Upon designing carboxyl methylcellulose and chitosan-derived nanostructured sorbents for efficient removal of Cd(II) and Cr(VI) from water

Sequestration of Cr (VI) from water using agar-polyvinyl alcohol based cation exchanger

Present study focuses on the use of a biodegradable and cost-effective cation exchanger for removal of Cr (VI) metal ions from water sources. Semi-IPN was prepared through grafting of acrylamide onto agar-polyvinyl alcohol backbone in presence of boric acid and ammonium per sulphate as crosslinker-initiator system. Graft copolymer was converted to cation exchanger through phosphorylation. Characterization was done using methods such as FTIR, SEM-EDX and XRD. Semi-IPN exhibited higher thermal resistance. The findings revealed that the optimum conditions for Cr (VI) removal are pH = 4.0; contact time (min) = 360; adsorbent dose (mg) = 125 and metal ion concentration(mg/L) =2. The adsorption kinetics of Cr (VI) ions are best fit by the pseudo second order kinetic with 0.99 R2 and Kf (rate constant) was found to be 0.97 thereby supporting the Freundlich isotherm. The adsorption isotherm models used in this study were consistent with the Freundlich model, but the pseudo second order model was the most accurate description of the adsorption kinetics. The present investigation showed an excellent potential with 85 % adsorption capacity for the removal of Cr (VI). Moreover, reusability studies showed that the cation exchanger can be used effectively up to four cycles.

A critical review on the separation of heavy metal(loid)s from the contaminated water using various agricultural wastes

Wastewater contamination with heavy metal(loids)s has become a worldwide environmental and public health problem due to their toxic and non-degradable nature. Different methods and technologies have been applied for water/wastewater treatment to mitigate heavy metal(loid)-induced toxicity threat to humans. Among various treatment methods, adsorption is considered the most attractive method because of its high ability and efficiency to remove contaminants from wastewater. Agricultural waste-based adsorbents have gained great attention because of high efficiency to heavy metal(loids)s removal from contaminated water. Chemically modified biosorbents can significantly enhance the stability and adsorption ability of the sorbents. The two mathematical models of sorption, Freundlich and Langmuir isotherm models, have mostly been studied. In kinetic modeling, pseudo-second-order model proved better in most of the studies compared to pseudo-first-order model. The ion exchange and electrostatic attraction are the main mechanisms for adsorption of heavy metal(loid)s on biosorbents. The regeneration has allowed various biosorbents to be recycled and reused up to 4-5 time. Most effective eluents used for regeneration are dilute acids. For practical perspective, biosorbent removal efficiency has been elucidated using various types of wastewater and economic analysis studies. Economic analysis of adsorption process using agricultural waste-based biosorbents proved this approach cheaper compared to traditional commercial adsorbents, such as chemically activated carbon. The review also highlights key research gaps to advance the scope and application of waste peels for the remediation of heavy metal(loid)s-contaminated wastewater.

Studies on adsorption properties of magnetic composite prepared by one-pot method for Cd(II), Pb(II), Hg(II), and As(III): Mechanism and practical application in food

A one-pot synthesis afforded a magnetic, crosslinked polymer adsorbent (m-P6) with a variety of functional groups to realize simultaneous adsorption of Cd2+, Pb2+, Hg2+, and As3+. The material was characterized by TEM-EDS, XRD, FT-IR, VSM, and XPS. Kinetic and isothermal analyses suggested mainly chemisorption processes of heavy metal ions that form multiple layers on heterogeneous surfaces. Theoretical adsorption capacities calculated by a pseudo-2nd-order kinetic model and the Sips isothermal model were 282.88 mg/g for Cd2+, 326.18 mg/g for Pb2+, 117.85 mg/g for Hg2+, and 320.29 mg/g for As3+. m-P6 not only can efficiently adsorb divalent heavy metals (Cd2+, Pb2+, Hg2+), but also demonstrate a process of adsorption-driven catalytic oxidation by single-electron transfer (SET) from As3+ to As5+. In application, in addition to adsorption in water, m-P6 is capable of minimizing matrix interference, and extracting trace heavy metals in a complex environment (cereal) through easy operations for improving the detection accuracy, as well as it is potential for application in detection of trace heavy metals in foodstuffs. m-P6 can be readily regenerated and efficiently recycled for 5 cycles using eluent E12 and dilute acid.

Phytic acid-modified carboxymethyl cellulose hydrogel for uranium adsorption from aqueous solutions

Phytic acid-modified carboxymethyl cellulose (CMC-PA) has been investigated as a promising adsorbent for the removal of uranium from aqueous solutions. The synthesis of CMC-PA involves the hydrogen bonding interaction between CMC and PA, resulting in the incorporation of PA groups onto the cellulose backbone. The hydrophilicity, reusability and adsorption capacity of the prepared CMC-PA hydrogel have improved with the increase of PA content. Moreover, the adsorption experiments were conducted by varying parameters such as pH, initial uranium concentration, and contact time. The results showed that CMC-PA exhibited excellent uranium adsorption performance, with a theoretical maximum adsorption capacity of 436 mg/g. In addition, the material exhibits excellent reusability, and the reusability improves with the increase of crosslinking density, indicating that the crosslinking structure of the polymer gel can effectively enhance the structural stability of the material. Furthermore, CMC-PA also exhibits high selective adsorption performance towards uranium ions in the presence of various competing ions. Its high adsorption capacity, reusability, and selectivity make it a promising candidate for high-performance uranium ion adsorbents.

Magnetic hydrochar grafted-chitosan for enhanced efficient adsorption of malachite green dye from aqueous solutions: Modeling, adsorption behavior, and mechanism analysis

Water pollution by organic dyes is one of the most serious environmental problems worldwide. Malachite green (MG) is considered as one the serious organic dyes which is discharged in wastewater by leather and textile manufacturing plants. MG dye can cause severe hazards to the environment and human health. Therefore, the removal of MG dye from wastewater is very important and essential. This study aims to synthesize a new magnetic hydrochar grafted to chitosan (MWSHC@CS) for the removal of MG dye from the aqueous solutions. Transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area, and Zeta potential analysis were used to characterize the synthesized MWSHC@CS. Batch experiments were conducted to optimize MG dye adsorption conditions, including adsorbent mass, pH, temperature, initial concentration, and contact time. The results revealed that MWSHC@CS had an excellent removal efficiency (96.47 %) for MG dye at the optimum condition (at m: 20 mg, pH: 7.5, t: 420 min, and T: 298 K). Adsorption isotherms outcomes revealed the MG adsorption data were best fit by the Langmuir model with a maximum adsorption capacity (420.02 mg/g). Adsorption kinetics outcomes exhibited that the adsorption process of MG dye fitted well to the Elovich model. The thermodynamic results revealed that the adsorption process was physical, exothermic, and spontaneous. The adsorption mechanisms of MG onto MWSHC@CS were hydrogen bonding, electrostatic interaction, and π-π interactions. Furthermore, MWSHC@CS showed excellent reusability for the removal of MG over five cycles of adsorption-desorption (83.76 %). In conclusion, the study provides a new, low-cost, and effective magnetic nanocomposite based on chitosan as a promising adsorbent for the high-performance removal of MG dye from aqueous solutions.

Visualized adsorption and enhanced photocatalytic removal of Cr6+ by carbon dots-incorporated fluorescent nanocellulose aerogels

In this study, carbon dots (CDs) and titanate nanofibers (TNs) were mixed with TEMPO-oxidized nanocellulose (TOCNC) to prepare fluorescent nanocellulose aerogels (FNAs) by a Schiff base reaction. The resulting FNA can detect the adsorption of Cr6+ through the fluorescence quenching in CDs and promote the removal of Cr6+ through the synergistic effect of CDs in photocatalysis. The optimized FNA has a maximum adsorption capacity of 543.38 mg/g, higher than most reported Cr6+ adsorbents. This excellent performance is due to the porous structure of the aerogel, which gives it a high specific surface area of 20.53 m2/g and provides abundant adsorption sites. Simultaneously, CDs can enhance the amino-induced Cr6+ adsorption, improve the photocatalytic performance of TNs, and expose more adsorption sites through electrostatic adsorption of amino-induced reduction products (Cr3+). This study explores the preparation of visualized nanosorbents with enhanced photocatalytic removal of Cr6+ and provides a new direction for nanoscale photocatalysts.

Machine learning integrated high quantum yield blue light carbon dots for real-time and on-site detection of Cr(VI) in groundwater and drinking water

The safety of groundwater and drinking water is directly related to the well-being of human beings and ecosystems. On-site monitoring and timely response to heavy metals in these water sources are crucial for water supply security. Fluorescent probes combined with machine learning technology have been applied to on-site detection of heavy metals. However, they were primarily focused on industrial-level detection and lacked the sensitivity required for detecting Cr(VI) in groundwater and drinking water. In this study, we developed an machine learning-integrated approach using high-quantum-yield (QY) N-doped blue-light carbon dots (N-BCDs) for instant detection of Cr(VI) in groundwater and drinking water. N-BCDs were synthesized within 3 min using a household microwave oven with citric acid and 1,2-diaminobenzene, resulting in a QY of approximately 90 %. The fluorescence of N-BCDs was quenched via the internal filter effect (IFE), enabling the detection of Cr(VI) within 1 min, with a detection limit of 0.1574 μg L-1 for Cr(VI) concentrations ranging from 0 to 60 μg L-1. We employed machine learning methods to determine Cr(VI) concentrations from simple shots, based on the red-green-blue (RGB) feature and Kmeans feature extraction. These features were input into four models (Ridge, XGB, SVR, and Linear), achieving a fitness of 95.2 %. Furthermore, the accuracies for Cr(VI) concentration identification in actual groundwater and drinking water were as high as 95.71 % and 96.81 %, respectively. Our work successfully extended the detection range of Cr(VI) to the μg level, significantly improving the practical applicability of the method and providing a new approach for on-site detection of Cr(VI) in groundwater and drinking water.

Enhanced removal of methylene blue from wastewater by alginate/carboxymethyl cellulose-melamine sponge composite

Industrial dye wastewater poses a threat to human health due to its harmful effects, and the treatment of related wastewater is receiving increasing attention. In this paper, the melamine sponge with high porosity and convenient separation was selected as matrix material, and alginate/carboxymethyl cellulose-melamine sponge composite (SA/CMC-MeS) was prepared through crosslinking strategy. Not only does the composite cleverly combined the merits of alginate and carboxymethyl cellulose, it also enhanced the adsorption performance for methylene blue (MB). The adsorption data manifested that the adsorption process of SA/CMC-MeS agreed with the Langmuir model and pseudo-second-order kinetic model, and theoretical maximum adsorption capacity was 230 mg/g (pH 8). The characterization results demonstrated that the adsorption mechanism was attributed to the electrostatic attraction between the carboxyl anions on the composite and the dye cations in solution. Importantly, SA/CMC-MeS could selectively separate MB from binary dye system and had positive anti-interference ability in the face of coexisting cations. After 5 times of cycles, the adsorption efficiency remained above 75 %. Based on these outstanding practical properties, this material has a potential to solve dye contamination.

Nanocellulose/carbon dots hydrogel as superior intensifier of ZnO/AgBr nanocomposite with adsorption and photocatalysis synergy for Cr(VI) removal

A novel nanocellulose/carbon dots hydrogel (NCH) was fabricated using cellulose nanofibrils (CN), carbon dots (CD) and zinc oxide (ZnO)/silver bromide (AgBr) nanocomposite, where CD enhanced amino group-induced adsorption of hexavalent chromium (Cr(VI)) and promoted the photocatalytic properties of ZnO/AgBr nanocomposite via the transfer of photogenerated electrons, resulting in enhanced efficiency in the removal of Cr(VI) from aqueous solution. The structure, morphology, and physicochemical properties of the prepared NCH were characterized, with the results of adsorption and photocatalysis experiments showing the maximum theoretical adsorption capacity of the NCH to be 315 mg/g, 219 times that of the ZnO/AgBr nanocomposite; the apparent removal rate constant of the NCH was 0.0319 min^-1, 11.7 times that of the ZnO/AgBr nanocomposite. Furthermore, the removal performance of NCH was attributed to CD-enhanced synergistic adsorption and photocatalysis effects, supported by characterization and experimental results. This work provides insight into the design and fabrication of a novel adsorptive photocatalyst with CD-enhanced synergistic adsorption and photocatalysis effects for removing Cr(VI) from aqueous solution.

Computer chip-inspired design of nanocellulose/carbon dots hydrogel as superior intensifier of nano-sized photocatalyst for effective Cr(VI) removal

Hydrogel, a common carrier of photocatalyst that suffers from compromised catalytic efficiency, is still far from practical application. Herein, based on "computer chip-inspired design", a novel nanocellulose/carbon dots hydrogel (NCH) was fabricated as superior intensifier instead of common carrier of sodium titanate nanofibre (STN), where carbon dots (CDs) enhanced amino group-induced adsorption for Cr(VI), promoted photocatalytic properties of STN via transferring the photogenerated electron-hole pairs and improved amino group-induced desorption for reduced product (Cr(III)) via electrostatic repulsion, showing an efficiency of 1 + 1 > 2. Adsorption and photocatalysis experiments demonstrated superior removal performance of the NCH incorporating STN, as shown by theoretical maximum adsorption capacity of 425.74 mg/g and kinetic constant of 0.0374 min^-1 in the photocatalytic process, which was nearly 6.6 and 7.3 times of STN. A series of experiments was conducted to confirm the novel mechanism of CDs-enhanced adsorption-photocatalysis-desorption synergy. This work not only provides new insights into the fabrication of a superior intensifier for nanosized photocatalyst, but also proposes one new mechanism of CDs-enhanced adsorption-photocatalysis-desorption synergy, which is helpful for designing and optimizing nanosized photocatalyst.

Chitosan grafted tetracarboxylic functionalized magnetic nanoparticles for removal of Pb(II) from an aqueous environment

In this study, the chitosan-grafted tetracarboxylic functionalized magnetic nanoparticle (Fe₃O₄@TCA@CS) was synthesized via in situ co-precipitation process and amidation reaction to improve efficiency of adsorption process and obtain cost-effective adsorbents for removal of toxic Pb(II) metal from aqueous environment. The Fe₃O₄@TCA@CS nanocomposite was analyzed by FTIR, TEM-EDX, TGA, XRD, BET, and Zeta potential. The performance of Fe₃O₄@TCA@CS for Pb(II) ions adsorption was achieved as a function of pH, dose, contact time, initial Pb(II) concentration, and temperature. The influence of coexisting ions such as Na⁺, Ca²⁺, Mg²⁺, and Cd²⁺on removal efficiency of Pb(II) was also investigated. The results revealed that the coexisting ions had little influence on Pb(II) removal efficiency. The pseudo-first-order and Freundlich models were better to describe the adsorption of Pb(II) onto Fe₃O₄@TCA@CS and the maximum adsorption capacity of Pb(II) was 204.92 mg/g at pH:5.5; adsorbent dose: 0.015 g; and temperature: 298 K. Thermodynamic studies revealed that the Pb(II) adsorption onto Fe₃O₄@TCA@CS was an exothermic process. In conclusion, the study provides a new, simple, low-cost, and effective chitosan-based magnetic nanocomposite as a promising adsorbent with excellent adsorption capacity, magnetic separation, and reusability for Pb(II) removal from an aqueous environment.

Research progress in the removal of heavy metals by modified chitosan

Chitosan and its modifiers have been widely studied for their good biocompatibility and excellent adsorption properties for heavy metal ions. The synthesis and application of modified chitosan, the effects of process variables (such as pH, amount of adsorbent, temperature, contact time, etc.), adsorption kinetics, thermodynamics and the adsorption mechanism on the removal of heavy metal ions are reviewed. The purpose is to provide the latest information about chitosan as adsorbent and to promote the synthesis of modified chitosan and its application in the removal of heavy metals.

Construction of nickel ferrite nanoparticle-loaded on carboxymethyl cellulose-derived porous carbon for efficient pseudocapacitive energy storage

The preparation of biomass-derived carbon electrode materials with abundant active sites is suitable for development of energy-storage systems with high energy and power densities. Herein, a hybrid material consisting of highly-dispersed nickel ferrite nanoparticle on 3D hierarchical carboxymethyl cellulose-derived porous carbon (NiFe₂O₄/CPC) was prepared by simple annealing treatment. The synergistic effects of NiFe₂O₄ species with multiple oxidation states and 3D porous carbon with a large specific surface area offered abundant active centers, fast electron/ion transport, and robust structural stability, thereby showing the excellent performance of the electrochemical capacitor. The best performing sample (NiFe₂O₄/CPC-800) exhibited a superior capacitance of 2894F g^-1 at a current density of 0.5 A g^-1. Encouragingly, an asymmetric supercapacitor with NiFe₂O₄/CPC-800 as a positive electrode and activated carbon as a negative electrode delivered a high energy density of 135.2 W h kg^-1 along with an improved power density of 10.04 kW kg^-1. Meanwhile, the superior cycling stability of 90.2% over 10,000 cycles at 5 A g^-1 was achieved. Overall, the presented work offers a guideline for the design and preparation of advanced electrode materials for energy-storage systems.

Effective Adsorption and Sensitive Detection of Cr(VI) by Chitosan/Cellulose Nanocrystals Grafted with Carbon Dots Composite Hydrogel

Due to its lethal effect on the human body and other creatures, Cr(VI) ions have attained widespread public attention, and an effective adsorbent for removing Cr(VI) ions is vital. Chitosan (CS)/cellulose nanocrystals grafted with carbon dots (CNCD) composite hydrogel with strong sorption ability and sensitive detection ability for Cr(VI) was formed. The cellulose nanocrystals (CN) offered a natural skeleton for assembling 3D porous structures, and then improved the sorption ability for Cr(VI); moreover, carbon dots (CD) acted as a fluorescent probe for Cr(VI) and provided Cr(VI) adsorption sites. With a maximum adsorption capacity of 217.8 mg/g, the CS/CNCD composite hydrogel exhibited efficient adsorption properties. Meanwhile, with a detection limit of 0.04 μg/L, this hydrogel was used for selective and quantitative detection of Cr(VI). The determination of Cr(VI) was based on the inner filter effect (IFE) and static quenching. This hydrogel retained its effective adsorption ability even after four repeated regenerations. Furthermore, the economic feasibility of the CS/CNCD composite hydrogel over activated carbon was confirmed using cost analysis. This study provided one new method for producing low-cost adsorbents with effective sorption and sensitive detection for Cr(VI).

Facile transformation of carboxymethyl cellulose beads into hollow composites for dye adsorption

Novel millimeter hollow microspheres were fabricated from carboxymethyl cellulose microspheres and polyethyleneimine using glutaraldehyde as a crosslinking agent. The hollow microspheres prepared with different polyethyleneimine usages and different polyethyleneimine treatment time were investigated deeply and characterized via SEM-EDX, FT-IR, and BET surface area analysis. It was shown that polyethyleneimine could break the coordination bonds between the carboxyl and Al (III) in carboxymethyl cellulose microspheres, leading to the formation of hollow structures. Most importantly, the usage and treatment time of polyethyleneimine can distinctly tailor the structure of the carboxymethyl cellulose microspheres, resulting in the formation of different hollow microspheres with varied shell thickness and size. Most importantly, we found that the prepared hollow microspheres have excellent adsorption performance toward targeted methyl blue under testing conditions. By virtue of the large accessible amount of -NH₂ groups and its unique hollow structure, this type of millimeter hollow microspheres have broad application prospects in the treatment of emerging contaminants in wastewater.

Bi-layered hollow amphoteric composites: Rational construction and ultra-efficient sorption performance for anionic Cr(VI) and cationic Cu(II) ions

Here, we have developed a novel bilayer hollow amphiphilic biosorbent (BHAB-3) with large adsorption capacity, rapid adsorption kinetics, and cost-effective for the removal of Cr(VI) and Cu(II) from aqueous solutions. The synthesis was based on the clever use of freeze-drying to fix the structure, secondary modification of the carboxymethyl cellulose microspheres with polyethyleneimine and cross-linking by glutaraldehyde. The consequences of pH, initial concentration, contact time and temperature on adsorption were investigated. The Langmuir model fits showed that the maximum adsorption capacities of the two target heavy metal ions reached 835.91 and 294.79 mg/g, respectively. Moreover, BHAB-3 was characterized by SEM, FT-IR, TGA, and XPS synergistically, showing that it exhibits a strong complexation ability for Cu(II) and a strong electrostatic effect for Cr(VI). Adsorption and desorption experiments showed only a slight decrease in the adsorption capacity of the BHAB-3 for Cr(VI) and Cu(II) ions after 5 and 26 cycles, respectively. Given the excellent properties of this adsorbent, it is a promising candidate for heavy metal ion removal.

Carboxymethyl cellulose-based cryogels for efficient heavy metal capture: Aluminum-mediated assembly process and sorption mechanism

Heavy metal ions pollution is a terrible issue that needs to be efficiently treated as a matter of priority to construct our sustainable society. However, the easy-to-handling of high-performance biomass-derived sorbents with fascinating features like high sorption capacity, favorable separation and recycling remain challenging. Herein, the development of a novel bead-like adsorbent with above features, that is, Al(III)-assembled carboxymethyl cellulose beads were used for the removal of Pb(II), Ni(II) and Co(II) from aqueous solution. Characterization methods like FT-IR, SEM, XPS and TGA were employed to confirm its physicochemical properties. Removal of the three heavy metal ions at different pH values, initial concentration and contact time were discussed at batch adsorption experiments. Meanwhile, regeneration was also discussed deeply. The results revealed that the adsorption capacity of the sorbents for three heavy metals increases with increasing pH and the initial concentration. The adsorption isotherm could be described well by the Freundlich model, and the maximum adsorption capacity for Pb(II), Ni(II) and Co(II) were 550, 620 and 760 mg/g, respectively. Kinetics study indicated that the Pseudo-second-order model described the best correlation with experimental data, this suggested that the complexation may participated in the adsorption process. More significantly, this type of bead-like adsorbents displayed excellent reusability after four sequential cycles.

Microwave-Assisted Rapid Synthesis of Reduced Graphene Oxide-Based Gum Tragacanth Hydrogel Nanocomposite for Heavy Metal Ions Adsorption

Reduced graphene oxide (RGO) was synthesized in this research via Tour's method for the use of filler in the hydrogel matrix. The copolymerization of N,N-dimethylacrylamide (DMA) onto the gum tragacanth (GT) was carried out to develop gum tragacanth-cl-N,N-dimethylacrylamide (GT-cl-poly(DMA)) hydrogel using N,N'-methylenebisacrylamide (NMBA) and potassium persulfate (KPS) as cross-linker and initiator correspondingly. The various GT-cl-poly(DMA) hydrogel synthesis parameters were optimized to achieve maximum swelling of GT-cl-poly(DMA) hydrogel. The optimized GT-cl-poly(DMA) hydrogel was then filled with RGO to form reduced graphene oxide incorporated gum tragacanth-cl-N,N-dimethylacrylamide (GT-cl-poly(DMA)/RGO) hydrogel composite. The synthesized samples were used for competent adsorption of Hg²⁺ and Cr⁶⁺ ions. Fourier transform infrared, X-ray powder diffraction, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy were used to characterize the gum tragacanth-cl-N,N-dimethylacrylamide hydrogel and reduced graphene oxide incorporated gum tragacanth-cl-N,N-dimethylacrylamide hydrogel composite. The experiments of adsorption-desorption cycles for Hg²⁺ and Cr⁶⁺ ions were carried out to perform the reusability of gum tragacanth-cl-N,N-dimethylacrylamide hydrogel and reduced graphene oxide incorporated gum tragacanth-cl-N,N-dimethylacrylamide hydrogel composite. From these two samples, reduced graphene oxide incorporated gum tragacanth-cl-N,N-dimethylacrylamide exhibited high adsorption ability. The Hg²⁺ and Cr⁶⁺ ions adsorption by gum tragacanth-cl-N,N-dimethylacrylamide and reduced graphene oxide incorporated gum tragacanth-cl-N,N-dimethylacrylamide were best suited for pseudo-second-order kinetics and Langmuir isotherm. The reported maximum Hg²⁺ and Cr⁶⁺ ions adsorption capacities were 666.6 mg g^-1 and 473.9 mg g^-1 respectively.

Poly(3-hydroxybutyrate) Modified by Plasma and TEMPO-Oxidized Celluloses

Microcrystalline cellulose (MCC) was surface modified by two approaches, namely a plasma treatment in liquid using a Y-shaped tube for oxygen flow (MCC-P) and a TEMPO mediated oxidation (MCC-T). Both treatments led to the surface functionalization of cellulose as illustrated by FTIR and XPS results. However, TEMPO oxidation had a much stronger oxidizing effect, leading to a decrease of the thermal stability of MCC by 80 °C. Plasma and TEMPO modified celluloses were incorporated in a poly(3-hydroxybutyrate) (PHB) matrix and they influenced the morphology, thermal, and mechanical properties of the composites (PHB-MCC-P and PHB-MCC-T) differently. However, both treatments were efficient in improving the fiber-polymer interface and the mechanical properties, with an increase of the storage modulus of composites by 184% for PHB-MCC-P and 167% for PHB-MCC-T at room temperature. The highest increase of the mechanical properties was observed in the composite containing plasma modified cellulose although TEMPO oxidation induced a much stronger surface modification of cellulose. This was due to the adverse effect of more advanced degradation in this last case. The results showed that Y-shaped plasma jet oxidation of cellulose water suspensions is a simple and cheap treatment and a promising method of cellulose functionalization for PHB and other biopolymer reinforcements.

Modifying alginate beads using polycarboxyl component for enhanced metal ions removal

Designing desirable adsorbent for highly efficient removal of heavy metal ions is of practical significance, given the cost-effectiveness, environmental benign, natural abundance and easy-handling collection features. Herein, a bead-like adsorbent with high adsorption capacity was prepared by modifying alginate beads using polyacrylate with high density of carboxyl groups. The developed alginate/polyacrylate beads were collaboratively characterized by FT-IR, TGA, SEM, XPS, etc., and various adsorption conditions were tested including the pH of the solution, contact time and the initial concentration. The experimental data were fitted well by the Freundlich isotherm model, and the maximum adsorption capacity was obtained from the Langmuir model was 611.0 mg/g, and adsorption process followed the Pseudo-second-order kinetic model. The adsorption mechanisms conformed to multi-layer adsorption, and mainly dominated by chemical interactions. The bead-like adsorbent exhibited excellent reusability after eight sequential cycles and displayed higher adsorption capacity towards lead ions. This type of adsorbent might possess promising role in treating heavy metals from water by virtue of degradable, cost-effective component and high adsorption efficiency.