Characterisation and functionality of inhalation anhydrous lactose

Lubricant Sensitivity of Direct Compression Grades of Lactose in Continuous and Batch Tableting Process

Modern pharmaceutical manufacturing based on Quality by Design and digitalisation is revolutionising the pharmaceutical industry. Continuous processes are promoted as they increase efficiency and improve quality control. Compared to batch blending, continuous blending is easier to scale and provides advantages for achieving blend homogeneity. One potential challenge of continuous blending is the risk of over-lubrication. In this study, blending homogeneity and lubricant sensitivity are investigated for both batch and continuous processes. Given their distinct chemical structures and morphologies, anhydrous lactose and granulated lactose are expected to exhibit varying sensitivities to changes in process settings across both technologies. The findings suggest that both lactose grades provide highly stable blends that can be safely utilised in both batch and continuous modes. Optimisation should focus on process variables, such as the quality of loss-in-weight feeders used for dosing low doses of ingredients. The most significant process parameter for lubricant sensitivity was the type of lactose used. Anhydrous lactose produced harder tablets than the more porous granulated lactose but was more sensitive to lubrication at the same settings. The magnesium stearate content and its interaction with the type of lactose are also critical factors, with magnesium stearate having a counterproductive impact on tabletability.

Predicting in vitro lung deposition behavior of combined dry powder inhaler via rheological properties

Dry powder inhaler (DPI) for pulmonary delivery is currently the primary treatment for asthma and COPD (chronic obstructive pulmonary disease), an increasing number of combined DPIs (containing two or more drugs in one inhaler) have been developed to complement the effect of single DPIs. Based on our previous studies, the rheological properties can be a potential tool used to predict the in vitro lung deposition behavior of DPI formulations. However, it is unknown whether such a prediction model is suitable for combination systems. Therefore, this study aimed to verify the applicability of using powder rheological properties to predict in vitro drug deposition behavior in combined DPI formulations. Two drugs (fluticasone propionate and salmeterol xinafoate) and their combination of DPI formulations were prepared using fine lactose content (in the range of 1%-20%) as a variable. The physicochemical properties of the powder mixtures such as particle size and content uniformity were characterized. The rheological properties of the powder mixtures were measured by FT4 rheometer, the aerodynamic behavior of the DPI formulations was evaluated by a new generation impactor (NGI), and the effect of flowability and adhesion on the deposition of the fine particle fraction (FPF) was investigated by principal component analysis (PCA). The results showed that the combined DPI formulations with larger particle interaction forces have certain differences from the aerodynamic behavior of the single DPI formulations. The regularity of rheological properties affecting FPF revealed in single DPI is still applicable to combined DPI, the parameters basic flowability energy (BFE), representing flowability, and flow factor (ff), Cohesion representing adhesion, can be well linearly related to the FPF. The results of the principal component analysis showed that better flowability and suitable adhesion contributed to higher in vitro deposition of the drug in the formulation, and the contribution of adhesion (75.42%) was greater than that of flowability (24.58%). In conclusion, rheological properties is an effective tool for predicting the deposition behavior of DPI not only in single but also in combined DPIs.

The Optimisation of Carrier Selection in Dry Powder Inhaler Formulation and the Role of Surface Energetics

This review examines the effects of particle properties on drug-carrier interactions in the preparation of a dry powder inhaler (DPI) formulation, including appropriate mixing technology. The interactive effects of carrier properties on DPI formulation performance make it difficult to establish a direct cause-and-effect relationship between any one carrier property and its effect on the performance of a DPI formulation. Alpha lactose monohydrate remains the most widely used carrier for DPI formulations. The physicochemical properties of α-lactose monohydrate particles, such as particle size, shape and solid form, are profoundly influenced by the method of production. Therefore, wide variations in these properties are inevitable. In this review, the role of surface energetics in the optimisation of dry powder inhaler formulations is considered in lactose carrier selection. Several useful lactose particle modification methods are discussed as well as the use of fine lactose and force control agents in formulation development. It is concluded that where these have been investigated, the empirical nature of the studies does not permit early formulation prediction of product performance, rather they only allow the evaluation of final formulation quality. The potential to leverage particle interaction dynamics through the use of an experimental design utilising quantifiable lactose particle properties and critical quality attributes, e.g., surface energetics, is explored, particularly with respect to when a Quality-by-Design approach has been used in optimisation.

Recent developments in lactose blend formulations for carrier-based dry powder inhalation

Lactose is the most commonly used excipient in carrier-based dry powder inhalation (DPI) formulations. Numerous inhalation therapies have been developed using lactose as a carrier material. Several theories have described the role of carriers in DPI formulations. Although these theories are valuable, each DPI formulation is unique and are not described by any single theory. For each new formulation, a specific development trajectory is required, and the versatility of lactose can be exploited to optimize each formulation. In this review, recent developments in lactose-based DPI formulations are discussed. The effects of varying the material properties of lactose carrier particles, such as particle size, shape, and morphology are reviewed. Owing to the complex interactions between the particles in a formulation, processing adhesive mixtures of lactose with the active ingredient is crucial. Therefore, blending and filling processes for DPI formulations are also reviewed. While the role of ternary agents, such as magnesium stearate, has increased, lactose remains the excipient of choice in carrier-based DPI formulations. Therefore, new developments in lactose-based DPI formulations are crucial in the optimization of inhalable medicine performance.

Dry Powder Inhalers Based on Chitosan-Mannitol Binary Carriers: Effect of the Powder Properties on the Aerosolization Performance

Carriers play an important role in improving the aerosolization performance of dry powder inhalers (DPIs). Despite that intensive attention had been paid to the establishment of the advanced carriers with controllable physicochemical properties in recent years, the design and optimization of carrier-based DPIs remain an empiricism-based process. DPIs are a powder system of complex multiphase, and thus their physicochemical properties cannot fully explain the powder behavior. A comprehensive exposition of powder properties is demanded to build a bridge between the physicochemical properties of carriers and the aerosolization performance of DPIs. In this study, an FT-4 powder rheometer was employed to explore the powder properties, including dynamic flow energy, aeration, and permeability of the chitosan-mannitol binary carriers (CMBCs). CMBCs were self-designed as an advanced carrier with controllable surface roughness to obtain enhanced aerosolization performance. The specific mechanism of CMBCs to enhance the aerosolization performance of DPIs was elaborated based on the theory of pulmonary delivery processes by introducing powder properties. The results exhibited that CMBCs with appropriate surface roughness had lower special energy, lower aeration energy, and higher permeability. It could be predicted that CMBC-based DPIs had greater tendency to fluidize and disperse in airflow, and the lower adhesion force between particles enabled drugs to be detached from the carrier to achieve higher fine particle fractions. The specific mechanism on how physicochemical properties influenced the aerosolization performance during the pulmonary delivery processes could be figured out with the introduction of powder properties.

Insights into the potential of rheological measurements in development of dry powder inhalation formulations

Study of flow is a key to development of dry powder inhalation formulations. Various static (bulk) and dynamic rheological measurements are used to study different aspects of powder flow and packing. Among rheological measurements, the permeability and the fluidization energy are, conceptually, most relevant to dispersion of dry powder inhalation formulations. The aim of the current study was to test the robustness and the range of applications of the two measurements, among other rheological measurements. To this end, we prepared and studied a series of ternary, carrier-based dry powder inhalation formulations. The formulations were mixtures of coarse-fine excipient (α-lactose monohydrate) blends, with different fine excipient concentrations (0.0-15.0 % w/w), and a spray-dried drug (fluticasone propionate) material. The excipient blends were characterized in terms of morphology, size, crystallinity and rheological properties. The formulations were evaluated in vitro using a low resistance inhalation device, the Cyclohaler®, and a high resistance inhalation device, the Handihaler®. The study design aimed to complement literature data. Bulk rheological measurements, specifically the bulk density, the compressibility, and the permeability, exhibited satisfactory precision and could demonstrate changes in powder composition and structure. They hold a potential for use as critical material attributes to aid monitoring and optimization of carrier-based dry powder inhalation formulations in quality-by-design systems. On the other hand, dynamic rheological measurements, specifically the basic flowability energy, the specific energy, and the fluidization energy, generally exhibited high variability, which obscured interpretation of the measurements and implied heterogeneous powder structures. The fluidization energy could, nevertheless, convey structural changes taking place during powder fluidization.

Application of Fundamental Techniques for Physicochemical Characterizations to Understand Post-Formulation Performance of Pharmaceutical Nanocrystalline Materials

Nanocrystalline materials (NCM, i.e., crystalline nanoparticles) have become an important class of materials with great potential for applications ranging from drug delivery and electronics to optics. Drug nanocrystals (NC) and nano co-crystals (NCC) are examples of NCM with fascinating physicochemical properties and have attracted significant attention in drug delivery. NCM are categorized by advantageous properties, such as high drug-loading efficiency, good long-term physical stability, steady and predictable drug release, and long systemic circulation time. These properties make them excellent formulations for the efficient delivery of a variety of active pharmaceutical ingredients (API). In this review, we summarize the recent advances in drug NCM-based therapy options. Currently, there are three main methods to synthesize drug NCM, including top-down, bottom-up, and combination methods. The fundamental characterization methods of drug NCM are elaborated. Furthermore, the applications of these characterizations and their implications on the post-formulation performance of NCM are introduced.

Human Health Effects of Lactose Consumption as a Food and Drug Ingredient

Lactose is a reducing sugar consisting of galactose and glucose, linked by a β (1→4) glycosidic bond, considered as an antioxidant due to its α-hydroxycarbonyl group. Lactose is widely ingested through the milk and other unfermented dairy products and is considered to be one of the primary foods. On the other hand, lactose is also considered as one of the most widely used excipients for the development of pharmaceutical formulations. In this sense, lactose has been related to numerous drug-excipient or drug-food pharmacokinetic interactions. Intolerance, maldigestion and malabsorption of carbohydrates are common disorders in clinical practice, with lactose-intolerance being the most frequently diagnosed, afflicting 10% of the world's population. Four clinical subtypes of lactose intolerance may be distinguished, namely lactase deficiency in premature infants, congenital lactase deficiency, adult-type hypolactasia and secondary lactase intolerance. An overview of the main uses of lactose in human nutrition and in the pharmaceutical industry and the problems derived from this circumstance are described in this review.

Development of High Dose Oseltamivir Phosphate Dry Powder for Inhalation Therapy in Viral Pneumonia

Oseltamivir phosphate (OP) is an antiviral drug available only as oral therapy for the treatment of influenza and as a potential treatment option when in combination with other medication in the fight against the corona virus disease (COVID-19) pneumonia. In this study, OP was formulated as a dry powder for inhalation, which allows drug targeting to the site of action and potentially reduces the dose, aiming a more efficient therapy. Binary formulations were based on micronized excipient particles acting like diluents, which were blended with the drug OP. Different excipient types, excipient ratios, and excipient size distributions were prepared and examined. To investigate the feasibility of delivering high doses of OP in a single dose, 1:1, 1:3, and 3:1 drug/diluent blending ratios have been prepared. Subsequently, the aerosolization performance was evaluated for all prepared formulations by cascade impaction using a novel medium-resistance capsule-based inhaler (UNI-Haler). Formulations with micronized trehalose showed relatively excellent aerosolization performance with highest fine-particle doses in comparison to examined lactose, mannitol, and glucose under similar conditions. Focusing on the trehalose-based dry-powder inhalers' (DPIs) formulations, a physicochemical characterization of extra micronized grade trehalose in relation to the achieved performance in dispersing OP was performed. Additionally, an early indication of inhaled OP safety on lung cells was noted by the viability MTT assay utilizing Calu-3 cells.

Exploring the potential influence of drug charge on downstream deposition behaviour of DPI powders

Dry powder inhaler (DPI) development is limited by the time- and labor-consuming in vitro lung deposition test. It's highly desirable to find an easy tool for DPI formulation screening. Dynamic powder rheological properties seem to present many advantages, however, the adoptability needs to be verified. Drug charge is an important parameter especially for DPI formulation design but how it affects the process of pulmonary drug delivery is unavailable. Therefore, the objective of this study is to explore the influence of drug charge on DPI powders, further testing the potentials of powder properties for downstream deposition behavior prediction. Taking five differently charged drugs as model, influence of drug charge on uniformity, rheological and aerodynamic properties of the mixtures were investigated systemically. It was found that mometasone furoate with near neutral charge presented better content homogeneity, while significantly decreased recovery was noted for charged drugs, such as positively charged drug (salbutamol sulphate and indacaterol maleate) mixtures and negatively charged drug (budesonide and fluticasone propionate) mixtures. Moreover, drug charge also influenced flowability and cohesion of their admixture with lactose. As for the downstream deposition, neutral drugs presented higher fine particle fraction (FPF), followed by positively charged drugs and negatively charged drugs. Good correlations between basic flowability energy, aeration energy, Permeability and FPF were established irrespective of different drugs. Principal component analysis results suggested flowability had a greater influence on FPF when mixtures were less cohesive. In conclusion, this study demonstrated drug charge can influence physicochemical, rheological and aerodynamic properties of the admixture, and DPIs' dynamic properties could be used as potential tools to predict downstream deposition with good accuracy.

Effect of Lactose Pseudopolymorphic Transition on the Aerosolization Performance of Drug/Carrier Mixtures

Physico-chemical properties of lactose are key factors in adhesive mixtures used as dry powder inhaler (DPI). Despite the abundant literature on this topic, the effect of the polymorphism and pseudo-polymorphism of lactose has been seldom investigated and discussed although often lactose used in DPI is subjected to unit operations, which may alter its solid-state properties. Here, we studied the aerosolization performance of salbutamol sulphate (SS) or budesonide (BUD) formulations by investigating the effect of lactose pseudopolymorphism in ternary (coarse lactose/fine lactose/drug) and binary (coarse lactose/drug) mixtures. An improvement of the aerosolization performance of SS formulations with the increase of the amount of fine micronized lactose up to 30% (fine particle fraction (FPF) = 57%) was observed. Micronized lactose contained hygroscopic anhydrous α-lactose, which converted to α-lactose monohydrate at ambient conditions. This implied that the positive effect of fines on the aerosolization performance decreased and eventually disappeared with the formulation aging. Positive effect on SS deposition was observed also with binary mixtures with anhydrous lactose, whereas the opposite occurred with budesonide-containing formulations. The collected data demonstrated the crucial role of the carrier crystal form on the positive effect of fines on the deposition.

Fumaryl diketopiperazine based effervescent microparticles to escape macrophage phagocytosis for enhanced treatment of pneumonia via pulmonary delivery

The treatment of pulmonary infections with antibiotics administered via pulmonary delivery provides for higher local therapeutic efficacy rather than through systemic administration. Pneumonia is globally considered a major cause of death due to a lack of proper medication. The treatment of pneumonia with inhalable antibiotics (such as azithromycin (AZM)) can provide a maximum pulmonary therapeutic effect without significant systemic side effects. Compared to non-effervescent microparticles, effervescent microparticles can provide an active driving force to release loaded antibiotics for subsequent distribution deep into the lung by virtue of its smaller size. In this study, N-fumaroylated diketopiperazine (FDKP) was used as a carrier to prepare effervescent inhalable microparticles loaded with AZM (AZM@FDKP-E-MPs). This effervescent dry powder was characterized for both in vitro and in vivo deposition in the lung and the results obtained showed significant improvement in lung deposition and anti-bacterial efficiency, suggesting a strong potential application for pneumonia treatment.

Microstructural characterization of carrier-based dry powder inhalation excipients: Insights and guidance

The growing interest in development of dry powder inhalation (DPI) products raises a need for development of standard testing methods and specifications for DPI excipients. The pharmaceutical industry, meanwhile, yet lacks compendial guidance on this topic. Despite of the complexity of interactions taking place in DPI systems and the large number and variety of interplaying factors, understanding of key determinants of performance (critical quality attributes) of DPI excipients have considerably developed over the past years. In light of the current knowledge in this area, this article provides technical guidance and insights on testing and quality control of carrier-based-DPI excipients. These excipients are, typically, blends of coarse, carrier particles and fine, performance-modulating particles. The article explores techniques used for measurement of key microstructural attributes, namely the particle size distribution, the porosity and the particle surface roughness, the particle shape, rheological properties, and the permeability, of these excipients. The technical relevance of each measurement to the functionality of the excipients is critically discussed. In this regard, caveats concerning use of some measurements and data analysis procedures are raised. The guidance lends itself for compendial adoption.

The Relationship Between the Permeability and the Performance of Carrier-Based Dry Powder Inhalation Mixtures: New Insights and Practical Guidance

The permeability of a powder bed reflects its particle size distribution, shape, packing, porosity, cohesivity, and tensile strength in a manner relevant to powder fluidization. The relationship between the permeability and the performance of carrier-based dry powder inhalation (DPI) mixtures has, however, aroused controversy. The current study sought to gain new insights into the relationship and to explore its potential applications. We studied eight lactose materials as DPI carriers. The carriers covered a broad permeability range of 0.42-13.53 D and moreover differed in particle size distribution, particle shape, crystal form, and/or porosity. We evaluated the performance of inhalation mixtures of each of these carriers and fluticasone propionate after aerosolization from an Aerolizer®, a model turbulent-shear inhaler, at a flow rate of 60 L/min. Starting from the high permeability side, the inhalation mixture performance increased as the carrier permeability decreased until optimum performance was reached at permeability of ~ 3.2 D. Increased resistance to air flow strengthens aerodynamic dispersion forces. The inhalation mixture performance then decreased as the carrier permeability further decreased. Very high resistance to air flow restricts powder dispersion. The permeability accounted for effects of carrier size, shape, and macroporosity on the performance. We confirmed the relationship by analysis of two literature permeability-performance datasets, representing measurements that differ from ours in terms of carrier grades, drug, technique used to determine permeability, turbulent-shear inhaler, and/or aerosolization flow rate. Permeability provides useful information that can aid development of DPI mixtures for turbulent-shear inhalers. A practical guidance is provided.

A New Role of Fine Excipient Materials in Carrier-Based Dry Powder Inhalation Mixtures: Effect on Deagglomeration of Drug Particles During Mixing Revealed

The potential of fine excipient materials to improve the performance of carrier-based dry powder inhalation mixtures is well acknowledged. The mechanisms underlying this potential are, however, open to question till date. Elaborate understanding of these mechanisms is a requisite for rational rather than empirical development of ternary dry powder inhalation mixtures. While effects of fine excipient materials on drug adhesion to and detachment from surfaces of carrier particle have been extensively investigated, effects on other processes, such as carrier-drug mixing, capsule/blister/device filling, or aerosolization in inhaler devices, have received little attention. We investigated the influence of fine excipient materials on the outcome of the carrier-drug mixing process. We studied the dispersibility of micronized fluticasone propionate particles after mixing with α-lactose monohydrate blends comprising different fine particle concentrations. Increasing the fine (D < 10.0 μm) excipient fraction from 1.84 to 8.70% v/v increased the respirable drug fraction in the excipient-drug mixture from 56.42 to 67.80% v/v (p < 0.05). The results suggest that low concentrations of fine excipient particles bind to active sites on and fill deep crevices in coarse carrier particles. As the concentration of fine excipient particles increases beyond that saturating active sites, they fill the spaces between and adhere to the surfaces of coarse carrier particles, creating projections and micropores. They thereby promote deagglomeration of drug particles during carrier-drug mixing. The findings pave the way for a comprehensive understanding of contributions of fine excipient materials to the performance of carrier-based dry powder inhalation mixtures.

On the effects of blending, physicochemical properties, and their interactions on the performance of carrier-based dry powders for inhalation - A review

Blending drug and carrier powders to produce homogeneous drug-carrier adhesive mixtures is a key step in the production of dry powder inhaler (DPI) formulations. Although the blending conditions can result in different conclusions or probably change the outcome of a study entirely if being selected differently, there is a scarcity of data on the influence of blending processes on the physicochemical properties of bulk powder formulations and the follow-on effects on DPI performance. This paper provides an overview of the interactions between variables related to blending conditions (e.g. blending equipment, time, speed and sequence as well as environmental humidity) and powder physicochemical properties (e.g. size distribution, shape distribution, density, anomeric composition, electrostatic charge, surface, and bulk properties), and their effects on the performance of adhesive mixtures for inhalation in terms of drug content homogeneity, drug-carrier adhesion, and drug aerosolisation behaviour. The relevance of carrier payload, batch size and segregation was also discussed. Challenges and future directions were identified. This review therefore contributes towards a better understanding of the blending process, powder physicochemical properties, and their interlinked effects on the fundamental understanding of adhesive mixtures for inhalation. The knowledge gained is essential to ensure optimum blending and thereby controlled functionality of DPIs.

Evaluation of granulated lactose as a carrier for DPI formulations 1: effect of granule size

The objective of this study was to investigate the effect of large granulated lactose carrier particle systems on aerosol performance of dry powder inhaler formulations. Granulated lactose carriers with average sizes ranging from 200 to 1,000 μm were prepared and subsequently fractionated into separate narrow size powders. The fractionated granulated lactose (GL) samples were characterized in terms of size, specific surface area, surface roughness, morphology, density, flowability, and solid-state. The in vitro aerosolization performance was performed on the different size fractions of GL samples from a commercial inhaler device (Aerolizer®) with a model formulation (2% w/w salbutamol sulfate). The cascade impaction parameters employed were 60 or 90 L/min with standard (aperture size, 0.6 mm) or modified piercing holes (aperture size, 1.2 mm) of the inhaler loaded capsules. It was shown that the largest size fraction formulation (850-1000 μm) had a slight improvement in the fine particle fraction (FPF) compared to immediately preceding size fractions, explained by a smaller adhesive force between drug and carrier. Compared to commercial piercing holes, enlarged piercing holes generated a slight decreasing trend of FPF as the lactose powder sizes increased from 200-250 μm to 600-850 μm, perhaps due to the reduced detachment force by flow forces. The size, surface roughness, density, and flowability of lactose carrier as well as device design all contributed to the aerosol dispersion performance of granulated lactose-based adhesive mixtures. It was concluded that poorer or enhanced redispersion performance is not an inherent property to the significantly large size of granulated lactose carriers as previously contended.

Defining the critical material attributes of lactose monohydrate in carrier based dry powder inhaler formulations using artificial neural networks

The study aimed to establish a function-based relationship between the physical and bulk properties of pre-blended mixtures of fine and coarse lactose grades with the in vitro performance of an adhesive active pharmaceutical ingredient (API). Different grades of micronised and milled lactose (Lactohale (LH) LH300, LH230, LH210 and Sorbolac 400) were pre-blended with coarse grades of lactose (LH100, LH206 and Respitose SV010) at concentrations of 2.5, 5, 10 and 20 wt.%. The bulk and rheological properties and particle size distributions were characterised. The pre-blends were formulated with micronised budesonide and in vitro performance in a Cyclohaler device tested using a next-generation impactor (NGI) at 90 l/min. Correlations between the lactose properties and in vitro performance were established using linear regression and artificial neural network (ANN) analyses. The addition of milled and micronised lactose fines with the coarse lactose had a significant influence on physical and rheological properties of the bulk lactose. Formulations of the different pre-blends with budesonide directly influenced in vitro performance attributes including fine particle fraction, mass median aerodynamic diameter and pre-separator deposition. While linear regression suggested a number of physical and bulk properties may influence in vitro performance, ANN analysis suggested the critical parameters in describing in vitro deposition patterns were the relative concentrations of lactose fines % < 4.5 μm and % < 15 μm. These data suggest that, for an adhesive API, the proportion of fine particles below % < 4.5 μm and % < 15 μm could be used in rational dry powder inhaler formulation design.

An investigation into the effect of fine lactose particles on the fluidization behaviour and aerosolization performance of carrier-based dry powder inhaler formulations

The effect of milled and micronized lactose fines on the fluidization and in vitro aerosolization properties of dry powder inhaler (DPI) formulations was investigated, and the suitability of static and dynamic methods for characterizing general powder flow properties of these blends was assessed. Lactose carrier pre-blends were prepared by adding different lactose fines (Lactohale® (LH) 300, 230 and 210) with coarse carrier lactose (Lactohale100) at 2.5, 5, 10 and 20 wt% concentrations. Powder flow properties of lactose pre-blends were characterized using the Freeman Technology FT4 and Schulze RST-XS ring shear tester. A strong correlation was found between the basic flow energy (BFENorm) measured using the Freeman FT4 Rheometer and the flowability number (ffc) measured on Schulze RST-XS. These data indicate that both static and dynamic methods are suitable for characterizing general powder flow properties of lactose carriers. Increasing concentration of fines corresponded with an increase in the normalized fluidization energy (FENorm). The inclusion of fine particles of lactose resulted in a significant (p < 0.05) increase in fine particle delivery of budesonide and correlated with FENorm. This trend was strongest for lactose containing up to 10 wt% LH300. A similar trend was found for the milled lactose grades LH230 and LH210. However, the increase in FENorm upon addition of milled fines only corresponded to a very slight improvement in the performance. These data suggest that whilst the fluidization energy correlated with fine particle delivery, this relationship is specific to lactose grades of similar particle size.

Advanced microscopy techniques to assess solid-state properties of inhalation medicines

Efficient control and characterisation of the physico-chemical properties of active pharmaceutical ingredients (APIs) and excipients for orally inhaled drug products (OIDPs) are critical to successful product development. Control and reduction of risk require the introduction of a material science based approach to product development and the use of advanced analytical tools in understanding how the solid-state properties of the input materials influence structure and product functionality. The key issues to be addressed, at a microscopic scale, are understanding how the critical quality attributes of input materials influence surface, interfacial and particulate interactions within OIDPs. This review offers an in-depth discussion on the use of advanced microscopy techniques in characterising of the solid-state properties of particulate materials for OIDPs. The review covers the fundamental principles of the techniques, instrumentation types, data interpretation and specific applications in relation to the product development of OIDPs.

Physico-chemical aspects of lactose for inhalation

A dry powder inhaler (DPI) is a dosage form that consists of a powder formulation in a device which is designed to deliver an active ingredient to the respiratory tract. It has been extensively investigated over the past years and several aspects relating to device and particulate delivery mechanisms have been the focal points for debate. DPI formulations may or may not contain carrier particles but whenever a carrier is included in a commercial formulation, it is almost invariably lactose monohydrate. Many physicochemical properties of the lactose carrier particles have been reported to affect the efficiency of a DPI. A number of preparation methods have been developed which have been claimed to produce lactose carriers with characteristics which lead to improved deposition. Alongside these developments, a number of characterization methods have been developed which have been reported to be useful in the measurement of key properties of the particulate ingredients. This review describes the various physicochemical characteristics of lactose, methods of manufacturing lactose particulates and their characterization.

Lactose characteristics and the generation of the aerosol

The delivery efficiency of dry-powder products for inhalation is dependent upon the drug formulation, the inhaler device, and the inhalation technique. Dry powder formulations are generally produced by mixing the micronised drug particles with larger carrier particles. These carrier particles are commonly lactose. The aerosol performance of a powder is highly dependent on the lactose characteristics, such as particle size distribution and shape and surface properties. Because lactose is the main component in these formulations, its selection is a crucial determinant of drug deposition into the lung, as interparticle forces may be affected by the carrier-particle properties. Therefore, the purpose of this article is to review the various grades of lactose, their production, and the methods of their characterisation. The origin of their adhesive and cohesive forces and their influence on aerosol generation are described, and the impact of the physicochemical properties of lactose on carrier-drug dispersion is discussed in detail.