Synthetic mechanism of octenyl succinic anhydride modified corn starch based on shells separation pretreatment

Improving resistant starch content of cassava starch by pulsed electric field-assisted esterification

This study aims to investigate the effect of pulsed electric field (PEF) assisted OSA esterification treatment on the multi-scale structure and digestive properties of cassava starch and structure-digestion relationships. The degree of substitution (DS) of starch dually modified at 1.5-4.5 kV/cm was 37.6-55.3 % higher than that of starch modified by the conventional method. Compared with native starch, the resistant starch (RS) content of esterified starch treated with 3 kV/cm significantly increased by 17.13 %, whereas that of starch produced by the conventional method increased by only 5.91 %. Furthermore, assisted esterification at low electric fields (1.5-3 kV/cm) promotes ester carbonyl grafting on the surface of starch granules, increases steric hindrance and promotes the rearrangement of the amorphous regions of starch, which increases the density of the double-helical structure. These structural changes slow down starch digestion and increase the RS content. Therefore, this study presents a potential method for increasing the RS content of starch products using PEF to achieve the desired digestibility.

Investigating the influence of CaCl2 induced surface gelatinization of red adzuki bean starch on its citric acid esterification modification: Structure-property related mechanism

This study prepared starch with different degrees of gelatinization (10 % and 30 %) by CaCl2, and further combined with citric acid at different concentrations (10 %, 20 %, and 30 %) for esterification. The results indicated that CaCl2 induced surface gelatinization and the esterification promoted its fragmentation. This synergistic modification induced depolymerization of starch chains and a decrease in molecular weight, although starch's Maltese cross, growth rings, and crystal type remained unchanged. Moreover, the synergistic modification induces a short-range ordered structure loss and the enthalpy decrease of starch, which induce starch pasting properties decrease and solubility increase. Furthermore, the introduction of ester groups by esterification increases the resistant starch content by limiting the binding sites for digestive enzymes. In conclusion, surface gelatinization can increase active reaction sites by disrupting the starch shell structure, and serves as a potential pretreatment to enhance the deep application of esterified starch in food and pharmaceutical fields.

Structural, physicochemical properties and noodle-making potential of quinoa starch and type 3, type 4, and type 5 quinoa resistant starch

This study prepared type 3, type 4, and type 5 quinoa resistant starch (QRS3, QRS4, and QRS5) from quinoa starch (QS), compared their structural and physicochemical properties and evaluated their noodle-making potential. The results showed that the molecular weight of QRS3 decreased, the number of short-chain molecules increased, and its crystal type changed to B-type after gelatinization, enzymatic hydrolysis, and retrogradation. QRS4 is a phosphorylated cross-linked starch, with a surface morphology, particle size range, and crystal type similar to QS, but displaying modified thermodynamic properties. QRS5 is a complex of amylose and palmitic acid. It displays typical V-type crystals, mainly composed of long chain molecules and primarily exhibits a block morphology. The noodles prepared by replacing 20 % wheat flour with QS, QRS3 and QRS5 have higher hardness and are suitable for people who like elasticity and chewiness. QRS4 noodles are softer and suitable for people like elderly and infants who prefer soft foods. In conclusion, significant differences were evident between the fine structures, crystal types, physicochemical properties and potential applications of QS and the three QRSs. The results may expand the application of QS and QRS in the food and pharmaceutical industries.

Addition of Canna edulis starch and starch nanoparticles to stabilized Pickering emulsions: In vitro digestion and fecal fermentation

Starch nanoparticles (SNPs) were prepared through acid hydrolysis of Canna edulis native starch and modified with octenyl succinic anhydride (OSA) to yield OS-starch and OS-SNPs. These modified particles were used to stabilize curcumin-loaded Pickering emulsions. Effects on gut microbiota during in vitro fecal fermentation were examined. The surface of OS-starch exhibits a porous structure, while OS-SNPs display layered grooves. OSA modification was confirmed by Fourier transform infrared spectroscopy (with peaks at 1728 cm-1 and 1573 cm-1) and proton nuclear magnetic resonance spectra (0.5-2 ppm). The degree of substitution for OS-starch and OS-SNPs is 0.0106 ± 0.0004 and 0.0079 ± 0.0003, respectively. Following modification, the crystallinity decreased from 35.69 ± 0.46 % (native starch) to 30.17 ± 0.70 % (OS-starch), SNPs decreased from 45.87 ± 0.89 % to 43.63 ± 0.64 % (OS-SNPs). Contact angles for OS-starch and OS-SNPs are 77.47 ± 1.78 and 55.57 ± 0.21, respectively. OS-SNPs exhibited superior emulsification properties compared to OS-starch, forming stable Pickering emulsions with pseudoplastic fluid behavior and enhanced curcumin storage protection over 14 days (60.88 ± 4.26 %) with controlled release. Stabilizing Pickering emulsions with OS-starch and OS-SNPs positively affected on gut microbiota and improved the intestinal environment, showing promise for their application in transportation systems and innovative prebiotic food formulations.

Understanding CaCl2 induces surface gelatinization to promote cold plasma modified maize starch: Structure-effect relations

To investigate the influence of surface gelatinization on cold plasma (CP) modification of starch, this study used CaCl2 to modify maize starch by surface gelatinization, further combined with CP treatment and characterized its multi-scale structure and physicochemical properties. The results revealed that starch surface gelatinization causes roughness and fragmentation on the granule surface, and CP undergoes etching effects. The synergistic modification promotes starch degradation, as evidenced by molecular weight decrease and short-chain ratio increase. Although the growth rings, FT-IR patterns, and crystal types of starch remained unchanged, the synergistic modification induced a reduction in the short-range orderliness and crystallinity of starch, thus causing a decrease in the pasting properties and contributing to its solubility. Notably, the CP treatment improved the RDS and SDS contents of the gelatinized starch due to more active sites on the granule surface after gelatinization, and this finding may provide insight into the deep processing of starch.

Digestibility, structural and physicochemical properties of microcrystalline butyrylated pea starch with different degree of substitution

In this study, microcrystalline butyrylated pea starch (MBPS) with higher contents of resistant starch (RS) was synthesized via esterification with butyric anhydride (BA) using microcrystalline pea starch (MPS) as the raw material. With the addition of BA, the new characteristic peaks appeared at 1739 cm^-1 and 0.85 ppm obtained from FTIR and ¹H NMR, respectively, and increased with the higher degree of BA substitution. Moreover, an irregular shape of MBPS, such as condensed particles and more cracks or fragments, had been observed by SEM. Further, the relative crystallinity of MPS increased then native pea starch and decreased with the reaction of esterification. MBPS had higher decomposition onset temperature (T_o) and temperature of maximum decomposition (T_max) with increasing DS values. Simultaneously, an increasing trend RS content from 63.04 % to 94.11 % and a decreasing trends in rapidly digestible starch (RDS) and slowly digestible starch (SDS) contents of MBPS were recorded with increasing DS values. MBPS samples showed higher production capacity of butyric acid ranging from 553.82 μmol/L to 892.64 μmol/L during the fermentation process. Compared with MPS, the functional properties of MBPS were significantly improved.

Structural, rheological, pasting, and digestive properties of wheat A-starch: Effect of outshell removal combined with annealing

Wheat A- starch was subjected to single and combined CaCl₂ and annealing (ANN) treatments. The influence of the treatment on wheat A- starch's structural, rheological, pasting, and digestive characteristics were studied. The results indicated that the application of CaCl₂ treatment caused the removal of the outer layer of wheat A-starch, disrupted the integrity of the growth ring structure, and lowered the molecular weight of amylopectin and relative crystallinity. Meanwhile, the application of outshell removal combined with ANN treatment led to significant damage to the starch granules, resulting in a marked reduction in relative crystallinity, as well as the molecular weight of amylopectin and amylose. However, no changes were found in the non-Newtonian pseudoplastic behavior of starch after single or combined treatments. Furthermore, the combination of outshell removal and annealing treatment resulted in a decreased peak viscosity as well as trough viscosity of starch. Moreover, long-time ANN treatment had the potential to improve the resistant starch (RS) content of deshell starch.

Improving the emulsification performance of adlay seed starch by esterification combined with ultrasonication and enzymatic treatment

In this study, superior modified starch was prepared using ultrasonic and enzymatic treatments to confirm the potential of using adlay seed starch (ASS) in Pickering emulsions. Octenyl succinic anhydride (OSA)-modified starches, such as OSA-UASS, OSA-EASS, and OSA-UEASS, were prepared using ultrasonic, enzymatic, and combined ultrasonic and enzymatic treatments, respectively. The effects of these treatments on the structure and properties of ASS were evaluated to elucidate their influence on starch modification. Ultrasonic and enzymatic treatments improved the esterification efficiency of ASS by changing its external and internal morphological characteristics and the crystalline structure to provide more binding sites for esterification. The degree of substitution (DS) of ASS modified by these pretreatments was 22.3-51.1 % higher than that of the OSA-modified starch without pretreatment (OSA-ASS). Fourier transform infrared and X-ray photoelectron spectroscopy results confirmed the esterification. Small particle size and near-neutral wettability indicated that OSA-UEASS was the promising emulsification stabilizer. The emulsion prepared using OSA-UEASS exhibited better emulsifying activity and emulsion stability and long-term stability for up to 30 days. These amphiphilic granules with improved structure and morphology were used to stabilize a Pickering emulsion.

Effect of shell separation pretreatment on the physicochemical properties of octenyl succinic anhydride-modified starch

The effects of shell separation pretreatment (SSP) on the physicochemical properties of octenyl succinic anhydride (OSA)-modified starch were investigated in this study. SSP at different temperatures promoted esterification between starch molecules and OSA and thereby achieved a higher degree of substitution (DS). OSA-modified granule shells (OSC_s) exhibited a rough surface and irregular shape, which were attributed to swelling caused by SSP during modification processes. The paste viscosity and viscoelastic properties of OSC_s were enhanced after SSP. Both the swelling power and transparency of OSA esterified starch increased with DS values after SSP. The content of resistant starch (RS) among OSA esterified starch increased from 33.18 % to 45.33 %, which mainly occurred when SSP was introduced into the OS starch synthesis process. In summary, SSP at different temperatures promoted the unique physicochemical properties of OSC_s specimens by increasing their DS values.

Lipase-polydopamine magnetic hydrogel microspheres for the synthesis of octenyl succinic anhydride starch

Octenyl succinic anhydride (OSA) starch is an important edible additive in the food field, and its synthesis method has attracted much attention. Lipase as a biocatalyst can improve the synthesis efficiency of OSA starch, and significantly inhibit the occurrence of side reactions. However, free lipase has not been widely applied in the synthesis of OSA starch due to the difficulty of separation from starch and poor reusability. In this work, a promising strategy for the synthesis of OSA starch catalyzed by lipase immobilized on polydopamine magnetic hydrogel microspheres (PMHM) is reported. The prepared lipase-polydopamine magnetic hydrogel microspheres (L-PMHM) can be uniformly dispersed in starch slurry, which is conducive to the full contact between lipase and starch. L-PMHM (Km =2.6276 μmol/mL) exhibits better affinity to the substrate than free lipase (Km = 3.4301 μmol/mL). Compared with the OSA starch catalyzed by free lipase (DS = 0.0176), the degree of substitution of OSA starch catalyzed by L-PMHM is up to 0.0277 in a short reaction time. In cyclic catalysis, L-PHMM can remain about 48 % of their original activity after 20 reuses and can be quickly separated from the product. These results suggest that L-PMHM has great potential as a biocatalyst for the efficient synthesis of OSA starch.

Structure and Menthone Encapsulation of Corn Starch Modified by Octenyl Succinic Anhydride and Enzymatic Treatment

In order to improve the ability of starch to absorb menthone, corn starch was modified by enzymatic treatment (amyloglucosidase and α-amylase) combined with octenyl succinic anhydride (OSA) esterification. The oil absorption rate of starch modified by enzymatic treatment followed by OSA (P-OSA) reached 101.33%, whereas that of samples with reverse action sequences (OSA-P) was only 59.67%. The degree of substitution of OSA-P was also generally lower than that of P-OSA. At high OSA addition, OSA-P had a smaller specific surface area with fewer pores because octenyl succinic (OS) groups impeded the enzymatic treatment. Compared with OSA-P, the lamellar structure of P-OSA is sparser and less ordered. Owing to its pores, P-OSA was beneficial for the reaction to occur inside the granules, which was observed by Raman spectroscopy and laser confocal microscopy. At high OSA addition, the loading of P-OSA to menthone could reach 64.34 mg/g.

Preparation and characterization of octenyl succinylated starch microgels via a water-in-oil (W/O) inverse microemulsion process for loading and releasing epigallocatechin gallate

Corn starch (CS), octenyl succinic anhydride modified corn starch (OSCS) and shells (OSC_s) microgels have been prepared using water-in-oil (W/O) inverse microemulsions for loading and releasing of epigallocatechin gallate (EGCG). The structural and morphological properties of CS, OSCS, and OSC_s microgels were characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), Transmission electron microscopy (TEM), and Thermogravimetric analysis (TGA). The strong hydrogen bonds between starch molecules in the W/O system and interplay between hydroxyl groups of EGCG and oxygen atoms of starch microgels were formed. OSC_s microgel showed low average particle size and weak thermal stability with an irregular shape and a typical V-type crystalline structure. Encapsulation efficiency (EE) and clearance rate of 2,2-diphenyl-1-picrylhydrazyl (DPPH) for EGCG were ranged between 41.78 and 63.89% and 75.53-85.37%, respectively, when absorbed into OSCS and OSC_s microgels, the values which were higher than that of CS microgel. Further, OS starch microgels (particularly OSC_s) modulated the slow release of EGCG into simulated gastrointestinal tract conditions and therefore could be proposed as an encapsulating agent for loading polyphenols.