HMDSO plasma treatment as alternative to modify structural properties of granular starch

Effect of dielectric barrier discharge (DBD) plasma treatment on physicochemical and 3D printing properties of wheat starch

In recent years, the focus has shifted towards carbohydrate-based hydrogels and their eco-friendly preparation methods. This study involved an investigation into the treatment of wheat starch using dielectric barrier discharge (DBD) plasma technology over varying time gradients (0, 2, 5, 10, 15, and 20 min). The objective was to systematically examine the impact of different treatment durations on the physicochemical properties of wheat starch and the suitability of its gels for 3D printing. Morphology of wheat starch remained intact after DBD treatment. However, it led to a reduction in the amylose content, molecular weight, and crystallinity. This subsequently resulted in a decrease in the pasting temperature and viscosity. Moreover, the gels of the DBD-treated starch exhibited superior 3D printing performance. After a 2-min DBD treatment, the 3D printed samples of the wheat starch gel showed no significant improvements, as broken bars were evident on the surface of the 3D printed graphic, whereas DBD-20 showed better printing accuracy and surface structure, compared to the original starch without slumping. These results suggested that DBD technology holds potential for developing new starch-based gels with impressive 3D printing properties.

Enhancing starch functionality through synergistic modification via sequential treatments with cold plasma and electron beam irradiation

The impact of dual sequential modifications using radio-frequency (RF) plasma and electron beam irradiation (EBI) on starch properties was investigated and compared with single treatments within an irradiation dose range of 5-20 kGy. Regardless of sequence, dual treatments synergistically affected starch properties, increasing acidity, solubility, and paste clarity, while decreasing rheological features with increasing irradiation dose. The molecular weight distribution was also synergistically influenced. Amylopectin distribution broadened particularly below 10 kGy. Amylose narrowed its distribution across all irradiation doses. This was due to dominating EBI-induced degradation and molecular rearrangements from RF plasma. With the highest average radiation-chemical yield (G) and degradation rate constant (k) of (2.12 ± 0.14) × 10-6 mol·J-1 and (3.43 ± 0.23) × 10-4 kGy-1, respectively, upon RF plasma pre-treatment, amylose underwent random chain scission. In comparison to single treatments, dual modification caused minor alterations in spectral characteristics and crystal short-range order structure, along with increased granule aggregation and surface irregularities. The synergistic effect was dose-dependent, significant up to 10 kGy, irrespective of treatment sequence. The highest synergistic ratio was observed when RF plasma preceded irradiation, demonstrating the superior efficiency of plasma pre-treatment in combination with EBI. This synergy has the potential to lower costs and extend starch's technological uses by enhancing radiation sensitivity and reducing the irradiation dose.

Understanding the atmospheric cold plasma-induced modification of finger millet (Eleusine coracana) starch and its related mechanisms

This research was conducted to evaluate the effects of cold plasma (CP) on finger millet starch (FMS). FMS was exposed to partially ionized gas at varying voltages (170, 200, and 230 Volt) for varied time (10, 20, and 30 mins). The impact of treatment was studied using physico-chemical, and functional properties, and the mechanisms of starch modification occurring were stated. A significant reduction in the degree of polymerization was noticed based on parameters like reducing sugar, amylose content, solubility, and molecular weight. However, in certain voltage and time combinations, crosslinking was also confirmed by analysis such as XRD, FTIR, DSC, etc. The properties of starch were altered such as remarkable increase in water solubility by 6.7 times for highest voltage and longest time (230 V/30 min) was registered. NMR data suggested valuable findings- oxidation of OH group at C6 position of starch led to formation of carbonyl group followed by carboxyl group. NMR also showed a decrease in OH protons confirming crosslinking and hence all these analyses helped to conclude findings about the quality changes using CP. It was observed that the highest voltage and considerably longer exposure time of 20 and 30 min induced significant changes in the FMS.

Functionalization Methods of Starch and Its Derivatives: From Old Limitations to New Possibilities

It has long been known that starch as a raw material is of strategic importance for meeting primarily the nutritional needs of people around the world. Year by year, the demand not only for traditional but also for functional food based on starch and its derivatives is growing. Problems with the availability of petrochemical raw materials, as well as environmental problems with the recycling of post-production waste, make non-food industries also increasingly interested in this biopolymer. Its supporters will point out countless advantages such as wide availability, renewability, and biodegradability. Opponents, in turn, will argue that they will not balance the problems with its processing and storage and poor functional properties. Hence, the race to find new methods to improve starch properties towards multifunctionality is still ongoing. For these reasons, in the presented review, referring to the structure and physicochemical properties of starch, attempts were made to highlight not only the current limitations in its processing but also new possibilities. Attention was paid to progress in the non-selective and selective functionalization of starch to obtain materials with the greatest application potential in the food (resistant starch, dextrins, and maltodextrins) and/or in the non-food industries (hydrophobic and oxidized starch).

Evaluation of Loquat Jam Quality at Different Cooking Times Based on Physicochemical Parameters, GC-IMS and Intelligent Senses

The study compared and analyzed the quality of loquat jam with different cooking times through physicochemical parameters, headspace-gas chromatography-ion migration spectroscopy (HS-GC-IMS) and intelligent senses. The results showed that with the prolongation of the cooking time, the color of loquat jam slowly deepened, the energy significantly increased, the adhesiveness, gumminess, hardness and chewiness enhanced, the free amino acid content increased from 22.40 to 65.18 mg/g. The organic acid content increased from 1.64 to 9.82 mg/g. Forty-seven volatile flavor compounds were identified in five types of loquat jam using HS-GC-IMS, among which the relative content of aldehydes was sharply higher than that of other chemical substances, playing an important role in the flavor formation of loquat jam. LJ0, LJ1 and LJ2 had higher aldehyde content, followed by LJ3 and LJ4 had the lowest aldehyde content. The orthogonal partial least squares-discriminant analysis (OPLS-DA) screened 15 marker compounds that could distinguish five types of loquat jam. The E-nose results showed a significant difference in olfactory sense between loquat jam cooked for 100 and 120 min. The E-tongue results corroborated the results of free amino acids (FAAs) and organic acids, indicating that the gustatory sense of loquat jam changed significantly when the cooking time reached 120 min. The results provided a basis for further research on the relationship between the cooking process and quality characteristics of loquat jam.

Synthesis of chitosan-based flocculant by dielectric barrier discharge modification and its flocculation performance in wastewater treatment

As a typical type of organic flocculant, chitosan is limited by its poor water solubility and narrow pH range application. Grafting modification can improve chitosan's solubility and availability through linking macromolecular chains with other types of water-soluble groups or functional side groups. In this study, dielectric barrier discharge (DBD) was used to active the surface of chitosan, then activated chitosan was polymerized with acrylamide to synthesize a chitosan-based flocculant, chitosan-acrylamide (CS-AM). During the synthesis of CS-AM, the optimal conditions were determined as follows: discharge time of 5 min, discharge power of 60 W, total monomer mass concentration of 80 g L-1, polymerization time of 3 h, polymerization temperature of 70 °C, and m(CS) : m(AM) ratio of 1 : 3. The structure and morphological characteristics of CS-AM were investigated and analyzed by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), thermogravimetric (TG) analysis, scanning electron microscopy (SEM), X-ray diffraction (XRD) and N2 physical adsorption, respectively. The removal efficiency of kaolin suspension and CNTs suspension can reach up to 95.9% and 90.2% after flocculation of CS-AM. Furthermore, the zeta potential of the supernatant from the CS-AM treated kaolin suspension at different pH values was examined, and the flocculation mechanism of CS-AM was analyzed. This study provides new ideas for the preparation and development of modified chitosan and broadens its application in water treatment.

Impact of plasma-activated water on the supramolecular structure and functionality of small and large starch granules

Hydrothermal (HMT) and water agitation (WA) treatments using plasma-activated water (PAW) were employed as sustainable methods to modify the molecular and functional performance of small (rice) and large (potato) starch granules. HMT-PAW and WA-PAW treatments resulted in etched and damaged granular surfaces that rearranged the long and short-range crystallinity of the modified starches. Both treatments seemed to predominantly occur in the amorphous region of the rice starch and the crystalline regions of the potato starch, changing the crystallinity values from 22.9 and 14.8 % to 31.8 and 10.4 %, respectively. Thus, the level of the arrangement of chains reached after PAW treatment decreased the ability of rice starch granules to swell (16 to 9 %) and leach out starch molecules from the granules (4.5 to 1.3 %), decreasing the viscosity and pasting profiles as indicated by n and k values. Opposite behavior was observed in the modified potato starches since starch components leached out to a higher extent (1.7 to 5.4 %). The results showed that HMT and WA treatments using PAW are feasible eco-friendly methods for modifying starch granules without chemical reagents. These modified starches could be suitable as functional ingredients or biopolymeric matrices for the food and packaging industry.

Hierarchical structural modification of starch via non-thermal plasma: A state-of-the-art review

The hierarchical architecture of natural and processed starches with different surface and internal structures determines their final physicochemical properties. However, the oriented control of starch structure presents a significant challenge, and non-thermal plasma (cold plasma, CP) has gradually been used to design and tailor starch macromolecules, though without clear illustration. In this review, the multi-scale structure (i.e., chain-length distribution, crystal structure, lamellar structure, and particle surface) of starch is summarized by CP treatment. The plasma type, mode, medium gas and mechanism are also illustrated, as well as their sustainable food applications, such as in food taste, safety, and packaging. The effects of CP on the chain-length distribution, lamellar structure, amorphous zone, and particle surface/core of starch includes irregularity due to the complex of CP types, action modes, and reactive conditions. CP-induced chain breaks lead to short-chain distributions in starch, but this rule is no longer useful when CP is combined with other physical treatments. The degree but not type of starch crystals is indirectly influenced by CP through attacking the amorphous region. Furthermore, the CP-induced surface corrosion and channel disintegration of starch cause changes in functional properties for starch-related applications.

Effects of pin-to-plate atmospheric cold plasma for modification of pearl millet (Pennisetum glaucum) starch

The present study was done to analyze the effect of atmospheric pressure non-thermal pin-to-plate plasma at a range of different voltages (170, 200, and 230V) at different time intervals (10, 20, and 30 mins) on under-utilized pearl millet starch. The untreated and treated starches were analyzed for amylose content, pH, carbonyl, and carboxyl group, reducing sugar, turbidity, water, and oil binding property, pasting property, DSC, FTIR, XRD, and molecular weight. As cold plasma contains highly reactive species and free radicals, it is expected to cause noticeable modifications in the attributes of treated starch. There has been a significant reduction (p < 0.05) in turbidity value by 38.97% and pH value of starch from 6.49 to 4.05. Plasma-treated samples produced clearer pastes with higher stability over storage time. Cold plasma treatment also led to an increase in the ζ potential. However, there has been no significant change in the water activity and oil-binding capacity of the starch. Reducing sugar content, average molecular weight, degree of polymerization, pasting property, XRD, and FTIR data confirmed that cross-linking takes place in samples treated at lower voltages and lesser time followed by depolymerization occurring in harshly treated plasma samples. The study thus points out the possible use of cold plasma for starch modification to produce starches with altered properties.

Plasma Surface Engineering of Natural and Sustainable Polymeric Derivatives and Their Potential Applications

Recently, natural as well as synthetic polymers have been receiving significant attention as candidates to replace non-renewable materials. With the exponential developments in the world each day, the collateral damage to the environment is incessant. Increased demands for reducing pollution and energy consumption are the driving force behind the research related to surface-modified natural fibers (NFs), polymers, and various derivatives of them such as natural-fiber-reinforced polymer composites. Natural fibers have received special attention for industrial applications due to their favorable characteristics, such as low cost, abundance, light weight, and biodegradable nature. Even though NFs offer many potential applications, they still face some challenges in terms of durability, strength, and processing. Many of these have been addressed by various surface modification methodologies and compositing with polymers. Among different surface treatment strategies, low-temperature plasma (LTP) surface treatment has recently received special attention for tailoring surface properties of different materials, including NFs and synthetic polymers, without affecting any of the bulk properties of these materials. Hence, it is very important to get an overview of the latest developments in this field. The present article attempts to give an overview of different materials such as NFs, synthetic polymers, and composites. Special attention was placed on the low-temperature plasma-based surface engineering of these materials for diverse applications, which include but are not limited to environmental remediation, packaging, biomedical devices, and sensor development.

Formation of sweet potato starch nanoparticles by ultrasonic—assisted nanoprecipitation: Effect of cold plasma treatment

Starch nanoparticles (SNPs) were produced from sweet potato starches by ultrasonic treatment combined with rapid nanoprecipitation. The starch concentration, ultrasonic time, and the ratio of starch solution to ethanol were optimized through dynamic light scattering (DLS) technique to obtain SNPs with a Z-average size of 64.51 ± 0.15 nm, poly dispersity index (PDI) of 0.23 ± 0.01. However, after freeze drying, the SNPs showed varying degrees of aggregation depending on the particle size of SNPs before freeze-drying. The smaller the particle size, the more serious the aggregation. Therefore, we tried to treat SNPs with dielectric barrier discharge cold plasma before freeze drying. Properties including morphological features, crystalline structure and apparent viscosity of various starches were measured by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), and rheometer, respectively. The results showed that, after cold plasma (CP) treatment, the aggregation of SNPs during freeze drying was significantly inhibited. Compared to the native sweet potato starch, SNPs showed a higher relative crystallinity and a lower apparent viscosity. After CP treatment, the relative crystallinity of CP SNPs was further higher, and the apparent viscosity was lower. This work provides new ideas for the preparation of SNPs and could promote the development of sweet potato SNPs in the field of active ingredient delivery.

Cold plasma: a promising technology for improving the rheological characteristics of food

At the beginning of the 21st century, many consumers show interest in purchasing safe, healthy, and nutritious foods. The intent requirement of end-users and many food product manufacturers are trying to feature a new processing technique for the healthy food supply. The non-thermal nature of cold plasma treatment is one of the leading breakthrough technologies for several food processing applications. The beneficial response of cold plasma processing on food quality characteristics is widely accepted as a substitution technique for new food manufacturing practices. This review aims to elaborate and offer crispy innovative ideas on cold plasma application in various food processing channels. It highlights the scientific approaches on the principle of generation and mechanism of cold plasma treatment on rheological properties of foods. It provides an overview of the behavior of cold plasma in terms of viscosity, crystallization, gelatinization, shear stress, and shear rate. Research reports highlighted that the cold plasma treated samples demonstrated a pseudoplastic behavior. The published literatures indicated that the cold plasma is a potential technology for modification of native starch to obtain desirable rheological properties. The adaptability and environmentally friendly nature of non-thermal cold plasma processing provide exclusive advantages compared to the traditional processing technique.

Effect of atmospheric pressure non-thermal pin to plate plasma on the functional, rheological, thermal, and morphological properties of mango seed kernel starch

This study aimed to investigate the effect of atmospheric pressure non-thermal pin-to-plate plasma on the functional, rheological, thermal, and morphological properties of mango seed kernel starch. As cold plasma contains highly reactive species and free radicals, it is expected to cause noticeable modifications in the attributes of starch treated. The isolated mango seed kernel starch was subjected to the plasma treatment of input voltages 170 and 230 V for 15 and 30 min of exposure. Water adsorption, swelling, and solubility at lower temperatures. There has been a significant reduction (p < 0.05) in pH values of starch from 7.09 to 6.16 and also the desirable reduction in turbidity values by 42.60%. However, there has been no significant change in the oil and water binding behavior of the starch. The FTIR spectra of MSKS demonstrate the formation of amines which contributes to the better hydrophilic nature of the starch. The structural modification has been adequately confirmed by SEM images. The maximum voltage and time combination, lead to depolymerization of starch which is supported by NMR spectra thus affecting thermal and rheological properties. The application of cold plasma-modified MSKS in food would facilitate stable and smooth textural development.

Nonthermal physical modification of starch: An overview of recent research into structure and property alterations

To tailor the properties and enhance the applicability of starch, various ways of starch modification have been practiced. Among them, physical modification methods (micronization, nonthermal plasma, high-pressure, ultrasonication, pulsed electric field, and γ-irradiation) are highly potential for starch modification considering its safety, environmentally friendliness, and cost-effectiveness, without generating chemical wastes. Thus, this article provides an overview of the recent advances in nonthermal physical modification of starch and summarizes the resulting changes in the multi-level structures and physicochemical properties. While the effect of these techniques highly depends on starch type and treatment condition, they generally lead to the destruction of starch granules, the degradation of molecules, decreases in crystallinity, gelatinization temperatures, and viscosity, increases in solubility and swelling power, and an increase or decrease in digestibility, to different extents. The advantages and shortcomings of these techniques in starch processing are compared, and the knowledge gap in this area is commented on.

Progress in Starch-Based Materials for Food Packaging Applications

The food packaging sector generates large volumes of plastic waste due to the high demand for packaged products with a short shelf-life. Biopolymers such as starch-based materials are a promising alternative to non-renewable resins, offering a sustainable and environmentally friendly food packaging alternative for single-use products. This article provides a chronology of the development of starch-based materials for food packaging. Particular emphasis is placed on the challenges faced in processing these materials using conventional processing techniques for thermoplastics and other emerging techniques such as electrospinning and 3D printing. The improvement of the performance of starch-based materials by blending with other biopolymers, use of micro- and nano-sized reinforcements, and chemical modification of starch is discussed. Finally, an overview of recent developments of these materials in smart food packaging is given.

Understanding the multi-scale structure, physicochemical properties and in vitro digestibility of citrate naked barley starch induced by non-thermal plasma

Non-thermal plasma treatment is an emerging and effective starch modification technique. In this paper, plasma pretreatment was used to modify citrate naked barley starch for enhancing the ability of citric acid to access the starch structure. Plasma treatment did not alter the granule morphology and crystalline type of starch, but degraded the starch molecules and caused more short chains. Plasma pretreatment could etch the starch surface and depolymerize the starch molecules, which increased the accessibility of citric acid for uniform hydrolysis in the subsequent esterification reaction. Therefore, plasma pretreatment significantly promoted the structural and physicochemical modification of the citrate starch, including the enhancement of the degree of substitution, the short-range ordered degree and gelatinization temperatures, and the decreases in the molecular weight, long chains of amylopectin and pasting viscosities. Meanwhile, plasma pretreatment improved the efficiency of acid hydrolysis and decreased the enzymatic digestibility, so that it showed a higher resistant starch content in comparison with its corresponding citrate starch. This paper could provide a new insight into the lower digestion rate and improved functional properties of citrate starch.

Rheological performance of film-forming solutions made from plasma-modified starches with different amylose/amylopectin content

Normal and high amylose corn starches were modified using HMDSO plasma at different time treatments. Changes in functional properties of starch granule, film-forming solutions (FFS) and films were investigated. SEM analysis revealed HMDSO coating deposition on the granule surface, which limited the amylopectin leach out from the granules to the continuous matrix, affecting the rheological properties of the FFS. The amylopectin restriction resulted in a low reinforcement of the network decreasing the viscosity as indicated by n and k values. Also, a gel-like behavior (G' > G″) was observed when the amylose and time treatment increased, suggesting that the matrix becomes less elastic with softer entanglement. This behavior was confirmed by creep test and Burger model parameters. The plasma treatments allowed obtaining FFS with low viscosity, suitable for developing soft and hydrophobic films with low flexibility, as indicated by the decrease of the maximum stress, Hencky strain and permeance values.