation for loading capacity was selected, treated with polyethylene imine followed by glutaraldehyde and further studied. The best concentration of catalase for immobilization was 300U/ml and the best loading time was 6 h. The catalytic properties increased after immobilization and the immobilized catalase achieved optimum activity at a temperature range of 30-50 °C that was compared to the optimum activity of free catalase which occurred at 40 °C. Higher catalytic activity of immobilized catalase occurred at alkaline pHs than the free one which achieved optimum catalytic activity at neutral pH. A comparison between the kinetic parameters of immobilized and free catalase showed variation. The K _M and Vmax of the immobilized catalase were 2.4 fold and six times higher than those of free catalase. The results of the study indicate that the formulated matrix can be used as a good matrix for catalase enzyme in various industrial applications.

Water-soluble polymeric particle embedded cryogels: Synthesis, characterisation and adsorption of haemoglobin

Making cryogels, which are among today’s accepted adsorbents, more functional with different methods, has been one of the subjects spent overtime. In this study, water-soluble poly(maleic anhydride-alt-acrylic acid) polymer embedded in poly(2-hydroxyethyl methacrylate) cryogels. Copper ions were then immobilised to this structure, and this polymer was used for adsorption of haemoglobin from aqueous systems. Adsorption interaction was carried out on an electrostatic basis, and approximately 448.62 mg haemoglobin/g polymer adsorption capacity value was obtained. It was found that the same material has managed to maintain its adsorption ability by 90.3% even after the use of it five times in the adsorption/desorption cycle. The adsorption interaction was determined to be appropriate for the Langmuir model by isotherm studies. The change in Gibbs free energy value was calculated as −2.168 kJ/mol.

Cibacron blue F3GA incorporated immobilized metal chelate affinity sorbent as a high efficient affinity immobilization materials for catalase enzyme

Catalase is a metalloenzyme commonly found in almost all plant and animal tissues and catalyzes the conversion of hydrogen peroxide to less reactive molecules. It is used for the elimination of hydrogen peroxide in biological, biomedical, food and textile applications. For this purpose, a novel affinity sorbent [poly(methacrylic acid- N-isopropyl acrylamide-CB-Fe³⁺, (p(MAA-NIPAAM)-CB-Fe³⁺)] for the determination and it was first developed using MAA and NIPAAM monomers. After characterization with Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), X-ray Photoelectron Spectroscopy (XPS), adsorption parameters were determined. Reusability of p(MAA-NIPAAM)-CB-Fe³⁺ sorbent was determined after by determining the appropriate desorption agent for desorption of adsorbed catalase in the developed sorbent. It was determined that catalase adsorption could be performed with 0.01 g of sorbent in 45 min. The maximum adsorption capacity for catalase adsorption was determined as 243.17 mg/g with the use of sorbent. The operational and storage stability of the immobilized catalase was found to be high as expected. The conversion of H₂O₂ can be successfully performed by the immobilized enzyme in the prepared sorbent. It has been proven that the affinity of catalase for its substrate is increased by immobilization.

Reducing lactose content of milk from livestock and humans via lactose imprinted poly(2-hydroxyethyl methacrylate-N-methacryloyl-i-aspartic acid) cryogels

Lactase, which can cause lactose intolerance in its deficiency, is a vital enzyme concerning digestion. To overcome lactose intolerance for patients with digestion problem depending of this kind of issue, lactose in food should be removed. In this study, lactose imprinted poly(2-hydroxyethyl methacrylate-N-methacryloyl-l-aspartic acid), poly(HEMA-MAsp), cryogels were synthesized to reduce the amount of lactose content of milk samples. Occurrence of desired bounds, structural integrity, and surface characteristics were analyzed via Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance (NMR), scanning electron microscope (SEM), micro computed tomography (CT), and confocal microscope methods. Water retention characteristic were tested in solution with different electrolytic nature. Adsorption parameters were optimized in an aqueous medium. The adsorption performance of imprinted cryogels was studied in milk samples obtained from cow, sheep, goat, buffalo, and from human volunteers at different intervals after birth. Amount of lactose adsorbed in aqueous media and milk sample from humans were 322 (56.7%) and 179.5 (5.94%) mg lactose/g polymer, respectively. Selectivity studies revealed an approximately 8-fold increase in adsorption rate of molecularly imprinted cryogels as compared to that of nonimprinted cryogels. In addition, competitive adsorption was conducted using lactose-imprinted cryogels in aqueous media containing lactose, glucose, and galactose molecules resulting in adsorption rates of 220.56, 57.87, and 61.65 mg biomolecule/g polymer, respectively.

Facile synthesis of catalase@ZIF-8 composite by biomimetic mineralization for efficient biocatalysis

Enzymes immobilized in metal-organic frameworks (MOFs) have attracted great attention as a promising hybrid material. In the study, a novel biomimetic mineralization encapsulation process for a highly stable and easily reusable catalase (CAT)@ZIF-8 composite has been designed. This immobilization process provides a high enzyme loading of 70 wt %. The CAT@ZIF-8 composites exhibited a much lower K_m value and better enzyme activity than those of free CAT, exhibiting good stability against enzymatic hydrolysis and protein denaturation under harsh conditions. The inhibitory effects of pesticides such as pH, temperature, solvent (i.e., methanol, dimethyl sulfoxide and tetrahydrofuran) and storage at room temperature (6 months) on the activity of free and immobilized catalase enzyme were investigated. The CAT@MOF composites also exhibited excellent reusability, an obvious advantage for treating a wastewater from food processing. The CAT@MOF developed is promising for the efficient removal of H₂O₂ under harsh conditions.

Antimicrobial magnetic poly(GMA) microparticles: synthesis, characterization and lysozyme immobilization

Micron-sized magnetic particles currently find a wide range of applications in many areas including biotechnology, biochemistry, colloid sciences and medicine. In this study, magnetic poly(glycidyl methacrylate) microparticles were synthesized by providing a polymerization around Fe(II)-Ni(II) magnetic double salt. Adsorption of lysozyme protein from aqueous systems was studied with these particles. Adsorption studies were performed with changing pH values, variable amount of adsorbent, different interaction times and lysozyme amounts. The adsorption capacity of the particles was investigated, and a value of about 95.6 mg lysozyme/g microparticle was obtained. The enzyme activity of the immobilized lysozyme was examined and found to be more stable and reusable compared to the free enzyme. The immobilized enzyme still showed 80% activity after five runs and managed to maintain 78% of its initial activity at the end of 60 days. Besides, in the antimicrobial analysis study for six different microorganisms, the minimum inhibitory concentration value of lysozyme immobilized particles was calculated as 125 μg/mL like free lysozyme. Finally, the adsorption interaction was found to be compatible with the Langmuir isotherm model. Accordingly, it can be said that magnetic poly(GMA) microparticles are suitable materials for lysozyme immobilization and immobilized lysozyme can be used in biotechnological studies.

Solid Lipid Microparticles for Oral Delivery of Catalase: Focus on the Protein Structural Integrity and Gastric Protection

Protein inactivation either during the production process or along the gastrointestinal tract is the major problem associated with the development of oral delivery systems for biological drugs. This work presents an evaluation of the structural integrity and the biological activity of a model protein, catalase, after its encapsulation in glyceryl trimyristate-based solid lipid microparticles (SLMs) obtained by the spray congealing technology. Circular dichroism and fluorescence spectroscopies were used to assess the integrity of catalase released from SLMs. The results confirmed that no conformational change occurred during the production process and both the secondary and tertiary structures were retained. Catalase is highly sensitive to temperature and undergoes denaturation above 60 °C; nevertheless, spray congealing allowed the retention of most biological activity due to the loading of the drug at the solid state, markedly reducing the risk of denaturation. Catalase activity after exposure to simulated gastric conditions (considering both acidic pH and the presence of gastric digestive hydrolases) ranged from 35 to 95% depending on the carrier: increasing of both the fatty acid chain length and the degree of substitution of the glyceride enhanced residual enzyme activity. SLMs allowed the protein release in a simulated intestinal environment and were not cytotoxic against HT29 cells. In conclusion, the encapsulation of proteins into SLMs by spray congealing might be a promising strategy for the formulation of nontoxic and inexpensive oral biotherapeutic products.

Characterization of biocompatible pig skin collagen and application of collagen-based films for enzyme immobilization

Based on the excellent biocompatibility of collagen, collagen was extracted from pig skin by acid-enzymatic method. The films were prepared by the self-aggregation behavior of collagen, and the catalase was immobilized by adsorption, cross-linking and embedding. The experiment investigated the effects of glutaraldehyde on the mechanical properties, external sensory properties, and denaturation temperature of the films. The results showed that self-aggregating material could maintain the triple helix structure of pig skin collagen. The self-aggregation treatment and cross-linking treatment can improve the mechanical properties to 53 MPa, while the glutaraldehyde cross-linking agent can increase the denaturation temperature of the pig skin collagen self-aggregating membrane by 20.35% to 84.48 °C. This means that its application to immobilized catalase has better stability. The comparison shows that the catalase immobilized by the adsorption method has strong activity and high operational stability, and the cross-linking agent glutaraldehyde and the initial enzyme concentration have a significant effect on the immobilization, and the activity can reach 175 U g-1. After 16 uses of the film, the catalase was completely inactivated. This study provides a reference for the preparation of a catalase sensor that can be used to detect hydrogen peroxide in food by a catalase sensor.