A polyurethane foam membrane filled with double cross-linked chitosan/carboxymethyl cellulose gel and decorated with ZSM-5 nano zeolite: Simultaneous dye removal

Development of a novel bionanocomposite of UiO-66/xanthan gum/alginate crosslinked by calcium chloride for azo dye removal: Insight into adsorption kinetics, isotherms, and thermodynamics

In the present work, UiO-66/xanthan gum/alginate bionanocomposite adsorbent was fabricated using the in-situ crosslinking-gelation method, characterized by different techniques, and finally used for the removal of methylene blue dye from aqueous solution. Adsorption studies were performed using batch experiments and the influencing operational parameters such as contact time, initial pH solution, temperature, initial dye concentration, adsorbent dose, pHPZC, swelling, regeneration, and reuse of the adsorbent were investigated. The various kinetic models (pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion) and isotherm models (Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich) were used to analysis of the experiment results. The results were best fitted to the pseudo-second-order kinetic and Langmuir isotherm models. The maximum adsorption capacity of dye on the adsorbent was obtained at 9.96 mg/g at pH = 11. The value of pHPZC for the adsorbent was obtained at about 8. According to thermodynamic parameters, the dye adsorption was found as spontaneous and endothermic due to the negative value of the ΔG° and ΔH°. After 4 times of reusability cycles, the adsorption efficiency remained above 86 %, which represented a certain regeneration ability. As a result, this research indicates that UiO-66/xanthan gum/alginate bionanocomposite can be utilized as a promising bio-adsorbent for azo dye removal from contaminated wastewater.

Biosorption of a common micropollutant (methylene blue) from a water environment by chemically activated biomass of a widely available plant species (Pyracantha coccinea M. J. Roemer)

Recently, to protect the health of aquatic life and, indirectly, all living things, biomass-based substances have been increasingly applied as biosorbent materials to remove micropollutant agents from an aquatic environment. However, these studies are under development, and the search for more successful materials continues. Here, the biosorption of a common micropollutant, methylene blue, from an aquatic environment was investigated using the chemically activated biomass of a widely available plant species, Pyracantha coccinea M. J. Roemer. The biosorption efficiency of the biosorbent material was improved by optimizing the experimental conditions, including the contact time, micropollutant load, pH, and biosorbent material amount, and the highest performance was observed at t = 360 mins, C0 = 15 mg L-1, pH = 8 and m = 10 mg. The pseudo-second-order kinetics model and Freundlich isotherm model were in good agreement with the experimentally obtained results. The thermodynamic study suggested that the micropollutant biosorption was a favorable, spontaneous, and physical process. The micropollutant-biosorbent interaction mechanism was presented using SEM and FTIR studies. The maximum Langmuir biosorption capacity of the biosorbent was determined to be 156.674 mg g-1. The activation operation more than doubled the biosorption potential of the biosorbent material. Thus, the present study showed that the chemically activated plant biomass-based material could be a promising biosorbent for the effective removal of the micropollutant from water environment.

Combined use of novel chitosan-grafted N-hydroxyethyl acrylamide polyurethane and human dermal fibroblasts as a construct for in vitro-engineered skin

A rich plethora of information about grafted chitosan (CS) for medical use has been reported. The capability of CS-grafted poly(N-hydroxyethyl acrylamide) (CS-g-PHEAA) to support human dermal fibroblasts (HDFs) in vitro has been proven. However, CS-grafted copolymers lack good stiffness and the characteristic microstructure of a cellular matrix. In addition, whether CS-g-PHEAA can be used to prepare a scaffold with a suitable morphology and mechanical properties for skin tissue engineering (STE) is unclear. This study aimed to show for the first time that step-growth polymerizations can be used to obtain polyurethane (PU) platforms of CS-g-PHEAA, which can also have enhanced microhardness and be suitable for in vitro cell culture. The PU prepolymers were prepared from grafted CS, polyethylene glycol, and 1,6-hexamethylene diisocyanate. The results proved that a poly(saccharide-urethane) [(CS-g-PHEAA)-PU] could be successfully synthesized with a more suitable microarchitecture, thermal properties, and topology than CS-PU for the dynamic culturing of fibroblasts. Cytotoxicity, proliferation, histological and immunophenotype assessments revealed significantly higher biocompatibility and cell proliferation of the derivative concerning the controls. Cells cultured on (CS-g-PHEAA)-PU displayed a quiescent state compared to those cultured on CS-PU, which showed an activated phenotype. These findings may be critical factors in future studies establishing wound dressing models.

Lignin microparticles-reinforced cellulose filter paper for simultaneous removal of emulsified oils and dyes

The presence of multiple pollutants in wastewater, often with complex interactions, poses a significant challenge for conventional membranes to effectively remove multiple pollutants simultaneously. Herein, a lignin microparticles-reinforced cellulose filter paper (FP@AL-LS-DA) was fabricated via an aldol condensation between lignin and cellulose filter paper and cross-linking with dopamine hydrochloride (DA), which showed desired rejection of oil-in-water emulsions and dyes. Characterizations revealed that the addition of lignin and DA effectively narrowed the pore size (from 4.45 μm to 2.01 μm) and enhanced the rigidity and stability of the cellulose filter paper, thus making it not easily damaged in the water environment and showing excellent tolerance to strong acid and high-salt environments. The oil-in-water emulsions removal efficiency was higher than 99 % even after ten times usage, and the oil flux was kept stable at 52.54 L·m^-2·h^-1, indicating that FP@AL-LS-DA had outstanding reusability and stability. Remarkably, FP@AL-LS-DA showed excellent removal efficiency (>99 %) for complex pollutants containing dyes and oil-in-water emulsions. In this work, we demonstrate a lignin microparticles-reinforced cellulose filter paper that is simple to prepare and can efficiently separate oil-in-water emulsions and remove dyes.

Carboxymethyl Cellulose-Based Polymers as Promising Matrices for Ficin Immobilization

The present work is devoted to research on the interaction between carboxymethyl cellulose sodium salt and its derivatives (graft copolymer of carboxymethyl cellulose sodium salt and N,N-dimethyl aminoethyl methacrylate) with cysteine protease (ficin). The interaction was studied by FTIR and by flexible molecular docking, which have shown the conjugates' formation with both matrices. The proteolytic activity assay performed with azocasein demonstrated that the specific activities of all immobilized ficin samples are higher in comparison with those of the native enzyme. This is due to the modulation of the conformation of ficin globule and of the enzyme active site by weak physical interactions involving catalytically valuable amino acids. The results obtained can extend the practical use of ficin in biomedicine and biotechnology.

Facile Synthesis and Characterization of CeO2-Nanoparticle-Loaded Carboxymethyl Cellulose as Efficient Protective Films for Mild Steel: A Comparative Study of Experiential and Computational Findings

Corrosion is considered to be the most severe problem facing alloys and metals, one that causes potentially dangerous industrial issues such as the deterioration of buildings and machinery, and corrosion in factory tanks and pipelines in petroleum refineries, leading to limited lifetime and weak efficacy of such systems. In this work, novel CeO₂-nanoparticle-loaded carboxymethyl cellulose (CMC) was successfully prepared by using a simple method. The structural configuration of the prepared CeO₂-nanoparticle-loaded CMC was investigated by FE-SEM/EDX, TEM, FT-IR, and thermal analyses. The corrosion protection proficiency of uncoated and coated mild steel with CeO₂-CMC systems in 1.0 M HCl solutions was studied by E_OCP-time, EIS, and PDP tools. Moreover, the relationship between the structure of coating films and their corrosion protection was confirmed by DFT calculation and MC simulation. The obtained findings from the studied methods showed that the prepared CeO₂-CMC-coated films reported high corrosion resistance. The protection capacity augmented with ceria presents an increase of up to 3% to achieve 98.4%. DFT calculation and MC simulation confirmed the influence of the chemical construction of coated films on its protection capacity, which was in accordance with the experimental results.

Influence of Electric Field on Proliferation Activity of Human Dermal Fibroblasts

In this work, an electrically conductive composite based on thermoplastic polyimide and graphene was obtained and used as a bioelectrode for electrical stimulation of human dermal fibroblasts. The values of the electrical conductivity of the obtained composite films varied from 10-15 to 102 S/m with increasing graphene content (from 0 to 5.0 wt.%). The characteristics of ionic and electronic currents flowing through the matrix with the superposition of cyclic potentials ± 100 mV were studied. The high stability of the composite was established during prolonged cycling (130 h) in an electric field with a frequency of 0.016 Hz. It was established that the composite films based on polyimide and graphene have good biocompatibility and are not toxic to fibroblast cells. It was shown that preliminary electrical stimulation increases the proliferative activity of human dermal fibroblasts in comparison with intact cells. It is revealed that an electric field with a strength E = 0.02-0.04 V/m applied to the polyimide films containing 0.5-3.0 wt.% of the graphene nanoparticles activates cellular processes (adhesion, proliferation).