Preparation of poly(sodium 4-styrene sulfonate) grafted magnetic chitosan microspheres for adsorption of cationic dyes

Theoretical investigation on regulating photophysical properties and proton transfer behavior by electronegativity for near-infrared emitting styryl dyes

Our main focus is to explore the atomic electronegativity-dependent photoinduced behavior of styryl derivatives (HBO, HBS, and HBSe). The results of structural parameter calculation by the DFT method show that the intramolecular hydrogen bonds of normal and tautomer form are strengthened and weakened, respectively, in an excited state (S1), which is conducive to the excited intramolecular proton transfer (ESIPT) process. The enhancement of excited hydrogen bond is beneficial to the ESIPT process from the aspects of infrared vibration frequency (IR), Mulliken's charge analysis, and density gradient reduction (RDG). Additionally, by determining the bond energy with the band critical point (BCP) parameter, we found that the lower the electronegativity of the atom, the larger the hydrogen bond strength at the excited state and the more likely ESIPT reaction occurs. Meanwhile, the intramolecular H-bonds O-H…N in HBO, HBS, and HBSe are enhanced with the weakened electron-withdrawing capacity of the atom (from O to S and Se). Subsequently, frontier molecular orbital (FMOs) and charge density difference (CDD) analyses essentially revealed that electron redistribution induces the ESIPT process. Low atomic electronegativity exhibits the high chemical activity of the excited state. Furthermore, to demonstrate the electronegativity-dependent ESIPT behavior of the system, we built potential energy curves (PECs) and located the transition states (TS) of proton transfer processes.

Adsorption of Levofloxacin onto Graphene Oxide/Chitosan Composite Aerogel Microspheres

The removal of pharmaceutical residues from water resources using bio-based materials is very important for human safety and health. Bio-based graphene oxide/chitosan (GO/CS) aerogel microspheres were fabricated with emulsification and cross-linking, followed by freeze drying, and were used for the adsorption of levofloxacin (LOF). The obtained GO/CS aerogel microspheres were characterized with scanning electron microscopy (SEM), Fourier-transform infrared (FTIR), and thermogravimetry (TG). The effects of GO content, pH value, and temperature on their adsorption capacity were investigated. With the incorporation of 40 wt% GO, the adsorption capacity increased from 9.9 to 45.6 mg/g, and the highest adsorption capacity, 51.5 mg/g, was obtained at pH = 8 and T = 25 °C. In addition, to obtain deeper insight into the adsorption process, the thermodynamics and kinetics of the process were also investigated with four different models of LOF adsorption. The thermodynamic modeling results revealed that LOF adsorption is exothermic, and the kinetic investigation demonstrated that LOF adsorption is generally consistent with a pseudo-first-order rate law.

Poly(acrylic acid-co-2-acrylamido-2-methyl-1-propanesulfonic acid)-grafted chitosan hydrogels for effective adsorption and photocatalytic degradation of dyes

As a result of the growth of industrialization and urbanization, the water ecosystem is contaminated by various pollutants, including heavy metal ions and dyes. The use of low-cost and environmentally friendly dye adsorbents has been investigated. A hydrogel was fabricated via graft polymerization of acrylic acid (AA) and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) onto chitosan. The hydrogel was used as a dye adsorbent and support for a zinc oxide (ZnO) powder photocatalyst. The adsorption capacity of the bare hydrogel was greater towards cationic dyes than anionic dyes. Grafting P(AA-co-AMPS) exhibited a 23-time increase in adsorption capacity towards crystal violet (CV) compared to pristine chitosan. The effect of the AA-AMPS molar ratio on CV adsorption was studied. A hydrogel with an AA-AMPS ratio of 10 : 1 had the highest adsorption capacity towards CV in water, removing 91% of the dye in 12 h. The maximum adsorption capacity was 2023 mg g-1. The adsorption kinetics and isotherm were described by the pseudo-second-order model and the Langmuir model, respectively. ZnO particles were in situ synthesized within the 10 : 1 hydrogel to facilitate the recovery of the photocatalyst. The ZnO hydrogel composite could remove 95% and 92% of CV from solutions on the 1st and 2nd cycle, respectively. In addition, the hydrogel composite containing only 8.7 wt% of ZnO particles effectively degraded adsorbed CV under sunlight and could be reused without requiring a chemical regeneration or photocatalyst recovery procedure. This hydrogel composite is an effective dual-functional material for the adsorption and photodegradation of dye pollutants in wastewater.

Heparin-Mimetic Chitooligosaccharides-Based Monoliths Obtained from C/W Emulsions: Hemocompatibility and Toxin Removal Ability

Hemoperfusion (HP) is one of the most prominent therapies for treating uremia, hyperbilirubinemia, and acute drug toxicity. The comprehensive performance of currently used porous HP adsorbents needs to be improved due to the impediment to their synthesis strategy. Herein, green carbon dioxide-in-water high internal phase emulsions (C/W HIPEs) were utilized and emulsified with poly(vinyl alcohol) (PVA) for the formation of a heparin-mimetic chitosan oligosaccharides/poly(acrylamide-co-sodium 4-styrenesulfonate) [COS/P(AM-co-SSS)] monolith, which exhibited good mechanical properties, stable swelling performance, hydrophilic properties, anticoagulant effect, and low hemolysis. It showed a strong toxin adsorption capacity (415.2 mg/g for creatinine, 199.3 mg/g for urea, 279.5 mg/g for bilirubin, and 160 mg/g for tetracycline). The adsorption process of porous COS/P(AM-co-SSS) followed the pseudo-second-order kinetic and Langmuir isotherm models. Moreover, the porous materials had a strong electrostatic force on creatinine. The removal of creatinine by simulated in vitro blood perfusion was 80.2% within 30 min. This work provides a green preparation strategy for developing novel HP materials, highlighting their potential application value in blood and environmental purification.

Sulfonated Hydrogel Formed via CO2-in-Water Emulsion: Potential in Antibiotic Removal

Herein, a green, carbon dioxide-in-water high-internal-phase emulsion (C/W HIPEs) was developed and stabilized with polyvinyl alcohol (PVA) for the formation of chitosan oligosaccharide/poly(acrylamide-co-sodium 4-styrene sulfonate) [COS/P(AM-co-SSS)] monolithic porous hydrogel. The obtained monolith was characterized via FT-IR and SEM. The SEM patterns depicted that the monoliths were interconnected, the void sizes were 78.5 µm, and the interconnected pore throats were 28 μm approximately. Mechanical measurement results indicated that the maximum compress stress of the monolith could reach 334.4 kPa at 90% strain, and it exhibited good mechanical stability. After 200 cycles of compression, it could still recover its original shape without cracking. The obtained COS-based monolith was selected to remove tetracycline (TC) for evaluating the adsorptive features of the interpenetrating pore-containing monolith. The monolithic COS/P(AM-co-SSS) hydrogel behaved with strong antibiotic adsorption capacity (1600.4 mg/g for TC). The adsorption process agreed well with the pseudo-second-order kinetic and Langmuir isothermal models. In addition, the porous monolith had a strong electrostatic force on TC according to the thermodynamic study. This work provides a green route for the development of novel monolithic hydrogels and highlights its potential application in the treatment of antibiotic-containing wastewater.

A multifunctional polyacrylamide/chitosan hydrogel for dyes adsorption and metal ions detection in water

Removing noxious dyes and detecting excessive metal ions in water are both effective means to prevent damage from contaminants and ensure water safety. The emphasis problems were addressed by preparation a polyacrylamide chitosan (PAAM/CS) hydrogel. Polyacrylamide (PAAM) provides overall mechanical strength to carry loads and facilitate circulation, chitosan (CS) provides adsorption positions with high adsorption capacity. Which made that PAMM/CS hydrogel efficiently performed sorption of xylenol orange (XO). As the functional dye, XO binds to PAAM/CS and confers colorimetric properties on PAAM/CS hydrogels. XO sorbed hydrogel realized fluorescence dual-signal detection of Fe3+ and Al3+ in water. The significant swelling and adsorption potency of the hydrogel, combined with the dual-signal detection capability of XO sorbed hydrogel, make this hydrogel a versatile material for environmental applications.

Methylene blue removal from aqueous solutions using a biochar/gellan gum hydrogel composite: Effect of agitation mode on sorption kinetics

Hydrogel membranes are prepared by casting a mixture of gellan gum (associated with PVA) and biochar produced from a local Egyptian plant. The mesoporous material is characterized by a specific surface area close to 134 m² g^-1, a residue of 28 % (at 800 °C), and a pH_PZC close to 6.43. After grinding, the material is tested for Methylene Blue sorption at pH 10.5: sorption capacity reaches 1.70 mmol MB g^-1 (synergistic effect of the precursors). The sorption isotherms are fitted by both Langmuir and Sips eqs. MB sorption increases with temperature: the sorption is endothermic (∆H°: 12.9 kJ mol^-1), with positive entropy (∆S°: 125 J mol^-1 K^-1). Uptake kinetics are controlled by agitation speed (optimum ≈200 rpm) and resistance to intraparticle diffusion. The profiles are strongly affected by the mode of agitation: the equilibrium time (≈180 min) is reduced to 20-30 min under sonication (especially at frequency: 80 kHz). The mode of agitation controls the best fitting equation: pseudo-first order rate agitation for mechanical agitation contrary to pseudo-second order rate under sonication. The sorption of MB is poorly affected by ionic strength (loss <6 % in 45 g L^-1 NaCl solution). Desorption (faster than sorption) is completely achieved using 0.7 M HCl solution. At the sixth recycling, the loss in sorption is close to 5 % (≈ decrease in desorption efficiency). The process is successfully applied for the treatment of MB-spiked industrial solution: the color index decreases by >97 % with a sorbent dose close to 1 g L^-1; a higher dose is required for maximum reduction of the COD (60 % at 3 g L^-1).

Synthesis, characterization, DFT studies, and adsorption properties of sulfonated starch synthesized in deep eutectic solvent

In this study, sulfonated starch (SS) was successfully synthesized using sulfamic acid as a sulfonating agent in a deep eutectic solvent (DES). Four-factor and three-level orthogonal experiments were conducted to determine the optimal preparation conditions, which were found to be a molar ratio of starch to urea of 1:20, a reaction temperature of 90 °C, a reaction time of 5 h, and a stirring speed of 200 rpm. The sulfonation reaction mechanism was extensively studied using various techniques, including Fourier transform infrared spectroscopy, elemental analysis, X-ray diffraction, molecular weight, particle distribution, X-ray photoelectron spectroscopy, scanning electron microscopy, and DFT calculations. The results showed that the sulfonation reaction slightly damaged starch granules, occurred on the surface of starch granules, and on the O6 atoms of the glucose unit. SS exhibited a wide pH range of application (5-10), a fast adsorption rate (400 s to reach adsorption equilibrium), and a high adsorption capacity (118.3 mg/g) under optimal conditions. The adsorption process of SS for methylene blue followed the pseudo-first-order kinetic model and was consistent with the Langmuir model, which was endothermic and spontaneous. The adsorption process was attributed to hydrogen bonding and electrostatic interactions.

Removal of highly concentrated methylene blue dye by cellulose nanofiber biocomposites

The contamination of water by dyes in high concentrations is a worldwide concern, and it has prompted the development of efficient, economical, and environmentally friendly materials and technologies for water purification. The hydration and adsorption capacity for methylene blue (MB) in biocomposites (BCs) based on cellulose nanofiber (CNF) (0 to 2 wt%) were studied. BCs were synthesized through a simple and straightforward route and characterized by spectroscopy, microscopic techniques and thermogravimetric analysis, among others. Hydration studies showed that BCs prepared with 2 wt% of CNF can absorb large volumes of water, approximately 2274 % in the case of poly 2-acrylamide-2-methyl-1-propanesulfonic acid (PAMPS)-CNF and 2408 % in poly sodium 4-styrene sulfonate (PSSNa)-CNF. These BCs showed outstanding adsorption capacity for highly concentrated MB solutions (4536 mg g^-1 PAMPS-CNF and 11,930 mg g^-1 PSSNa-CNF). It was confirmed that the adsorption mechanism is through electrostatic interactions. Finally, BCs showed high MB adsorption efficiency after several sorption-desorption cycles and on a simulated textile effluent. Furthermore, the theoretical results showed a preferential interaction between MB and the semiflexible polymer chains at the lowest energy setting. The development and study of a new adsorbent material with high MB removal performance that is easy to prepare, economical and reusable for potential use in water purification treatments was successfully achieved.

A magnetic MIL-125-NH2@chitosan composite as a separable adsorbent for the removal of Cr(VI) from wastewater

Metal-organic frameworks (MOFs) are gradually used since of their huge specific surface area and superior pore structure. However, there are problems such as easy aggregation and difficult separation in water treatment. In this study, we prepared composite microspheres (FMCS-1) by modifying MIL-125-NH₂ with Fe₃O₄ and chitosan. The structural characterization and performance analysis of the materials showed that the introduction of chitosan effectively prevents the stacking of MOFs. The magnetic test manifested that Fe₃O₄ solved the problem of the difficult separation of MOFs from water. The removal potential of toxic Cr(VI) was tested by adsorption experiments. The isotherm model indicated that FMCS-1 is a single molecular layer adsorbent with a maximum adsorption capacity of 109.46 mg/g at pH = 2. The adsorption kinetics showed that the adsorption of Cr(VI) by FMCS-1 was chemical adsorption. The acid resistance test demonstrated that FMCS-1 can exist stably in acid solutions. The recycling experiments proved that the adsorbent can be reused and the removal percentage still reaches 50 % after 5 cycles. This work expands the application of MOFs in water treatment and also provides an effective adsorbent for Cr(VI) removal.

Isotherm, Thermodynamics, and Kinetics of Methyl Orange Adsorption onto Magnetic Resin of Chitosan Microspheres

Severe environmental pollution problems arising from toxic dyestuffs (e.g., methyl orange) are receiving increasing attention. Therefore, dyes' safe removal has become a research hotspot. Among the many physical-chemical removal techniques, adsorption using renewable biological resources has proved to be more advantageous over others due to its effectiveness and economy. Chitosan is a natural, renewable biopolymer obtained by deactivated chitin. Thus, the magnetic resin of chitosan microspheres (MRCM), prepared by reversed-phase suspension cross-linking polymerization, was used to remove methyl orange from a solution in a batch adsorption system. The main results are as follows: (1) The results of physical and swelling properties of MRCM indicated that MRCM was a type of black spherical, porous, water-absorbing, and weak alkali exchange resin, and it had the ability to adsorb methyl orange when it was applied in solutions above pH 2.0. (2) In batch adsorption studies, the maximum adsorption capacity was obtained at pH 5; the adsorption equilibrium time was 140 min; and the maximum adsorption was reached at 450 mg/L initial concentration. (3) Among the three isotherm adsorption models, Langmuir achieved the best fit for the adsorption of methyl orange onto MRCM. (4) The adsorption thermodynamics indicated that the adsorption was spontaneous, with increasing enthalpy, and was driven by the entropy. (5) The pseudo-second-order kinetics equation was most suitable to describe the adsorption kinetics, and the adsorption kinetics was also controlled by the liquid-film diffusion dynamics. Consequently, MRCM with relatively higher methyl orange adsorption exhibited the great efficiency for methyl orange removal as an environment-friendly sorbent. Thus, the findings are useful for methyl orange pollution control in real-life wastewater treatment applications.

Accurate data prediction by fuzzy inference model for adsorption of hazardous azo dyes by novel algal doped magnetic chitosan bionanocomposite

A bionanocomposite comprising of magnetic chitosan doped with algae isolated from native habitat was fabricated and utilized as an efficient adsorbent for the removal of hazardous azo dyes, namely, Direct Red 31 (DR31) and Direct Red 28 (DR28). The algal doped magnetic chitosan (Alg@mCS) was comprehensively characterized by Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Analysis (EDAX), Fourier Transform Infrared Spectroscopy (FTIR), X-ray diffraction analysis (XRD), and Brunauer-Emmett-Teller (BET). On the sorption of dyes, the influence of various process variables such as pH, adsorbent dosage, contact time, temperature, and initial dyes concentration were addressed. The adsorbent demonstrated maximal removal of DR31 and DR28 at pH 5 and 3, respectively. The maximum adsorption capacity of DR31 and DR28 was observed at Alg@mCS dose of 0.6 g L^-1 and 7 g L^-1 in 10 and 20 min, respectively. The Redlich Peterson isotherm model was shown to be appropriate for dye adsorption, indicating monolayer coverage of the dyes on the adsorbent surface (R² > 0.99). The adsorption process followed pseudo-second-order kinetics (R² > 0.99). Based on 320 experimental datasets from batch studies and interpolated data, adaptive neuro-fuzzy inference system (ANFIS) models were utilized to estimate dye elimination (percent). A number of parameters were calculated to validate the model's applicability. The Alg@mCS was proven to be a useful adsorbent for eliminating toxic and harmful azo dyes from aqueous solutions.

Wastewater Treatment by Polymeric Microspheres: A Review

This review addresses polymer microspheres used as adsorbent for wastewater treatment. The removal of various pollutants (including dyes, heavy metal ions, and organic pollutants) is a prominent issue, as they can cause severe health problems. Porous microspheres can provide large specific area and active sites for adsorption or photo degradation. Enhancement in performance is achieved by various modifications, such as the introduction of nanoparticles, magnetic particles, and ZIF-8. Some microspheres were synthesized from synthetic polymers such as vinylic polymer and polydopamine (PDA) through a facile fabrication process. Natural polymers (such as cellulose, alginate, and chitosan) that are biodegradable and eco-friendly are also used. The adsorbents used in industrial application require high adsorption capacity, thermal stability, and recyclability. Batch adsorption experiments were conducted to investigate the optimal conditions, influence of related factors, and adsorption capacities. Insights regarding the adsorption mechanisms were given from the kinetic model, isotherm model, and various characterization methods. The recyclability is investigated through regeneration ratio, or their maintenance of their capability through repeated adsorption-desorption cycles. The high potential of polymer microsphere for the removal of pollutants from wastewater is shown through the high adsorption capacities, environmentally friendliness, and high stability.

Amino-Functionalized Magnetic Porous Organic Polymer for Selective Removal of Toxic Cationic Dyes from Textile Wastewater

Porous organic polymers (POPs) with fascinating porous properties are promising candidates for the removal of organic dyes from textile wastewater. In this research work, an amino-functionalized magnetic POP (FC-POP-EDA@Fe3O4) containing...

Phenylboronic acid-functionalized cross-linked chitosan magnetic adsorbents for the magnetic solid-phase extraction of benzoylurea pesticides

In this study, a 4-formylphenylboronic acid-modified cross-linked chitosan magnetic nanoparticle (FPBA@CCHS@Fe₃ O₄ ) was fabricated. The synthesized material was utilized as the magnetic solid-phase extraction adsorbent for the enrichment of six benzoylurea pesticides. In addition to B-N coordination, FPBA@CCHS@Fe₃ O₄ interacts with benzoylureas through hydrogen bonds and π-π stacking interaction on account of rich active groups (amino and hydroxyl) and aromatic rings in structure. Compared to traditional extraction methods, less adsorbent (20 mg) and reduced extraction time (3 min) were achieved. The adsorbent also exhibited good reusability (no less than 10 times). Coupled with a high-performance liquid chromatography-diode array detector, satisfactory recoveries (89.1-103.9%) and an acceptable limit of detection (0.2-0.7 μg/L) were obtained. Under optimized conditions, the established method was successfully applied to the tea infusion samples from six major tea categories with acceptable recoveries ranging from 76.8 to 110%, indicating its application potential for the quantitative detection of pesticides in complex matrices.

Chitosan immobilization and Fe3O4 functionalization of olive pomace: An eco-friendly and recyclable Pb2+ biosorbent

An effective and sustainable biosorbent (MagOPIC) was prepared from chitosan and olive pomace by the combined action of immobilization and magnetic modification to remediate Pb²⁺-contaminated waters. Pb²⁺ sorption yield at the end of the equilibrium (45 min) period was estimated to be 98.56 ± 0.28% at pH 5.5. Agitation speed, ionic strength, and temperature did not significantly affect the Pb²⁺ biosorption. Biosorption kinetics are successfully fitted by the pseudo-second-order equation while the equilibrium biosorption data are properly modeled using the Freundlich and D-R isotherms. MagOPIC has also exhibited a high biosorption yield in the column tests (≥99%) and showed remarkable stability up to twenty consecutive regeneration cycles. Furthermore, it was successfully used for the treatment of Pb²⁺ containing real wastewater. The findings of this work highlighted the potential use of MagOPIC as a novel, cost-effective and eco-friendly biosorbent for the Pb²⁺ removal from the contaminated aquatic phase.

Synthesis and characterization of chitosan/polyacrylamide hydrogel grafted poly(N-methylaniline) for methyl red removal

Chitosan/polyacrylamide hydrogel grafted poly(N-methylaniline) (CS/PACM-gr-PNMA) was good synthesized by chemical oxidative radical polymerization using potassium persulphate (KPS). The obtained polymer samples are characterized using IR and Uv-visible spectroscopy. Both surface properties and thermal stability were studied using XRD, SEM, BET and TGA techniques respectively. The characterized polymeric samples were used as a new sorbent for methyl red (MR). MR as an example of azo-dyes presence as pollutants in industrial wastewater which cause physiological damages was chosen to uptake. The influence of contact time, adsorbent dose, and temperature on the efficiency of CS/PACM-gr-PNMA towards the removal of MR was investigated. The efficacy was equal to 98% through 120 min at room temperature. The obtained data show that, ∆H = -21.478 kJ mol^-1, so adsorption process is physically spontaneous and follow Freundlich isotherm. The sorption process of MR on the surface of CS/PACM-gr-PNMA is proceed via the Lagergren pseudo-second order reaction. This confirms the removal mechanism by both chemical and physical adsorption of MR with both unpaired and π electrons present in polymer structure on NH, NH_2, and benzene or quinoid units respectively. In addition, it can explain the chemical adsorption type which occurs through sharing between the used adsorbent materials and the dissolved materials beside the physical adsorption.